Search Documents

By F. M. C. C. Vieira

There are many uncertainties that a mine designer should consider when selecting an optimal layout. Even though the inherent variability in the design parameters indicates that single-values are not representative of mining conditions, risk estimators such as ERR are often used without considering their statistical distributions. A probabilistic methodology has been developed to assess the influence of the extraction sequence and layout geometry on the rockburst risk associated with four ultra-deep mining layouts. The statistical distributions of incremental energy release rates and excess shear stresses at face elements are used as indirect estimators of rockburst risk in stopes, and the statistical distribution of the rock condition factor (RCF) is used as an indirect estimator of rockburst risk in tunnels and service excavations.

Jan 1, 2002

By Mark Sheppard

The technical literature on the general subject of crushing contains many references to the work of investigators on the laws governing, and the factors entering into, the economical production of fine materials. In fine grinding, whether for the purpose of producing fine material, or for the unlocking of minerals in an ore, close control of the screen sizes of primary-crusher products is of secondary consideration and accordingly has received very little attention. The growth and development of the nonmetallic industries, however, have drawn more attention to primary crushing. Many of these industries are interested in the production of relatively coarse products that meet certain definite size specifications, a condition entirely different from that existing in the field of ore dressing. Under such conditions, a knowledge of the factors governing the selection and operation of primary-crushing equipment is essential to the economical production of a satisfactory material.

Jan 1, 1939

By P. Varona, L. Lorig, M. Board, E. Chacon

Geomechanical factors at the mine are important and will become even more relevant as the pit expands and deepens. To address these demands a team was assembled to collect geomechanical information and perform numerical analysis. The west wall is the largest and flattest of all the design sectors in the pit and rigorous studies were carried out on this wall. The wall behaviour is controlled mainly by a set of steeply dipping joints within the slope in the Fortuna Granodiorite and a weak zone, the Zona Plastica, that extends vertically near the pit bottom. These features lead to large toppling displacements in the upper portions of the wall. Two numerical models were used to reproduce the general features of failure observed in the wall. The modelling indicated that a toppling mode of failure results from shear on the steeply dipping joints. The toppling leads to slumping or landslides whereby the west wall flows slowly downslope as the Zona Plastica compresses

Apr 1, 1996

By G. L. Oldright, J. D. Sullivan, W. E. Keck

"An apparatus and procedure developed in the laboratory of the South-west Experiment Station of the Bureau of Mines are capable not only of determining the rate and volume of penetration of solutions into porous materials but also of determining the total volume of voids within particles of porous material, and the density. The method is applicable to ores, bricks, concretes, tiles, filter bottoms, or other porous materials of this nature. As will be made clear in the descriptive matter to follow, the method measures (a) the volume of voids within the porous materials and is not concerned with the interstitial space between the particles.Porous materials usually contain some large voids and also pores that are capillary in nature. To measure the total volume of voids in a sample it is necessary to replace the gas or gases within the voids with some liquid of known density. The large cavities can be filled quite readily, but under ordinary conditions a long time may be required to fill capillary pores. As many porous materials are of a decomposable nature it is necessary to evacuate the porous materials and then submerge them in a liquid of known density to bring about saturation in a short time. Then by the use of a hydrostatic balance the volume of porous material (solid itself) can be determined. To determine the volume of porous material plus voids it is necessary to coat the sample with some material, such s paraffin, which will prevent solution from entering the voids; then, by means of a hydrostatic balance, the volume of porous material plus voids is determined and by subtracting that of the porous material from this the volume of voids is ascertained. The rate of penetration of solutions can be determined either (a) by measuring the change in weight as the sample becomes saturated when immersed ni a liquid of know density, or (b) by measuring the volume of liquid penetrating with a dilatometer. In either instance, due to the fact that some penetration takes place as soon as the sample comes in contact with solution and before a reading can be taken, the sample must be paraffined to determine the total volume of penetration. Since many porous materials partly decompose and disintegrate in liquids the rate and volume of penetration can better be measured by dilatometer than by the change in weight, as saturation takes place when immersed in a liquid. The details of procedure for determining (a) total volume of voids, and (b) rate and volume of penetration are given in this paper."

Oct 1, 1930

By J. G. Donaldson

Optimum conditions are given for chloridizing pyrite, marcasite, chalcopyrite, arsenopyrite, stibnite, and covellite with chlorine gas. The formation of metal chlorides is affected by the time and temperature of chloridizing, and by particle size of the sample. Chloridizing data also are given for chemically precipitated antimony (III) sulfide and copper (II) sulfide.

Jan 1, 1962

By F. J. Wiebel

"INTRODUCTION As a result of a general survey of the iron-ore deposits of Califor¬nia, the Bessemer was one shown to offer possibilities of developing com¬mercial ore reserves. Surveying and exploring were done at the request of Congress for an investigation of raw materials for the production of steel.A wartime steel plant has been established at Fontana, San Bernardino County, and a backlog of iron-ore reserve for the maintenance of permanent steel industry on the West Coast will be of National benefit in the postwar period.W. D. McMillan, a mining engineer the Bureau of Mines, examined the property in May 1942, and it was reexamined by D. W. Butner, also of the Bureau, in October 1943. Geophysical work was done by the Bureau in 1944, and the property was explored by diamond drilling from April to August 1944 and February to SeptemberACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contri¬bution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, under the direction of Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, under the direction of R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

May 1, 1947

By Peter Townsend, Sergei Diachenko, Allan Moss

The Palabora Mining Company has successfully extended the life of its operation by developing a 30,000tpd block cave underground mine below the now closed open pit. The process of transitioning from surface to underground mining has been technically, operationally and managerially challenging. This has been due to a number of factors; in particular, the development of a block cave in a very competent rock mass. The competence of the rock mass is clearly demonstrated in the open pit that preceded the block cave, one of the steepest deep open pit excavations in the world. With cave breakthrough, however, the pit was ?instantaneously? deepened by 400m causing a major failure of the northwest wall involving close to 100Mt of waste material.

Jan 1, 2006

By Daniel N. Beshers, Ralph H. Condit

An expression for the diffusion coefficient of inlerstitial atoms in the bcc lattice is derived which takes account of jumps between tetrahedral and octahedral interstices. The results are applied to the case of carbon diffusion in iron to find values for jump frequencies of the types, octahedral-tetrahedral, tetra-hedral-tetrahedral, and tetrahedral-octahedral. ThERE has been renewed discussion1-5 concerning the mechanism of diffusion of interstitial atoms in the bcc lattice. This lattice has both octahedral and tetrahedral interstices, and it has been pointed out that the interstitial atoms may make jumps of the octahedral-octahedral type, hereafter called o-o, octahedral-tetrahedral, o-t, and tetrahedral-tetrahedral, t-t. Doubt has been cast on the applicability of snoek's8 model for internal friction to some interstitial migrations in bcc lattices wherein he proposed 0-0 jumps as the principal mechanism of migration. Also, the anomalous excess diffusion of carbon in iron at high temperatures4 has been ascribed to t-t jumps,2,3 even though the sites normally occupied are octahedral. In this paper an expression is derived for the diffusion coefficient, taking account of the three types of jump mentioned. The relationship of the coefficient to the corresponding internal friction relaxation time is found for the limiting case corresponding to Snoek's model. These results are applied to the case of carbon in iron. In Fig. 1, the structure is shown with the locations of the interstices. Each o site has four t site neighbors coplanar with it, and each t site lies halfway between two o sites. There are four t site first neighbors of a t site lying at the vertices of a tetrahedron. Let the average fraction of atoms occupying o sites and t sites be No and Nt, respectively. Since there are six o and twelve t interstices per unit cell having a lattice parameter, a, the concentration of interstitial atoms will It will be assumed that three types of jumps may be distinguished, t — t, t — o, o — t,for which the jump

Jan 1, 1968

By David F. Gearhart

The Burrell Can1 is a thin, steel, tubular shell filled with aerated concrete that is used as a roof support in coal mines. The Can height is always shorter than the mining entry, so it is capped with wooden timbers and wedges when it is installed. This combination of the Can and the wooden header is a standing support system that is designed to yield in a controlled manner and exhibit a constant yield, or elastic-plastic behavior. The Burrell Can is capable of withstanding 20 in or more of vertical convergence and 15 in or more of horizontal displacement. Because of this exceptional ability to sustain load through extended convergence and displacement, it is one of the most robust standing supports in use today. The National Institute for Occupational Safety and Health (NIOSH) conducted testing on seventeen Burrell Cans in 1995, during development of the support where the ratio of the height to the diameter, or the aspect ratio, was between 2:1 and 4:1. Based on the results of that testing, it was suggested that the standard aspect ratio of the Can be less than 5:1. This suggestion is intended to preserve the overall stability of the Can, which will help to maintain the initial stiffness and prevent load shedding. Recently, the necessity of the aspect ratio has been questioned, and this issue will be addressed in this paper. Since the initial development and introduction, more than 130 tests of the Can have been conducted at the NIOSH Mine Roof Simulator (MRS), and 25 of those specimens had aspect ratios greater than 5:1. The 18-in-diameter by 10-ft-tall specimens had the largest aspect ratio, 6.67:1.However, the aspect ratio is not the only parameter that affects the performance characteristics of the Can. Multiple factors, such as the use of different wood species, the use of different header or footer configurations, and the use of pedestals, as well as biaxial loading conditions can also decrease the stiffness and capacity of the Can. Data from full-scale tests that include these other factors are analyzed to show that the initial stiffness is primarily affected by the roof and floor contact configurations. Furthermore, load shedding is more likely to occur or begin earlier when the aspect ratio is greater than 5:1 and one or more of the other factors are present.

Jan 1, 2012

"In mineral exploration and mining applications, it is sometimes necessary to reduce sampling error in order to improve representivity of individual sample assays. Historic efforts to reduce sampling error have relied on the belief that larger samples exhibit less sampling error. Justifications for this belief traditionally have coupled the binomial theorem with an ideal geological material consisting of ore and gangue particles of equal size and shape (an equant grain model) and empirical tests of geological materials, to illustrate an inverse relationship between sample size and sampling variance. To date, no proof exists of this sample size-sampling variance relationship in real geological materials exhibiting variations in grain size, shape, composition, and degree of liberation.Using first principles calculus and the formula for the mean, sample mass and sampling variance are proven to be inversely proportional in all geological materials. Distribution assumptions and physically ideal geological models are not used in this proof. Furthermore, algebraic manipulations of expressions describing the variances of equant grain models consistent with binomial, hypergeometric, and Poisson distributions reveal that these models also exhibit an inverse sample size-sampling variance relationship. Thus, the sampling behaviors of these models are numerically consistent with the sampling behaviors of real geological materials, and these models can be used to estimate sampling errors in real geological materials using simple sampling parameters."

Jan 1, 2007

By G. Bartolacci, G. Couture, Levasseur. B., A. Lockhart, D. Nathan

"Pulp and froth zone characterization in a flotation circuit to improve transport of valuable minerals remains a challenge. Even though some significant breakthroughs have been made in the development of collectors in terms of selectivity, the control of gangue drainage is still the main bottleneck to achieve the production of a clean concentrate.Over the last decade, COREM’s team has been working on technologies to improve the selectivity of flotation circuits by tuning their hydrodynamic conditions using online instruments such as the bubble viewer, Jg sensor and gas hold-up. As part of its research program, COREM also developed the half-life column that establishes the relationship between the collection zone (bubble-particle attachment) and the cleaning zone (foam) of a flotation machine. In recent years, COREM has continued the development of the prototypes to make them more robust and improve the accuracy of their measurements.Recently, these hydrodynamic instruments were installed in an industrial process at Raglan Mine in order to diagnose and control the impact of hydrodynamic parameters versus the recovery and the quality of the Ni concentrate produced. Sampling campaigns of hydrodynamic parameters demonstrated that froth height could be optimized in order to increase recovery and quality of the concentrate at the same time. The specific effect of the froth height impacts both the pulp and the froth zones. Along with the impact on the drainage of the concentrate, it was observed that froth height also contributes to enhance the collection of particles in the pulp leading to an increase in metallic units.IntroductionOnce the particles of the minerals of interest are attached to the air bubbles injected in the pulp, the flotation process is driven by air dispersion parameters and froth properties. The pulp is usually responsible for the collision between air bubbles and hydrophobic particles of interest while the froth zone aims to upgrade the selectivity of the particles floated through drainage of the unwanted hydrophilic particles. Over the last four decades, flotation hydrodynamics has been extensively studied. Superficial gas velocity (Jg), gas hold-up (eg), Sauter mean bubble diameter measurements (d32) and bubble surface area flux (Sb) are among the most assessed parameters in flotation plants worldwide either to quantify the gas dispersion parameters or to optimize them (Fournier et al., 2015). McGill University has developed several sensors able to measure these parameters at industrial scale (Tavera et al., 1996; Finch et al., 1999; Chen et al. 2001)."

Jan 1, 2017

By A. Boominathan

The behaviour of single piles under lateral dynamic loading is very critical and the study is still a current field of research since 1950's. Though many methods have been developed analytically to estimate the dynamic lateral stiffness, very limited dynamic testing on full scale piles were carried out to study the response of piles under lateral dynamic loading. Hence, field lateral dynamic vibration tests are conducted on driven precast concrete square pile of 400mm size and driven cast in-situ concrete piles of 400mm and 500 mm diameter at a petrochemical complexes site at Haldia (India). The results of steady state and free vibrations tests are discussed herein and compared with the response of the piles estimated from PILAY.

Jan 1, 2002

Construction work on one of the world's largest landslide stabilisation projects is drawing to a close in Central Otago. Begun in mid 1990, major stabilisation work has been carried out on seven large rockslides which will be partially inundated when the Clyde dam reservoir (Lake Dunstan) is filled. The work has required the construction of 14.5 kilometres of tunnel, 60 kilometres of surface drilling, 78 kilometres of drilled drainage holes and five million cubic metres of earthworks. The stabilisation programme has been carried out by the Electricity Corporation of New Zealand as part of the Clyde Power Project, a hydroelectric development on the Clutha River.

Jan 1, 1992

By M. M. Fine

Chalcocite flotation concentrates (26-34 percent Cu and 6-7 percent S) were roasted in air to determine sulfur elimination as a function of temperature, airflow rate, and residence time. Fluosolids roasting was evaluated batchwise and continuously in a 4-inch fluid-bed reactor. Kiln roasting tests were carried out in a 4-inch ID by 6-inch-long rotary drum. Pelletizing the very fine concentrates prior to roasting was essential to minimize dust losses and accretions. Concentrate pellets, sized minus 10 plus 20 mesh and bonded with 2 percent bentonite, were excellent feed for fluosol¬ids roasting and limited dust losses to 10 percent or less. One-fourth-inch pellets were best suited to kiln roasting. Both techniques were capable of producing copper calcines analyzing well under 1 percent residual sulfur when operated at 900° C with average retention times of 3 to 4 hours. Calcined pellets were strong, porous, and readily reducible.

Jan 1, 1970

By M J. Kindley

The Golden Cross Gold Mine Project is now fully operational and into its second year of operation. Because of its location in the sensitive Coromandel Peninsula , strict water management and environmental requirements had to be met. This led to the development of new technologies for cyanide recovery and the adoption of advanced water management and water treatment systems. This paper discusses the water management and treatment system adopted for contaminated water at Golden Cross and provides data on the operational history to date.

Jan 1, 1993

Effect of pH and Chain Length on the Flotation Separation of Fluorite from its Synthetic Mixtures with Calcite and Dolomite with Imino-Bis-Methylene Phosphonic Acid

Sep 13, 2010

By Roy C. Bartholomae

This Bureau of Mines report presents the results of a laboratory investigation of coal cutting mechanics and noise. These experiments were performed using linear cutting apparatus that operates over a broad cutting speed range. The influence of several coal cutting parameters on the noise, force, productivity, and specific energy associated with linear cuts was ascertained. Some basic theoretical aspects of coal cutting mechanics and noise generation are discussed, and the results of the laboratory experiments are used to formulate analytical models of the coal cutting forces and noise. The analytical model for coal cutting noise is then generalized to account for the more important effects of rotary cutting. Based on the generalized model, an estimate of the sound pressure level at an operator's position is made for a typical continuous mining machine. It is concluded that by employing linear rather than rotary cuts, using deeper depths of cut, slower cutting speeds, and more efficient cutting tools, it is possible to reduce the level of coal cutting noise, as well as provide benefits to other important areas of health and safety in underground mining.

Jan 1, 1983

By D. D. Runnells

This study focused on the chemical reactions between uranium tailings fluids and cores of subjacent bedrock from the site of the Cotter Corporation uranium mill at Canon City, Colorado. Actual and synthetic tailings fluids were forced through cores of bedrock. The pH of the effluent solutions was the dominant control on the behavior of dissolved species in solution. The pH depended on the presence or absence of calcite cement in the rocks. Calcite neutralized acidic raffinates and caused the precipitation of iron, manganese, aluminum, and possibly uranium. Chloride, sulfate, and sodium were not retarded upon passage through the cores, and sulfate and chloride should be useful as tracers of escaping tailings fluids. Zinc, copper, cobalt, nickel, uranium, and vanadium exhibited high mobility under acidic conditions and were strongly retarded at elevated pH. Calcium was released due to dissolution of calcite and ion-exchange. Magnesium was not retarded in concentrated solutions, but showed moderate retardation in dilute fluids. Potassium and ammonium both showed early retardation followed by breakthrough and mobility. The behavior of molybdenum was strongly dependent on pH, with retardation at low pH and mobility at elevated pH. Selenium was highly mobile under all conditions. Selenium should be a better tracer than molybdenum for many situations. Precipitation of carnotite appears to control the solubility of uranium and, possibly, vanadium. With the exception of the precipitation of aluminum and silica, all reactions were rapid.

Jan 1, 1983

By M. Kanda

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in and above an operating coal mine, McElroy Mine, located near Moundsville, West Virginia. The electromagnetic environment created by 300 volt dc and 480 volt ac machinery was measured. In one technique noise was measured over the entire electromagnetic spectrum of interest for brief time periods. The noise was recorded using broadband analog magnetic tape. The noise data was later transformed to give spectral plots. In the other technique, noise amplitudes were recorded at several discrete frequencies for a sufficient length of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 1, 1974

By Y. P. Chugh

This is the final report of a study done by IIT Research Institute for the Bureau of Mines to identify the problem areas and technological inadequacies in noncoal (metal, nonmetal, stone, and sand and gravel) mining and processing systems that are the primary causes of death, injury and occupational disease, and to make recommendations to improve safety and health in these operations. The findings and recommendations presented in the report are based on: (1) analyses of MESA injury and employment data for the period 1961-70, MESA fatality reports for underground noncoal mines (1968-72) and lost time accident data for 1970-72 obtained from mining and processing operation: (2) visits to a variety of noncoa1 mines and mills throughout the country to observe the operations and to study the safety organization and practices used in the industry and (3) interviews with industry and government representatives knowledgeable in the field of noncoa1 mining and processing safety and health. The report provides a comprehensive overview of safety and health problems.

Jan 1, 1974