Search Documents

By Mark Sheppard

DuRing the winter of 1937, the writer visited a West Virginia stone quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide. The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the overburden was dug by hand labor, dumped to the quarry floor and transported to the dump in quarry cars. Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semicircle around the top of the quarry about 200 ft. from the face and about 50 ft. above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river. As quarrying progressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp., 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft. above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting bays into which the motors are raised whenever the river reaches flood stage. An 8-in. suction line, equipped with a strainer and a foot valve, takes the water from a concrete sump at the edge of the river. The pipe line from the pump consists of 1750 ft. of 8-in. spiral steel flanged pipe and

Jan 1, 1938

By Mark Sheppard

DuRing the winter of 1937, the writer visited a West Virginia stone quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide. The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the overburden was dug by hand labor, dumped to the quarry floor and transported to the dump in quarry cars. Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semicircle around the top of the quarry about 200 ft. from the face and about 50 ft. above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river. As quarrying progressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp., 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft. above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting bays into which the motors are raised whenever the river reaches flood stage. An 8-in. suction line, equipped with a strainer and a foot valve, takes the water from a concrete sump at the edge of the river. The pipe line from the pump consists of 1750 ft. of 8-in. spiral steel flanged pipe and

Jan 1, 1938

By James W. Neill

Discussion of the paper of H. 0. Hofman, presented at the Canal Zone meeting, November, 1910, and printed in Bulletin No. 42, June, 1910, pp. 473 to 497. JAMES W. NEILL, Pasadena, Cal. (communication to the Secretary *) :-Professor Hofman's paper brings the art up to . date. As I was one of the pioneers in this business, I beg to give the following incomplete data regarding my efforts in this line. In the year 1883, while I was in charge of the smelting-operations at Mine La Motte, Mo., there was at the concentrator an unusually large production of a middle product, locally called "iron," which carried considerable values in nickel and cobalt, and which it was desirable, for this reason, to treat by itself. The works could not spare a furnace for the purpose; and to handle this product I improvised a "roast-hearth " from an old " lead-hearth." This was a small cast-iron furnace of the usual construction, about 2 by 4 ft. in dimensions, with a hollow cast-iron back, through which the wind circulated before entering the tuyeres. I had a cast-iron grate made to fit this hearth, and placed it flush with the lip, or apron, and above the tuyeres. On this grate, which had round holes about 0.25 in. in diameter, and a total surface of about 20 by 40 in., I roasted the nickeliferous pyrite product; starting the fire with kindling, then adding charcoal, and then gradually feeding the sulphides with a shovel, so as to cover the fire, choke down blow-holes, and get an even bed. Blast at a pressure of 3 or 4 oz. was supplied by a fail-blower. When a cake of roasted material had formed, it was removed with a steel bar, or fork, to the lip of the furnace, and thence into a wheel-barrow.. The fine material which had remained unmelted, but very hot, on top of the cake would promptly ignite when the cake was broken up and removed. The fire would then be covered with fresh material and * Received Aug. 29, 1910.

Apr 1, 1911

By W. A. McCurdy, Joseph W. Leonard, William F. Lawrence

INTRODUCTION Utilization from the Point of View of the Preparation Engineer The primary interest of the coal preparation engineer is in process design, operation, and maintenance to produce an acceptable product that can be sold at the greatest possible profit. Because of emphasis upon these interests, attention to other potential values of coal is sometimes neglected. The intent of this chapter is to alert the preparation engineer to the utilization possibilities of the product as well as the tributary coal flow moving through a modern coal preparation plant. The basis for any unrealized potential derives directly from the coal seam itself. Most coal seams consist of coal bands and benches sandwiched together in layers that differ visually from each other in physical structure and luster. Randomly selected physical and chemical ranges determined from layers of coal in a single seam can easily differ by as much as 30 Hardgrove grindability indices, 0.30 of a specific gravity point, 20 percentage points of ash, 6 percentage points of dry volatile matter, and 10 percentage points of total su1fur.l Similar wide variations exist for calorific value, seam moisture content, and, undoubtedly, for any other conceivable coal test parameter that might be used for comparative purposes. These observations all point to the long-established fact that coal is not homogeneous, as conventional analytical methods might tend to indicate, but is instead a highly heterogeneous substance.

Jan 1, 1979

By J. W. Cunningham, M. J. Stultzman

THE demand for improved materials for high-temperature service has increased during the last few years. Iron,- nickel,- and cobalt-base alloys have been investigated extensively and many alloys with outs'tanding high-temperature strength have been developed. Considerable research has been directed toward improved methods of processing these alloys. The vacuum furnace as a tool for the purification and improved control of high-temperature alloys has been studied extensively and production units are in operation. The research covered by this paper studied the effects of casting in air, vacuum, or argon upon the elevated-temperature properties of two nickel- and two cobalt-base alloys. The alloys investigated were Stellite 31, He 1049, Udimet 500, and Guy Alloy. MELTING AND CASTING PROCEDURES Two heats of each of the four alloys under investigation were melted and investment cast under the following conditions: 1) Stellite 31 was melted and investment cast in air and in vacuum, with an argon atmosphere for pouring. 2) He 1049 was melted and investment cast in air and in vacuum, with an argon atmosphere for pouring. 3) Udimet 500 was melted and investment cast in vacuum with and without additions of zirconium and boron. 4) Guy Alloy was melted and investment cast in vacuum and in argon. The heats were all melted in induction furnaces equipped with preformed magnesia crucibles of 50-lb capacity. The air-melting furnace was powered by a spark-gap converter of 40 kw capacity. The vacuum-melting furnace was powered by a motor-generator set of 100 kw capacity. The argon heat of Guy alloy was melted in the vacuum melting furnace under an argon atmosphere. Virgin materials were used for preparing all heats except the air heats of Stellite 31 and He 1049. The charge for the air heat of Stellite 31 was a commercial blend of shot. The charge for the air heat of He 1049 was Stellite 6 shot plus those virgin materials necessary to give the desired composition. All of the materials used were of the same grade used com-

Jan 1, 1960

By Thomas A. Steven

Most mineralized areas in the central San Juan Mountains, Colorado, are associated with the youngest subsidence structures in a large volcanic cauldron complex that formed concurrently with eruption of the surrounding ash-flow field. Two local types have been recognized: (1) fissure-vein deposits along faults characterized by relatively late movement, and (2) hydrothermally altered and mineralized areas associated with postsubsidence Fisher Quartz Latite centers. The first type has provided most production in the past; the potential of the second type has yet to be adequately tested.

Jan 1, 1968

By David White

THE submission of carefully prepared estimates of the oil reserves of the United States calls for no apology or explanation. In this country, petroleum is a rapidly wasting asset and an occasional appraisal of the amount remaining in the ground is a simple business procedure to safe-guard the general welfare and the prosperity of the republic. The rumored danger of failure, in the near future, of the foreign supply on which we depend in constantly increasing amounts makes the immediate review of our available reserves the more imperative. The Director of the U. S. Geological Survey, in March, 1921, requested the American Association of Petroleum Geologists to cooperate in the preparation of new estimates of the oil remaining in the ground. With the members of this cooperative committee, state geologists, regional geologists, consulting specialists, and geologists and engineers attached to many companies worked both independently and through sub-committees. The reports for districts, counties, fields, etc., after review by local or state committees, were discussed by the joint cooperative committee in conferences that, in some instances, were attended by the original compilers of estimates for the states or smaller areas. Finally the data were reviewed and the figures revised by the joint cooperative committee, so that the totals given in Table 1 represent the opinion of the committee, which was composed of F. W. DeWolf, W. E. Wrather, Roswell H. Johnson, Wallace A. Pratt, Alexander W. McCoy, Carl H. Beal, C. T. Lupton, G. C. Matson, K. C. Heald, W. T. Thom, Jr., A. E. Fath, Kirtley F. Mather, R. C. Moore, and David White, chairman.

Jan 6, 1922

By Harry E. Krumlauf

The year 1957 was one of declining metal price and production. Many lead-zinc-copper mines were forced to close, and the remaining mines limited production to stay more in line with demand. High cost of labor, supplies, and equipment and high taxes aggravated the situation. Some operators postponed or abandoned expansion programs because of uncertain economic conditions. Output was curtailed by elimination of over- time employment and reduction of the working force. The number of employes laid off was small- reduction in the labor force was accomplished by not replacing those who left a company's employ.

Jan 2, 1958

Remarks of Mr. Robert W. Hunt, General, Superintendent, Albany and Rensselaer Iron and Steel Company., Troy N. Y.—In discussing Dr. Dudley's two most interesting papers, I feel a natural hesitancy in disagreeing with conclusions formed after such careful and conscientious work. But I think he has made his deductions from too meagre premises. The analyses of but twenty-five samples are entirely too few to justify the establishment of so important a formula. When we consider that he indirectly proposes to regulate an interest amounting, even at the present low prices, to over $20,000,000 per annum, we may well hesitate before accepting a formula based upon the chemical and physical analyses of but twenty-five steel rails. Dr. Dudley touches the keynote in referring to the proposed labors of the Government Test Commission. They based their hopes of attaining success upon the chemical and physical analyses of a very large number of samples, and in the only branch of investigation which the short-sighted policy of Congress has allowed them to complete, i.e., chain cables, we find that a dozen, twenty-five or one hundred tests gave no satisfactory results. It was only after many hundreds that they were enabled to' draw conclusions. There are so many circumstances hearing upon the life of a rail, that the task of extracting a correct result seems herculean. I presume I am right in stating that in our Northern latitudes early winter and spring months witness the breaking of the greatest number of rails, thus seeming to prove that an unstable road-bed has much to answer for. Then, again, broken and flattened wheels must be taken into account, but I am convinced that more rails have been broken by the treatment which they received before leaving the rolling-mill

Jan 1, 1879

By Charles N. Bell

The Telluride mining district of southwestern Colorado is defined by the 37" 45' and 38" parallels of latitude and 107" 45' and 108" meridians of longitude. Telluride was never a boom camp, but has had a steady growth. In recent years, notwithstanding the business depression of 1920, the business has been the same as in normal years. The first prospector is said to have appeared in 1875, in which year locations on the Smuggler vein were made. Shipments were made in 1877 and 1878, and in 1879 milling the ores was attempted. While the district produced high-grade ores, it did not become important until 1890, when the Rio Grande Southern R. R. was completed from Ridgway to Telluride. The railroad has since been extended to Durango. In the fall of 1896, 400 stamps were in operation, and the annual production was $3,000,000.00, two-thirds of which was gold. The total production from 1875 to 1923 was: gold $58,274,527; silver 41,-830,920 oz., valued at $31,016,893; copper 15,258,866 lb., valued at $2,533,291; lead 166,056,484 Ib., valued at $8,324,910; zinc 18,141,182 Ib. valued at $1,323,787; or a total production of $101,473,408. All claims are held in fee. Most of them are 1500 by 300 ft. but claims located within the last few years are 1500 by 600 ft. General supplies are obtained at Telluride, Denver, and Salt Lake. The largest mines are within 6 miles of the town of Telluride. Denver is 422 miles and Salt Lake is 439 miles, by rail, from Telluride. One-half of the distance to Denver and one-sixth of the distance from Telluride to Salt Lake is by narrow-gage railroad. The labor is efficient. The best miners are Italians and Austrians, then Slavs, Greeks, and Mexicans follow in the order mentioned. There are no labor unions. There are no serious mine pumping problems, the drainage being through adits. The Tomboy and Smuggler companies pump water from their reservoirs, the former for milling and domestic purposes and the latter for milling, power, and domestic purposes. BIBLIOGRAPHY A partial bibliography of the Telluride District is: Geologic Atlas Telluride No. 57; Preliminary Report on the Mining Industries of the

Jan 1, 1925

By J. W. Rutter, K. T. Aust

The temperature dependence of the rate of grain boundary migration was measured in bicrystals of zone-refined lead containing from 20 to less than 1 ppm by wezght of tin. The apparent activation energy in the temperature range from 320" to 200oC is markedly dependent upon the solute tin concentration and upon the orientation relationship of the grains adjacent to the grain boundavy. The quantitative experimental observat~ons are compared with the predictions of various theories of grain boundary migration. In previous work.&apos;?&apos; the mobility of individual grain boundaries was studied as a function of impurity concentration and type of boundary. Grain boundary migration occurred at the expense of dislocation arrays which were introduced into the specimen during solidification. Boundary mobility in zone-refined lead at 300°C was markedly decreased by small additions of tin. 0.004 wt pct being sufficient to decrease the rate of grain boundary migration by a factor of 1000. The mobility of grain boundaries having polar orientation relationships near 38 and 22 deg about <Ill>, and 28 deg about <100>, was much less sensitive to tin concentration in the range studied. As a result, these boundaries have relatively high mobilities. The present paper is a continuation of the above study. Data are now presented on the temperature dependence of the motion of individual grain boundaries in zone-refined lead as a function of solute tin concentration and orientation relationship of adjacent grains at the grain boundary. The experimental observations are compared with the predictions of a number of theories of grain boundary migration3-8 which, prior to the present experimental investigation, could not be critically evaluated. EXPERIMENTAL PROCEDURE The striation or lineage structure of melt-grown single crystals of zone-refined lead, containing various additions of tin, was utilized to provide a driving force for grain boundary migration, as previously described.1,2 Each grain boundary under study separated the striated single crystal from another grain which was introduced by localized plastic deformation and recrystallization of a small region of the sample. The speed of migration of grain boundaries in dilute alloys of tin in zone-refined lead was investigated as a function of 1) tin concentration from < 0.0001 to 0.002 wt pct, 2) temperature in the range of 200" to 320°C, and 3) orientation relationship of the adjacent grains at the grain boundary. The substructure driving energy available for grain boundary migration was estimated to be about 4000 ergs per cu cm, within a factor of two, from specimen to specimen.&apos; The specimen dimensions, and growth and alloying procedures for the preparation of striated single crystals of lead of known tin composition, were as described previously.&apos; Each bicrystal was carefully wrapped in aluminum foil, and annealed in a well-stirred salt bath consisting of 50 pct NaNO2 and 50 pct KNO3, for known periods of time at a series of constant temperatures (*2°C). The grain boundary positions, before and after each anneal, were determined by etching lightly in a solution of 5 pct nitric acid in methyl alcohol, in order to follow the motion of the boundary and determine its rate of migration. Thus, the rate of motion of the grain boundary in a single specimen was measured at various temperatures. The above procedure was carried out for each grain boundary in seventeen different bicrystal specimens.

Jan 1, 1960

By J. L. Bruce, N. B. Braly, F. A. Linforth, Wm. B. Daly, Paul A. Gow, C. L. Berrien, R. H. Sales, P. F. Beaudin, John Gillie, G. W. Roddewig

Butte mining district is situated in Silver Bow County, in the southwestern part of Montana. Butte originated as a placer mining camp, gold having been discovered in 1864, on Silver Bow Creek, near the southerly end of what is now Main Street. The Butte placer gold was heavily alloyed with silver, and only commanded $13 an ounce. Placer mining was vigorously prosecuted along Silver Bow Creek and its tributary gulches for about 5 years, at the end of which time, in 1870, the Butte camp was practically deserted. In the meantime, the quartz veins prominently traceable over the hillsides were located, the first location, July 12, 1864, being made by the Missoula Mining Co. and called the Missoula Lode Claim, and later relocated by G. 0. Humphreys. Reasoning from the presence of the gold placers, free milling gold and silver ores were eagerly looked for by the early prospectors. Claims covering the great Rainbow and other silver lodes were located in the 60&apos;s. The presence of valuable silver ores in these veins caused the staking of many claims, believed to be valuable only for silver, but which later, at depth, proved to be enormous copper producers.

Jan 1, 1925

By Thomas Fraser, David R. Mitchell

THE primary purpose of the loading plant is to transfer the finished product from the preparation machines to the railroad car, truck, or barge in which it is to go to market. Secondary purposes of the loading plant are: to prevent excessive degradation of sizes during loading, to reduce segregation as much as possible, and to prevent excessive quantities of very good or off-grade coal from entering any one car. Nonuniformity of consignments is one of the chief sources of com- plaints by consumers and coal merchants. A properly designed loading plant will do much to reduce complaints and ensure uniformity, not only from shipment to shipment but also in each individual consignment along the length of the car and in cross section. DEGRADATION IN STORAGE, LOADING AND SHIPMENT The object in loading is not only to handle the coal without breakage and segregation, but also to produce a well-trimmed load that will ride to its destination without spillage or breakage en route. The small sizes present in a car of prepared coal as received by the purchaser consist-of: missed small sizes not screened out in the preparation plant, breakage during loading, and breakage caused by handling en route. For domestic sizes of anthracite shipped from the Pennsylvania anthracite field to Atlantic coast cities, the dealers&apos; lass because of breakage in loading and shipment amounts to from 2 to 5 per cent and for anthracite shipped to Middle West cities, the loss is 8 to 9 per cent. This difference is in part because dealers in the Middle West rescreen their coal more thoroughly than is usual in the East. One dealer handling Illinois No. 6 coal shipped from southern Illinois mines to Chicago reports an average size loss of 10 per cent when lump coal is unloaded with a fork. This runs as low as 5 per cent for carefully loaded coal and as high as 15 per cent for carelessly loaded coal.

Jan 1, 1943

By Cornelius F. Kelley

EVERY man connected with the mining industry should take a significant pride in the fact that he belongs to an industry and to a profession that, from the beginning, has been constructive. The miner digs his ore and he gives the metal to art, to industry, and to commerce. The nature of our business is destructive only in that we deal with a wasting asset. That should be a source of great pride to those who belong to the profession. But unfortunately, the product of our mines, our smelters, and our re- fineries does not always go to constructive purposes. There are times when, in the administration of the affairs of men, our product chiefly goes to purposes which are destructive. When we look upon the panorama of horror that is being enacted throughout the world today, we wonder whether any effort toward the development of civilization and culture and education and well-being has been worthwhile. We are appalled to see the things that have been developed, through the application of science, toward progress and efficiency, now used for the catastrophic destruction of those things which are the most valuable that man has built. We must find hope that this is but an episodic thing; that it must, in the infinite wisdom of the Almighty, usher in a period of peace and progress, of civilization and development that will make man&apos;s existence upon earth worthwhile.

Jan 1, 1941

By George D. Graffin.

The first use of graphite is lost in the mists of time. It was used by primitive man to make drawings on the walls of caves and by the Egyptians to decorate pottery. As early as 1400 A.D. graphite crucibles were being made in the Haffnerzell district of Bavaria. Through the Middle Ages graphite was confused with other minerals, especially galena and molybdenite. Two common names that are still used for the mineral are "Plumbago," meaning leadlike, and "Black Lead." The latter name implied that graphite is either composed of lead or at least contains a large percentage of it. Gessner is credited with having recognized it as a separate mineral in 1565, but its composition was not determined until 1779, when Scheele demonstrated that graphite oxidized to carbon dioxide, thus proving its carbon constitution. In 1789, Werner named it "graphite" from the Greek word "graphein," meaning to write. The United States has long relied on foreign countries for its graphite supplies. This reliance has been due more to the lack of suitable domestic graphites than to any particular preference for buying minerals overseas. Ceylon (now Sri Lanka) graphites were imported as early as 1820, and Madagascar graphites have been imported since the properties on that island were opened up about a hundred years later. Mexico has long supplied the United States with most of its requirements for amorphous graphite. Physical Properties and Classification Graphite is found in laminated, flaky aggregates disseminated in schistose rocks. It also occurs in veins and exhibits a foliated or fibrous structure. Graphite is a black lustrous mineral that crystallizes in the hexagonal system, with rhombohedral symmetry. The crystals have tabular form and are six-sided; the faces are commonly striated. The flakes have perfect basal cleavage and are opaque. When well crystallized, the flakes have a black metallic luster while the amorphous material is black and earthy, with a microcrystalline compactness. The flakes feel greasy. Graphite is an excellent conductor of heat and electricity. It melts at approximately 3550°C at a triple point under 1250 psi. It sublimes between 3300-3500°C at 14.7 psi. At 3726°C a second triple point occurs at approximately 100,000 atmospheres. Thermal oxidation in the presence of oxygen begins at 300°C and the rate increases with temperature. The three forms of carbon (charcoal, graphite, and diamond) are distinguished by chemical and physical tests. The specific gravity of charcoal is 1.3 to 1.9, of graphite 2.266 g/ cm3 (crystal density), and of diamond 3.5. Graphite has a hardness of 1 to 2 (Mohs&apos; scale). Natural graphite can be divided into three classes: disseminated flake, crystalline vein (fibrous or columnar), and amorphous. Flake graphite is a lamellar form found in metamorphic rocks, such as marble, gneiss, and schist. Each flake is separate, having crystallized as such in the rock. Crystalline vein graphite is found in the form of well defined veins or as pocket accumulations along the intrusive contacts of pegmatites with limestones. The graphite of such deposits is of two types, foliated and columnar. The important Sri Lanka (Ceylon) deposits are vein type. Amorphous graphite is commonly found as minute microcrystalline particles more or less uniformly distributed in feebly metamorphic rocks, such as slates and shales, or in beds consisting practically entirely of graphite. The latter usually are metamorphosed coal seams and carry as much as 80-85% graphitic carbon, while the former, being altered carbonaceous sediments, commonly range from 25 to 60%

Jan 1, 1983

By John K. Irwin

Friction hoisting has assumed a major role since its introduction to North America less than ten years ago. Interest was illustrated by a recent visit of the Adirondack Section of AIME to a new friction hoist at Chateaugay mine of Republic Steel Corp. at Lyon Mountain, N. Y. The 80-in. diam, 4-rope machine at Lyon Mountain is typical of modern friction hoists. The hoist is mounted on a structural steel tower without deflection sheaves.

Jan 10, 1963

MEMBERS, JUNIOR MEMBERS, ASSOCIATES AND JUNIOR ASSOCIATES LIST OF MEMBERS ALPHABETICALLY ARRANGED EXPLANATION OF SYMBOLS ** Junior Member. t Associate. || Junior Associate. Members are not marked. Capital letters signify Honorary membership. Student Associate and Rocky Mountain members on pages 165-167. Abadilla. Quirico A Catanawan. Tayabas, P. I. Abbey. Robert Graham. District Mgr The W. W. Sly Mfn. Co., 60 Church St New York. N. Y. Abbott. A. N Mines Supt Mazapil Copper Co Ltd . .Conception del Oro. Zac., Mexico. Abbott. Ckrence E Mgr Mines & Quarries, Tenn. Coal. Iron & R. R. Co 1242 Brown Marx Bldg Birminrham. Ala. Abbott. Louie Benjamin. Chief Enar Consolidation Coal Co Elkhorn Div .Jenkins, KY. Abeel. Gsorge H Jr., Cons. Min. Enar .Box 427. Santa Monica. Cal. Abel. Albert E Asst. to Pres Valley Mould & Iron Corp Hubbard. Ohio. Abel. Raymond L. Asst. Prof., Dept. of Pet. Refin Univ. of Pittsburgh Pittsburgh. Pa. Abernathy. George Elmer. Prof. of Geol. & Min Kansas State Teachers College. Pittsburg. Kans. IlAbernethy. D. Carl, Jr. Min. Engr Hudson Coal Co .Scranton. Pa. Abey, Hiroshi. Min. & Met. Engr., Min. & Met. Dept., The Higher Technical School, Osaka. Japan. tAbarn, Robert H Instructor in Met Harvard University Cambridge, Mass tAbozeid,Mahmood. Pet. Production E r . . Marland Oil Co. Ponca City, Okla. Abraham. Arthur W Geol., Richfield Oil Co Box 788. Bakersfield, Cal. Abraham, W. E. V Member, Staff of Burmah Oil Co Ltd. Nyaunghla. Upper Burmz, India. Abrahams. Alexander I Gen&apos;l Mgr., Racon Electrical Co Slough, Bucks England. tAbrahammn. C. W Min. Engr The Mond Nickel Co Ltd . Coniston, Ont Canada. IlAbmn. Guy W., Asst. Metallographist, Youngstown Sheet & Tube Co., Research Dept., Youngstown. Ohio. Abstein. Henry T., Engr. & Mgr Profile-Tamarack Mines Co . .Yellow Pine, Idaho. tAcker. E. O&apos;C Met I28 East Washington Lane. Germantown, Philadelphia. Pa. Ackerman. D. E Met. Research Lab International Nickel Co Inc Bayonne. N. J. tAbckerman. Ernest R Pres., Lawrence Portland Cement Co . .Plainfield. Union Co N. J. ||Ackerman. George F Jr. Min. Engr El Potosi Min. Co. .Apt. 13. Chihuahua, Chih Mexico. Acres, T. H Geol. Dept Valuation & Pet. Engr., Richfield Oil Co. 655 S. Flower St Los Angeles. Cal. Adachi. Jinzoo Address Wanted. Adair. Arthur C Valuation Enar., Internal Revenue. Treasury Dept., Washington, D. C. Adam. John. Min. Ennr., The Zinc Corp. Ltd., Box 4 C. Broken Hill, N. S. W Australia. Adami. Arthur E V. P Montana State School of Mines.Butte, Mont. Adami. Charles J Min. Ensr St. Joseph Lead Co 4540 Lindel Blvd., St. Louis, Mo. Adams. C. W.729 South Normandie St LaGranada Apt Los Angeles, Cal. Adams. Cmyler Geerwwd. Minn. Adams. F. J Gen&apos;l Anent. Gulf Production & Pipa Line Cos .Fort Worth. Tex. ADAMS. FRANK DAWSON. Logan Prof. of Geology and Dean, Faculty of Applied Science, McGill Univ Montreal. Que Canada. Adama, Gale L Research Enar., General Pet. Corp. of California, Higgins Bldg Los Angeles. Cal. Adams. George I, Prof. of Geol. & Mineralogy Univ. of Alabama, Tuscaloosa, Ala. Adams. H. H Cons. Geol Room 416, W. T. Waagoner Bldg Fort Worth. Tex. Adams, Henry. Cons. Min. Ennr 1050 Edgewood Ave., Plainfield, N. J. Adams, Henry H.285 Madison Ave., New York. N. Y. Adams, Henry Farnum. Engr., Charge. Experimental Work. Inspiration Concentrator, Inspiration Cons. Copper Co Box 354. Inspiration. Ariz. Adams. Huntington. Min. Enar I41 Broadway, New York. N. Y. Mama, Leland D., V. P., Leslie-California Salt Co 166 Montgomery St., San Francisco, Cal. Adams, Louis W., Illinois Steel Co .Gary. Ind.

Jan 1, 1929

By G. E. Tardiff, A. A. Hendrickson

THE objectives of this communication are to present the solid-solution strengthening data for silver-base zinc single crystals and to evaluate the importance of strength contributions from several mechanisms through the use of this data combined with that for the silver-base aluminum case.&apos; Some features of the yield point behavior of silver-base zinc crystals were previously reported.&apos; Silver-base zinc alloys were prepared by induction melting 99.99 pct Ag with 99.9 pct Zn in high-purity graphite crucibles contained in argon-filled quartz tubes. After the first melting, the ingots were cut into short lengths, redistributed in the molds, and remelted in order to reduce solute-concentration variations. Alloy single crystals were then grown from the melt through the use of a modified Bridgeman technique which consisted of lowering the graphite crystal mold through a hot zone at a rate of 3/8 in. per hr. As in the melting operation, the molds were contained in argon-filled quartz tubes. Gage lengths 2 cm in length were introduced by both spark machining (circular cross sections) and abrading and acid etching (rectangular cross section) followed by electropolishing (a comparison of the critical resolved shear-stress values prepared by the two techniques showed no differences in strength values). The final cross-sectional areas of the crystals were approximately 5 sq mm. Prior to testing, the crystals were annealed at 600°C for 20 hr in argon atmospheres, furnace-cooled, and lightly electropolished. Crystal orientations were determined using the back-reflection method. The tensile testing was done on a Model FM Instron at a strain rate of 1(T4 per sec. Test temperatures of 77", 200°, and 400°K were attained by immersing the specimens in liquid nitrogen, dry ice-acetone mixtures, and silicone oil, respectively. The critical resolved shear-stress (CRSS) values for silver-base zinc crystals as a function of composition and testing temperature are given in Fig. 1. It will be noted that the CRSS for silver-base zinc solid solutions, as in the silver-base aluminum1 case, depends on temperature in a manner typical of fcc solid solutions: at high temperatures (-300°K and above), the CRSS is relatively temperature-independent but becomes strongly dependent on temperature at lower testing temperatures. A reasonable picture of solid-solution strengthening for silver-rich solutions at room temperature based on "direct" strengthening mechanisms3 is as follows. Since silver alloys have low stacking-fault energies, extended dislocations are expected and it is possible that Suzuki locking4 makes the major contribution to the room-temperature solute strengthening. This provides essentially temperature-independent strengthening since thermal motions of the dislocation line are not large enough to aid the dislocation in escaping the solute atmosphere extending over the fault width. An estimate of the

Jan 1, 1964

By Arthur F. Taggart

MR. CHAIRMAN: Congratulations! Your four-ring milling show this year was a dandy. It cleared our minds, for a few hours at least, of what Hitler, Hirohito, the New Deal, and the tribe in the Treasury are trying to do to strangle American enterprise. We mustn&apos;t forget this, but it&apos;s a relief to get our thoughts away from it occasionally. GRINDING-There was a further contribution to the excellent work that the Allis-Chalmers laboratory staff has been doing for the grinding fraternity in compiling-and publishing-a carefully quantitative list of comparative resistances of ores and other materials to comminution (T.P. 1579, Bond-Maxson). A diagnostic accuracy of ± 10 per cent was claimed for estimates based on these figures. Are they really that good? How about some of you men in the field writing M&M about it?

Jan 1, 1943

By A. Long, A. Silverman, J. L. Kulp

Garth Crosby has written an excellent geologic description of the deposits surrounding the Gem stocks in the Coeur d&apos;Alene district. The ore deposits in the area of the Gem stocks may hold the key to the age and mineralization history of the entire Coeur d&apos;Alene district. A recent isotopic study10 of the Coeur d&apos;Alene district in this laboratory illustrates that a classical geologic interpretation of these deposits, with its implications for the whole district, may lead to erroneous conclusions. For this reason it seems pertinent to submit a summary of these results and an interpretation of the mineralizing history of the Coeur d&apos;Alene districts. Pitchblende from the Sunshine mine has been dated as 1100-1200 million years (m.y.) by Kerr and Kulp,11 and Eckelmann and Kulp.12 This pitchblende is known to predate the major sulphide introduction in the Sunshine mine, but it clearly follows the metamorphism and folding of the Belt Series. Recently, Goldich (personal communication) dated sericite from the Belt rocks as 1200 m.y. by the potassium-argon method. This date establishes a minimum Belt age if the sericite is of metamorphic origin and a maximum age if detrital. The Belt Series, therefore, is not latest Precambrian. Lead isotope ratios of galenas have been measured and model ages calculated by Bate, et all3 for the Sunshine mine, Farquhar and Cummingl4 or the Bunker Hill and Sullivan mine, and Cannonl6,18 for a few other deposits in the district. Galenas from similar deposits in Southern British Columbia have been measured by Bate, et al,23 Farquhar and Gumming,11 and Wanless and Leech." The new work in this laboratory includes leads from ten widely scattered mines north and south of the Osburn fault, and through a vertical distance of over 5000 ft (Star mine). Included in this group are the Hercules, Sunset, and Mountain Goat mines, which are adjacent to the Gem stocks. In addition, galenas from stringers which cut the Gem stocks in the Success and Sunrise mines and the Hercules hanging wall dike in the lower western portion of the Hercules mine, were included in the study. All of the above leads, except one, give model ages of 1300-1400 m.y. for the time of segregation from the parent material. The concordance of the common lead and U-Pb ages, the great horizontal and vertical uniformity of the lead ratios, the sulphur ratios of two Sunshine mine galenas and three galenas from the Edith, Page, and Hercules mines indicating average crustal sulphur, and the U23/Pb204 ratio inferred for the original lead environment, indicate that the entire mineralization of the Coeur d&apos;Alene-British Columbia base metal belt was derived from a deep source and emplaced in the Precambrian. One sample of galena from sulphide stringers cutting the North Gem stock at the Sunrise Prospect mine gave a modern (i.e., Tertiary) lead ratio. This mine is located at the northern tip of the stock. The presence of modern lead suggests mobilization of some rock lead during the intrusion of the Gem stocks and their outliers. Larsen et al.l8 have dated the Gem stocks as Tertiary by the lead alpha method. If Coeur d&apos;Alene mineralization was genetically related to Tertiary magma formation and intrusion

Jan 1, 1961