Search Documents

Notwithstanding full concurrence with the dictum of a famous scientist that "definitions are the most accursed of all things on the face of the earth," in view of the considerable confusion which exists in jigging nomenclature, it is considered advisable to commence this paper with the following explanations of the terms which will be used throughout the text.Jig Bed. The whole layer of material lying on top of the jig screen.Ragging. The layer of denser material lying immediately above the jig screen, which is too coarse to pass through this screen and is confined horizontally by the cells of the top grid.Ore Column. The layer of ore pulp between the ragging and the top-water.Top Water. The water, carrying fine material in suspension, which flOiWS over the surface of the jig bed.Hutch Water. The water added to the jig below the screen. (Except for the water discharged with the hutch concentrate, the "hutch-water" eventually becomes "top-water.")Feed Water. The water in the ore pulp fed to the jig.(This water becomes part of the "top-water.")Pulsion. The period of the jigging cycle during which the water is moving upwards relative to the particles in the jig bed.

Jan 1, 1937

By G. Beghi, G. Piatti

THE authors examined the problem of the gradual transformation of Al2O3 from the transition phases normally encountered in SAP (r -x-n)1-3 to the stable a phase. This phenomenon is well-known at temperatures above the melting point of aluminum,3"6 whereas in this paper the transformation was studied at temperatures lower than the melting point of the aluminum matrix.

Jan 1, 1967

By Louis C. Brichta

The rapid depletion of known deposits of high-grade ore and the need for development of additional reserves, together with increased interest in open-pit mining of low-grade zinc-lead ores in the Tri-State District, led the Bureau of Mines to examine likely mining sites. Underground operations failed to remove all of the ore in a number of areas, and it appeared possible that some of them might be reworked successfully by low-cost open-pit methods. The South Carthage or Hull tract in Jasper County, Mo., was selected by Bureau engineers as favorable for the development of an open-pit mine.

Jan 1, 1949

By William I. Busenbark, Elmer C. Newman

At Bingham Canyon, the world's largest open-pit copper mine, annual grease consumption is in the neighborhood of 109 000 kg (240,000 lb), all of which was 544 (120-16) purchased, warehoused, and distributed in 54-kg (120-1b) and 180-kg (400-1b) drums. While perhaps a menial and mundane chore, grease distribution shows on the ledger as a significant expense item. To improve labor and cost performance, Kennecott maintenance engineers undertook a study to find the most direct method for moving multi purpose grease (MPG) from the refinery to the point of final consumption. What they found was a direct vendor system for hulk grease so simple and flexible that long-established drum distribution is being phased out in favor of the newer method throughout 75% of the operation.

Jan 9, 1977

By D. Nyungu

Despite observations of spalling and damage of mine excavation wall rock in the Bushveld Complex (BC) over the passage of time, there have been very few time-dependent or creep tests carried out in South Africa on rock, particularly on BC rock types. The research described in this paper deals with the investigation of stress and strain conditions influencing spalling of wall rock in BC mine excavations, and the influence of time on the tensile strength of several BC rock types. Time-dependent laboratory testing of BC rocks was carried out in indirect tension. The results show that the magnitude of the tensile strength of BC rock types is approximately 5% of their uniaxial compressive strength magnitudes. The average long-term uniaxial compressive strength of the BC rocks, interpreted from the axial stress-volumetric strain graphs, is 56% of the UCS value. The long-term tensile strength is shown to be less than 70% of the normal tensile strength. Extension strains at tensile strength failure ranged between 0.16 and 0.21 millistrain. Values corresponding with the long-term tensile strength are less than 70% of this range, namely, 0.11 to 0.15 millistrain. These results represent new knowledge, since such rock testing and analysis does not appear to have been carried out previously on BC rock types. Elastic numerical modelling was carried out to illustrate the extents of tensile stress zones and extension zones around of typical BC mine excavations. The models showed that large zones of extension strain can occur around BC excavations, and that the magnitudes of the extension strain can substantially exceed the critical values determined from the laboratory testing. The implication of this is that there are substantial zones surrounding BC mine excavations that will be prone to time-dependent spalling conditions and perhaps more significant failure.

Jan 1, 2014

By Eder Salazar

Como parte del desarrollo de sus operaciones de mina de cobre subterránea, la Sociedad Minera El Brocal S.A., desarrolló el método de minado tajeo por subniveles con pilares recorridas con el fin de incrementar su producción actual. En ese sentido, el presente texto señala la implementación de un método de minado conforme a las características geomecánicas del macizo rocoso del yacimiento.

Sep 12, 2011

By Rapheal Trousselle

For over 5 years, Davey Bickford has been developing and testing an electronic detonator blasting system. These new-technology detonators provide more accurate timing than conventional systems that rely on the combustion speed of a pyrotechnic composition.

Jan 1, 1997

By Hubert E. Risser

Although, for about a half-century the percentage of coal production provided through strip mining has steadily increased, recent trends indicate that a peak in percentage (not tonnage) is being approached, principally because of the decline in economic adrantage enjoyed by strip mining compared to underground mining. Factors contributing to the decline are the decrease in the margin of advantage in manpower requirements held by strip mining; an increase in depth and volume of overhurden, requiring larger equipment and capital investment; increasing lack of reserve land blocks large enough to support extensive strip mining operations; more stringent legislation for reclamation of stripped land, with increasingly higher costs of such reclamation; and the increasing costs of land surface rights for strip mining. Already there has been a peak and suhsequent decline in relative importance of strip mining insome major Eastern coal-producing states; trends indicate that a peaking for the whole Eastern region is on the way. Although, in the West the pressures are less severe, they will, nevertheless, reduce to an increasing degree the advantage that strip mining has possessed. For about half a century, strip mining has been providing an ever-increasing share of total coal output in the United States, and in the past 30 years this share has grown from less than 8% to 33.7%, as shown in Fig. 1. Fig. 1 also shows that strip mining is gaining faster in the West than in the East. From 1961 to 1967, output from strip mines grew 63.6 million toqs, or 52.2%. Certainly there is nothing in such performance to indicate any peaking in the level of strip coal-mine production. But the fact is that, if not in actual tonnage, strip mining appears to be reaching its peak in relative importance, at least east of the Mississippi River. And the area east of the Mississippi provides 90.0% of the strip and 94.9% of the total coal production of the nation. The relative economic advantage which spurred strip mining's growth for a third of a century has been diminishing markedly in recent years. Fig. 2 shows evidence of this decline. From 1947 until 1961, strip tonnage output remained fairly stable, at the end of the period showing only a 12.5% decline. Meanwhile, underground coal production fell 44.5%. As the result of the greater decline in underground coal, strip coal in 1961 furnished 30.3% of the total coal produced, compared to only 22.1% in 1947. In the succeeding six years, however, underground coal output increased by 76.5 million tons, while strip output increased only 63.6 million. Further evidence of the strengthening of underground coal's relative position — or if you will, the weakening of strip coal's position — can be found in the major coal stripping states: Illinois, West Kentucky, Ohio, Pennsylvania, Indiana, and West Virginia, which in 1966 provided 80% of the nation's strip coal. Fig. 3 shows what has been happening in three states lying in the Appalachian field and in the total output of these three states. In the figure, the column height represents the output of coal mined by all methods. The number at the base of each column is the percentage mined by stripping. In Pennsylvania and Ohio, the percentage of strip mining increased between 1956 and 1961, but by 1966 had declined from the 1961 level. In West Virginia, a decline occurred during the first five years but was followed by a rise. In January 1968, Coal Age published an article listing the locations and capacities of new large mines in the planning and construction stages that would be operating by 1968-1971. The plans for West Virginia and Pennsylvania indicated all the new mines would be underground. Except to the extent they might replace existing under-

Jan 1, 1970

By James J. Scott

Eleven workshops were held in various locations throughout the country in an attempt to reach the many diverse groups working in various mineral commodity areas and special ties. These meetings were held between March 1, 1974 and June 25, 1975. They were held under the auspices of the Bureau of Mines Contract to the University of Missouri-Rolla which was designed to help define Bureau research and development priorities. At each workshop a summary of current Bureau research and development was presented and the attendees were asked to present their ideas on what Research and Development programs should be undertaken to meet their needs locally. Participants included representatives of federal and state agencies, educational institutions, mining companies, equipment companies and other interested parties. The workshops covered under this report include lead mining in Missouri, limestone mining, coal mining both surface and underground in the midwest and in the Rocky Mountain area, iron mining in Minnesota, two top management meetings on institutional problems and, finally, a special two-day meeting on roof control.

Jan 1, 1977

Significant advances have been made in the design of centrifugal slurry pumps that are used for pumping high-density viscous and paste slurries. This paper presents the results of a series of centrifugal pump performance tests that were conducted using an FLSmidth 6 x 4 Krebs millMAX centrifugal pump. The pump was fitted with a dry mechanical seal to prevent dilution of the slurry from gland service water, as the theology of the slurry is sensitive to small changes in slurry density. Tests were done using paste kaolin slurry with Bingham yield stress values between 578-1 120 Pa and plastic viscosities between 728 and 1491 mPa.s. The viscous properties of the paste during each pump test were measured using a rotational viscometer. Pump head and efficiency de-rating were measured and compared to the correlations of Walker and Goulas (1984). The test data shows the pump's best-efficiency point (BEP) changes and shifts to the left of the performance curve. The pump efficiency decreases as the slurry yield stress increases. The head de-rating data shows more head de-rating at the low flow rates compared to the high flow rates for the high viscosity slurry, which is in line with the findings of Walker and Goulas (1984). This paper demonstrates that it is possible to pump very viscous, high yield stress slurries with limited head and efficiency de-rating using centrifugal pumps, provided that positive suction conditions are maintained at all times.

Jan 1, 2012

By J. Utt

Recent developments in circulating fluidized bed (CFB) once-through supercritical technology (OTSC) have enabled this technology to be offered as a utility-scale alternative competing head-to-head with pulverized fuel (PF) OTSC offerings. One clear example is the CFB supercritical unit at the Lagisza Power Plant in Poland, owned by PoludniowyKoncernEnergetyczny SA (PKE). This unit has now been in commercial operation for three full years, exhibiting very good performance, and has validated Foster Wheeler?s performance model at this utility scale as well as for units in the 600 MWe and 800 MWe size ranges offering net efficiency of ~43 per cent (LHV basis). This operating unit has also proven the use of the world?s first FW/BENSON? vertical-tube OTSC low mass flux technology. Since the Lagisza original international tender specified OTSC PF technology, it is important to note that the alternative selection of CFB OTSC technology over conventional PF technology is of historic significance, not only for the validation of the CFB supercritical platform as a viable alternative to conventional PF technology, but it also positions the CFB OTSC with fuel flexibility for offering of sizes up to and including 800 MWe units. This paper explores the differences between CFB OTSC technology and standard PF OTSC in utility power generation. Selection criteria, fuel burning range in both technologies, and other selection drivers are discussed. Economic analysis of both technologies, based on existing cases, is also provided. Also discussed are the technical advantages and uses of each technology. Foster Wheeler has recently been awarded a contract for four units of CFB OTSC technology, which utilizes a 2 on 1 configuration of two 550 MWe CFB OTSC boilers on two single 1000 MWe turbines. Essentially this provides a fuel-flexible low-emissions alternative to a 2 × 1000 MWe solid fuel power block.

Jan 1, 2012

By Fawad S. Niazi

Ever since the use of the cone penetration test (CPT) in geotechnical practice, attempts have been made to correlate CPT parameters with pile capacity components of unit end bearing (qb) and unit shaft resistance (fp), thus deriving multiple CPT-based pile design methods. These methods focus on "capacity" only without consideration to complete axial pile load-displacement (Q-w) response. Estimated capacities from these methods also exhibit considerable scatter without any consensus on their consistency. In addition, load-displacement curves obtained from axial load tests on highly expensive and extensively instrumented piles can exhibit different shapes. Nevertheless, a single value from the curve so obtained dictates the design capacity. Currently, there are at least 42 different criteria defining capacity with considerable variation in the values obtained thereof. The Randolph elastic solution, which provides a framework for analytical evaluation of pile load-displacement response, requires the profiles of soil stiffness. The fundamental soil stiffness defined by the small-strain shear modulus (Gmax) can be obtained from shear wave velocity (Vs) readings via seismic piezocone tests (SCPTu). The secant stiffness (G), which softens from Gmax corresponding to operational load levels, can be obtained by generating stiffness reduction curves from back analysis of load tests. Then, using appropriate G values, the Q-w curve can be defined for conditions similar to the database from the pseudo strain (w/d). Thus, a complete framework for optimal integration of SCPTu data, Randolph elastic solution and back-analysis of field operational stiffness can be established for complete axial pile foundation analysis.

Jan 1, 2011

By Y Zhang, X Yi, J Deng, J Zhao, J Song

To obtain the combustion process of a coal fire, a high-temperature programmed system is used to simulate the spontaneous combustion process of fresh and weathered coals. Both fresh coal and weathered coals from Liulingou, Inner Mongolia, China, were used to examine the gas releases from constant temperature to 650°C. Moreover, gas release rate was used to calculate the characteristic temperatures. The results showed the coal samples lasted to oxidise under high temperatures, and released plenty of heat to assist self-heating. The humic acid contained inside the weathered coal went through thermal decomposition as temperature rising and generated gases. This resulted in increasing concentrations of CO, CO2, CH4, C2H4, and C2H6. Changes of CH4, C2H4, and C2H6 gases were also similar. For weathered coal, concentrations of three gases were kept in balance under low temperatures, increased rapidly with the temperature rising. After the ignition temperature, the concentration of hydrocarbon was reduced. In addition, particle size affected coal spontaneous combustion. Coal samples with less than 0.9 mm in size produced much more CO than others. This study has examined coal spontaneous combustion caused by coal weathering during mining and its impacts on self-heating and pyrolysis in the process.CITATION:Deng, J, Song, J, Zhao, J, Zhang, Y, Yi, X and Zhang, Y, 2017. Gaseous products of weathered coal during the process of spontaneous combustion, in Proceedings Australian Mine Vent Conference 2017, pp 79–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

This paper reviews the manpower requirements of the Australian mining industry. It has been necessary to provide general background information in order to support the view that university education in mining and mineral process engineering should be strengthened rapidly in Australia to provide graduates for the industry.

Jan 1, 1969

Improving Pelletisation of Pyrite Cinder by High Pressure Roller Grinding As an important secondary resource for ironmaking, pyrite cinder is characterised by coarse particle size, low specific surface area, high porosity and poor surface activity, which leads to high bentonite dosage, low strength and too high moisture of green balls and high roasting temperature. In this paper, a study of improving the pelletisation of pyrite cinder containing feed by using high pressure roll grinding (HPRG) was presented, which aimed to improve the quality of green pellets and reinforce roasting performance pellets. It is shown that pyrite cinder is characterised by complicated mineral compositions dominated by haematite and metal sulfides, porous surface and middle class ballability, leading to higher balling moisture, higher bentonite dosage and higher firing temperature for pellet hardening. The pelletisation of pyrite cinder can be improved by high pressure roller grinding and blending with magnetite in the pellet feed. The former is probably ascribed to the increase in specific surface areas of pellet feed from 850 cm2+g to 1690 cm2+g when the pellet feed passes through roller twice. Good quality green balls and fired pellets can be made from feed comprising 40 - 60 per cent pyrite cinder and 60 - 40 per cent magnetite concentrate at small scale under the following conditions: 1.2 per cent bentonite, feed passing through roller twice at 7 per cent moisture at 1.5 ton pressure, balling at 13 per cent moisture for 13 min, preheating at 1050¦C for 12 min and firing at 1300¦C for 8 min. Green balls possess such properties as drop numbers of 6.5 times, compressive strength of 19.1 Newton and thermal shock temperature of 533¦C. Fired pellets are imparted high compressive strength of over 3000 Newton per pellet. Small scale tests have been proven by pilot scale tests that high grade fired pellets are made, assaying 63 per cent Fe and minor other impurities, such as sulfur and phosphorus except for copper content. The fired pellets made of three blends possess excellent metallurgical performance, such as reducibility index higher than 65 per cent, reduction swelling index lower than 15 per cent and low temperature reduction degradation lower than2 per cent. Especially the compressive strength after reduction is higher 719Newton per pellet.

Sep 13, 2010

By F. A. Guo

Ultrafine-grained surface layers were obtained by surface mechanical attrition treatment (SMAT) in copper and titanium samples. The thermal properties of the deformed layers were characterized using a scanning thermal microscopy (SThM) that allows thermal conductivity to be mapped down to the submicrometer scale. A theoretical approach, based on this investigation, was used to calculate the heat flow from the probe tip to the sample and then estimate the thermal conductivities at different scanning positions. Experimental results and theoretical calculation demonstrate that SThM can be used as a powerful tool for the thermal property and microstructural analysis of ultrafine-grained microstructures.

Jan 1, 2006

By Paul Semple

"In 2007, Noront Resources Inc. discovered the high grade nickel copper PGE deposit in northwestern Ontario in a region now known as the Ring of Fire. Since the initial discovery, Noront has advanced the Eagle¹s Nest Project and in September 2012 released a feasibility study for the development of the Eagle¹s Nest Project. This paper summarizes the results of this recent study and outlines additional work planned in the next stages of project development. INTRODUCTIONThe following paper summarizes the findings of the recently completed feasibility study on Noront Resources Ltd.’s Eagle’s Nest Project. The feasibility study was compiled into a NI 43-101 report by Micon International. This paper is intended to summarize the major technical findings and for complete information, interested parties can find the entire NI 43-101 report at www.norontresources.com or on SEDAR.LOCATIONThe McFaulds Lake project area, which includes the Eagle’s Nest deposit, is located at approximately UTM 5844000 N and 547000 E, and between approximately 52º42’ and 52º50’ N latitude and 86º06’ and 86º24’ W longitude, approximately 250 km west of the community of Attawapiskat on James Bay and 575 km northwest of Timmins. The closest all-season accessible community to the McFaulds Lake project area is Nakina, 300 km to the south, where there is a paved airstrip, in addition to all weather road and railroad access (see Figure 1).The First Nations communities of Webequie and Ogoki/Marten Falls are located 90 km west and 120 km south southeast of McFaulds Lake, respectively. Both communities are served by regularly scheduled air service, primarily from Thunder Bay; both Thunder Bay and Timmins serve as support centres for the James Bay communities and the exploration projects in the area."

Jan 1, 2013

By K. Woodward

"SynopsisSeismically active mines generally experience an increase in seismic hazard due to rock mass instability following blasting. Re-entry protocols commonly include measures to limit the spatial and temporal exposure of personnel to increased seismic hazard induced by blasting. The management of periods of increased seismic hazard requires the development of re-entry protocols for a unique mining environment. Identifying mining conditions that may result in significant seismicity following blasting relies on retrospective analysis, which is often focused on seismicity occurring within a certain period after blasting and within a certain radius of the blast in the broader context of site-specific experience.The analysis of seismicity without considering blasting times and locations allows for the relationship between seismicity and blasting to be investigated without prior assumptions concerning dependency. To achieve independent analysis, seismicity that is clustered in space and time (referred to as a seismic sequence) must be identified by assessment utilizing only seismic parameters. An automated algorithm is implemented that assesses the timing, location, and quantity of seismicity to identify seismic sequences, represented by the time of the first event and mean location of all events in the sequence.The relationship between sequences and blasts is assessed by calculating the distance and time from each sequence to the closest blast in space and time. Establishing an independent classification between sequences and blasting provides insight into the unique cases where seismic sequences are remote and/or delayed with respect to blasts and identifies cases when sequences exhibit a weak relation to blasting. The nature of seismic responses to blasting has direct implications for the management of the increased seismic hazard associated with seismic sequences.The approach presented in this study contributes to the management of seismic hazard by providing empirical support for the relationship between seismic sequences and blasting. These relationships indicate the portions of sequences that can and cannot be practically managed using tactical approaches. Furthermore, the analysis of sequences reveals the nature and evolution of rock mass responses to blasting. These results have implications for the extent of spatial or temporal re-entry restrictions required for the optimal management of time-dependent rock mass response to mining."

Jan 1, 2015

By R L. Brathwaite

The epithermal gold-silver deposits wall poster is one in a series of posters on different mineral deposit types being produced by GNS Science to raise awareness of the characteristics of New Zealand mineral deposits and their prospectivity. Epithermal deposits consist of quartz veins, quartz vein stockworks and hydrothermal breccias that are mainly hosted in subaerial andesitic or rhyolitic rocks of Tertiary age. The deposits were formed at depths of typically less than 1 km and at temperatures between 180¦ and 320¦C, although ore grade mineralisation was generally deposited at less than 270¦C.   In New Zealand, epithermal deposits occur in association with late Cenozoic volcanic rocks in the Northland, Coromandel and Taupo volcanic regions. All of the past and present gold production, estimated at greater than 380 t (along with 1300 t Ag) comes from the Miocene-Pliocene Coromandel Volcanic Zone, where about 50 epithermal gold-silver deposits occur over a 200 km long belt. In Northland, silver and mercury have been produced from hot spring type epithermal deposits, and several gold-silver prospects have been identified. Ore grade gold-silver mineralisation is currently being deposited in several active geothermal fields of the Taupo Volcanic Zone, and extinct geothermal systems occur on the western side of the zone. The active systems have provided natural laboratories to help understand the processes of epithermal mineralisation.

Jan 1, 2005

By L. J. Kane

Conventional methods for determining the size of dust suspended in a gas require that agglomerates (clusters of particles) first be broken into particles, but in evaluating industrial dust-removing equipment the size of the agglomerates as they actually exist in the gas stream is far more important. This paper presents results of an investigation by the Federal Bureau of Mines to develop methods for determining the size of dust agglomerates suspended in a gas stream. The studies are part of the Bureau's continuing research on synthetic liquid fuels. The size and size-distribution of agglomerates as they exist when the gas reaches the filter was determined by using a membrane filter in conjunction with a dust count under a microscope. A membrane filter is a cellulosic sheet about 150 microns thick containing millions of holes per square centimeter--holes of uniform diameter that run directly through the sheet without interconnection.

Jan 1, 1960