Search Documents

By M. A. Trevits

The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate, improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Since wood is the second most abundant fuel available during a coal mine fire, it was decided that series of large-scale wood crib fire tests were needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.

Jan 1, 2009

By Tano Balbin, Valery Astakhov, Juha Timperi, Lauri Koresaar

"Online elemental analysis is the basis of optimal flotation control in mineral concentrator plants. Traditionally XRF analyzers have been used as the online analysis method. However, online XRF analyzers struggle to measure elements below calcium in atomic number (Z=20). For many processes lighter element assays would be beneficial to improve control of grade and recovery. Processes where elements below Ca are required include P, Mg and Si in phosphate concentrators, Si, Mg and Al in iron concentrators, and S and C in gold concentrators. Laser-Induced Breakdown Spectroscopy (LIBS) based elemental analysis can readily be applied to these processes. LIBS is based on generating plasma in the slurry sample by a high energy laser and analysis of the plasma by optical emission spectroscopy. Capabilities of a new Courier® 8 analyzer based in LIBS technology are demonstrated for elemental analysis starting from lithium (Z=3). Results of a plant installation in a sulfide gold concentrator provide a good agreement with the analyzer and laboratory assays.IntroductionEffective process control can be regarded as one of the fastest paying investments for a mineral processing plant. Process optimization in flotation circuits requires constant feedback of the process state. If only manual laboratory samples are available, this optimization becomes difficult due to the long delay between taking the sample and acquiring the laboratory result. If the element grades are available in online basis, the operator or automatic process control system can make corrective actions in real time.Online X-Ray Fluorescence (XRF) analyzers have been in use at concentrators for decades. The XRF analyzers can provide a fast, accurate and precise analysis from slurry streams. However, the drawback of XRF analyzers is their lack of capability to measure elements below Ca (Z=20) in atomic number. The low energy X-rays of the low atomic number elements get absorbed by water in the sample, protective window of the analyzer, or air between the sample and spectrometer."

Jan 1, 2017

By W. Smith

The U.S. Bureau of Mines (USBM) is using laboratory and computer-based techniques to investigate the post- failure behavior of yielding pillars and pillar reinforcement techniques to control entry deformation. Poorly dimensioned yield pillars, can cause adverse ground conditions. Laboratory studies to evaluate various reinforcement techniques for controlling yield pillar deformation were conducted. A cracking and crushing model is used to evaluate potential tensile and compressive failure planes within pillars of various widths to assess the degree of yielding and stress redistribution. The use of an elasto-plastic model to evaluate the effect of various reinforcement on yield pillars is also discussed. These procedures effectively account for the residual pillar strength, important in yield pillar design.

Jan 1, 1995

By Gordon King

The City of Atlanta Water Department required the construction of a two sludge tanks and a wet well at the existing Chattahoochee Water Treatment Plant. Western Summit won a design build contract to build the project and proceeded to evaluate the wet well size options, and construction procedures. The final design required the construction of a 1 million gallon tank. The proximity of the underground tank to adjacent roads and existing plant structures ruled out laying back the excavation. As a result a tied back sheet pile retaining wall was initially proposed.

Jan 1, 2003

By Linli Wu

During the measurement of contact angle, a misty band was observed near the substrate. Hsien-Nan Ho and Shinn-Tyan Wu thought this was because the oxygen atoms on the interface migrate to the droplet surface to form an oxide band near the substrate. But from our experiments misty band appeared before the drop reach to the substrate. Theoretically speaking, the oxygen partial was the same everywhere in the vacuum furnace. So there was no condition to provide enough oxygen forming oxide. This appearance would be explained more reasonably with the optics principle. Most reflected light would be absorbed by the substrate and the light cannot reach the observation area, so the misty band formed.

Jan 1, 2006

A Special General Meeting of the Institute was held in Kelvin House, Johannesburg on Wednesday, 29th September, 1971. The President, Prof. D. D. Howat opened the meeting at 9.55 a.m. The President read the notice of meeting which was as follows: "In order to bring industry into closer liaison with the work of your Institute and to place the Institute's finances on a sound basis your Council recommends that companies be admitted to membership of the Institute under clause 2.6 of the Constitution, that is, as Non-Corporate members. The designation for this class of member will be that of "Company Affiliate". 2 Membership: This clause to be amended as follows:- 2.6 "Non-Corporate members shall comprise the grades of:- Company Affiliate Honorary Fellow Graduate Associate Student" 2.6.1 This clause to be added:- "Companies involved in or associated with the mining or metallurgical industries are eligible to become company affiliates" 2.14 Add:- "A special certificate shall be issued to all company affiliates". After giving the background to the recommendation made by Council the President asked for a proposer and seconder for the resolution. Mr J. K. E. Douglas proposed and Mr D. G. Maxwell seconded the resolution. The meeting agreed that the constitution be amended as proposed. The meeting closed as 10.05 a.m.

THE nature of the ore deposit of the Broken Hill line of lode is such that it can be broadly divided into two the calcitic and siliceous ore bodies. The principal minerals occurring in these ores are: Galena, sphalerite, pyrite, arsenopyrite, chalcopyrite, pyrrhotite, calcite, rhodonite, garnets, feldspar, fluospar, quartz.Whilst these minerals persist in both classes of ore, the following typical analyses of Broken Hill South Limited ore bodies will give some indication of the disposition with regard to each:

Jan 1, 1928

By Nick D. Rose

The importance of structural geology in open pit slope stability is overlooked in many mining operations due to pressures to cut costs and minimize mine personnel. As a result, mine geology staff are often unable to keep up with geological mapping of the pit slopes due to other day to day production oriented tasks. In some instances, key structural controls that contribute to slope instability may not be identified until after a slope instability has initiated, at which time it may be difficult or impossible to delineate these features in the field. Even for small slopes, understanding the engineering and structural geology of the rock mass, as well as the effects of groundwater and blasting practices, are of key importance to slope stability. Two case histories are presented as examples of mining operations that experienced slope instability with little more than anecdotal information about the structural and groundwater conditions encountered during mining. By conducting field reconnaissance, simple slope stability analyses and ongoing slope monitoring, practical remedial measures were implemented, allowing continued safe mining operation.

May 1, 2002

Rehabilitation, reclamation and restoration are all terms used to describe the repair of land after mining. Here, restoration is used to mean restoring the land's original use, capability or productivity. Effective restoration is dependent on good planning before mining commences and must include a clear definition of post-mining objectives. The physical condition of the land within the mining licence was that of an imperfectly drained soil in permanent pasture, supporting a seasonal supply dairying unit. During the mining process, the soil layers were separated, with the topsoil stockpiled separately. As part of the restoration process, the land was recontoured to encourage surface drainage, with topsoil spread evenly over the recontoured tailings. Low grond pressure machinery was used to minimise soil compaction, with light discing and harrowing used to increase water infiltration. A permanent pasture was sown, with weed species controlled by spraying, both before and after pasture establishment.  Soil testing has been used extensively to ensure there were no nutrient deficiencies that good compromise pasture establishment and performance. Controlled grazing practices were used to ensure that the sown pastures became well established.

Jan 1, 1998

By Taegong Ryu

A thermal plasma process was used to synthesize nanosized tungsten carbide -cobalt composite powder, in which ammonium paratungstate and cobalt oxide were reacted with a gas mixture containing CH4, H2 and Ar. The reduction and carburization of vaporized precursors produced nanosized tungsten carbide (WC1-x) - cobalt composite powder, which sometimes contained small amounts of W2C and/or W phase. The effects of gas composition, plasma torch power, and the flow rate of plasma gas on the product composition and grain size were investigated. The grain size of synthesized tungsten carbide powder was less than 20 nm. The synthesized composite powders were also subjected to a hydrogen heat treatment to fully carburize WC1-x, W2C, and W phases to the WC phase as well as to remove excess carbon in the product. Finally nanosized WC-Co composite powder of grain size less than 50 nm was obtained.

Jan 1, 2009

By J. Moyes

The Intec Process is a generic process for the production of pure base metals and precious metals from sulphides concentrates derived from copper, nickel, zinc and lead ores. The development program for the Intec Process initially focussed on the treatment of copper concentrates, (the ?Intec Copper Process?), and more recently of zinc concentrates, (?the Intec Zinc Process?). Developed and proven in Sydney, Australia at a cost of US$15m over the last ten years, the Intec Copper Process is now ready for commercial application. The knowledge gained during the development of the Intec Copper Process has been applied to the Intec Zinc Process, which utilises the same basic chemistry to produce high purity zinc ingot from metallurgically complex zinc sulphide concentrates containing lead, copper, iron, silver and gold. The demonstrated ability of the Intec Zinc Process to treat low grade mixed zinc/lead/copper concentrates, including those with high iron and manganese levels, holds out the real prospect of overcoming major metallurgical hurdles that have long affected the zinc industry. The Intec Zinc Process consists of the three consecutive circuits of leaching, purification and electrowinning. The leach circuit is of single stage configuration with a series of reactors to which concentrate and lixiviant are fed. Purification consists of cementation and precipitation by pH adjustment. Electrowinning employs an electrolytic cell very similar in design to that of the Intec Copper Process, but differs in that a conventional plate cathode is produced. During electrowinning, the same mixed halide species (BrCl2 -, HalexTM) that is integral to the Intec Copper Process is generated in solution at the anode and exhibits powerful leaching characteristics capable of directly leaching the sulphide concentrate feed. The need to roast the concentrate prior to leaching, as is practised in the conventional Roast/Leach/Electrowin (RLE) process, is thus eliminated whilst a range of by-products (notably lead, copper and precious metals) can be extracted in the simple, single-stage leach. This paper describes the Intec Zinc Process; the technology, predicted economics and its environmental aspects.

May 1, 2002

By R B. Stewart

Where pasture production is the intended land use of the areas to be reclaimed, the creation of a suitable growing +medium is a major objective. To achieve this land reclaimers require a sound understanding of the proposed mining plan and a knowledge of the physical, biological and chemical properties of materials intended for resurfacing disturbed areas. Where the original soil is not being replaced in its natural state, research is usually required to determine an alternative growing medium. Results from field research conducted on waste material from the Waihi Gold mine are reported with emphasis on the significance of soil depth in relation to pasture production in this environment.  Problems in extrapolating field research to large scale operations are also considered.   Essentially the requirements for successful pasture production, on surrogate growing medium, are akin to conventional approaches used in New Zealand in the development of unimproved agricultural land. High inputs of fertiliser are initially needed, especially where volcanic soil is used, and careful management of pastures and soils is required to minimise soil erosion and create a sustainable system. In the first three to five years of pasture production, grazing use of the land requires to be dictated by pasture availability and soil conditions and not by animal feed requirements. The use of light stock (young dairy or sheep) is recommended.   Successful land restoration requires a team approach by a range of cooperative specialists including engineers, soil scientists, farm managers, agricultural contractors, landscape architects and environmental officers.

Jan 1, 1991

The Australian mining industry is at an interesting stage in its development. Of the large number of mining companies in Australia, some are still solely domestic in their focus, others have made their first tentative forays offshore, and others are global players of significance in tile world industry.   It is not long ago that the entire industry was almost exclusively domestic in its focus. Very few companies before the early 1980s had ventured offshore, and those that did so were considered quite risque. The initial moves were made mainly by large companies who could afford to lose the funds expended in getting started in a range of offshore locations.   Almost all offshore jurisdictions were considered to be high risk compared to the safety of home - I recall the extreme difficulty I encountered in the mid 1980s in endeavouring to persuade a Board to joint venture into an attractive gold opportunity in South East Asia.   One of the problems inhibiting the offshore development of the Australian mining industry was that some mining companies had had unfortunate experiences offshore. Others had heard of those who had had unfortunate experiences offshore and, as such, 'offshore' gained a bad name and the more risk averse boards and. management of the time simply put the whole idea into the 'too hard' basket.

Jan 1, 1995

By F. M. Vokes, P. M. Ihlen

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Ore deposition was related to three major stages: continental rifting and separation (Vendian-Late Cambrian), convergence (Late Cambrian-Early Silurian) and collision (Early Silurian-Devonian). The first stage included deposition of volcanogenic massive sulphide Zn-Cu and stratabound or stratiform Fe and Zn-Pb(-Cu) on continental margins, as well as less economic Nb and Fe in carbonatites, U, Mo, Ni and V in Alum Shales and orthomagmatic Cr, Fe-Ti and Ni(-Cu). The numerous volcanogenic massive sulphides formed during convergence included Early Ordovician Cu-Zn, mature-arc Cu, Zn, Pb and Fe-oxide deposits, Besshi-type deposits dominated by Cu or Zn in gabbro-intruded sediments and minor Cu-Ni(-PGE), Cu-Mo and skarn deposits. The collisional stage is represented by epigenetic deposits including sandstone Pb deposits (Pb, Zn, Ba, F and Cu) and minor vein deposits with variable Au, Ag, Pb, Cu, Zn, Fe, As, Sb, W and Mo

Jun 19, 1905

By R. Hipsley, D. Arbonies, P. Dobak

South Arturo is a “Carlin-type”, breccia-hosted, oxide gold deposit located at the north end of the Carlin Trend. The discovery hole was drilled in July 2005 from mine dumps 1,000 feet south of the Dee open pit. Discovery hole (BD-72) encountered a cumulative 245 feet @ 0.056 opt Au beneath 850 feet of post mineral Tertiary Carlin Formation. Oxidation extends to depths greater than 2,000 feet in the deposit area. The deposit is presently in definition drilling stage with approximately 190,000 feet of drilling completed to date. A resource estimate is in progress. This paper will focus on the discovery and descriptive characteristics of the mineralization.

Jan 1, 2007

A number of impending and actual pit wall failures have been observed and documented, which have been interpreted to initiate on newly generated structural features. This infers failure through intact rock. Failure mechanisms have been postulated resulting from circumferential stress, extensional strain and brittle flexure. These will be discussed in the context of the failures and the associated monitoring. The implications of failure initiating on ?unknown? features has a significant impact for deep open pit mines where designs are based on the expected structural regime. Being able to anticipate such failures is important for design. Equally important is management of such changes as they arise. In this context, monitoring using high resolution microseismic techniques will be discussed as a means of providing early warning of such failures.

Jan 1, 2006

By F. R. Koeberlin

ABOUT thirty miles south of the port of Coquimbo, Chile, nestling in one of the western outliers of the main Andes range, lies the little mining town of Andacollo, a place whose history and traditions make up one of the most romantic pages in the life story of this southern republic. The beginning of Andacollo is shrouded in the penumbra of the pre-Columbian era, but its first mining activity probably dates from about the years 1440 to 1460. It was in the middle of the fifteenth century that the Inca Tupac-Yupanqui, grandfather of Atahualpa, conquered this part of Chile. His domain extended even as far south as the present site of Santiago, and perhaps farther, but was maintained with increasing difficulty against the fiercely independent and indomitable tribes of Araucanian Indians of the South.

Jan 1, 1938

By John R. Bartels

This U.S. Bureau of Mines report describes the development, system by system evaluation, and preliminary surface testing of a flywheel-powered shuttle car (FPSC). The use of a self-contained flywheel-power source has the potential to eliminate the numerous safety and routing problems associated with tethered mobile equipment. An alternative to conventional power cable systems was developed consisting of the world's fIrst seven-rotor stacked flywheel system capable of storing 6 kW·h of energy at 16,700 rpm. Numerous interdependent systems were necessary for successful interfacing with a conventional shuttle car. Each of these systems was evaluated and tested individually. Finally, the entire shuttle car was surface tested. The tests indicated that the flywheel energy system can function and operate a shuttle car. The economics of the system and the design of required support systems were not addressed in the project.

Jan 1, 1991

By Feng Yongxuan

Anchored sheep pile is normally used in deep excavations, many of which only require stability in accordance with Terzaghi theory. In this paper, based on the experience, new lateral earth pressure method is adopted taking account into interaction among soil, anchors and sheet piles so that a group for the project under very difficult conditions and very severe requirments, especially, for the displacements are determined according to that mentioned above. During and after construction, displacements monitoring were carried out for about four months, which was proved that there was a little difference between calculation and practice.

Jan 1, 1991

By Ö. Erdem

The investment decision making process in the insurance and finance industries is affected by new advances such as simulation techniques. These advances have improved the discounted cash flow method (DCF). In DCF, a dynamic and flexible model construction is not possible because it does not consider uncertain conditions. Each project should be evaluated taking into account the related uncertainties because the related uncertainties determine the characterization of the project. Related uncertainties can be processed in dynamic DCF, which is applicable to both financial and non-financial industries with different kind of uncertainties, such as power generation and petroleum projects. The dynamic DCF method can estimate net present value (NPV) while managing related project uncertainties with a simulation method like Monte Carlo Simulation. The simulation method is preferred because its output is unbiased. Therefore, a more realistic financial evaluation of the project can be concluded. In spite of the improvement of dynamic DCF, this project evaluation method is not used frequently in mining industry. However, the mining industry is ideally suited to this concept because it is highly dependent on estimations such as orebody size and ore grade. During the project evaluation stage, these uncertainties can be included with the dynamic DCF method. This study aims to contribute to increasing the usage of this method in mining projects. A copper reserve in Turkey is selected as a case study to apply uncertainty assessment for the evaluation of NPV.

Jan 1, 2012