Search Documents

By Frederic Benard

Recovery of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.l During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 166,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature. Equipment Layout and type of equipment conforms to the requirements of the process as described below. In the selenium section, storage tanks, neutralizing tanks and precipitators are of steel construction, lead-lined and arranged for gravity flow (Fig. 1). The neutralizing tanks are equipped with water-cooled lead coils for controlling solution temperature, agitation being accomplished with compressed air. The precipitators are provided with mechanical agitators, and sulphur dioxide is introduced into the solution through 1/2-in. lead pipes leading from a manifold attached to the cover of the precipitator. Each precipitator has internal cooling coils and an air-jet exhauster to carry off fumes. Neutralized solutions are filtered in a 29-plate wooden filter press using heavy cotton duck as a filter medium, forced feed being maintained by a Welmet centrifugal pump. Dilute solutions are concentrated by evaporation in a vacuum evaporator, constructed of cast hard lead. Heat is supplied by an outside steam chest operating under 15 Ib. steam pressure. The solution is circulated through the steam chest by a pump of antimonial lead at a rate approximating 400 cu. ft. per min. The evaporator is evacuated by a water-jet condenser that creates a vacuum of 26 in. of mercury under normal operating conditions. The capacity of the vessel is 60 cu. ft. and the rate of evaporation 25 cu. ft. per hour.

Jan 1, 1943

By Frederic Benard

Recovery of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.l During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 166,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature. Equipment Layout and type of equipment conforms to the requirements of the process as described below. In the selenium section, storage tanks, neutralizing tanks and precipitators are of steel construction, lead-lined and arranged for gravity flow (Fig. 1). The neutralizing tanks are equipped with water-cooled lead coils for controlling solution temperature, agitation being accomplished with compressed air. The precipitators are provided with mechanical agitators, and sulphur dioxide is introduced into the solution through 1/2-in. lead pipes leading from a manifold attached to the cover of the precipitator. Each precipitator has internal cooling coils and an air-jet exhauster to carry off fumes. Neutralized solutions are filtered in a 29-plate wooden filter press using heavy cotton duck as a filter medium, forced feed being maintained by a Welmet centrifugal pump. Dilute solutions are concentrated by evaporation in a vacuum evaporator, constructed of cast hard lead. Heat is supplied by an outside steam chest operating under 15 Ib. steam pressure. The solution is circulated through the steam chest by a pump of antimonial lead at a rate approximating 400 cu. ft. per min. The evaporator is evacuated by a water-jet condenser that creates a vacuum of 26 in. of mercury under normal operating conditions. The capacity of the vessel is 60 cu. ft. and the rate of evaporation 25 cu. ft. per hour.

Jan 1, 1943

By John E. Lanning

During the last decade, since most smelters have included Cottrell plants as standard equipment for the removal of dust from furnace gases, it has become apparent that smeltermen have had a new problem slowly developing. This problem has manifested itself in accelerated destruction of, or serious injury to, the masonry of flues and chimneys. The masonry either spalls, if the material is of low strength, or acquires large major cracks, either of which conditions attains such proportions that renewals or reinforcing become necessary to maintain the structure in satisfactory condition. This paper describes the failure of a large modern brick chimney to such an extent that its safety was vitally impaired; the investigation of its condition; the methods of restoring satisfactory strength to the structure; and the installation of an acidproof lining. Plant History The Clarkdale smelter of the United Verde Copper Co., which was put in operation in 1915, was primarily a blast-furnace plant. The smelter at Jerome had utilized blast furnaces exclusively, and in the design of the new (1915) plant, blast-furnace smelting evidently was considered of major importance, the smelting equipment consisting of four blast furnaces 48 in. by 26 ft. 8 in. and three reverberatories, each 19 by 101 ft. The latter, supplemented by roasters, were intended mainly for handling dust and fine ore resulting from the crushing operations. The original roasting equipment consisted of six six-hearth Wedge roasters, six more being added in 1917. All gases from blast furnaces, reverberatories, roasters and converters were conducted by means of suitable flues and dust chambers to one central chimney. This chimney, 30 ft. inside diameter by 400 ft. high, is a self-supporting steel structure, lined with 4-in. brick supported on steel shelf angles, riveted to the shell, spaced about 15 ft. vertically. The bricks were of local manufacture, not particularly hard-burned, and were laid in ordinary cement-fireclay-sand mortar. No record is available to indicate that any particular effort was made to secure an acidproof mortar. The same materials were employed in the construction of the reverberatory and roaster flues, and the roaster dust chamber. Parenthetically, it may

Jan 1, 1934

By F. Benard

Recovery of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.l During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 165,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature. Equipment Layout and type of equipment conforms to the requirements of the process as described below. In the selenium section, storage tanks, neutralizing tanks and precipitators are of steel construction, lead-lined and arranged for gravity flow (Fig. 1). The neutralizing tanks are equipped with water-cooled lead coils for controlling solution temperature, agitation being accomplished with compressed air. The precipitators are provided with mechanical agitators, and sulphur dioxide is introduced into the solution through 1/2-in. lead pipes leading from a manifold attached to the cover of the precipitator. Each precipitator has internal cooling coils and an air-jet exhauster to carry off fumes. Neutralized solutions are filtered in a 29-plate wooden filter press using heavy cotton duck as a filter medium, forced feed being maintained by a Welmet centrifugal pump. Dilute solutions are concentrated by evaporation in a vacuum evaporator, constructed of cast hard lead. Heat is supplied by an outside steam chest operating under 15 Ib. steam pressure. The solution is circulated through the steam chest by a pump of antimoniallead at a rate approximating 400 cu. ft. per min. The evaporator is evacuated by a water-jet condenser that creates a vacuum of 26 in. of mercury under normal operating conditions. The capacity of the vessel is 60 cu. ft. and the rate of evaporation 25 cu. ft. per hour.

Jan 1, 1944

By S. J. Swainson

PHOSPHATE ROCK is a low- priced commodity. This fact has influenced the choice of mining and beneficiating methods to a greater degree, perhaps, than in most other low-grade mining operations. The fact that many yards of everburden and matrix must be stripped and mined per ton of salable "rock" produced and sold has necessitated he development of relatively simple btneficiating plants having high capacity and low capital and operating costs. The law of diminishing returns must always be reckoned with in phosphate mining and washing, and often recovery must be sacrificed in favor of costs in order to achieve the highest over-all economic efficiency. The phosphate-bearing formation, known as "matrix," is composed of (1) phosphate pebbles, which are somewhat rounded in shape and which vary in size from 1-in, to micron sizes, (2) rounded quartz grains usually smaller than 10 mesh, and (3) clay, of varying "stiffness," which is the binder of the matrix. The phosphate pebbles vary in hardness. Their color, which varies from white to black, is not a reliable indicator of the Bone Phosphate of Lime (B.P.L.) content of the

Jan 1, 1944

By Ernest Burchard

A RECONAISSANCE of the chrome and manganese'1ore deposits of Culm was made in the spring of 191s by Albert Burch representative of the U. S. Bureau of Mines and the writer representing the U. S. Geological Survey. The object of the study was to obtain authentic information for use of the: United States Government as to the location, character, size, and availability of the Cuban deposits of the ores of these important steel-alloy metals. The Cuban Government courteously detailed Sr. E. I. Montoulieu, a mining engineer connected with the Treasury Department, to act as escort and associate throughout the work on the Island. Mr. George A. Wright, of Baracoa, Cuba, a mining engineer especially familiar with the chromite deposits of Oriente Province, was a member of the party from Feb. 25 to Mar. 20. It was possible to visit most of, the chrome-ore deposits that seemed to be of promise, but there was not sufficient time to visit all that were brought to our attention, some of which may have merit. Furthermore, no attempt was made to examine the extensive chromiferous iron-ore deposits of the Mayari, Moa, and Cubitas districts, as these deposits cannot be regarded as sources of chromium except indirectly. At the close of the field work the essential data concerning the quantity and quality of ore probably available for shipment during 1918 and 1919, in the event of the continuation of the European war, and of the tonnage of ore in reserve, were furnished to such Government bureaus as were interested, including the Shipping Board and the War Industries Board, and as soon as chemical analyses of the chrome ores could .be obtained, a press bulletin on the subject was published by the Geological Survey. In the present paper the engineering data, and tonnage estimates contained in the unpublished notes of Mr. Burch have been freely used, and their helpfulness is hereby gratefully acknowledged. Many thanks are due Senor Montoulieu and Mr. Wright for their valuable work in the field; to the officials of the Spanish American Iron Co. and of the various other companies; and to individuals holding chromite claims, for courteously facilitating the work of the party. In the study of material for the present paper, chemical analyses have been made by R. C. Wells and petrographic determinations and descriptions were furnished by Miss E. F. Bliss, both of the U. S. Geological Survey.

Jan 9, 1919

By N. I. Fisher, J. Shepherd

A rapid method of determining natural fracture trends in collieries has been developed. The method will yield information that is precise enough to permit fracture domain boundaries to be delineated in a coal seam. Instead of a survey of cleat trends in a colliery taking several man-weeks or even man-months, a reconnaissance survey can be carried out in only a few man-days. At each of a sequence of sampling sites along a traverse, five measurements of trend are recorded for each set of fracture directions. A sequential plot of the medians of each fracture set is then made manually underground or by a computer in the mine office. Changes in fracture pattern can be detected easily in colliery development work if a geologist visits advancing faces regularly, and forecasts can be made about the likelihood of forthcoming faults and dykes. A full description of this method is given in Shepherd and Fisher (1981). The concept of mapping fractures rapidly in a colliery is based on using a geological traverse (Compton, 1962), along which observations can be made at chosen, regular intervals. The technique has been widely used for surface mapping across outcrops and in follow-up work in photogeological studies (Hepworth and Kennerley, 1970). In these cases, the geologist surveys the traverse line as mapping proceeds. In a colliery, however, ready-made traverse lines already exist in panels and along main roadways, often in several directions. It is thus possible to traverse a colliery in different directions and record the fracture trends at intervals, generating a reconnaissance fracture map. This can also be done on a continuing basis as mine development takes place. Generally, a sampling traverse should be longer than 0.5 km with sampling sites at relatively close-spaced intervals along the traverse. For example, in room-and-pillar mines pillars are commonly formed on 40-m centers and the sampling sites can then be arranged at 20-m intervals [(Fig. 1)]. The sites might have to be closer together for mines known to have bad mining conditions. The predominant fracture trend is normally the face cleat and the subordinate trend is the butt cleat (McCulloch et al.. 1974). Various changes can occur in the cleat or joint pattern: the face and butt sets may disappear or an entirely new set or sets may appear. Therefore, it is best to record all prominent fracture sets. Sometimes there is only one; in other cases there may be as many as three or more. An odd number of measurements of each fracture set are made (generally five or more) to enable the median value to be determined easily. The median value can be plotted underground using graph paper or a computer plot can be made in the laboratory or mine office [(Fig. 2)]. The sequential linked median (SLIME) plot draws the median trend for each sampling site as a unit line segment. The segments from successive sampling sites can be connected together to form a long chain [(Fig. 2A)]. The needle plot, on the other hand, draws a straight line to represent the traverse and then plots out the median trend for each sampling site [(Fig. 2B)]. The SLIME plot is better for visual display, as it highlights small irregularities and gross changes in trend. However, some work is required to relate the individual segments to their site location along a traverse. In this respect, the needle plot is more convenient because each segment -can be plotted-at a point corresponding to its location. Also, there is precise match-up if needle plots of face and butt cleat are compared. A description and listing of the SLIME program is given by White et al. (1981). An example of the use of this method is given for Wallsend Borehole colliery in New South Wales (Australia) [(Fig. 2)], where domains II and IV are associated with mining hazards. Domain II is coincident with a normal fault of 2.6-m throw, and domain IV with a basic dyke 12 m thick. These hazards were approached driving in a southwesterly direction, and a pronounced change in trend of the cleat to a northwesterly direction occurred at a distance of approximately 45 m from each one. The northwestern joint trend is parallel to that of the dyke and fault, and it occurs at a higher frequency close to these structures. The association of a particular joint set with faults has been found elsewhere (Shepherd and Creasey, 1979). The two minor cleat direction changes within domain V are narrow joint zones that are less than 5 m wide. The fracture trends derived from a SLIME traverse can be verified by collecting larger quantities of data at selected sites, as shown in the balloon density (rose) plots depicted in [Fig. 2C]. We are grateful for the financial support provided by Thiess Bros. Pty. Ltd. and the National Energy Research, Development, and Demonstration Program administered by the Commonwealth Department of National Development and Energy. R.W. Miller Holdings Ltd. and Thiess Bros. Pty. Ltd. are thanked for their permission to publish data from their collieries.

Jan 1, 1982

By Oliver Bowles

DELICATE PLANTS are now put to bed for the winter under glass-wool or rock-wool blankets. Thus arise new and unexpected uses for non-metallic materials and rocks and, at the same time, certain unique uses are fading out; for instance, the Italians have taken steps to bar the use of salt for money in Ethiopia. Novel sources of supply find a place in the record of recent achievements as exemplified in the migration of the frontiers of industrial mineral exploitation beyond the land area of the earth to include the ocean. Salt, of course, has been recovered from the sea for years but the treatment of enormous quantities of sea water for bromine has lately added to the importance of the ocean as a reservoir of mineral wealth. Increased use of non-metallic minerals in the commercial and economic life of the country is reflected in the wide scope and activity of the Industrial Minerals Division of the Institute. The outstanding recent achievement of the Division is the publication of a 955-page volume on industrial minerals and rocks, comprising 48 commodity chapters each written by an authority on the subject.

Jan 1, 1938

By Joseph C. McCaskill

The writer assumes that this volume is not intended to serve as a source of statistics on international trade and that the reader is not interested in wading through a lot of statistical tables copied from the various reporting agencies. Generalizations therefore are made whenever possible and not always is the source of the information meticulously cited. The United Nations regularly publishes trade data on mineral commodities. E. J. Gealy, and C. L Kimbell, of the U S Bureau of Mines (USBM), work with these data and estimate that they cover approximately 78% of total mineral commodities traded. In addition the General Agreement on Tariffs and Trade (GATT) publishes analyses of certain trade data The most complete report of production and trade in minerals 1s probably the international volume of the U.S. Bureau of Mines Yearbook The latest available edition is for 1968, and some of the data in this edition cover only as late as 1967. Unless otherwise stated, the source of data used in the chapter is this Yearbook Other staff members of the Bureau were most helpful and cooperative They are not to be held responsible for conclusions or points of view to be found in the chapter. THE NATURE AND SCOPE OF INTERNATIONAL TRADE The two and a half decades since World War II have witnessed an unprecedented growth international commerce The end of the war found the world economy seriously crippled. Many countries had suffered severe war damage; international trade was disrupted and nations had to resort to exchange controls and bilateral trading arrangements. The postwar recovery, however, was remarkably rapid Within two decades, world Income more than doubled, and world trade which was less than $60 billion in 1948 exceeded $200 billion in 1968, 8 and reached $278 billion in 1970.18 The growing world trade contributed to world prosperity which in turn fostered growth of trade. This dramatic growth of international commerce was made possible by the progressive liberalization of trade and capital movements by the major trading nations of the world which began immediately after the War and has not yet completely lost its steam. The modern-day stimulus of the expanded trade movement was the enactment by the Congress of the United States in 1934, of the

Jan 1, 1976

By E. H. Crabtree

This paper traces the experimental and pilot plant work completed by the authors since 1939 including the various methods which have been developed in applying coarse activated carbon to cyanidation. The methods and results developed by the authors in desorbing gold and silver from carbons are given and the possibilities for the re-use of the desorbed carbons are discussed

Jan 1, 1950

Jan 1, 1970

By G. R. Speich, L. Zwell, H. A. Wriedt

HORNBOGEN1 has recently shown that it is possible to measure the degree of segregation accompanying cellular precipitation in ferritic Fe-Zn alloys by measuring the lattice parameter of the ferrite phase within the cell. In extending this work to study a wider range of composition and to evaluate the free-energy change accompanying the growth of the cells, the lattice parameter and the boundary of the a! phase in Fe-Zn alloys were redetermined to check the earlier work of Schramm.2 This appeared to be necessary since the Fe-Zn diagram has been drastically revised since the work of Schramm. Stadelmaier and Bridgers3 have recently shown that, contrary to prior belief: the y iron field is closed and the a phase boundary extends to an a + T + L peritectic at 782°C where peritectic a contains 42 at, pet Zn. The phase T in equilibrium with the a solid solution has a composition near Fe3Zn10 and a cubic 081 type structure.' The alloys were prepared by two different methods. In the first method carbonyl iron powder (400 mesh, 99.8 pet pure) and high-purity zinc powder (200 mesh, 99.99 pet pure) were mixed in a ball mill and then pressed in a die at 40,000 psi pressure to make compacts with a diameter of 5/8 in. and a thickness of l/4 in. These were sealed in evacuated quartz capsules, gradually heated to 1100°C over a period of 1 week (3 days at 600°C) 3 days at 800°C, 1 day at (1100°C), and then quenched in iced brine. For the alloys containing 23.4 and 30.1 at. pet Zn, the final homogenization anneals were performed at 1000" and 850°C) respectively, to prevent melting. In the second method, alloys were prepared by saturating high-purity iron millings (0.001 in. thick, 99.9 pet pure) in zinc vapor. For each alloy the impregnation was conducted at a fixed vapor pressure of zinc and a fixed temperature between 750' and 800°C. When saturated, the millings were quenched in water. The compositions of the alloys prepared by both methods are shown in Table I. The lattice parameters of the ferritic solid solutions were determined by comparing the 26 values of their 310, peaks (using Co Ka) or of their 211 , peaks (using Cr Ka) with those of corresponding peaks for high-purity a iron. The 20 values were measured at room temperature with an X-ray dif-fractometer (G.E.-XRD5). By using a fiducial value of 2.8664Å for the lattice parameter of pure a iron at 25oC,5 the lattice parameters of the zinc-bearing

Jan 1, 1964

By Donald F. Hammer, Donald W. Peterson

The Magma mine at Superior, Arizona, has produced over 13 million tons of ore yielding 1.5 billion pounds of copper. It is a mesathermal deposit, and, although the bulk of the ore has come from the Magma vein, most of the recent production has come from replacement deposits in limestone. The mine lies in a Precambrian and Paleozoic sequence of rocks that includes schist, diabase, quartzite, shale, and limestone; nearby, these rocks are intruded by igneous bodies of Mesozoic age that were probably the source of the ore-bearing fluids. Locally, these rocks are overlain by Cenozoic volcanic rocks and conglomerate. Layered rocks at the mine dip eastward about 30°. The area is extensively faulted, and surface faults are grouped into an earlier east-trending set and a later northtrending set. An additional set of diagonal faults that trends northwest and northeast is recognized underground. The east-trending Magma vein-fault, with its splits and branches, is the principal mineralized structure of the district. The bulk of the ore occurs in large ore shoots that plunge steeply westward and are sporadically connected by irregular ore shoots dipping gently eastward. The main ore controls apparently are selective zones of permeability related to the transverse faults. A bed of crystalline limestone near the base of the Martin Limestone (Devonian) is the host for the replacement ore bodies-discontinuous tabular pods dipping eastward parallel to the bedding. Selective permeability is again the apparent ore control, caused both by local hydrothermal solution of limestone and by deformation along faults. The principal copper minerals in the vein are chalcopyrite, bornite, enargite, tennantite, chalcocite, and digenite; these minerals vary in abundance according to a distinct zoning pattern. The upper part of the mine yielded considerable zinc as sphalerite, and the oxidized zone was rich in silver. The chief gangue minerals are pyrite, quartz, and hematite. In the limestone replacement bodies, chalcopyrite and bornite are the chief ore minerals.

Jan 1, 1968

By Chas Fettke

DURING the summer of 1916, while on a visit to the United States Agricultural Experiment Station at Mayaguez, Porto Rico, the writers were told by D. W. May, the director, that an occurrence of manganese ore had been reported from the mesa southeast of Mayaguez. A visit to the locality showed that the mesa is covered by a mantle of bright red soil resting upon serpentine. Here and there over its surface concretionary masses of limonite have been washed out of this soil. These were FIG. I.-MAYAGUEZ FROM NORTHWEST END OF MESA. apparently mistaken for manganese ore. On account of the similarity of this occurrence to the extensive iron deposits of northeastern Cuba, it was thought that a brief description based upon a two days' reconnaissance survey of the area would be of scientific interest. Mayaguez is on the west coast of Porto Rico, at Mayaguez Bay, which is the third in importance of the harbors of the island. The city itself is about ¾ mile inland on the low-lying plain at the mouth of the

Jan 3, 1918

Idaho Bureau of Mines and Geology, University of Idaho, Moscow, Ida. John W. Finch, Director. A list of publications will be sent upon application. A series of Bulletins and Pamphlets have been issued by the Bureau to date since 1920 Of the Bulletins, six are out of print, and a charge is made for eight. Each of the Bulletins, in the main, treats of the geology and resources of a particular district in Idaho, as follows (only available Bulletins listed): Bulletin 1, South central Idaho (1920), 15 cents, 7, North central Idaho (1924), 50 cents, 8, Bonneville, Bingham and Caribou counties (1924), 50 cents, 9, Boise Basin (1924), 50 cents; 10, Boundary County (1926), 50 cents; 11, Region about Silver City (1926), 50 cents; 12, Clark Fork district (1930), 50 cents, 14, Eastern Cassia County (1931), 50 cents, Press Bulletin 15, Teton County (1927), Bulletin 16, Melon Valley near Buhl (1927); 17, Concerning land slips near Whitebird, Idaho (1928) The 37 Pamphlets are issued free of cost, and each treats, also, in the main of the geology and resources of a particular district in Idaho Nos 1, 2, 3, 4, 5, 7, 8, 10, 17, 18, 20, 22, 25, 26, 30 and 35 are out of print Of those available, attention may be called to Pamphlet 6, Reported platinum occurrences near Coeur d' Alene (1925), 11, Bruneau River Basin, 12, Power and Oneida

Jan 1, 1933

By John T. Crawford

Introduction Loading and hauling systems are evaluated in open pit mining for new properties, expanding existing operations, changing systems or equipment, and equipment replacement analysis. The objective of such evaluations is to determine the equipment needed to handle planned tonnages at the lowest cash flow cost. Cash flow costs are used to combine capital outlays with operating and maintenance costs. Leasing costs could be substituted for capital costs with appropriate modifications to calculation procedures. These modifications will not be covered. This chapter will describe methods of evaluating loading and hauling systems, concentrating on some of the more often raised questions concerning quantitative data. While the methods described are not the only ones in current use, they have a record of proven reliability. The shovel and haulage truck system is used In the examples because of its common use in open pit mines. In medium to large open pit mines, electric shovels and diesel-electric drive haulage trucks are normally used. The basic ideas presented in this chapter apply to all loading and hauling systems, with appropriate modifications. The process of performing a shovel and haulage truck evaluation can be time-consuming and tedious because of the quantity of data involved, but it is not particularly difficult. The examples used to Illustrate shovel and haulage truck evaluation are based on a hypothetical open pit mine operating 350 days per year producing 31 750- 000 t (35,000,000 st, 100,000 stpd) annually, of which 11 110 000 t ( 12,250,000 st, 35,000 stpd) are ore. Selection of the optimum shovel and haulage truck fleets will be shown. The principal sources of data for the examples or any other equipment evaluation are equipment manufacturers and actual operations. Whenever possible, actual operating experience should be used to verify estimates. The quantitative data presented herein are unrelated to a specific existing mining operation.

Jan 1, 1979

By T. B. Nolan, R. N. Hunt

In terms of present metal prices, analysis of extant records of the Eureka district indicate past production of the magnitude of $200,000,000 in recovered silver, lead, and gold. Production to date has been thoroughly oxidized ore from massive replacements, fissures, manta, and pipe-like bodies-in large part from the massive Eldorado (middle Cambrian) and Hamburg (middle to late Cambrian) dolomite horizons. In the productive area of about 6 square miles carbonate rocks comprise 80 per cent of the section, which includes early Cambrian to late Ordovician horizons. Four-fifths or more of the district's production came from a block of Eldorado dolomite in Ruby Hill that was moved in over younger horizons on strands of a regional thrust fault. The lower 500 to 600 feet of the block was much fractured and brecciated and became host to the ores. The Ruby Hill fault, a late normal fault, limits the Ruby Hill block of dolomite on the north for its entire length of nearly a mile and terminates the downward extent and exploitation of its ores. It introduced an hiatus of some 40 years in the district's development. Drilling of the past 20-odd years, followed by underground work, has now exposed the down-faulted extension of the Ruby Hill block of Eldorado dolomite and its contained ores, dropped 1800 feet in a dip shift to depths beneath the surface of 2000 to 3000 feet. The ores at depth are the sulfide counterpart of those mined in early years on the footwall side of the fault. The ores of the district may be attributed to the same source as the intrusive quartz diorite outcropping in a limited way south of Ruby Hill but found at depth elsewhere in drill holes. The long north-south axis of the district, its anticlinal structure, its major faults, and the distribution of the intrusives and, in their relation to the surface, the ores themselves, all suggest that erosion has not cut deep enough to expose the extent of intrusives and the ores consequent upon them.

Jan 1, 1968

By A. B. Kinzel

ALTHOUGH the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approxi-mately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cementite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consider-ation of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:1 C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown in Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850° C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the

Jan 1, 1934

By David C. Jonson, W. Bruce MacKenzie, Arthur A. Bookstrom, Vaughn E. Surface, Neil K. Muncaster, Stewart R. Wallace

In mid-Tertiary time a wet silici-alkalic magma penetrated the Precambrian rocks of what is now the Tenmile Range of Central Colorado and formed the Climax Stock. The stock is a composite one and was intruded in four separate irruptions, each giving rise to a major hydrothermal event. The first three of these produced large stockwork ore bodies that cap and flank the tops of their respective source intrusives; the fourth, and last, yielded almost no commercial mineralization. The ore bodies and their related zones of alteration are circular to ring-shaped in plan and arcuate in section. The different phases of the stock are so positioned with respect to each other that many of the circular and arcuate zones of mineralization and alteration overlap or are juxtaposed. Evidence of a time separation between the different ore bodies is found in certain dikes that were intruded between periods of mineralization and are well mineralized in one ore body but are barren in another. If it is assumed that the parent magma at Climax contained 10 per cent "water," that the "water" contained 0.1 grams per liter of molybdenum, and that the processes of extraction were 100 per cent efficient, then approximately 10 cubic miles of magma would be required for the formation of each ore body. The volume requirements, taken in conjunction with the cross-sectional areas of the different phases of the stock to explored depths, suggest to the authors that each magma chamber was columnar, extended to a depth of thousands of feet, and was connected with a much larger master reservoir. The repetition of similar intrusive, structural, and hydrothermal events, indicates periodic tapping of this reservoir. A regular chemical evolution of the parent magma is suggested by the systematic change in metal ratios and differences in the sites of deposition, relative to the source intrusive, in each of the four separate igneous hydrothermal stages. The preparation of ground was due to changes in magmatic and/ or hydrothermal pressures within the igneous-hydrothermal columns; small, repeated, up and down movements of the rock enclosing the tops of the columns formed the stockwork fractures into which the mineralizers penetrated. The forceful emplacement of each successive phase of the Climax Stock resulted in a slight doming and rotation to the westward of the earlier-formed geologic features. Postore normal displacement along the Mosquito fault is estimated at about 9000 feet. Part of one ore body was cut by the fault and lies at depth below the Paleozoic sedimentary strata on the hanging wall. On the footwall side of the fault, subaerial erosion and glaciation removed a large part of one ore body and uncovered the top of a second.

Jan 1, 1968

By R. V. Norris

The anthracite coal trade, with a shipment averaging about 70,000,000 tons per year, differs essentially from other coal business, iii the fact that the larger sizes, comprising about 65 per cent. of the total, are used almost exclusively for domestic purposes, principally during the winter months; and that for proper combustion close-sizing is imperative, so that eight sizes are made; broken, egg, stove, and nut, known as prepared sizes, and pea, buckwheat, rice, and barley, known as steam sizes. These sizes are made in the regular course of preparation, and but little variation in the natural percentage of each is practicable. Thus it is necessary either to work the collieries intermittently, or to dispose of all the varying sizes in their fixed proportions. Unfortunately, the market does not at all times absorb the coal in proper proportions, and rather than interfere with the regular operation of the mines it has been found economical to provide storage for the excess. While the cellars of' the consumers are the great storage-plants of the country, this capacity is not under the control of the trade, except so far as reduced prices during the spring and summer months may tempt the use of this reserve. The same remark applies but with less force to the retail yards, which, though usually small, store in the aggregate a large amount of anthracite. While every effort is made to utilize to the utmost the individual storage-capacity of the country, there still remains the necessity for taking care of the irregularities of the market by the construction of storage-plants under the direct control of the producers. Such plants are usually the property of the railroads, and are situated at points most convenient from a traffic stand-point.

Jan 1, 1912