Search Documents

By L. H. DeWald

During the examination of various commercial brands of copper wire bars, which had exhibited different degrees of adaptability for being drawn into fine gages of wire by the present-day high speed machine, it was found that each brand had a more or less characteristic crystal macrostructure. The extremes of these macrostructures are similar FIG. 1.-EFFECT OF METAL TEMPERATURE IN CASTING ON CRYSTAL MACROSTRUCTURE OF BAR. Reading from left to right, metal temperatures were 1166" C., 1149" C., 1132" C.. 1121" C., 1093" C. to the maximum variation shown in the photomacrographs reproduced in Fig. 1. As the various brands did not differ materially in chemical composition, it was concluded that the differences in structure were the result of variations in casting technique.

Jan 1, 1931

By R. S. Sanford

The Claim Point chromite deposits are at tidewater near the southern tip of the Kenai Peninsula in southwestern Alaska, The United States Geological Survey had a field party in the region from July until September 1940 under P. W. Guild, assistant geologist; maps and geological data were assembled and made available to the Bureau of Mines. A preliminary investigation of the deposits at Claim Point by the senior author during July 1941 was followed by surface sampling and core drilling to determine the quantity and grade of the ere, The Geological Survey was represented at the project by George O. Gates, geologist. Cores were checked and the structural data revealed by drill cores were interpreted. The principal chromite deposits have been sampled and delimitated by trenching and core drilling. Other deposits were trenched and sampled but were too small or too low-grade to warrant core drilling.

Jan 1, 1949

By M. E. Gershon

Conventional methods of drill hole site selection are reviewed briefly. Two approaches using geostatistics are then discussed, both of which have been shown to yield improved results. Finally, a branch and bound algorithm is described which will select the best locations for drilling from a user specified number of possible drill sites. Two options are discussed. First, the user can specify a maximum drilling investment or a maximum number of drill holes and the program will select the locations yielding the minimum estimation variance. This amounts to getting the most for a given investment. Alternatively, a maximum tolerable estimation variance can be specified and the program will select the number and location of the drill holes to obtain the desired information at a minimum cost. Another benefit of the approach is the quantification of the tradeoffs between investment and information obtained.

Jan 1, 1985

Productivity in underground metal and nonmetal mines is contingent upon work methods, mine layout, and ore handling techniques. One of the most important factors impacting productivity is the efficient movement of men, materials and supplies from the surface into and throughout the mine. Various transportation systems such as man-trains, service shafts, rubber-tired diesel equipment, etc. are currently used to transport men and supplies in underground mines. In many underground mines, it is not uncommon for a worker to spend 25% of his eight-hour working day traveling from the surface to his work area and returning to the surface.

Jan 1, 1975

By R. C. Bryce

"Selbaie is located northwest of Joutel, in what is known as the fourth east-west volcanic sediment group in northwestern Quebec. The main metals produced are copper and zinc, with important contents of both silver and gold. Production comes from an open pit mine on the A-I zone and from two underground mines on the B zone and the A-2 zone. Each mine gave rise to important capital investment programs for construction and mine development, all of which were managed and staffed with company-hired, non-union personnel. Production from all sources now exceeds 7000 tonnes per day, with a workforce of540 regular employees. Of particular interest technically is the high recovery of B zone reserves underneath 40 m of overburden cover, the low-cost capital development of the A-2 zone, the computerized control of open pit mining, and the successful copper-zinc separation of the A-1 zone ore. Due to the low grades of the mineral deposits, efficiency in all aspects of the production process, is essential to the success of the operation.LocationThe Selbaie Mine is located 82 km northwest of the locality of Joutel in northwestern Quebec (Fig. 1). Access to the mine is by an all-weather road, 32 km of which is paved. A second road access to the site is via La Sarre, 134km to the southwest. Employee access, materials transport and haulage of copper and zinc concentrates take place over both of these roads."

Jan 1, 1990

By Youze Xu

The leaching and reduction of Cr(VI) in soils contaminated by chromium-containing slag were investigated with column experiments. The results showed that Cr(VI) concentration in leachate decreased from 988 mg L-1 to 407 mg L-1 after 7 days when water was used as leaching agent. However, Cr(VI) in leachate in culture medium treatment was not detected at above periods. In comparison, Cr(VI) concentration in leachate from autoclaved soil remained 398 mg L-1 at the end of experiment. The results indicated that the indigenous microorganism was capable of reducing Cr(VI). The amount of Cr(VI) reduction was 335 mg at the whole experiment period and the reduction rate was 67.09 mg d-1. Carbon supply showed minor effect on Cr(VI) reduction. However the reduction capability of Cr(VI) could be improved by combination of the carbon and the nitrogen. The optimal quantity was 5 g L-1 of yeast extract and 4 g L-1 of glucose.

Jan 1, 2009

This paper presents a study about reopening of a quarry near to the geothermal region of Kntahya, Turkey. The production method was gallery blasting which resulted in very high ground vibrations. Therefore the quarry had been closed down by the local authorities about 12 years ago due to possible damages to the geothermal resources. In order to reopen the quarry, reserve estimation and production planning studies needs to be carried out as well as applying environmentally sensitive production method. The result of reserve estimation studies showed approximately 12.5 Mt reserve in the area. The market studies indicated that annual production of 600 000 tonnes could be sold. These results justify to reopen the quarry. In order to overcome environmental problems, bench blasting production method instead of gallery blasting has been planned. This method enables to design a drilling blasting pattern that will almost result in no ground vibrations.

Dec 6, 2010

By Victor Erickson

ECONOMIC recovery, which began in 1958, carried through into 1959 but was somewhat retarded by the 116-day steel strike beginning in July 1959. Recovery and economic growth increased production and consumption of mineral fuels 3 percent above 1958. The increase was accomplished despite a drop of 26 percent in coal exports. Prices remained constant during the year so that the value of production and consumption also increased 3 percent over 1958. Stocks in the hands of producers at yearend were little changed from the supply at the beginning of the year. Employment in the field of mineral fuels decreased 6.4 percent from 1958. Average hourly earnings were up 7 percent, and average hours worked were up 5 percent, with the result that weekly earnings gained 11.8 percent. Internal freight rates were relatively constant, but ocean tanker rates declined both in 1958 and 1959 from the high rates charged during the Suez crisis. The index of major input expenses decreased for anthracite, held constant for bituminous coal, and increased for petroleum. The index of labor cost per dollar of product and per ton of product declined again in 1959 to a new low in anthracite and bituminous-coal mining industries.

Jan 1, 1960

By H. L. Riley

Cleaning and handling of fine coal are generally conceded to be more difficult problems than preparation of the coarser sizes. Increased mechanization in the coal-mining industry has, in general, resulted in an increased percentage of the fine sizes in the total coal mined. If the coal fines are cleaned by wet methods, the minus-1/16-inch square-mesh particles cause most of the sludge and slurry problems encountered in preparing wet coal. Equipment that separates coal from refuse on the basis of specific gravity is not efficient on sizes that, because of their fineness, do not follow the same laws of hindered settling as the larger particles. Probably the best solution of fine-coal cleaning problems is to use other methods, such as flotation, that utilize other physical characteristics than those determining hindered-settling ratios. Regarding the type of flotation known as the Elmore vacuum-flotation process there has been a scarcity of data and information available in this country. An investigation has therefore been made to obtain additional date and information on this process under laboratory conditions. During this investigation an effort has been made to evaluate the relative efficiencies of vacuum and mechanical laboratory froth flotation cells. The investigation included float-and-sink, screen-sizing, and flotation tests on 2 different samples of 14-mesh to 0 raw coal and an a sample of slurry from the settling-tank overflow of a typical washer. One raw-coal sample was obtained from the American bed and represented a type of coal that is relatively easy to clean. The other raw-coal sample was from the Mary lee bed and represented a type considered difficult to clean.

Jan 1, 1954

The morphological changes that gold undergoes during transport in gravel-bed rivers are a function of transport distance in particular, as well as bedload material, river gradient and velocity, and bed roughness. Gold size, shape and outline are modified by abrasion, flattening, folding and breakage during transport. The resultant morphological characteristics can be used to predict source types, source location and transport distance, as well as the origin and dispersal patterns of gold in ancient placers where the transport history is unknown.

Jan 1, 1998

By J. C. Edwards, C. C. Hwang

In ventilated tunnel fires, smoke and hot combustion products may form a layer near the ceiling and flow in the direction opposite to the ventilation stream. The existence of this reverse stratified flow has an important bearing on fire fighting and evacuation of underground mine roadways, tunnels and building corridors. In the present study, conducted by the National Institute for Occupational Safety and Health, a CFD program (fire dynamics simulator) based on large eddy simulations (LES) is used to model floor-level fires in a ventilated tunnel. Specifically, the critical ventilation velocity that is just sufficient to prevent the formation of a reverse stratified layer is simulated for two tunnels of different size. The computer code is verified by checking the computed velocity profile against experimental measurements. The CFD results show the leveling-off of the critical ventilation velocity as the heat release rate surpasses a certain value. At this critical ventilation, the ceiling temperature above the fire reaches a maximum for both tunnels. The velocity leveling-off can be explained from this observation. An extended correlation of Newman (Combust. Flame 57 (1984) 33) is applied to the temperature profiles obtained by CFD. At the critical ventilation, temperature stratification exists downstream from the fire. The computed critical ventilation velocity shows fair agreement with available experimental data taken from both horizontal and inclined fire tunnels. The CFD simulations indicate that the Froude modeling is an approximation for tunnel fires. The Froude-scaling law does not apply to two geometrically similar fire tunnels. The CFD results are compared with two simple theories of critical ventilation by Kennedy et al. (ASHRAE Trans. Res. 102(2) (1996) 40) and Kunsch

By Shenxu Bao, Ying Bian, Xiang Liu, Liuyi Ren, Yimin Zhang, Chun Liu

Efficient enrichment of high-carbon low-grade mica stone coal containing vanadium is a key problem in the mineral processing field, and the mature beneficiation process is yet to be developed and applied. In this paper, a special mineral mica type of stone coal containing vanadium from Tongshan, Hubei Province, China was selected as the research object. Chemical analysis results show that this mineral contains V2O5 0.71%, SiO2 49.28%, C 13.44%, and CaO 6.26%. Scanning electron microscope (SEM) shows that vanadium generally exists in all kinds of mica minerals in 20 µm to 50 µm fractions. Mica stone coal containing vanadium must be ground to a particular fineness (approximately 45 µm). To reduce acid consumption during vanadium extraction from stone coal through acid leaching, a pretreatment process was proposed to enrich micas by using shaking table and flotation methods. A new combined technology process was implemented, resulting in a 0.96% improvement in the vanadium grade of raw materials in the succeeding process. Vanadium losses were controlled to 4.57% through the pre-concentration process, which reduced the burden of the subsequent procedure. The content of high acid consuming minerals was also diminished, such that approximately 6612 CNY was saved from producing 1 t V2O5. Therefore, stone coal containing vanadium should be pre-concentrated by using an appropriate combined process to reduce costs.

Jan 1, 2014

By Laurance L. Oden

The Bureau of Mines is developing nickel catalysts for converting synthesis gas derived from coal to synthetic natural gas. The present report describes the relationship between the composition of aluminum-nickel alloys in the composition range NiAl3 to Ni2Al3 equilibrated at 840° C and the properties of catalysts obtained from them. Methanation activity was determined in the temperature range of 300° to 360° C in a flowing gas stream containing 1 pct CO, 8 pct H2, and the remainder He. One part per million of H2S was added to the gas stream at 400° C to evaluate the susceptibility of catalysts to sulfur poisoning. The total surface area was measured by the adsorption of nitrogen at liquid nitrogen temperature, and the active surface area was measured by the adsorption of hydrogen at room temperature. Total surface area and active surface area were found to increase with increasing proportion of aluminum-saturated Ni2Al3 in the precursor alloy, but methanation activity and resistance to poisoning by H2S were nearly constant. However, the methanation activity of the catalyst prepared from stoichiometric Ni2Al3 was less than half that of the other catalysts.

Jan 1, 1978

By E. Snyders

The upgrading process of an inferior grade of zircon to a superior opacifier for ceramic applications was investigated. A calcining process in the presence of mineralizers was used to produce the product in a conventional muffle furnace. A pre-milled inferior grade zircon concentrate, with a relatively high iron and alumina content generally not suitable for high quality ceramic applications, was used in this study. The influence of the upgrading process on the opacifying properties of the zircon material was compared to that of commercially available prime grade zircon opacifier products currently being produced in South Africa. The influence of a calcining step in the presence of mineralizers with regard to the milling characteristics of the treated zircon material was also evaluated in this study. The morphology of the treated and untreated zircon opacifier samples were investigated by SEM micrographs and the colours of zircon samples were characterized on the grounds of the Commission Internationale de l`Eclairage (CIE) standard procedure (CIE L* a* b* measurements) after application on a bisque ceramic tile. It was found that the treatment improved both the milling as well as the opacifying properties of the treated inferior grade zircon concentrate and renders it equivalent to or better than prime grade zircon opacacifiers currently produced. Keywords: ZrSiO4; opacifier; colour; milling; calcining.

Jan 1, 2005

By E. Fernandez

HIGH SPEED RAILWAY NETWORK Spain is a very adequate country to develop the high speed railway network thank to its geographical feature which has a 600km long radius, from Madrid- the capital that covers mostly the whole country. Therefore, the railway is a major competitor of the airline. In Spain, the new access to the north and northwest is nowadays the most important railway project which will allow a significant saving of time in the near future to the central plateau and the northern territories. Time savings as well as strict environmental considerations have been the main objective of various studies during the last decade leading to Guadarrama and Pajares tunnels as ones of the optimum solutions. Cordoba-Malaga high speed railway, the extension of the present Madrid—Sevilleline, through the Abdalajis range and the rail project to cross oriental Pyrenees between Spain and France are another two samples of large tunnels currently underway. In these four projects, the ground already encountered and to be soon encountered is highly variable, from very hard granite and gneiss in Guadarrama and Pertus to very poor argillite in Abdalajis, shale in Pajares and schist in Pertus. A number of faults are also expected. Hence, double shield hard rock TBM has been chosen. Figure 1 shows a general scheme in four projects. These four projects represent a total of 2 × 68 km of which 87 km are under DRAGADOS contracts. PROJECTS UNDERTAKEN BY DRAGADOS Guadarrama Tunnels This project is the longest twin tunnel with 28.377km, in Spain and considered one of the longest in Europe. The operating speed will be 300 km/h. This tunnel will link Madrid and the north territories through Guadarrama range. (Figure 2). The south portal is placed at el. 997.8m above the sea level. The tunnel starts with an inclination of 3‰, increasing until 15‰. After 6,620m length, the tunnel passes under the Morcuera ridge with an overburden of 960m. After 13,400m length, the elevation is 1,024m which is the highest point, and then the tunnel declines with a slope of 9.5‰, 2‰ and 19‰ until the north portal in Segovia province. At the border of Madrid and Segovia that is Penalara peak, the maximum

Jan 1, 2005

By F. W. Lee

This paper purposes to outline briefly results of seismic measurements made in the vicinity of blasts in a mine and in open-quarry operations. It endeavors to examine the amplitude and frequency of such vibrations as influenced by the loading, geology, and distance from the source and includes comments on factors that may index the destructiveness of a vibration and a method for measuring the stresses produced. There seems to be no simple mathematical analysis of the transmission of seismic energy through the ground, and experimental observations are at present most feasible. SEISMOLOGIC INSTRUMENTS Instruments developed by the Bureau of Mines for recording ground vibrations from quarry blasting comprise a new type of seismometer, oscillators, and a recording oscillograph. The seismometers respond to vibrations reaching them through the earth and transmit their characteristics by electric current to the oscillograph, where they are recorded by a beam of light on a moving strip of sensitized photographic paper. The seismometers are so constructed that their sensitivity to earth vibration can be controlled, thus keeping the amplitude of the recorded wave within bounds on the paper. Each instrument has been calibrated against vibrations of known intensity and frequency so that correction factors are known for the idiosyncracies of each unit. Moreover, each seismometer is calibrated in the field for its particular sensitivity setting at each blast. By these controls the actual movement of the earth due to vibrations of one ten-thousandth of an inch can be accurately measured.

Jan 1, 1936

By J. Douglas Causey

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 9,600 acres of the 12,350-acre Antelope Creek Wilderness Study Area (MT-065-266) in order to evaluate its mineral resources. Within this report, these 9,600 acres are referred to as the study area. The Antelope Creek Wilderness Study Area, Phillips County, MT, adjoins the north end of the Charles M. Russell Wildlife Refuge. Considered part of the Missouri River Breaks, the area straddles the edge of a thrust fault zone that has deformed the Mesozoic strata in the west half of the area. Shale, siltstone, and sandstone of Cretaceous Age are exposed in the area. Coal beds averaging 3.0 ft thick occur in the Judith River Formation. About 0.20 million short tons of coal were mined from the Judith River Formation adjacent to the west boundary of the area; no production is known in the study area.

Jan 1, 1986

By Bernard Hertlein

¦ Drilled shafts resist scour seismic loads better than groups of driven piles ¦ Drilled shaft construction creates less noise and vibration than driving piles ¦ Drilled shafts permit direct observation of bearing stratum, and confirmation of location ¦ Drilled shafts are cost effective

Jan 1, 2001

By J. E. Harris

By elimination of other possible nucleation processes, it has been demonstrated, for commercially pure magnesium and a Mg-Al alloy, that at stresses less than that necessary for triple-point cracking creep cavities are most probably nucleated heterogeneously at second-phase particles. Evidence for the existence of such particles is presented and the role of grain boundary sliding in the nucleation process is examined quantitatively. DURING creep deformation of polycrystalline magnesium and its dilute alloys in the temperature range 0.45 to 0.7 Tm (Tm = absolute melting temperature) cavities form mainly along grain boundaries oriented normal to the stress axis and failure eventually occurs by their growth and impingement.' The possibility of low-ductility creep failure of magnesium-alloy reactor cans during service has prompted a number of studies of cavity formation in these materials.2-5 In this paper divergent theories of cavity nucleation6-10 are examined critically and conclusions drawn regarding the most probable mechanism of formation of cavities in magnesium. The paper is divided into two parts. The first section consists of the review and quantitative assessment of the possible role of grain boundary sliding in the nucleation process. In the second part an experimental program is described where an electron-microscope technique has been used to determine if second-phase particles exist in as-received commercially pure magnesium and in a magnesium alloy 1) THEORETICAL REVIEW Possible nucleation sites for creep cavities are: a) high-angle grain boundary triple points,11-14 b) subboundary/grain boundary intersections,15-18 c) ledges in the grain boundary, 19-25 d) second-phase particles. 9,26-30 Each of these possibilities is now considered with special reference to deformation of magnesium. 1.1) Triple-Point Cracking. The stroh31 condition to nucleate fracture is: " > vr [1] where ss = applied shear stress, ? = surface energy, C = shear modulus, L = length of sliding interface. This relationship is independent of the nature of the interface and it is possible to calculate the stress concentration at the end of a sliding high-angle grain boundary and thus deduce, approximately,* the minimum applied stress necessary to nucleate triple-point cracking. Such theoretical predictions for Nimonic alloys have been made by McLean13 and found to agree quite closely with the minimum stress determined by experiment. Stresses capable of nucleating triple-point cracking should also be sufficient to nucleate fracture at a grain boundary due to intragranular slip, for the lengths of sliding interface in the two cases are approximately equal. Thus the minimum stress for triple-point cracking should represent a demarcation between failure due to general "cracking" and that due to cavitation. Hauser, Landon, and Dorn32 have demonstrated that for polycrystalline magnesium in the temperature range 78° to 298°K the fracture stress is inversely proportional to the square root of the mean grain diameter. As pointed out by stroh31 this result indicates that Eq. [I] describes the fracture characteristics of magnesium at low temperatures. Heal3 has reported that for rapid deformation (112 pct hr-1) of polycrystalline magnesium the transition from cracking to cavitation occurs in the temperature range 175" to 275°C. He also presented the fracture-stress values for the same material tested under similar conditions. From Eq. [I] taking G = 1.3 x 10" dynes , ? = 600 ergs . cm-2,33 and L = 0.017 cm, a Stroh-McLean13,31 tensile stress of -266 kg. cm-2 is calculated, corresponding to a transition temperature of -190°C; this is in

Jan 1, 1965

By S. Ralph Austin

Emanation coefficients of 950 samples of domestic uranium ore were successfully and rapidly determined with fair precision by modifications of the closed-can, gamma-only assay method, using commercially available or similar equipment. Coefficients range from <1 to 91 percent. Emanation varies considerably within each mine and area, but distinct differences among major mining areas were found, ranging from 7.5 percent for Moss Back Member, Chinle Formation, Southwest Lisbon Valley, Utah, to 56.6 percent for Ft. Union Formation (?), Powder River Basin, Wyoming. Coefficients also vary with (1) uranium mineralogy; (2) radium mineralogy; (3) lithology of host rocks; (4) grain size of uranium and radium minerals; (5) comminution of ore; (6) estimated porosity and permeability; (7) moisture content; (8) ore grade; (9) supposed mobility of deposits; age of deposits is unknown but limited by (10) age of host rocks which shows only doubtful correlation with emanation. Data obtained may be used to evaluate effects of investigated parameters on radon concentration in mines and thus to select efficient control measures. Drill-core emanation data allow estimates of probable radon problems in undeveloped deposits.

Jan 1, 1978