Search Documents

By Shamim A. Dar, Mohd Shuaib, K. F. Khan, Samsuddin Khan

The Late Paleocene–Middle Eocene phosphate nodules of Solan District of Himachal Pradesh belong to green facies of Subathu Formation of Sirmur group. Field observations indicate sporadic distribution of phosphatic nodules in the yellow brown to rusty brown, buff-colored bleach shales. Phosphatic nodules are dull earthy to dark grayish in color and break with sharp and conchoidal surfaces. Studies of phosphatic nodules using petrological microscope, X-ray diffractometry, and scanning electron microscopy (SEM) attached with energy dispersive X-ray (EDX) reveal that cryptocrystalline apatite (fluorapatite) is the dominant phosphate mineral. Silt sized silica is the dominant gangue, whereas pyrite and muscovite are present as minor gangue. The phosphate minerals occur as oolites, pellets, and cryptocrystalline apatite in the groundmass. Silica veins form a network replacing the original phosphatic matrix. Brown to brownish black color may be attributed by the organic matter in the phosphatic nodules. Completely phosphatized radiolaria and partially pyritized planktonic foraminifera are observed. There is corroboration of organic matter in the form of microbial filaments in the groundmass of apatite. The findings in the present investigation indicate that the different forms of the minerals, their texture, and distribution in the phosphatic nodules might be due to environmental vicissitudes in oxidizing to reducing conditions followed by replacement processes. Presence of microbial filaments may be due to the active role of microorganisms during the formation of these phosphatic nodules.

The limit of pressure to which an underground dam may with safety be subjected, is a question that-as far as the writer knows has not received the same attention from authorities on engineering construction, or practical mining, that has been accorded to questions on which the design and strength of other structures or machines in connection with a mine are based. That dams may, under certain conditions, be constructed to resist water under great pressure is a known fact. But the difficulty of demonstrating beforehand that any proposed structure of this kind will withstand the pressure and be effective is, owing to the indeterminate nature of some of the risks to be provided against, very great. In the present state of our knowledge it may almost be laid down as a rule, that a dam of this kind should not be undertaken where grave consequences would attend failure until experience of structures where the physical conditions are similar, but where there are no such risks, has given assurance that such work would stand.In Mines and Minerals for May, 1900, there is published a paper by Mr. James McNaughton describing the construction of three underground dams in the iron mining district of Michigan.The first of these was put in to hold back a flow of 750 gallons per minute, which when pent up created a pressure of 276 pounds per square inch, showing that the height of the sustained column was about 635 ·feet. The hole through which the water issued was in the bottom of the cross cut it was enlarged by removing all loose rock for a depth of 18 ft...

Jan 1, 1901

By M. A. Reyes, L. Yan

Heat and humidity buildup within refuge alternatives (RAs) may expose occupants to physiological hazards such as heat stress. The Mine Safety and Health Administration (MSHA) regulations require RAs in underground coal mines to provide a life-sustaining environment for miners trapped underground when escape is impossible. RAs are required to sustain life for 96 h while maintaining an apparent temperature (AT) below 95 °F (35 °C). The National Institute for Occupational Safety and Health (NIOSH) tested a 10-person tent-type RA, a 23-person tent-type RA, and a 6-person metal-type RA in its underground coal mine facilities to investigate the thermal environment over a 96-h period. The test results showed that mine air and mine strata temperatures surrounding an RA occupied by simulated miners (SMs) increased over the 96-h test period. The test results suggest that RA manufacturers should consider this increase in temperatures when calculating and evaluating RA components during surface and laboratory tests. The findings can equip stakeholders with additional considerations for calculating the interior heat and humidity temperature profiles for occupied RAs not tested in situ

Nov 22, 2019

By Micah Nehring, MEHMET KIZIL, Farzad Sotoudeh, Amin Mousavi, PETER KNIGHTS

Production scheduling in underground mines is one of the most important and complex processes in maximising the economic value of an operation over the life of the mine. Due to increasing energy, transportation, processing and smelting costs and reducing water availability, the extraction of ore deposits through underground operations has become more expensive and challenging. A potential productive and efficient solution to mitigate these issues is to integrate pre-concentration systems into the existing mining system to increase ore grades through a preliminary process of rejecting some waste before sending the ore to the energy intensive mineral processing plant. Further benefit of such systems includes the utilisation of the waste and low-grade material in backfilling of open stopes to reduce the transportation costs and surface environmental impact such as reduction of CO2 emissions and waste transportation. The objective of this paper is to present a new mathematical model to optimise the production schedule of underground metalliferous mining operations in the presence of a pre-concentration system. The proposed model optimises the production schedule and sequencing of stopes within a sublevel stoping operation. The results of this study illustrate the potential economic benefits of using a pre-concentration system prior to a mineral processing operation as a result of increased net present value.

Nov 16, 2023

By R. Simkus, J. K. Gowans

Polaris Operations, a Cominco Ltd. lead-zinc mine, is located on Little Cornwallis Island, Northwest Territories, at Latitude 75°23' N and Longitude 96°75' w. When the Polaris Mine went into operation in late 1981, it became the world's most northerly base metal mine.The Polaris Concentrator, housed in a unique process barge, is a basic lead-zinc concentrator where flotation is used to produce the lead and zinc concentrates.The paper describes the ""coarse lead"" flotation feature incorporated in the concentrator flowsheet and describes the start-up problems and continuing operation of this circuit.

Jan 1, 1984

By H. Reginald Hardy

This report is Volume II of a three volume final report dealing with the microseismic monitoring of a longwall coal mine. The research presented in Volume II is concerned with the evaluation of field techniques for obtaining seismic velocity data required for computing microseismic source locations. The report describes the evaluation of a number of different field techniques and the seismic velocity data obtained at the Greenwich mine site where the micro-seismic studies, described in Volume I of the final report, were carried out. Three different methods were employed to evaluate seismic velocities, namely; surface refraction, down-hole, and transmission. In all cases the seismic sources were either located on surface (mechanical impact) or near-surface (explosive charges). It was found that a mechanical energy source could be conveniently utilized to determine shallow velocities and make bedrock-regolith interface depth determinations. For deeper velocity determinations suitable explosive charge sources Here required. In general, refraction data did not always plot in a linear manner and some subjective interpretation was necessary. The down-hole method was found to be useful for incremental vertical velocity evaluation, however, the transmission method provided the most consistent average vertical velocity data. At the Greenwich site seismic velocities were found to be anisotropic with values ranging from 9,551 to 10,739 feet per second depending on direction.

Jan 1, 1977

By G. K. Jorgenson, S. H. Chung

"IntroductionThe SABREX Blast Modelling Program was developed jointly by the companies of the ICI Explosives Group, of which C-I-L Inc. is a member. SABREX (Scientific Approach to Breaking Rock with Explosives) is a modular computer program which incorporates new technology with a number of tested programs that have been in use world wide.SABREX predicts the performance of blasts in terms of (I) fragment size and distribution; (2) muckpile profile and face velocity; (3) grade fracture; (4) collar breakage; (5) a rupture envelope which depicts crack penetration behind and beneath blastholes; and (6) a complete cost analysis including explosives, drilling and accessory costs. The predicted blast results are displayed as dynamic colour graphics and in tabular form.SABREX uses data on the detailed geometry of the drilled and loaded pattern, detonation characteristics of the explosives and the dynamic properties of the rock to generate blast predictions. SABREX blasting calculations take into account the effects that shock and quasi-static pressures exert on the rock around the blastholes. While physical effects occur very rapidly in rock blasting, it is possible to view and model the sequence of events as discrete sections.The program can be run on a microcomputer and is currently operated by C-I-L technical service staff in Canada for the use of drilling and blasting operators.Figure I is a diagram representing the modules of the program and associated technology that is used to complement the program.Any, or all, of the modules may be used in a particular study or blast optimization. Because the BOBCAT module of the SABREX program has been described in previous papers(7.8.9), this discussion will concentrate on the newer modules: CRACK, HEAVE, RUPTURE ENVELOPE and to a limited extent, KUZ-RAM, which present a more detailed picture of the blasting process.Each of these modules is discussed in terms of the information they offer the operator in analyzing the blast. Specific examples of recent usage in Canadian mining situations are included to illustrate the ability of the model to produce practical results that can assist in optimizing actual blasting operations or solving problems that do exist."

Jan 1, 1987

By C T. Hollick

Conventional processing of heavy mineral deposits containing radioactive rare earth minerals such as monazite and xenotime may cause industrial hygiene problems through atmospheric dust and contamination of product concentrates. An alternative procedure has been developed in which such minerals are removed from bulk heavy mineral concentrates by flotation with little loss of other economic minerals. With fine ores, recoveries of over 95 per cent have been achieved and with coarse ores over 80 per cent, in both cases at high grade. Several flotation regimes have proven effective. The potential for generation of radioactive dust or product contamination is subsequent processing is correspondingly reduced.

Jan 1, 1990

By R. T. Jones

DC arc furnaces are widely used for steel scrap melting as well as for reductive smelting of ore fines. Industrial smelting applications include the smelting of chromite to produce ferrochromium, the smelting of ilmenite to produce titania slag and pig iron, and the recovery of cobalt from nonferrous smelter slags. A number of myths and misconceptions are widely held, especially regarding: the age of the technology, the use of a hollow electrode, arc stability and shape, arc and bath radiation, interaction between the arc and molten slag, electrical behaviour of arcs and slags, a comparison between AC and DC furnaces, DC reactors, the lifespan of bottom electrodes, and the applicability of DC arc furnaces to various metallurgical systems.

Jan 1, 2011

It cannot be said that accurate and reliable ore reserve estimation is the fundamental of any mining operation success. Estimation techniques which are used to estimate the grade distribution of an orebody together with the assessment of uncertainty and risk have a vital influence on the success of any optimisation algorithm. Traditional estimation techniques such as kriging or inverse distance weighting are frequently used for assigning grade values to blocks. Various attempts have been made in order to compare geostatistical estimated methods for ore reserve estimation. This paper aims to evaluate the sensitivity of different estimation methods over changing the block dimension. For this reason, several block models with different dimensions were derived in Chador Malu iron ore mine which is located in 180 km northeast of Yazd in the centre of Iran. Each block model was estimated by different estimation methods such as nearest neighbours (NN), inverse distance (ID) and ordinary kriging (OK). The results of each estimation methods were compared against a control block file created by using the assay results of all blastholes drilled in the ore over four benches of the pit. The results signify that by estimating the large block size, no significant improvement occurred due to the employment of different estimation techniques. Furthermore, the grades estimated based on ID method is more reliable, but OK methods estimated more accurate tonnage.

Dec 6, 2010

By Goldney L. H

The authors review the literature and discuss the application of methods to the design of thickeners for ilocculated metallurgical pulps. The use and evaluation of flocculents is described. Experimental data show that design based upon laboratory settlingdata is acceptable. The economic aspect of design is also discussed.INTRODUCTIONFor many years there has been little change in the methods for the design of thickener installations. While modifications have been made in the method of applying the data all methods have been based on the observee settling rate of the solids. The development of a theoretical approach based on physical data would involve so many variables which affect the settling rate that the more practical approach of direct observation seems unlikely to be replaced as the basis of design.The advent of synthetic fiocculents has introduced a modification in operation which affects design and should be considered. The authors review the subject and attempt to bring it up to date with present day procedure. Until recently the original work of Coe and Clevenger (1916) remained the basis of thickener design. They described their observation of the different zones encountered in settling, namely clarification, feed, transition, and compression or thickening- zones. The solids pass through the transition zone in settling from feed density to some higher density where settling ceases and ·some compression or compaction effect controls. the density obtained. The point at which the settling zone ceases to exist is known as the critical point.

Jan 1, 1959

By Kazunori Matsushita, Masaru Sakakibara, Kenji Harada, Naotoshi Shinkawa, Mitsuo Nozu

The Sand Compaction Pile (SCP) method has been widely used as a typical countermeasure against liquefaction in Japan, and its effectiveness has been confirmed in many case histories of damages caused by the past large-scale earthquakes. A series of studies were conducted to evaluate the effectiveness of the compaction method and other factors, if any, in sustaining a seismic force that is greater than the assumed one and caused no damage. Based on the results of these studies, the Architectural Institute of Japan (AIJ) has indicated in its “Recommendations for Design of Ground Improvement for Building Foundations” published in 2006 that the liquefaction resistance ratio (tl/sz) of the composite ground, which consists of sand piles and surrounding compacted ground, is higher than the RL calculated by using the SPT N-values of the ground in-between the sand piles. In this paper, statistical analysis of safety factor against liquefaction, FL, was performed by using the SPT N-values of ground in Port Island and Rokko Island which were both fully reclaimed islands in Kobe city during the 1995 Hyogo-ken Nambu Earthquake (classified as intense shaking) and, together with the consideration of relative settlement, resulted in tl/sz of the composite ground being 1.5~2.5 times of tl/sz of the soil in-between piles after improvement. Furthermore, the liquefaction resistance curve of SCP-improved sites obtained from the relationship between SPT N-values and cyclic shear stress ratio during the 2011 off the Pacific Coast of Tohoku Earthquake, which was regarded as long-duration earthquake, was plotted to the left side of the curve originally proposed by Japan Road Association. Thus, the liquefaction resistance of the improved ground was found to be higher than that of the natural ground, even for the same SPT N-values, verifying the validity of the AIJ recommendation.

Jan 1, 2017

The Sandvik DE710 diamond core drill has become one of the most popular exploration drills available. It is operated on exploration and mining projects in locations around the world. The compact nature of the DE710 allows a small footprint on site. This has proven to be a great benefit in difficult access areas where site preparation can be limited. The DE710 drill is available in a range of con-figurations to suit global operational and environ-mental demands. It can be truck-mounted for greater maneuverability and ease of relocating the drill between sites. The drill can also be fitted to crawler tracks, powered from the rig hydraulic system, making it a small, self-propelled unit for areas with difficult site access. And the DE710 is available in a shack-mounted configuration for cold weather applications, ensuring a protected working environment for the drill crew. The DE710 is powered by a 6.7-liter engine that produces 141 kW (190 hp) at 2,200 rpm to power the rig hydraulic system. The engine complies with the Tier 3 emissions standards that are being introduced in many countries. The hydraulic system design for the Sandvik DE710 is based on the company?s philosophy of selecting the best available products to suit the application. The main hydraulic pumps and motors are the variable displacement design. This allows for greater fl exibility and precise control of critical drilling functions. The cooling system has also been designed for operation in ambient temperatures up to 50° C (122° F) to cope with varying global operational demands.

Jan 1, 2009

By Browner R, Lincoln F. J

The activity of silver in solid gold-silver alloys (electrum) has been measured with an electrochemical concentration cell based on the super ionic conductor silver-i3-alumina in the temperature range 200 to 80oaC.The measurements of the silver activity in the range 0.5 to 90.0 atom per eent silver were found to be highly reproducible although there is some disagreement with an earlier study which used a similar technique. At temperatures above 400° the silver activity exhibits both positive and negative deviations from ideality in the silver rich region.This method suggests a simple technique for the nondestructive determination of silver in electrum alloys.

Jan 1, 1983

The structure of the Bulli coal seam at Appin Colliery was detailed by the seismic reflection method. This unusual application of the seismic method was possible because there is a reflector near the seam as was revealed during exploration for petroleum in an area north-west of Appin. The reflector, which was at a depth of 1,500 ft, was shallow by normal reflection survey standards. Measurement of the seismic velocity at two ventilation shafts showed that the reflector was probably the Bulli coal seam. Accurate depth control was established from previous drilling results.INTRODUCTIONAppin Colliery, situated on the Southern Coalfield of N.S.W. (Fig. 1), is being developed to supply coking coal to the Port Kembla steelworks of Australian Iron and Steel Pty. Ltd. The colliery is mechanized and a detailed knowledge of structure, particularly faulting, is important in planning the workings.The Bulli seam, which is approximately 9 ft thick, and between 1,500 ft and 1,800 ft below the surface, is worked in the colliery. It is the uppermost member of the Permian Coal Measures and is overlain by Triassic rocks, which consist of thick sandstone beds containing beds of coloured shales, and which are subdivided into the Narrabeen Group, the Hawkesbury Sandstone, and the Wianamatta Group.In the early stages of development of the colliery, surface geological mapping and diamond drilling provided information on structure. Generalized results of the mapping are shown on Fig. 2. Drilling indicated that the physical and chemical properties of the Bulli seam are relatively constant, and that the seam is nearly horizontal, the average dipbeing about 1 in 25 to the west.

Jan 1, 1965

By A Tinnelly

Land disturbed by alluvial gold mining should be restored to a capability or productivity as good as that which existed prior to disturbance.   Effective rehabilitation requires detailed planning prior to mining and must also be closely integrated with the mining operations.   The main constituents of a rehabilitation plan: description of existing site conditions, choice of final land use, establishment of final landform, water management and erosion control, soil reconstruction, revegetation and management of rehabilitated land are briefly described.

Jan 1, 1989

By T. Khumalo, L. P. Coetzer

This paper addresses the impact of the variable speed drive on the particle size distribution in the product of a fully autogenous UG2 grinding circuit. It further discusses the impact of a varying particle size distribution in the product of the mill on the downstream classification and milling circuits. An industrial case study was used and data is presented to illustrate the techniques applied to identify the root cause of the shift in operational efficiency. The results achieved from both the investigation into the shift in plant efficiency and the sub-sequent corrective action taken illustrate that the root-cause methodology used in advance control can be effectively applied on production sites to both detect the shift and identify probable root-causes. The industrial example used confirms that the variable speed drive in a UG2 autogenous milling operation is a critical control parameter to ensure that the plant operates to design specifications.

Jan 1, 2006

By Thomas P. Mucho, Thomas M. Barczak, Dennis R. Dolinar

Maintaining ground stability in the gate roads, particularly the tailgate, has always been critical to the success of longwall mining, both in terms of safety and productivity. Several new support technologies have been developed in recent years to replace conventional wood and concrete cribbing for secondary roof support. Since their performance characteristics are unique, the best practices that have been developed with conventional wood cribbing may not be applicable for these alternative support technologies. Therefore, with so many options to consider and the importance of achieving adequate ground control at minimal cost, the trial-and-error approach to longwall gate road support is no longer prudent. This paper discusses a design methodology for standing secondary tailgate supports. This design technique requires in-mine measurements of tailgate support loading and convergence to establish a tailgate ground reaction behavior based on support and strata interaction. The methodology uses the performance characteristics generated in the National Institute of Occupational Safety and Health's (NIOSH) Mine Roof Simulator (MRS) to match the stiffness and load characteristics of various supports to the measured ground reaction behavior. It can be used to determine the appropriate application of alternative roof support systems or to design in-mine trials so that a fair and equitable comparison of different support systems can be made. A case study of the methodology at a western Pennsylvania mine site is presented in the paper, including a comparison of four alternative support technologies to the conventional wood and concrete cribbing historically used at this particular mine.

Jan 10, 2000

By J. C. W. M. de Wit

An excavation, within which a tunnel is sunk as a part of the Centraal Station underground station (platform section) of the Noord/Zuidlijn ('North/South Line'), is to be created beneath the Amsterdam Centraal ('Amsterdam Central') station. The section beneath Amsterdam Centraal Station is characterised by the application of a particular technology in the form of, inter alia, the so-called 'sandwich wall'. This is a composite wall consisting of two rows of Tubex piles with a body of jetgrout columns in-between. This wall acts both as an excavation support wall and also provides vertical bearing. The installation of the wall, including both Tubex piles and jetgrout columns, within these specific conditions (limited height, sensitive historical building), within the design requirements set in terms of construction tolerance and water and soil retention, may be regarded as being a pioneering achievement. The environmental constraints are that the trains should continue to run, the inconvenience to passengers should be kept to a minimum and the historic station should not suffer any damage. Because of the complexity of the working conditions, the project is being overseen by a steering group of experts in the specified construction processes. In order to manage the project risks, jet grouting trials were initially carried out, in order to highlight and control execution problems; the practicability of the design is then tested. Work commenced on the sandwich wall in 2003, when the wooden piles were extracted at the locations where the sandwich wall was to be constructed; in 2004, the steel Tubex piles for the southern wall sections were installed. From May 2005, the construction of the sandwich wall got under way; in addition to the described process supervision, an extensive measuring programme was established, so that the process could be adjusted as necessary and the quality of the finished product determined. This applied to both individual columns and for the end product, the sandwich wall. The measurement results were processed for each column, interpreted and the effect on the work still to be conducted was assessed for each future column. Preventative and corrective measures were, if necessary, taken in order to control or counteract the measured defect. In addition to the process-oriented and qualitative measurements, various independent measurement systems at the station building served as a further control in order to prevent damage to the building.

Jan 1, 2006

Chalcopyrite concentrate was combusted in oxygen-nitrogen atmospheres, the composition of which ranged from 1-100 per cent oxygen. Factors studied included particle size, experimental temperature and oxygen concentration. The study was assisted by chemical and X-ray diffraction (XRD) analysis and temperature measurements of single particles. Size reduction occurring after melting was found to have a major effect on the overall reaction time. Thus time to attain ignition was largely determined by the original particle size, whereas combustion time was independent of this factor. For particles larger than 40 I'm in air the time to attain ignition predominated. The maximum temperatures measured for single particles were the result of pyrite present in the concentrate. Chalcopyrite did not attain thesame temperatures. Vaporization, either as CU(g) or CuO(g) lImited the temperature. Maximum temperatures measured for single particles of pyrite ranged from 1610°C in 14 per cent oxygen to 2360°C in 100 per cent oxygen (both at 700°C). Measured temperatures were compared with those calculated from a diffusion-based model.

Jan 1, 1983