Search Documents

By R. L. Marek

The number of persons fatally injured in the California petroleum industry in 1931 was 30, a decrease of 20 fatalities or 40 per cent from the number killed in 1930. As a result of the decrease in the number of fatalities for 1931, the fatality curve of tie California petroleum industry reached its lowest point in nine years. Although reductions in personnel--which permitted the retention of a select and experienced class of workmen, decreased active field-development work, and curtailed production--undoubtedly have had a marked effect on reducing the number of fatalities in 1931, the decrease also has resulted from continued accident-prevention efforts. Statistics show that a direct relationship exists between development activity and the number of men accidentally killed in the drilling and producing division of the California petroleum industry. For example, when the average number of drilling wells in 1930 was 29 per cent less than in 1929, the number of men accidentally killed at drilling wells dropped 48 per cent; and when the average number of drilling wells in 1931 decreased 52 per cent from 1930, the number of fatalities at drilling wells decreased 58 per cent. The relationship between field-development work and fatality frequency is significant because each year at least 50 per cent of all the fatalities in the California petroleum industry occur in the drilling and producing division. This relationship should serve to guide the accident-prevention efforts of the industry, especially in the drilling and producing division, toward checking an increase in fatal accidents when development activity again takes an upward trend.

Jan 1, 1932

By Richard F. Hewlett

Engineers at the Bureau of Mines Denver Mining Research Center have been a research program investigating the theory and application of mine sampling. Part of this program is an investigation of the efficiency of sampling methods that involves development of sampling-method theory through simulating ore-deposit samples and assays, using - electronic digital computer. Theoretical developments are checked against actual ore-deposit sampling, assay, and production data by the commonly used polygonal and triangular methods of computing grade and tonnage of ore reserves. To speed the computing procedures, a program has been developed utilizing a medium-size digital computer for computing ore reserves by the polygonal method. This program calculates nine prismoids per minute at a total cost of $0.21 per prismoid. The complete program, written for an augmented IBM 650 computer, is described in detail; it can be used without change for computing ore reserves for a low-grade deposit. Modifications necessary to convert the program to compute ore reserves for virtually any other type of deposit or grouping of ore horizons also are given; however, the program is limited to using only vertical drill-hole data.

Jan 1, 1962

By P Blattner

The Late Miocene gold-silver bearing epithermal system at Waihi has some close similarities in its paleo-thermal and geochemical structure with modern, volcanic-hosted geothermal systems such as Ohaaki-Broadlands. At Waihi an extensive braided quartz vein system is enveloped by hydrothermally altered andesites with minor tuff breccias and tuffs. A main stage of vein filling consists of multiple phases of chalcedonic quartz and fine to medium grained quartz, which are accompanied by pyrite, sphalerite, galena, chalcopyrite and acanthite below the base of oxidation. Platy calcite is present locally. Fluid inclusion studies indicate that the main stage quartz was deposited at temperatures of 189¦-273¦C from dilute (Tm of -0.1 to -1.0¦C) fluids that were locally boiling. Homogenisation temperature Th versus Tm data points lie within the field enveloped by dilution and boiling/gas loss paths determined for the Ohaaki geothermal field, and indicates that the parent hydrothermal fluid for the Waihi epithermal system had a similar composition to that at Ohaaki, ie 0.2 wt% equiv NaCl and 3.3 wt% equiv CO2. The hydrothermal alteration mineralogy and the isotopic composition of vein calcite indicate that the hydrothermal fluid contained relatively high concentrations of CO2 , as at Ohaaki. Oxygen isotope analyses of main stage quartz range from 6.1 to 11.6 %0 and of vein calcite from 2.29 to 9.4%0. Calculated d18Owater values for the hydrothermal fluid that deposited the main stage quartz range from 2.0 to -5.7%0, with a trend to less negative values with depth. They are similar to those in the deep chloride fluid in active geothermal systems with a substantial fluid throughput. A high fluid throughput at Waihi system is also evident from the extensive high intensity hydrothermal alteration and large volume of quartz deposited in the vein system.

Jan 1, 1995

By V P. Elpatyevskaya, V S. Arzhanova

Main geochemical problems concerning the environment and mining industry interrelation are connected with the transformation of natural water chemistry by mining wastes. The investigation of many mines in Primorye, the southern part of the Russian Far East, showed that their mining waters have high concentrations of heavy metals and aluminium. Water acidity is primarily connected with the amount of acid-forming sulphide minerals in ores and also depends on the neutralising capacity of rocks. Considerable quantity of metals occur in the waters in dissolved form. Metal concentrations in mining waters exceeds the natural levels by two to five orders of magnitude and can't be reduced to the background levels even after multiple dilution. It is necessary to develop and put into practice new technologies so that to reduce the geochemical impact upon the environment.

Jan 1, 1995

By K. L. Paciorek

The aim of the present study is to determine on a gram per gram basis the toxic products of the thermal oxidative degradations of selected compositions. Four families of materials were investigated under the subject contract namely polyvinyl chloride and neoprene compositions, rigid urethane foams I and woods. Three methods were employed to conduct the thermal oxidative degradations: a sealed system (quiescent environment) I a stagnation burner arrangement (dynamic environment) I and a flow-through apparatus (dynamic I but less severe than stagnation burner conditions). The majority of tests were conducted using the first two systems; only limited experiments were carried out employing the third decomposition procedure. All decomposition was done at temperatures of 370 -4000C I the higher temperature being used in the stagnation burner. It has to be stressed that the nature of the products and the relative product concentration are temperature dependent. Thermogravimetric and differential thermal analyses were performed to supplement and extend the above delineated studies and to explore the feasibility of using these analyses as a method for material differentiation.

Jan 1, 1973

By G. F. Butterworth

The metallographic structures most frequently encountered in rifle barrels, and which are illustrated by the accompanying photomicrographs, fall naturally into two groups, distinguished by the method used to, produce in the stock a physical condition having the requisite properties. The fist group consists of "rolled" barrels; that is, barrels subjected to hot working by rolling in or near the critical range. In the second group, the stock, which is smaller in diameter than the first, is upset to form the butt end and is then heat treated by giving it a quench and a draw. These barrels will be referred to as " heat-treated " barrels. The structure of the rolled barrels resembles closely that of the same steel after annealing. There is the same network of excess ferrite outlining the grain boundaries, but the grains themselves are composed of sorbite rather than pearlite. The grain size is closely related to the rolling temperature. The critical-point curves of this grade of steel, which is approximately 0.50 to 0.60 per cent. of carbon and 1.00 to 1.30 per cent, of manganese, show a single very pronounced point between 1300" and 1350" F. (704" and 732" C.). Barrels rolled within this temperature range give an exceedingly fine grain, shown in Fig. 1. In fact, the grains may be so fine that, at a low magnification, they may be confused with the heat-treated structure shown in Fig. 6. A magnification of 500 diameters, however, will always resolve a rolled barrel into the characteristic structure shown in Fig. 2. As the temperature is increased, the grains are found to be larger. If, on the other hand, the rolling temperature is below the critical range, the structure previous to rolling will not be obliterated, the only effect of rolling being to elongate the coarse sorbite grains in the direction of rolling, Fig. 3. This distortion is greatest at the muzzle. Heat-treated barrels are quenched in oil from above the critical range, which should give a martensitic structure, Fig. 4, but the presence of some troostite in the martensite is frequently noted when the quench has not been sufficiently drastic, Fig. 5. The structure brought about by the subsequent draw is not so striking, though quite as typical. It is sorbitic or sorbito-pearlitic, and under a low magnification appears almost homogeneous, as in the case of fine grains of pepper and salt well mixed together, Fig. 6. This structure is substantially the same for all

Jan 1, 1920

By J. C. Ion, O. Isaksson, J. Stjernberg

Iron ore pellets are a preferred feedstock for ironmaking. One method used for pelletizing is the grate-kiln process, first established in 1960.During the past decade, the establishment of new grate-kiln plants has increased rapidly, especially in China, and new constructors of pellet plants have started to operate in the market. It is well known that the grate-kiln method yields a superior and more consistent pellet quality compared with the straight-grate process. However, certain issues exist with the grate-kiln plant, which are discussed here, together with proposed practical solutions.

Jan 1, 2015

The Australian Centre for Minesite Rehabilitation Research (ACMRR) was established through a mining industry initiative to meet the need of industry, governments and the community for sustainable systems for land affected by exploration, mining and mineral processing activities. The Centre, which is a consortium of the major groups associated with mining rehabilitation research in Australia, has a focus on both strategic research and technology transfer and combines a wide range of multidisciplinary skills covering engineering and the physical and biological sciences. The paper briefly describes the goals, structure, expertise and research and technology transfer activities of the Centre. The major research program areas of waste rock dump and final void stability, acid mine drainage, tailings disposal, and remediation of ecosystem reconstruction are described in the context of national priorities.

Jan 1, 1995

By G. G. Roy, R Shekhar

Pachuca tanks are extensively used for the cyanide leaching of gold and the carbonate leaching of uranium, processes in which oxygen mass transfer plays a very important role. Experiments were carried out to clarify the effect of design and operating parameters on oxygen mass transfer. Parameters such as the ratio of tank height to tank diameter, the ratio of draught-tube diameter to tank diameter and the tank design were found not to influence oxygen mass transfer. Results also showed that equal superficial gas velocities may be used as a criterion for scaling up oxygen mass transfer in both full-centre-column and free-air-lift Pachuca tanks with clear water. A volume-averaged, volumetric gas-liquid mass-transfer coefficient (k'av) was used to characterise oxygen mass transfer in full-centre-column tanks. The axial dispersion model was used to determine k'av. The resulting model used only tank geometry and air flow rate as inputs for the prediction of k'av in industrial-scale tanks. Predictions from the model show clearly that "local" mass-transfer coefficients, measured at one or two locations, may not adequately represent gas-liquid mass transfer in industrial tanks. It is therefore necessary to obtain an estimate of k'av

Jun 18, 1905

By D. Craig Camp

conditions. The soils included 65 m of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2, 130 meters of soft clay, silt, and sand not exceeding 30standard penetration test SPT blows per 300 mm, and 220 m of rock ranging between an UCS of 400-600 kgf/cm2. The river crossing, utilizing 1778 mm OD x 19 mm wall x600 mm steel casing pipe without intermediate jacking stations, was part of a seven kilometer liquefied natural gas (LNG) transmission line in South Korea. This 440-m, 1,442-ft, river crossing was microtunneled through three different ground conditions and completed in just over three months. The crossing was achieved with an average of 25 m of ground cover and 15 m of water cover. The Kwang Yang River Crossing was part of a 7 km liquefied natural gas pipeline project for POSCO, a Korean steel producer. The microtunneling machine was custom built for this project. The microtunneling machine selected for this project was tooled with 7 button bits and 2 roller bits. None of the cutter bits were replaced during the drive. Inside the machine, before the spoils laden slurry was pump back to the surface, it would pass through an independent cone crusher. The crusher is placed in the slurry flow to make sure that none of the spoils are so large as to stop the return flow of the slurry. An additional requirement was for the inclusion of a compressed air lock. The air lock was required in the event that the cutter tools required replacement. The cutters were back loaded so that the workers would have access to change the cutters in the event of cutter failure or wear out. No intermediate jacking stations were installed for the drive. The soils included 65 meters of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2 with production averaging between 7 and 20 mm/minute. The second zone contained 130 meters of soft clay, silt, and sand not exceeding 30 standard penetration test (SPT) blows per 300 mm with production averaging between 80 and 180 mm/minute. The third zone contained 220 m of rock ranging between an UCS of 400-600 kgf/cm2 with production averaging between 7 and20 mm/minute. The steel casing pipe was 1778 mm OD x 19 mm wall x 6000 mm long. The project profile, see Figure 1, shows the soil conditions. The hand written numbers locate just above the pipeline are the production dates. The circled numbers are the 10 pipe joint increments. The project required 74 pieces of pipe to span the440 m drive. Figure 2 and Figure 3 are the jacking information. Figure 3 is a continuation of the information from Figure 2. The top section of the graph is the jacking force. The jacking

Jan 1, 2001

By R. G. Gillies

The pipeline transport of paste, backfill or thickened tailings slurries is an important component of the tailings disposal process in many mines around the world. These mixtures contain significant fractions of fine (clay) and coarse (sand) particles, causing them to exhibit non-Newtonian flow behaviour and high frictional pressure gradients. There is often economic incentive to operate these pipelines in the laminar flow regime. Irrefutable evidence has shown that coarse particle settling can occur during the laminar flow of these slurries even when static settling tests show no indication of such behaviour. Previously, a ?rule-of-thumb? minimum frictional pressure gradient of ~1.5 to 2 kPa/m was suggested to ensure effective sand transport, based on the results of tests conducted using viscous Newtonian oils. In this paper, we examine the results of laminar flow tests of non-Newtonian, coarse-particle laden slurries conducted with pipeline loops of 50, 100, 150 and 250 mm in diameter. The results indicate that the ratio of the mean wall shear stress to the mean surficial particle stress is a better indicator of laminar flow settling tendency than frictional pressure gradient.

Jan 1, 2007

By Seppo Lähteenmäki, Pertti Koivistoinen, Jaakko Levanaho

"This paper describes the benefits and disadvantages of fully autogenous grinding when compared to grinding with steel grinding media. The study is a real case study based on a low tonnage, high grade mining project in a remote location in a developing country. The study compares the capital and operating costs of using either SAG mill, Ball mill, Crusher (SABC) or fully autogenous (AG) grinding circuits and produces an economical analysis of the project for both options. The economics have been developed for the overall project, including mining, processing, environmental and the infrastructure as well as for the additional cost of constructing a fully autogenous grinding circuit instead of the original plan of a SAG Mill, Ball Mill circuit.The paper also describes the development of the autogenous grinding circuit at Outokumpu Oy, Pyhäsalmi mine. This experience was used to design the autogenous grinding circuit for the case study. Pyhäsalmi Concentrator has over 30 years of experience in operating autogenous grinding circuits and therefore provides a sound base for the new circuit design.INTRODUCTIONGrinding of ore using steel grinding media is currently the most commonly used method in the mining industry. Autogenous grinding, ore replaces iron media, is also common especially in Europe and Africa. Iron ore industry in North America uses autogenous grinding in primary and/or secondary stages extensively. In gold, copper and other base metal industries, autogenous grinding is not as common, although there are operations where pebble grinding is or has been used in the secondary grinding stage. There are many variations of autogenous grinding in use in the mining industry. These variations include different mill sizes, mill length to diameter ratios, ore lump sizes, screening and pebble crushing configurations."

Jan 1, 2000

By John C. Machisak

INJURY and employment figures for nonmetal mines and mills in 1959 are presented in this publication. Data for nonmetal mines are presented separately from those for nonmetal mills. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry each year requesting their voluntary submission of injury experience and employment data. The voluntary response to these requests has contributed greatly toward the promotion of safety in the industry, and every effort has been made to make the information as complete as possible.

Jan 1, 1963

By C. L. Kosmoski

The mining industry faces many workplace hazards that are a threat to human health and safety. The Bureau of Labor Statistics has found that employees in coal mining are more likely to be killed or sustain an injury or illness than workers in private industry. These injuries are also likely to be more severe (Bureau of Labor Statistics, 2007). In recent years, coal mining injuries have attained national attention due to highly publicized disasters. Despite these threats to worker safety and health, the U.S. relies on the mining of coal to meet its need for electrical power, with42% of electricity in the U.S. generated through the burning of coal (U.S. Energy Information Administration, 2012b; United Mine Workers of America, n.d.). Furthermore, the production of coal continues to increase and reach record levels every year(National Mining Association, 2012; U.S. Energy Information Administration, 2012a). For this reason, the coal mining industry must continue to find ways to protect its workers while maintaining productivity. One potential approach to protecting workers while maintaining productivity is through improving the safety culture at coal mines. In order to achieve this culture, operators, employees, the inspectorate, etc. must share a fundamental commitment to safety as a value. This type of culture is known in other industries as a ?safety culture? and can be defined as the characteristics of the work environment, such as the norms, rules, and common understandings that influence facility personnel?s perceptions of the importance that the organization places on safety. Fundamental to improving safety culture within an organization is understanding the existing safety culture; improvements cannot be made without first elucidating areas that require improvement. This manuscript details the process undertaken by researchers at the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) to assess the safety culture at five underground coal mines across the United States. The purpose of this manuscript is to introduce the mining industry to a multi-methodological approach to safety culture assessments. Further, it is the goal of this manuscript to highlight the value of including both quantitative and qualitative methods into safety culture assessments in order to obtain the most comprehensive view of an organization?s safety culture. Because this manuscript focuses solely on the methodology implemented, data and results obtained during the five safety culture assessments will not be presented in this manuscript, but will appear in a future publication.

Feb 27, 2013

By M. R. Smith, H. Kanli

The impact crusher is a popular device for producing crushed aggregates from non-abrasive rocks such as limestones, offering the advantages of high reduction ratios and relatively low installed costs. To extend the application of a process-flowsheet simulator to the quarrying industry, a mathematical model of an impact crusher was therefore developed using the general crusher models of Andersen and Whiten as a basis

Aug 1, 1995

By S. J. Rodgers

This report presents guidelines on methods of dust control in conventional coal mining operations. The normal mining cycle and equipment used in a room and pillar conventional section are described. Main ventilation, section ventilation and face ventilation are discussed in detail. Proper installation of line brattice, maintenance of proper air flows at the face and split ventilation are stressed. The effects of maintaining the end of the line brattice near the face are described. The advantages and disadvantages of blowing and exhausting face ventilation are presented. The use of water sprays on cutter bars and loading machines is described. The design of a nonclogging water spray system developed under a Bureau of Mines contract is presented. Other methods of reducing dust exposure are discussed and include alternative procedures for shot firing and administrative controls.

Jan 1, 1983

A Process for the Flotation of Chrysocolla

Sep 13, 2010

By Kazuo Magata, Hirohiko Fujita, Masazumi Tashiro, Yoshiaki Sato, Yoshio Shinoda

The Shinkansen of the Japanese National Railways (JNR) presently in operation between Tokyo and Hakata, approximately 1,000 km, was constructed at three stages: between Tokyo and Shin-Osaka opening in 1964, Shin-Osaka and Okayama in 1972 and Okayama and Hakata in 1975. Works on the extension of 400 km from Okayama to Hakata were launched in March 1970. As construction of the undersea Shin-Kanmon Tunnel on the extension was the toughest task, requiring many, many months, the work was undertaken earlier than any other works on the extension. It was brought to its completion in June 1974 at the cost of about 22, 000 million yen. The Shin-Kanmon Tunnel is the third undersea tunnel constructed to connect the main island of Honshu and Kyushu across the Kanmon Straits. (Table 1)

Jan 1, 1976

By Arthur D. Silber

The economic success and growth of any metropolitan region depends on mobility. Today, mobility between New Jersey and New York is threatened by a transportation system that cannot meet 21st century travel demands. The transportation bottleneck created by the Hudson River threatens the viability of one of the world?s great centers of commerce and culture. Fortunately, there is a solution: The Access to the Region?s Core Mass Transit Tunnel. The US$8.7-billion Mass Tran-sit Tunnel?s (MTT) new two-track line will double commuter rail capacity under the Hudson and create a new, state-of-the-art cavern station in Midtown Manhattan, with wide platforms, high-speed escalators and other features to improve riders? travel experience. The capacity and other benefits of the MTT project will launch a new era of prosperity for the region, just as the Pennsylvania Railroad did almost 100 years ago when it built the existing two, single-track rail tunnels that now form the sole commuter rail link between New Jersey and New York. The existing tunnels run from North Bergen, NJ, under the Hudson River to Pennsylvania Station at 33rd Street in Manhattan. Construction on the MTT, the largest public works project in the United States, is scheduled to start this year and continue through 2017. The MTT is ready to go to construction thanks to a major commitment of financial, engineering, project management and other resources from NJ TRAN-SIT, New Jersey?s statewide mass transit agency, and the Port Authority of New York and New Jersey, a bistate agency that operates the Holland and Lincoln tunnels, the George Washington Bridge and other major transportation facilities in New York and New Jersey. The project is also strongly supported by the state governments of New York and New Jersey, as well as that of New York City. The MTT is New Jersey Governor Jon Corzine?s number one transportation priority.

Jan 1, 2009

By A van Jaarsveld

Environmentally-friendly, safe and cost-effective technology for stope drilling has successfully been introduced at TauTona mine. It has enabled the problem of inadequate compressed air pressure and its downgrading impact on production capability to be overcome. The paper traces the development process which culminated in the conversion of the entire stoping operation at TauTona to electric drilling. Background work which took place at other mines is also described. Statistics of performance improvements are provided. 1. Introduction Holman?s Silver series and the Seco S215 were drills that had a measurable impact on the South African gold mining industry. It is too soon to say whether Hilti will join those great names. However, there is no doubt that the introduction of electric drills into the harsh and unforgiving world of deep level gold mining is a significant development. History has shown that being the first to enter a new technology is no guarantee of long-term success. The pain and suffering which accompany the birth of anything new can deplete the energy of the innovator while at the same time creating opportunities for competitors to leapfrog him. In addition to commitment and enthusiasm, the innovator must therefore also possess, or have access to stamina and resourcefulness to overcome the unexpected difficulties which will inevitably arise. All of these were needed for the Hilti project.

Jan 1, 2008