Search Documents

By Christian Wawrzyniak

An analysis method for modeling compensation grouting based on the finite element method is presented. By this method the design parameters of compensation grouting, grouting pressure and grouting volume, can be evaluated. Also the subsidence of a building due to tunnel driving as well as the lifting of the building by compensation grouting can be simulated. The stress changes in the tunnel lining and in the foundation of the building are computed as well. The application of the analysis method is demonstrated on two examples for compensation grouting in combination with construction of tunnels.

By D Craw, D Wilson, D Chappell

Gold is extracted by cyanidation of a sulphide-rich concentrate at Macraes mine, and after cyanidation, the concentrate is discharged to tailings impoundments. The concentrate tailings were discharged to a dedicated concentrate impoundment from 1989 to 1993, afterwhich they were blended with the flotation tailings. Since mid-1998, concentrate tailings have been redirected to the dedicated concentrate impoundment. The concentrate tailings contain up to 1 ppm gold, and will be reprocessed in the future. However, it is a regulatory requirement that a contingency plan be in place to rehabilitate the concentrate tailings should the mine operation cease for any reason. Initial predictions suggested that the sulphide-rich tailings would oxidise and acidify, creating a potential long term environmental problem. Investigations of the state of the tailings after 4 years show that these predictions were overly conservative. Only minor oxidation has occurred in the upper 2 metres of the tailings where the pH has locally dropped from 10 (discharge condition) to between 7 and 8. Below 2 metres, the tailings are essentially unchanged from their deposition state. The low rate of change in the tailings is due to their very low permeability which in turn is a consequence of the fine grain size (ca. 15 ¦m). Dewatering is extremely slow, and incursion of oxygenated water is negligible. Calculations suggest that water movement over 30 m will take at least 100 years and possibly 1000 years. The contingency plan is to capitalise on the very low permeability and keep the tailings from drying with a semipermeable cap. A layer of limestone will be added to the top of the tailings, beneath the cap, to enhance alkalinity of any percolating water. If acidification does occur, contrary to expectations, any acid produced will be neutralised by underlying calcite-bearing schist, schist in the concentrate impoundment wall, and the flotation tailings immediately downstream. In addition, dilution by alkaline ground and surface waters would further ameliorate any acidic discharge.

Jan 1, 1998

By Gray Mullins

This paper presents experimental results from a study to assess the interface bond between a cast-in-place concrete seal slab and prestressed concrete piles in cofferdams. Three different seal slab placement conditions - fresh water, salt water and bentonite slurry - were evaluated and the results compared against controls where no fluid had to be displaced by the concrete. Normal pile surfaces were investigated. Additionally, the situation of ?soil caked? piles was also investigated. Both model and full-scale tests were conducted. In the model tests, twenty eight 15 cm square prestressed sections were used with the embedment depth varied between d-2d, where d is the width of the pile. In the full-scale tests, 16 specimens were tested. The prestressed piles were 36 cm square with the embedment varied between 0.5d-2d. Four of the sixteen piles were cast with embedded gages located at the top, middle and bottom of the interface region. The results showed that loads were transferred to the piles over an effective area, not the entire embedded depth. Significant bond stresses developed even for the worst placement condition. Recommendations are made for revising current values in specifications.

Jan 1, 2013

By B. Gazea, A. Kontopoulos, A. Kourtis, K. Adam

Static tests give a measure of the balance between acid-producing and acid-neutralising mineral components in a material, while kinetic tests determine acid generation and neutralisation over a long period. Drill-core samples from the amphibolite and gneiss host rocks of the Stratoni lead-zinc sulphide deposit in Greece and mine/mill waste samples from Stratoni and Olympias were examined by the standard acid base accounting, BCR and net acid production tests. Mineralogical data on the materials and resulting residues were used to illustrate the differences between the methods and establish their ranges of applicability. BCR seems to simulate most closely the conditions prevailing during generation of acid mine drainage but is time-consuming and requires elaborate equipment. Acid base accounting is suggested for standard screening; net acid production might be used in the field or for solids with less than 10% S

Jun 19, 1905

By Brian Isherwood

TransCanada Pipelines, Calgary (TCPL) is one of North America's leading transporters of natural gas through its energy transmission business. TransCanada also operates significant complementary businesses in energy marketing and energy processing in North America and internationally. The main trunk pipeline crossing Canada comprises as many as six pipes, 30" to 48" diameter delivering up to 7.8 trillion cubic feet of natural gas per day. To maintain the maximum operating pressure of 1000 psi, it is necessary to provide compressor stations at 60 to 100 km spacing. One such station is located at Potter, in northern Ontario, some 80 km north of Timmins, referred to as Station 102. The station contains two compressor plants, 'A' and 'B' Each incorporates a gas turbine driven centrifugal compressor unit. 'A' Plant uses an aero-derived gas generator (jet engine) rated at 15 MW (19,000 HP).

Jan 1, 1997

By J. R. Ross

Recovery of uranium from slightly alkaline mine water, available in the Ambrosia Lake district of New Mexico, was studied using countercurrent ion exchange columns developed by the Bureau of Mines. Approximately 5 million gallons of mine water containing 9 to 12 ppm U308 was treated by ion exchange using a 14-inch-diameter absorption column composed of five or six compartments each 4 feet deep. Uranium recoveries averaged in excess of 98 percent at solution flows ranging from 15 to 25 gallons per square foot per minute and resin loadings up to 3.6 pounds of U.08 per cubic foot. In subsequent tests, loaded resin was continuously eluted in a countercurrent elution column with a diameter of 4 inches and containing a bed of resin 9 feet deep. The resin was eluted to a residual loading of less than 0.06 pound of U305 per cubic foot, at a resin-retention time of 224 minutes, using only 1.9 volumes of 1.1 M NaCl-0.05 M NaHCO3 solution per volume of resin. Compared with existing ion exchange practices for recovering uranium from mine waters in the Ambrosia Lake district of New Mexico, use of these improved ion exchange contactors would reduce ion exchange resin requirements at least 70 percent and allow further substantial reductions in capital and operating costs.

Jan 1, 1971

By Wesley T. Holmes

This report describes the second phase of an investigation aimed at obtaining a wider knowledge of the problems involved in smelting titaniferous magnetites. Liquidus temperature measurements were made on selected synthetic slag compositions in the Ti02 -A1203 -FeO-Si02 -CaO-MgO system. Both the hot-stage microscope and the strip furnace (melting-holding-quenching technique) were used during test procedure to determine the effects of CaO, MgO, and SiO2 on the liquidus temperature of slags. The liquidus temperatures of slags studied ranged from 1,241° to 1,900° C. The lowest liquidus temperature for each Ti02 plus A1203 plus FeO weight-percent generally occurred when the difference between CaO plus MgO and Si02 was less than 12 weight-percent. In this investigation substitution of either CaO or MgO for SiO2 and MgO for CaO raised the liquidus temperature of more than 50 percent of the reported base slags when Ti02, A1203, and FeO contents were held constant. The results of this investigation may serve as guidelines for determining flux requirements in smelting a wide variety of titaniferous magnetite concentrates or ores.

Jan 1, 1968

By Wern-ping Chen

To mitigate and control the combined sewer over-flows from 17 outfalls in Detroit, MI, three outfalls in Dearborn Heights, MI and eight outfalls in Redford Township MI, the Detroit Water and Sewerage Department (DWSD) completed the preliminary design of a storage tunnel in 2005. In 2006, a final design revised the alignments and the inside diameter (ID) of the tunnel. The revised tunnel system includes an 11.28-km (7-mile) 9.14-m (30-ft) ID tunnel, a 24.4-m (80-ft) ID pump station, two work shafts about 15.2-m (50-ft) ID each and 14 drop shafts with various IDs. A small portion of combined sanitary and storm sewers serve the majority of the Rouge Valley water-shed. This includes Detroit, MI and most of the western suburbs. The Northwest Interceptor (NWI), that extends between Eight Mile Road and Ford Road and roughly parallel to the Rouge River, intercepts sanitary sewage and some wet weather flows from trunk sewers in the tributary areas for transport to the wastewater treatment plant (WWTP) for treatment. During extreme storm events, when the capacity of the NWI is exceeded, the excess combined sewer and overflow (CSO) over-flows into the Rouge River through 17 outfalls to local rivers. The purpose of the Upper Rouge Tunnel system (URT) is to capture and significantly reduce the uncontrolled CSO from these 17 outfalls in Detroit, three outfalls in Dearborn Heights and eight outfalls in Redford Township. When implemented, the

Jan 1, 2007

By Meghan McGrath

Third generation advance high strength steels with microstructures of acicular ferrite and retained austenite were investigated and meet mechanical property goals. A good combination of strength and ductility were achieved with duplex ferrite and austenite microstructures where cementite formation was suppressed. Transformation induced plasticity (TRIP) behavior produced rapid work hardening. The mechanical properties of two hot-rolled steels with duplex microstructures were compared and had the following compositions: (1) Fe-0.14C-13.87Mn-1.42Si-3.51Al; and (2) Fe-0.06C-14.2Mn-1.85Si-2.38Al. These steels were cast, homogenized, and hot rolled at 900ºC to obtain a refined microstructure with ultimate tensile strengths and elongations to failure of 865 MPa and 39% and 1,217 MPa and 28%, respectively. The amount of metastable austenite in both compositions decreased after tensile testing from 58% and 28% to 6% and 0%, respectively. Microstructures were characterized using optical microscopy, scanning electron microscopy (SEM), and x-ray diffraction.

Jan 1, 2010

By Dale Preece, Ayman Tawadrous

This paper presents a number of examples of three-dimensional blast modeling in both surface and underground environments that include time-delay explosive decking. These examples include: 1) quarry blasting, 2) coal seam protection blasting, 3) mineral mine blasting with high energy time delayed decks, and, 4) underground single-level/single-shot drawbell blasting.

Jan 1, 2014

By A Bax, G Wardell-Johnson, A Giblett, W Staunton

This paper presents a number of key considerations for process development testwork as a reliable basis for the inclusion of gravity separation in gold recovery flowsheets. Operating data, experiences and numerous case studies are also discussed in support of identifying best practice principles for gravity circuit design.CITATION:Giblett, A, Bax, A, Wardell-Johnson, G and Staunton, W, 2013. A review of best practice in gravity circuit design and operation, in Proceedings MetPlant 2013 , pp 272-284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By J. W. Bridge

Triaxial compression tests at various confining pressures and temperatures, as well as tangent modulus tests using ultrasonic waves, were conducted for wax-coated granular composite materials. The material used is a surface for Thoroughbred horse racing. The purpose of these tests is to examine how track shear strength and tangent modulus at a range of loads respond to changing temperatures. Previous work has shown that a wide range of operational temperatures are experienced which have been reproduced in the lab. Using differential scanning calorimetry, it is confirmed that these operational temperatures correspond to distinct thermal transition regions for the wax that is used to coat the sand in these surfaces. Preliminary results show that both shear strength and tangent modulus are sensitive to temperature changes with maximum strength and modulus correlating with major DSC wax transition regions.

Jan 1, 2010

By Brian T. Burch, Paul N. Worsey

When fired, submerged Linear Shaped Charges (LSCs) lose all effectiveness in the cutting of steel. Users in underwater applications have reported having to substantially increase the charge size to the point where brute explosive force shears rather than cuts the target.

Jan 1, 2015

By D. William Tedder

Several bauxite residue sands and muds produced by Bayer plants in the U.S. and overseas have been fractionated using dry and wet magnetic separators. The magnetic sand fractions typically contain about 60 wt% iron and the bulk of the radioactivity in this waste. The muds are more difficult to process than the sands, but some fractionation is possible using a combination of flotation and magnetic separation techniques.

Jan 1, 1984

By P. Roy

Smelting or converting of sulphide concentrates and mattes in a batch operation presents a challenge when directing the off- gas to a conventional acid plant. The Hindustan Zinc Ltd. (a division of the Vedanta Group of companies) Chanderia Lead Zinc smelter was presented with such a challenge that was met with the adoption of the Cansolv® SO2 Scrubbing System. The Ausmelt top submerged lance technology used at Hindustan Zinc generates a furnace gas stream that containsbetween 0.1 vol% and 12 vol% SO2 during the three stages of batch smelting. Cansolv® SO2 Scrubbing Technology captures the SO2 to ensure that treated flue gas exits the facility at a concentration below 100 ppmv SO2 and it releases SO2 in a controlled fashion, to more closely match the needs of the existing acid plant. The application of a regenerable scrubbing system to capture SO2 from a batch-operated furnace and convert it to acid in a conventional acid plant was a first of its kind in the world. This paper provides an update on the design and operation of the Hindustan Zinc SO2 recovery system and suggests two improvements to the basic flow sheet that optimize the cost of SO2 scrubbing further.

Jan 1, 2007

By K. Rainer Massarsch, Bengt H. Fellenius

"Abstract Vibration limits for buildings with respect to ground vibrations from pile driving published in international standards are reviewed. At first, relevant vibration parameters are defined and the evaluation of vibration records is described. The sensitivity of structures to different vibration parameters (displacement, velocity and acceleration) is discussed. Most vibration standards relate to blasting activities, the dynamic characteristics of which can be significantly different to those from construction activities and in particular, pile driving. Several vibration standards are reviewed. The Swedish vibration standard is described in detail, as it is the only one accounting for several important factors, such as ground conditions, building material, and type of building foundation. Many standards limit the guidance to values based on the dominant vibration frequency and a wide scatter of frequency-dependent vibration limits exists. It is difficult to compare limiting values of ground vibrations proposed in different standards.1. INTRODUCTIONFor poor ground conditions, placing structures on piles is the most common foundation solution, while sheet piles are widely used to support deep excavations. Piles and sheet piles must often be installed in the close vicinity to buildings, structures or installations in the ground, which can be affected by ground movements and vibrations, (Massarsch and Fellenius, 2014). In many areas, environmental concerns with respect to noise and ground vibrations can restrict or even prohibit driving of piles or sheet piles or reduce the efficiency of installation. The design engineer must prescribe – often at an early stage of a project — the permissible levels of ground vibrations in order to minimize the potential risk of building damage. When seeking guidance from the literature, little or practically no applicable information can be found on how to assess permissible levels of ground vibrations."

Jan 1, 2014

By Munro P. D

Eh-pH measurements were taken on an industrial zinc reverse flotation process at Brunswick Mining and Smelting Corporation Limited. Laboratory zinc reverse flotation testwork on samples of the feed to the industrial process produced Eh-pH data which were similar to the data from the industrial process.Later, the Eh-pH data from the industrial process were compared with data from a pilot plant scale zinc reverse flotation process at Mount Isa Mines Limited. After comparison with the data from Brunswick Mining and Smelting Corporation, deficiencies in the pilot plant Eh-pH data could be recognised and corrective actions were taken for the pilot plant. A robust pilot plant zinc reverse flotation process was obtained with consistent performance at the expected level.The implications of these findings for a range of processes are also discussed.

Jan 1, 1988

By Patrick J. Hannigan

A comparison of 40 statically and dynamically load tested piles was performed to evaluate the variation between testing methods. This evaluation indicated an agreement of 10% to 15% could be obtained when the available static resistance is fully mobilized by both methods and when time dependent capacity changes are minimized. Dynamic pile testing recommendations for minimum induced impact force, ram weight to pile weight ratio, and considerations for time dependent capacity changes are presented.

Jan 1, 1987

Valuable Components Recovery from Lead-Zinc Metallurgical Slag

Sep 13, 2010

In a gravity separation device, particle shape, size and density all play a role. The combination of these determines where each individual particle reports to in the viscous fluid, where particle crowding (solids to water ratio) also plays a role. To understand the performance of gravity separation devices in the heavy mineral industry, these particle characteristics need to be measured. There are various challenges in analysing particle density and particle size simultaneously for the purpose of quantifying gravity separator performance, not to mention particle shape. These analytical challenges include the high cost of high-density sink-float fractionation, toxicity of high-density sink-float media, inability of sink-float media to fractionate at densities greater than 4.0 g/cm3, and the time-intensive nature of these fractionations. The use of the detailed particle-by-particle output from Qemscan® particle mineral analyses (PMA) as a fast and cost-effective alternative is evaluated. The size and density outputs from the Qemscan® were employed to characterize the performance of a heavy mineral spiral concentrator as an example. Critical analytical requirements are to be addressed before the Qemscan® output data can be utilized. Keywords Gravity separator, performance, heavy minerals, Qemscan® particle mineral analysis

Jan 1, 2011