Search Documents

By James R. Wait

An attempt is made here to collect together various reports and publications that are based on research supported all or in part by Contract No. H0155008 for the past two years. The subject matter deals primarily with the excitation, transmission, and reception of electromagnetic waves in mine environments. This contract from the U.S. Bureau of Mines with the Office of Telecommunications supports the efforts of James R. Wait (Principal Investigator and Consultant to OT), David A. Hill (Co-Investigator), and various associates within the Boulder scientific community. The contributions of Samir F. Mahmoud were supported, in part, by the contract while he was a Visiting Fellow with the Cooperative Institute for Research in Environmental Sciences at the University of Colorado. Administrative assistance in CIRES has been provided by Mrs. Lana R. Hope.

Jan 1, 1976

By Frederic Dewey

(New York Meeting, February, 1913) This old and well-known method of determining, silver is, in bullion work, so far superior to the furnace-assay that it is looked upon with reverential awe by many, if not by most, users, and its-ease of execution, with proper equipment, commends it highly where much commercial bullion work on silver is required. The method is so thoroughly well known that a, description of it here may seem to be unnecessary, but many thousands of determinations are annually made by it in the U. S. Mint Service and its practice is there reduced to an art. This is necessary both for the sake of economy of time, acid because high-grade work with it requires constant practice. It is useless for a person who uses it only occasionally to expect to attain high accuracy with it, without spending more time upon a determination than is warranted in a busy commercial laboratory. It is always employed in the Mint service whenever possible, but its chief field is in the determination of silver in standard silver (ingots and coin), which is 900 fine in silver and 100 fine in copper, and I shall first briefly outline its use on this metal and then take up various points in detail, especially as related to the accuracy of the results obtained.

Jan 4, 1913

By Zhang Libo, Peng Jinhui, Zhang Zhengfu, Fu Mengbi, Han Yamei

In this paper, results of a novel synthesis method of carbon-coated LiNi113Mn113Co11302 cathode material for lithium-ion battery are reported. The carbon coating was produced from a precursor, glucose, by microwave-pyrolysis method. The structure, morphology and electrochemical performance of the bare and carbon-coated LiNi113Mn113Co11302 were characterized by X-ray diffraction, scanning electron microscopy and charge-discharge tests respectively. The L8(27) orthogonal experiments were carried out to optimize LiNi113Co113Mn1130z/C technological conditions. The conditions of the orthogonal experiments were that the glucose content were 1.5 % and 4 %, the holding time were 15min and 30min, the heating temperature were 400 °C and 500 °C and the solvent were H20 and CH3CH20H. The main experiment target include specific capacity at 0.1C and 0.2C, Capacity retention rate, medium voltage attenuation rate and The fifth discharge medium voltage. The data were analyzed by Minitab 14 statistics software. The results of analysis of variance indicated that the most influential factor was the glucose content despite of discharge rate. Secondly, the effect of the solvent was equivalent to the holding time.

Jan 1, 2013

By PAUL M. Tyier

NOW that analytical chemistry has gone so far to debunk early misconceptions about minerals, the fact that the light of exact knowledge still fails to illuminate many dark corners is often overlooked. By combining the skills of the physicist with those of a chemist, the identification of minerals has become an exact science and the presence of even minute traces of impurities and extraneous elements is readily revealed by spectrographic means, Granted that we can learn all there is to know about the composition of a substance and even about its physical propertied (which latter assumption is somewhat far-reaching) it still does not follow that we clearly understood its commercial designation or utility.

Jan 1, 1941

By G. H. Keith

Oxygen and nitrogen cause strain aging in electrorefined vanadium, as evidenced by maxima in yield and tensile strengths and by Snoek internal friction peaks. Alloys containing up to 0.22 percent oxygen and 0.11 percent nitrogen were investigated. Tensile strengths of oxygen-and nitrogen-containing alloys were 66,000 and 68,000 psi at 300° to 400° C, compared with 53,000 and 62,000 psi, respectively, at room temperature. Total elongation decreases to about 7 percent at the temperature of maximum strength. At 600° C, strain aging is not evident. Based on interstitial contents calculated from internal friction measurement, the increases in strength caused by nitrogen and oxygen were 440,000 psi per weight-percent nitrogen and 260,000 psi per weight-percent oxygen. Application of the Schoeck and Seeger treatment to the Snoek effect in these systems results in a calculated lattice distortion of 0.24 and 0.15 caused by the presence of an interstitial nitrogen or oxygen atom, respectively. Alloys containing boron or carbon were also investigated. Both elements refine the grain size but have no other effect because of their low solubility in vanadium.

Jan 1, 1969

By K. Delbeke

Within the framework of the EU Existing Substance (93/793/EEC) and REACH regulations EC/1907/2006), the copper industry initiated in 2000 a comprehensive Voluntary Risk Assessment of copper and several copper compounds. The Italian Government's Istituto Superiore di Sanità, reviewed the process and reports on behalf of the European Commission. Copper exposure levels to man and the environment from production of copper anodes and cathodes, copper powders and copper chemicals as well as fabrication and use of semi-fabrication products and down stream user products were collected across Europe. Environmental and human health effects data were obtained from literature as well as novel research programs and used to deduct safe threshold

Jan 1, 2007

The request for proposal from the U.S. Bureau of Mines outlined the purpose of this study in the following terms. "High grade near surface deposits are largely a matter of history. Most of the current mineral production in the united States is from large low grade ore deposits mined by large scale methods. It appears likely that exhaustion of near surface deposits and public resistance to open pit mining will tend to reverse the present trend toward open pit mining and lead to increased reliance on large scale underground mining. In view of the long lead time needed to improve basic technology, an in-depth study of the major underground mining methods is needed. "This study is intended to provide a systematic review and analysis of large scale non-coal underground mining technology with particular emphasis on current practices and problems, needed technological improvements, existing or potential environmental conflicts, and possible modifications or innovations that will assist in the satisfaction of projected national mineral supply requirements."

Jan 1, 1974

By S. Grogan

Next year marks the tenth anniversary of the Surface Mining Control and Reclamation Act (SMCRA). As the U.S. coal industry scrambles to cope with serious economic difficulties, it is appropriate to examine some other difficulties that have their origin in certain provisions of that ten year old law, and that bear directly on the economic viability of surface coal mining in the west. This paper focuses briefly on three technical issues in the reclamation of surface coal mines in arid regions, and suggests that innovation can resolve these issues. The coal industry operates within a narrow legal context, defined in 1977. In enacting SMCRA, Congress listed among the purposes of the Act ?... to...strike a balance between protection of the environment, agricultural productivity and the Nation's need for coal as an essential source of energy." I maintain that such a balance has never been struck, particularly with regard to the reclamation of mines in the west. One reason is that when SMCRA was enacted its supporters were aware of uncertainties about the potential for successful reclamation of western surface mines. Over the intervening years, as a recent Congressional study report (OTA, 1986) points out, "...the risks these uncertainties may pose to the long term success of western reclamation have been reduced significantly." Unfortunately, SMCRA's enforcement agency, the Office of Surface Mining (OSM) has not yet recognized this fact, and the western coal industry is paying the price.

Jan 1, 1986

By Walter Nuñez

La finalización de la estimación de reservas de un modelo de mina cuestiona la asertividad del modelo de Mina para la planeación minera. En ese sentido, el presente texto señala la Reconciliación como la comparación real histórica de tonelaje, leyes y contenido fino estimado, entre el modelo de mina y planta concentradora. La reconciliación permite conocer y ajustar mediante el uso de factores, la planeación mensual y anual de los siguientes años de la operación minera, y así cumplir con los compromisos mensuales asumidos de envío de contenido fino desde mina. Así también se muestra el proceso que sigue la explotación minera a tajo abierto en Toquepala, las variables que influyen en la variación de la reconciliación y algunas pautas a considerar para minimizar estos errores de reconciliación entre mina y concentradora.

Sep 19, 2006

By Orlando Martino

This regional report covers the mineral industries of Canada and 40 countries and areas in Latin America and the Caribbean Basin. Also included is a brief description of the mineral potential of Antarctica. The Latin American region encompasses an area twice that of the United States. Latin America and Canada have a rich and diversified endowment of mineral fuels, metals, and industrial minerals. Tables 1 and 2 provide a summary view of Latin America and Canada's output of its major mineral commodities in world mineral supply in 1990 and 1991. Table 3 shows the relative importance of a selected group of minerals produced in Latin America in the world mineral economy.

Jan 1, 1993

By W. Kunda

Silver nitrate solution is a very common product in hydrometallurgical processes involving the treatment of various silver bearing materials. Silver is recovered by electrolysis. The alternative method for the recovery of silver from aqueous solutions is the precipitation by hydrogen at elevated temperature and pressure. A previous study by the authors revealed the feasibility of this technique for the silver ammine sulfate system. Further study showed different behavior for silver in the silver ammine nitrate system and a systematic study was initiated to establish the optimum conditions for the process. The study showed that the process can be controlled by (1) composition of the feed solution, (2) temperature and (3) hydrogen pressure. The recovered silver product was in the form of very fine powder.

Jan 1, 1989

By I. M. Wolf, S. A. Usmar, L. A. Cornish

The limiting criterion in the use of stainless steel for certain forming operations such as coining is its hardness, which determines parameters such as required striking pressure, wear on dies, and integrity of pattern detail. Attention is given here to the development of ultra-soft ferritic stainless steels for coinage. In the first instance, the influence of carbon content on the striking properties of a series of commercial and experimental 17%Cr alloys was evaluated. It was found that a lower carbon content permitted the striking of relatively highly profiled and intricate patterns, provided that the hardness did not exceed 125 HV. Hardnesses as low as 115 HV were achieved in the fully annealed condition, but these alloys required high striking pressures. In a further study, three grades of experimental 14%Cr ferritic stainless steels were produced with a view to optimizing the ductility. When the residual impurities were minimized, hardness values of about 100 HV and lower were achieved. Micro-alloying additions allowed the heat-treatment response and grain size to be controlled. Excellent tensile properties, with elongations of up to 42 per cent, were achieved in the fuly annealed condition, and highly profiled patterns were produced in coining trials.

Jan 1, 1993

By Joel N. Van Sant

An investigation was conducted to study possible sources of Utah refractory and structural clays that could be used for the manufacture of refractories and light or buff burning heavy-clay products. A field study was made and the clay samples tested to determine their firing characteristics. Results of the Bureau's work indicate many small noncommercial deposits of hypogenic clay occur in igneous rocks. Commercial hypogenic deposits are mostly halloysite clay developed by hydrothermal replacement of limestone. The high firing shrinkage of halloysite precludes its use as a refractory, however, halloysite produced at the Dragon Mine south of Eureka, is used fur making oil catalysts. Clays and shales suitable for low heat duty refractory products are found in the Manning Canyon shale, in shales associated with coal bearing rocks, and in the Dakota formation. Some of the clays from the Dakota formation are also suitable for high-duty refractory products.

Jan 1, 1964

By Primak. George J.

"In the development of a new product as well as during its introduction on the market, it is very important to give due consideration to problems involving patents, licenses and trade marks. At the very beginning of the research and development program, it is obviously essential to ascertain, through a suitable patent search, that the product in question will not infringe any patents which are still in force. Then, a possibility of achieving one's own patent or proprietary position on the product or the process of its manufacture should be carefully explored. Licensing arrangements that one may reach with respect to patents and know-how covering such new product may, in the final analysis, determine its over-all success or failure. If one can count on licensing revenues or some favourable cross-licensing arrangements with respect to a newly developed product, this may go a long way to achieving profitability and success. The selection of a good trade mark is probably one of the most important acts that one has to perform once the product is developed, as customers will identify the new product by such a trade mark. In many instances, successful marketing and widespread acceptance of a product are largely due to its appealing name or trade mark, accompanied by proper promotion and advertising. Once the trade mark has been adopted, it should be registered in the Trade Marks Office to provide the protection afforded by federal statute. If the product is to be manufactured, sold or licensed in some other countries, similar considerations should be made with regard to each such country."

Jan 1, 1973

By Kah Lert

"The Red Mountain porphyry molybdenum deposit is situated in the Big Salmon Range, approximately 80 km east-northeast of Whitehorse, Yukon.Red Mountain is underlain by Paleozoic, argillaceous sedimentary rocks of the Yukon Cataclastic Complex, which have been intruded by a multi-phase mid-Cretaceous stock.Mineraliwtion, quartz stockwork, metal zonation, and an alteration assemblage characteristic of a porphyry molybdenum system have been superimposed on quartz monzonite porphyry and adjacent homfelsed sedimentary rocks. A later, barren and pyritic quartzeye diorite porphyry body and related dikes have dissected the quartz monzonite porphyry, homfelsed sedimentary rocks and associated molybdenite mineralization.Drill-indicated geological reserves of molybdenum mineralization outlined consist of 187 270 000 tonnes grading 0.167% MoS2.IntroductionLocationThe Red Mountain porphyry molybdenum deposit is located at 60°59'N, 133°44'W (NTS 105 C), approximately 80 km east-northeast of Whitehorse, Yukon. The property is situated within the rugged Big Salmon Range, 15 km east of the north-northwest-trending Teslin River. Red Mountain, at an elevation of 1702 m, consists of relatively steep, talus covered slopes with prominent gossanous bluffs marking the southeast flank. Relief on the property is 700 m, with tree-line at an elevation of 1450 m to 1500 m (Fig. 1)."

Jan 1, 1995

Prof. A. Ledebur, Freiberg, Saxony :* Mr. Sauveur has presented and enriched with original observations a valuable summary of the theories advanced hitherto concerning the hardening of steel; but in one particular, it seems to me, his statements call for correction. He says:

Jan 1, 1898

By Jay F. Colinet

Coal workers’ pneumoconiosis (CWP), commonly known as black lung, is caused by the inhalation of respirable coal mine dust and is a disabling and potentially fatal lung disease with no cure. Historically, CWP has taken a tremendous human and financial toll in the US coal mining industry. Recent health surveillance data indicates that CWP continues to occur at elevated levels. Respirable coal dust exposure must be controlled to prevent the development of CWP. The Pittsburgh Mining Research Division of the National Institute for Occupational Safety and Health (NIOSH) conducts laboratory and mine-site research to identify control technologies that can be used to successfully reduce respirable dust levels. Various technologies, using multiple methods of control, can be applied in order to reduce dust levels. An overview ofCWP’s impact and a general methodology for controlling respirable dust in underground coal mines are discussed in this paper.

Jul 30, 2020

By D. Harrington

This circular presents Part III-A of a series reviewing the literature on effects of breathing dusts with special reference to silicosis; it deals with the economic and legal aspects of dust diseases in industry; Part III-B will contain data on the status and cost of compensation for silicosis, Parts I and II of the series have been issued as Information Circulars 6835, 6840, and 6848; Part I defines and classifies dusts, indicates sources of exposure, and describes the physiological effects of breaching dusts; Part II-A discusses the principal dust factors producing pulmonary pathology and methods of determination of dust in air; and Part II-B presents data on the engineering and medical control in the prevention of dust diseases and general recommendations for their control in industry. A summary and general conclusions will complete the series.

Jan 1, 1935

By J. A. Jr. Carpenter

Expanding world economic prosperity, probable peaking of conventional petroleum production in the coming decades and environmental concerns require efforts to increase the efficiency of, and the development of alternatives to, petroleum-based fuels used in automotive transportation. In January 2002, the U.S. Department of Energy (USDOE) and the U.S. Council for Automotive Research (USCAR) of the "Big Three" traditionally-USA-based automakers, DaimlerChrysler, Ford and General Motors, formed the Freedom Cooperative Automotive Research (FreedomCAR) Partnership to fund high-risk, high-payoff research into advanced automotive technologies with the potential for eventually lowering the USA's nearly complete (95%) dependence on petroleum, 55% imported, for its transportation fuels. FreedomCAR replaced the Partnership for a New Generation of Vehicles (PNGV) which existed from 1993 to 2001. In January 2003, the energy-supply industry joined with the FreedomCAR Partnership forming the FreedomCAR and Fuel Initiative (FC&FI) to develop the technologies needed for the mass production of fuel-cell vehicles using hydrogen as fuel and the infrastructure needed to deliver the hydrogen to the consumer. The goal is to enable the automotive and energy-supply industries to make commercialization decisions in 2015 on large-scale introduction of such vehicles and on developing the infrastructure beginning in 2020. In addition to work on fuel cells and hydrogen infrastructure, the FC&FI conducts research on technologies with the potential for nearer-term energy efficiency and environmental benefits, such as new engine concepts, lightweight materials, and engine-electric hybrid propulsion systems. Lightweighting is seen as crucial for shorter and for longer term benefits because hybrid and fuel-cell powertrains are expected, at least in the early stages of adoption, to be heavier and more costly per unit of power than the standard internal-combustion, gasoline- or diesel-fueled powertrains they replace. Research and development (R&D) on casting of aluminum automotive components were major parts of the PNGV and R&D on casting of magnesium automotive components have been and are so under FreedomCAR. This presentation will review those efforts.

Jan 1, 2006

By W. W. Agey

As a part of the program of investigation of domestic sources of manganese in the western United States, engineers of the Bureau of Mines examined. and obtained samples of ore from two properties in the vicinity of Barstow, San Bernardino County, Calif. In addition to these, samples from two other properties in the same vicinity were submitted by the owners. As the ores were too low-grade to be acceptable for the direct production of ferromanganese, beneficiation studies were made to determine the amenability of the ores to concentration by ore dressing. The Big Reef manganese claims axe about 140 miles east of Barstow, Calif. The claims were leased by W., E. Thurber of San Gabriel, Calif., from the owner, C. S. VanDoren of Daggett., Calif. Manganese oxides occur as a replacement deposit in heavily brecciated andesite along a fault plane. Four samples were taken by an examining engineer of the Bureau of Mines from the ore zone, which, when composited, were representative of all the exposed ore. Preliminary tests were made on lot B, and final tests wore made on the composite sample. The Trans-Oceanic property is about 20 miles southeast of Barstow, near Newberry, in the. Pisgah mining district, Calif. The sample, submitted by the owners, was taken from a 1,000-ton reject clump from a hand-sorting operation. The ore occurs as a replacement of rhyolite.

Jan 1, 1952