Search Documents

The aim of this investigation was to study the influence that varying production rates have on iron sinter quality. This was done by performing sinter pot tests at different pressure drops over the sinter bed, namely 11 kPa and 15 kPa (for 500 mm total bed depths). During each of the sintering processes temperature-time profiles were recorded of the top, middle and bottom layers of the sinter bed. On completion of the sinter process the sinter cakes were divided into top, middle and bottom layers. The physical properties of each layer were subsequently characterized by performing a tumbler test and a sieve analysis. A comprehensive mineralogical study was also conducted on each layer. This study revealed that sinters of similar cold strength could be produced under the examined production rates. However, a higher production rate was accompanied by an increased amount of fines. The cold strengths of both sinters significantly increased from the top layer to the bottom layer of the sinter bed. This strength variation is not related in any simple way to the phase composition. Keywords: Sinter, sinter bed, production rate, phase composition, cold strength, tumbler index, sieve analysis, temperature-time profile

Jan 1, 2003

By A. R. Biggart

Twenty-sixth Sir Julius Wernher memorial lecture, presented at the Tunnelling '94 symposium held in London, 5-7 July 1994. In describing 18 projects with which he has been involved over a period of 36 years, the author aims to illustrate how technological change and an increase in scientific knowledge have influenced tunnelling practice, which he nevertheless maintains does continue to be an art. Tunnels discussed are: the Silver Street, Blackfriars, Whitechapel, St. Paul's and Waterloo Post Office tunnels, 1958-1969; metro tunnels on the Victoria Line, London, 1962-1970; the introduction of tunnel boring machines (TBMs), 1971-1978, in the Empingham reservoir diversion tunnels in Rutland, the bentonite tunnelling machine experiment at New Cross, the Southern tunnel water main section of the London Ring Main and the Warrington sewer in Cheshire; tunnels in rock 1975-1981, for the Lune Wyre and Megget Manor aquaducts, Weymouth sea outfall and Bristol interceptor sewer; Priestley TBM tunnels 1969-1982; the Greater Cairo wastewater project 1983-1987; Anacostia River crossing, Washington DC 1985-1987; the Channel Tunnel 1987-1992; and the Storebaelt eastern tunnel in Denmark, 1992-1994.

Dec 1, 1994

By Margaret Anne Stephenson

While the concepts of Aboriginal title share a similar jurisprudence in both Australia and Canada resource development regimes on Aboriginal title lands differ significantly. In Australia, the process is the right to negotiate with mining proponents. In Canada, the process is the duty to consult with government regarding mining projects. This paper compares and assesses the processes for ?consultation and negotiation? with Indigenous peoples when development actions (particularly in the context of mining resource development) impact Indigenous property rights and how agreement making can be progressed. This paper will question whether the resource development processes afford Indigenous people?s property rights full respect when mining developments on Indigenous lands are proposed.

Aug 1, 2013

By Erwin L. Zodrow

"The neglect of including the toxic metal mercury in the list of escaping elements (Zodrow, CIM Bulletin, September 1982, pp. 138-140) was pointed out to the author in a private letter by J.E. Rehder, dated September 21, 1982. I welcome this opportunity to present my preliminary mercury research data based on coal investigations supported by N.S.E.R.C and the University College.As mercury is a volatile element and liquid at room temperature, special analytical techniques are required to determine concentrations in whole coal. In the investigation, the coal is analyzed by flameless atomic absorption with a lower detection limit of approximately 10 parts per billion, which, however, is a function of the ash contents of the coals (personal communication, J.L. Brooker, XRAL, 1981).Coal seams of the Sydney Coalfield studied so far include: the Point Aconi, a thin shaly coal, the Upper Bonar, an overrider of the Harbour seam, and the Harbour, Shoemaker and McAulay seams, all of which are shown in stratigraphic succession in Figure 1. The seams have been channel-sampled taking 15-cm coal intervals as one sample for analysis. One channel sample has been investigated from each of the seams listed (two channels were taken from the Point Aconi seam), resulting in 38 samples. Table 1 shows the results, which include mercury contents, ash and total sulphur per sample interval. Figure 2 is a frequency distribution of the 38 determinations."

Jan 1, 1982

By Peter Klaver

Deep tunnels have been used for decades for the temporary storage of large volumes of urban runoff, both storm water and combined sewer overflow (CSO). Tunnels are attractive because they reduce surface disruption and do double duty as storage and conveyance systems, collecting overflows from multiple locations and transporting them for treatment to various facilities. Like any hydraulic system, however, there are dynamic effects that must be fully understood during the design phase so that the final constructed product does not have unintended negative consequences. Preliminary sizing of storage tunnels is typically based on the total volume required. For example, if studies have determined that a volume of 56.8 ML (15 million gal) will provide the intended level of control, then that figure can be used, along with a preliminary idea of the desired tunnel length, to compute the required diameter. Of course, filling a long tube with water from various points along the way is not at all the same as pouring water into a bucket, and these dynamic effects require additional attention from design engineers. The rapid filling of storage tunnels can lead to the formation of bores, which are essentially moving walls of water. An open channel bore can build in height until it reaches the crown of the tunnel, at which point it becomes a pipe-filling bore. Figure 1 depicts both kinds of bores moving upwards in a rapidly filling tunnel. Bores can strike the ends of tun-nels with tremendous force, driving water and entrained air upwards into dropshafts and creating strong pressure surges in portions of the tunnel that are already filled. If the hydraulic surges are high enough to reach grade, they can cause overflows and/or damage structures at the surface. Trapped air pockets can occur through several phenomena, including the reflection of bores off dropshaft structures and the occurrence of ?premature pressurization.? The latter refers to the situation where the inflow to a tunnel is increasing more rapidly than the tunnel can convey it, such that the pipe becomes surcharged at an upstream point while points downstream are still flowing as an open channel. These air pockets are a great nuisance as they migrate toward points in the tunnel where they can rise to the surface, which are often shafts that are already filled with water (Fig. 2). The ?geyersing? that results can be hazardous and costly.

Jan 3, 2010

By Thomas Fraser

"INTRODUCTION The Santa River Valley of northern Peru contains extensive deposits of a good-grade anthracite that offer one of the most accessible sources of solid-fuel supply for South America. This region is served by the narrow-gage railroad of the Corporation Peruana del Santa, which taps the coal fields along the Chuquicara River and terminates at the port of Chimbote, where facilities have been provided for loading coal into ocean-going vessels.This Government-sponsored corporation is prosecuting a vigorous program of development in this region, envisaging an intensively industrialized area around Chimbot Bay, fueled and powered by the anthracite of the upper valley and a hydroelectric generating plant now being constructed in the Cahn del Fate, where the Santa River has cut through the coastal range of the Andes.This development also includes the construction of extensive irrigation works to greatly expand agricultural production in the valley and thus estab¬lish the basis for a prosperous, well-balanced, industrial and agricultural community. It is hardly necessary to point out the importance of the local anthracite-mining industry to this general plan.At the invitation of the Peruvian Government, through the agency of David Dasso, chairman of Corpoacion Peruana del Santa, a technical mission was sent to Peru in March, April, and May 1945 to examine these coals and assist the corporation in promoting preparation of the coal for most effective use in the contemplated expansion of industry and trade."

Feb 1, 1948

By Mark Sanders

This report describes an experiment which was conducted to compare the relative bumping hazard of a low and high profile hard hat (helmet) in a low seam mining environment. The study was specifically designed to assess the effect of lowering the helmet profile on frequency of head impacts in an underground low seam coal mine simulator. This involved subjects performing four common low coal mining tasks wearing the low and high profile helmets in the low seam simulator (36" and 48? heights). The results of the study indicated that a low profile helmet could reduce bumping frequency in underground low coal approximately 25%, and as much as 80% on selected tasks. It was beyond the scope of the study to measure the impact force, thus it was not possible to estimate the effect of the low profile helmet on severity of impacts underground. The research team recommended that a more extensive investigation be made of head injuries experienced in low seam mining (both underground and surface) with the objective being to assess the impact of a low profile helmet on total head accident exposure.

Jan 1, 1980

By Mike Faure

Hercules cribs make use of timber loaded parallel and perpendicular to the grain. Maximum use is made of the orthotropic properties of timber resulting in crib- having superior strength, high initial stiffness and controlled post yield deformations. Blocks and timbers can be combined in many different ways resulting in thousands of different geometries. Each geometry has a specific combination of block on block, timber on timber and block on timber contact area which results in a unique performance. Each crib can be fingerprinted by defining four parameters relating to its load/deformation curve. If the geometry is known, the performance can be predicted with a high degree of accuracy. If the mine support requirements are known, the crib geometries can be designed which met theme requirements in the most cost effective manner Hercules cribs come closest to satisfying mine support requirements. Due to the flexibility of the concept and their superior strength, they can be employed in most mining situations to enhance safety, improve productivity, reduce working costs or improve profitability.

Jan 1, 1993

Many states rely upon the Pennsylvania 1957 “Gas Well Pillar Study” to evaluate the coal barrier surrounding gas wells (Commonwealth of Pennsylvania, 1957). The study included 77 gas well failure cases that occurred in the Pittsburgh and Freeport coal seams over a 25-year span. At the time, coal was mined using the room-and-pillar mining method with full or partial pillar recovery, and square or rectangle pillars surrounding the gas wells were left to protect the wells. The study provided guidelines for pillar sizes under different overburden depths up to 700 ft. The 1957 study has also been used to determine gas well pillar sizes in longwall mines since longwall mining began in the 1970s. The original study was developed for room-and-pillar mining and could be applied to gas wells in longwall chain pillars under shallow cover. However, under deep cover, severe deformations in gas wells have occurred in longwall chain pillars. Presently, with a better understanding of coal pillar mechanics, new insight into subsidence movements induced by retreat mining, and advances in numerical modeling, it has become both critically important and feasible to evaluate the adequacy of the 1957 study for longwall gas well pillars. In this paper, the data from the 1957 study is analyzed from a new perspective by considering various factors, including overburden depth, failure location, failure time, pillar safety factor (SF), and floor pressure. The pillar SF and floor pressure are calculated by considering abutment pressure induced by full pillar recovery. A statistical analysis is performed to find correlations between various factors and helps identify the most significant factors for the stability of gas wells influenced by retreat mining. Through analyzing the data from the 1957 study, the guidelines for gas well pillars in the 1957 study are evaluated for their adequacy for room-and-pillar mining and their applicability to longwall mining. Numerical modeling is used to model the stability of gas wells by quantifying the mining-induced stresses in gas well casings. Results of this study indicate that the guidelines in the 1957 study may be appropriate for pillars protecting conventional gas wells in both room-and-pillar mining and longwall mining under overburden depths up to 700 ft but may not be sufficient for protective pillars under deep cover. The current evaluation of the 1957 study provides not only insights about potential gas well failures caused by retreat mining but also implications for what critical considerations should be considered to protect gas wells in longwall mining.

Jul 28, 2020

By R. J. Leary

The technologies of contemporary iron and steel production and of direct reduction processes have been studied to identify and estimate the potential effects of direct reduction on mineral consumption and the problems raised thereby for the Nation's mineral supply to the iron and steel industry. Contemporary patterns of mineral raw material and energy consumption were determined from a study of the 1964-70 period. Major changes were observed in requirements for 14 of 20 principal commodities. Average practice in 1970 was compared to best practice to estimate the potential effects of implementing existing technology without recourse to direct reduction. Potential effects of direct reduction were estimated by comparing the mineral requirements for 95 percent reduced pellets with 1970 best practice technology for two cases of use: (I) complete substitution for hematite pellets in blast furnace burdens, and (11) partial substitution (40 percent) for scrap in electric furnace steel charges. Effects upon mineral supplies are described; important collateral factors are analyzed, and the principal metallurgical, industrial, and environmental consequences of implementing direct reduction are discussed. Major effects of direct reduction on the domestic steel industry and its mineral supply system are foreseeable. Direct reduction will (1) create a large demand for low-gangue iron ore; (2) relieve the dependence of the steel industry on coking coal, and (3) permit great increases in furnace productivity, both in blast furnace ironmaking and electric arc furnace steelmaking.

Jan 1, 1973

By Wolfgang G. Brunner

The center of Berlin is currently a huge jobsite, where international architects, designers, consultants, construction and ground engineers as well as investors take on the challenge of the biggest and probably most complicated projects in terms of soil conditions in Europe. The Berlin sand is generally suitable for foundation measures, but can be very tricky in deep excavation pits below the high ground water level. The reason for this is its uniform grading, medium dense stratification and lack of cohesion. The requirements for these deep pits are: - measurements in the range of up to 120 000 m2 per pit - depths up to 19 m below ground water level - lack of dense horizontal geological layers - no permission for lowering ground water levels - toughest ever European competition in construction. Sheet pile walls, sheet piles set into cut - off walls, secant pile walls, diaphragm walls, all with tie backs under high water pressure, are used as retaining sytems. The pits are closed at the bottom against water either by under water concrete, deep lying grouted cut - offs or high lying jet - grouted cut - off slabs. The huge dimensions of these excavation pits are a new challenge for ground engineers, and new technology had to solve the upcoming problems and resulted in new experience.

Jan 1, 1999

By G. M. Steed, A. O. Oyinloye

The deposit lies in amphibolite-facies biotite granite-gneisses of Proterozoic age, 4 km east of a major crustal break known as the Ifewara-Zungeru fault. Gold mineralisation is contained in a zone of quartz-carbonate (mainly calcite) veins and hydrothermally altered gneisses with associated small-scale intrusions along a steeply dipping second-order fault zone that roughly parallels the main fault. Gold is present mainly at grain boundaries between quartz and carbonate as discrete particles up to 100 micrometres in size, in general association with sparse, scattered pyrite, pyrrhotite and some base metal sulphides. Adjacent to the gold-bearing zone the granite-gneisses have been hydrothermally altered with minor volume increase, most notable enrichment being in K2O, S, Pb and Cu (and Au). High concentrations of Th, Y, Ce and Zr in the granite-gneisses imply derivation from S-type granites. It is likely that their high heat production capacity maintained the high temperatures needed to transport gold in the hydrothermal systems. It is most probable that the mineralisation dates from the Pan-African orogeny (650-450 Ma)

Apr 1, 1996

By I. A. Mwamba

Plain and alloyed titanium aluminides of composition Ti-47.5 at.% Al were prepared by melting commercial-purity titanium and aluminium with additions of 1 at.% precious metal. The as-cast alloys were subjected to potentiodynamic scans in 5, 15, and 25 wt% HCl aqueous solutions at room temperature and compared for their abilities to spontaneously passivate. Addition of precious metals resulted in a general improvement of corrosion resistance by increasing the open circuit potential to more noble values. Addition of 1 at.% gold or silver to titanium aluminide did not significantly increase the corrosion potential (Ecorr) above that of the plain titanium aluminide alloy, indicating that gold and silver are not sufficient cathodic modifiers to improve the corrosion resistance of titanium aluminide in all the solutions tested. However, platinum, palladium, and iridium additions shifted the corrosion potentials to the position of the passive region of plain TiAl for all solution concentrations. This indicated that TiAl alloyed with these platinum group metals would passivate spontaneously by cathodic modification. TiAl alloyed with palladium performed the best in 5 wt% HCl solution with the most positive corrosion potential. In 15 wt% HCl solution, alloys with platinum exhibited the most positive corrosion potentials, while alloying with iridium or palladium revealed more negative corrosion potentials. Thus, palladium alloying led to the best cathodic modification of titanium aluminide in low-concentration HCl solution, whereas platinum and iridium alloying additions resulted in the best cathodic modification of titanium aluminide in high-concentration HCl solutions.

Jan 1, 2013

By A. G. Starliper

The Bureau of Mines made laboratory investigations to determine the feasibility of utilizing fine tungsten wires to reinforce a number of nonferrous metals and alloys and a superalloy, S-8l6. The composites of tungsten filament and metals were chosen to attain elevated temperature strength and corrosion resistance. Oriented clean or precoated tungsten wires were incorporated with the other metals by extrusion, swaging, and infiltration casting. Although widely varying characteristics were found in the composites, none were considered satisfactory for high-temperature use, chiefly because of reactions between the matrix metal-tungsten surface. Diffusion, solution, and chemical reactions between matrix and tungsten wires were sufficiently slow for some combinations, such as 15 v/o 8-816, to exhibit increased high-temperature strength for a limited time. A few metals failed to wet or bond to the tungsten surfaces, while a few responded after precoating with a third metal.

Jan 1, 1968

By Y X. Xue, J Pan, D Q. Zhu

In order to reveal the correlation between the fundamental sintering characteristics of iron ores and their real sintering behaviours, a comprehensive evaluation index is proposed based on the measurement of four high temperature indexes, ie assimilation temperature, liquid phase bonding strength, liquid fluidity and calcium ferrite formation percentage, and the sintering pot tests of single ore fines and their blends. The results show that both the lowest assimilation temperature and liquid fluidity of ore blends appear to be the linear superposition of those of single iron ores except for the liquid phase bonding strength and calcium ferrite formation percentage. Furthermore, the tumble index of the sinter product obtained from blended iron ores also corresponds to a linear superposition of that of single ores, but not for the solid fuel rate and productivity. The comprehensive strength index YT exhibits a credible linear positive correlation with the four high temperature reactivity indexes, whereas the comprehensive productivity index YP possesses a lower correlation with the four high temperature reactivity indexes. The comprehensive strength index YT developed can predict the tumble index of the sinter product quite well, but the comprehensive productivity index YP cannot be used to evaluate the productivity effectively.CITATION:Zhu, D Q, Xue, Y X, Pan, J and Shi, B J, 2017. Correlation between high temperature sintering characteristics and sintering behaviours of iron ore fines, in Proceedings Iron Ore 2017, pp 123–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By G. G. Goble

Significant progress has been made in the past decade in determining the load bearing capacity of pile foundations. Developments in the means of prediction of pile capacity as limited by soil strength have been substantial, particularly in the use of dynamic methods. The use of currently available equipment, analytical procedures, and practices in the field, will often produce material economies on a job by allowing increased loads with proven factors of safety. This approach justifies the minimum number of piles required for a safe foundation in a wide range of job sizes and soil conditions. To avoid exposing the reader to excessive detail in the body of this paper, technical topics have been covered more thoroughly in several appendices. I. Wave Equation Analysis of Piles Appendix A II. Dynamic Monitoring and the Pile Driving Analyzer Appendix B III. Case Method Capacity Calculation Appendix C IV. Case Pile Wave Analysis Program Appendix D 1 Preliminary Analysis In designing driven pile foundations, there must be a close relationship between design, construction control procedures, driving practices, and the size of the job. Small commercial buildings or residences involving loads that are only a fraction of the pile capacities do not justify the expense of detailed design processes or elaborate construction controls. Nevertheless, some preliminary analysis of the job requirements and a limited subsurface investigation must be made to understand existing conditions and the possible foundation solutions. In other words, it is necessary to determine that driven piling is the best overall choice of foundation.

Jan 1, 1988

By Baker G

The exposures resulting from development work, following on the discovery of a new shoot of hIgh grade ore at the north end of the Sardine tin mine, during 1952, have provided an unusual opportunity to study the oxidation of a stannite-rich ore. Through the kindness of C. C. Morton, Chief Government Geologist of Queensland, an exactly located suite of specimens representative of the exposures was supplied by J. and W. Reddie. This was later supplemented by a number of specimens culled from a parcel ofrepresentative ore submitted to the Melbourne Ore Dressing Laboratory for testing.The Sardine tin mine, near Ewan, Queensland, has been the outstanding producer of the Kangaroo Hills Mineral Field. Since its discovery in 1918, up to 1952 it has yielded about 1,500 tons of cassiterite concentrates, and about 85 tons of stannite concentrates. The outcrop ore averaged 35% tin oxide, but the grade declined with increasing depth, and by 1930 had fallen to 7% tin oxide. In the northern section of the mine the ore shoots show a downward passage to complex primary s.ulphide ore, containing cassiterite and abundant stannite.The orebodies occur in a series of fissures in a crushed zone about 50 ft. wide in slates and quartzites that have been intruded by granite (Connah, 1952). A quartz porphyry dyke forms the footwall of the original main lode in its southern part, being traced' from the surface to' the No. 4 level (173 ft. vertical depth), and two narrow dolerite dykes were encountered in the workings north of the main...

Jan 1, 1954

By H Thanasekaran, L Christodoulou, J Kohmuench

"Column flotation has been successfully applied to iron ore concentration since the 1980s with the goal of reducing silica content and allowing for the efficient production of pellet feed. Since then, columns have been widely used in iron ore processing due to: their lower capital and operational costs when compared to conventional cells their ability to generate higher concentrate grades and recoveries.Currently, more than 100 columns have been installed within Brazilian iron ore processing circuits for rougher, cleaner and scavenger duties. Despite it being a well-established approach, several technological advances have improved column design, accessories and performance. This work presents the performance of some iron ore columns in Brazil and the recent technological developments.CITATION:Thanasekaran, H, Kohmuench, J and Christodoulou, L, 2013. Column flotation of iron ore - status and advances, in Proceedings Iron Ore 2013, pp 479-484 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By Brian Hart, Roger St. C. Smart, James Francis, Mark Biesinger

"There are a number of challenges involved with the surface analyses of different mineral phases from process streams in a flotation facility. The first of course is to collect samples that are representative of the process and to ensure that they remain in a pristine condition prior to introduction into the instrument. In mineral processing, sample collection from the different streams is done on site and preservation involves simply removing oxygen from the sample by bubbling nitrogen or argon gas through the sample and snap freezing with dry ice.The second challenge in studying the surface chemistry of specific minerals is to find reliable methods of mineral phase recognition. In surface analysis of mineral particles confident mineral selection can be difficult with many multi-metal minerals (e.g. chalcopyrite, pyrite, sphalerite) and with precipitated, adsorbed, reacted and contaminant species in the outermost molecular layers.In this paper we show that principal components analysis (PCA) of ToF-SIMS data provides improvement in phase recognition, particle selection and associated variations in surface species. We will demonstrate, with specific examples, that this technique can be utilized to differentiate surface chemical factors promoting (hydrophobic species) or inhibiting (hydrophilic species) flotation.Species recognition based on the PCA method in a study of Cu transfer between chalcopyrite, pyrite and sphalerite mineral mixture clearly identified a statistical difference in copper intensities between the sphalerite and pyrite phases. A similar ToF-SIMS/PCA based study applied to concentrate and tails samples collected from the Inco Matte Concentrator demonstrated extensive CuOH and NiOH transfer between the chalcocite and heazlewoodite minerals. The statistical analysis has been able to confirm some mechanisms and deny others proposed to control recovery and selectivity giving more focus on the control factors.The ToF-SIMS PCA statistical analysis has elucidated differences in surface chemistries which illustrate the discriminating depressant action of adherent aluminosilicate (gangue) fine particles and adsorbed ions on the surface of sphalerite grains. In the flotation test concentrates, HIC conditioning resulted in the removal of these gangue fines thereby improving surface collector attachment efficiency, promoting a greater recovery of sphalerite."

Jan 1, 2007

By D M. Menne

This paper is intended to give a general review of current gold extraction technology for free-milling or non-refractory auriferous ores. Fundamental process concepts and some of the differences between the current technologies is referred to. Typical flowsheets and layouts are provided and it is demonstrated that technology for extracting free-milling gold is relatively simple. For environmentally sensitive areas such as encountered in New Zealand relevant cyanide decay and destruction technology is also discussed. Brief mention is made of some likely future innovations. Finally reference is made of New Zealand's previous significant contribution to gold extraction technology. These contributions were pioneering ranging from the cyanide leaching of gold to adsorption by carbon and precipitation by zinc. New Zealand has not allowed its potential gold projects to develop at a rate commensurate with the rest of the world thereby stifling its renowned innovative approach in this technology. It is time for New Zealand mining to recognise its unique opportunities in developing gold extraction technology and again take a rightful place in leading the way.

Jan 1, 1986