Search Documents

By Kevin W. Cargill

In September 2004, Hurricanes Frances and Ivan caused the Pigeon River in western North Carolina to flood. This flooding eroded the embankment below Interstate 40 (I-40) and sent one of the eastbound lanes, along with the roadway shoulder, into the river below the embankment. North Carolina Department of Transportation (NCDOT) needed to reopen all the lanes of I-40 as soon as possible and considered this damage to be an emergency situation. NCDOT contracted Schnabel Foundation Company to design and build a repair that would keep this important interstate open and reestablish the eastbound lane. The obstacles included limited work room, the requirement of keeping the remaining lanes of I-40 in service, and producing a final product that would be relatively maintenance free and last at least 100 years. The proposed repair had to consider that the existing interstate was founded on a rock fill that was constructed from rock blasted off the adjacent mountain side. The selected design included two, tied-back micropile walls to address these obstacles and other issues. Each of the walls were constructed of 10.75 inch diameter micropiles and corrosion-protected tieback anchors installed through the existing rock fill into competent bedrock, concrete wales, and a reinforced shotcrete facing. This successful project was completed during the coldest months of the year and within the timeframe established by the State of North Carolina. This paper will discuss the design and construction of the repair and the many challenges that had to be overcome.

Jan 1, 2006

This paper briefly describes the shaft, including sinking, steel sets and their installation, shaft equipment and winders.INTRODUCTIONThe New Broken Hill Consolidated Ltd. Service Shaft is a vertical concrete-lined circular shaft, 20 ft. in diameter with -steel sets spaced at 12-ft. centres. The diameter of 20 ft. was established as the minimum that would enable the shaft both to house the proposed hoisting and service equipment and to satisfy ventilation requirements as a downcast airway. The 12-ft. set spacing was based on South African practice in similar types of shafts.The shaft extends from the surface to 28 ft. below No. 22 Level, a total depth of 3,194 ft. Sinking was commenced in September 1946, and equipping completed in January 1955. Initially the shaft was sunk and concrete-lined to a depth of 52 ft., using a stiff-legged crane and clam-shell grab for mucking. Operations were suspended at this depth to allow the installation of the steel sinking head-frame, winders and ancillary equipment.Sinking and concreting were recommenced after four months and continued to a depth of 1,035 ft. 6 in., where the shaft connected with a pilot opening. The concrete lining was poured as sinking progressed and was piped from the surface to this depth, after which all concrete was lowered in buckets and discharged through a distributor suspended in the shaft. A cycle of stripping to the pilot opening and concreting was continued until the shaft reached No. 22 Level. From this level the remaining 28 ft. was sunk full size. All plats were cut and concreted as sinking progressed.

Jan 1, 1957

By J. P. Josien, Didier C.

ABSTRACT: France now faces the closure of most of its mining sites. Surface instability risk may sometimes remain, especially where large underground voids exist. This paper illustrates the importance of failure mechanisms identification in order to define properly how to manage the residual risk. RESUME: La France fait aujourd’hui face à la fermeture de ses exploitations minières. Des risques d’instabilités de surface peuvent persister, notamment lorsque des vides résiduels existent au sein des travaux souterrains. L’article illustre l’importance que présente la nature des mécanismes de rupture potentiels dans le choix des mesures compensatoires à adopter pour gérer le risque résiduel à long terme. ZUSAMMENFASSUNG: In Frankreich stellt sich derzeit das Problem der definitiven Schliessung des meisten Bergwerke. In manchen fällen ist die Stabilität der Oberfläche nicht garantiert, speziell wenn unter Tage nicht verfüllte Hohlräume verblieben sind. Dieser Bericht zeigt die Wichtigkeit, bei der Auswahl geeigneter Langzeit-Risikomanagementmethoden, der verschiedenen Mechanismen mit denen ein eventueller Bruch an die Tagesoberfläche geraten kann.

Jan 1, 2003

By C. Klinkenberg, G. Zhu, K. Hulka, S. V. Subramanian

A quantitative model based on strain accumulation in multi-pass rolling is developed to overcome a large critical strain for dynamic recrystallisation in a Nb microalloyed steel with high Mn content (HTP steel). The larger the critical strain for dynamic recrystallisation, the finer is the dynamically recrystallised grain size. The initial mill trial showed that it is feasible to achieve ultra-fine grain size by dynamic recrystallisation but the prevention of static recrystallisation in between passes is identified as an essential condition to suppress mixed grain size. The data-base on static softening kinetics at short interpass time was experimentally determined on WUMSI and incorporated in the model. The model is used to optimise the strip rolling schedule to prevent static recrystallisation in the interpass time. The rolling simulation of strip rolling schedule has validated the model prediction that it is possible to obtain a uniform ultra-fine ferrite grain size of about 1-2 micrometer diameter in final ferrite microstructure for industrial rolling parameters. A user friendly software package has been developed to apply the model for off-line control of mill processing parameters, i.e., time-temperature-deformation schedule of finish rolling in order to accumulate large strain to overcome a large critical strain for dynamic recrystallisation. The model is a powerful predictive tool for grain size control in multi-pass rolling.

Jan 1, 2004

By Julian Wills

The Candrill was developed with Soredem as a one-operator rockdrill for Canadian narrow vein mining. It provides the benefits of increased drilling rates, lower noise and vibration, mass reduction of 20% and system cost saving. The Candrill is to be commercialised at the end of 2001 together with a stoper drill through Parts Headquarters, Novatek's Canadian agent. The Candrill or pneumatic drills may be further exploited using a simple mechanised drilling system to further reduce operator labour, improve drilling speeds by up to 50% and to enhance drilling accuracy. Novatek's drilling system for simple mechanisation in gold and platinum mines is integrated with roof supports, can operate in stope widths as low as 800 mm and has resulted in labour savings of 50%, improved advances per blast of 20 to 50% and improved operator safety and ergonomics.

Oct 1, 2001

By R. K. Singhal

Canada is a world class producer and exporter of minerals and mineral products. Today's highly mechanized Canadian open pits use state-of-the-art equipment and support technology. They are taking advantage of larger equipment, including in pit crushing and conveying, truck dispatch systems and electronic management tools. Mine planning is computerized. Environmental issues are dealt with in all phases of planning, and equipment modifications are pursued to keep them functioning in the hostile Canadian north. In 1991, Canada's mineral production (excluding fuels but including coal) totaled $C 16.9 billion, a decline of 13.8% from the 1990 total of $C19.6 billion. It is a major producer of nickel, zinc, asbestos, potash, molybdenum and uranium. Canada is also an important source of copper and iron ore (Fig. 1).

Jan 1, 1995

By Madgwick J. C

Microaerobic biodegradation oflow-grade manganese dioxide slurry tailings was demonstrated in enrichment cultures treated with dilute molasses at 30°C and pH 5·8. Supplementary nitrogenous nutrients, yeast extract addition and pH adjustment were not required.Continuously stirred, air-limited reactors were superior to still intermittently agitated cultures, in that, at 5 per cent (w/v) MnOz tailings and 5 per cent (w/v) molasses, the yield of 0.12 g Mn++/g molasses, the rate ofleaching of 1·06 g Mn++/l/d and a recovery of Mn++ of 58 percent from MnOz were 2·8 times, 1·7 times and 1·9 times greater, respectively. The best compromise in yield (0·45 g Mn++/g molasses) and rate ofdissolution (0·73 gMn++/l/d) was at 1 per cent (w/v) molasses in a stirred reactor.Where leaching organisms were separated from sterile ore by a bacteria impermeable membrane leaching was shown to be some 20 per cent due to diffusible metabolites and 80 per cent due to a direct contact between the bacteria and the ore particle's surfaces.

Jan 1, 1986

By Diógenes Albert Gomes

Neste trabalho são apresentados os impactos físicos e mecânicos da reciclagem de insumos refratários compostos por óxidos de magnésio ligado ao carbono, visando à reutilização destes como matéria prima para a confecção de novos tijolos. Os resíduos refratários substituíram, na formulação proposta, 100% massa de MgO utilizado nestes tijolos. O estudo envolveu a confecção dos novos tijolos e a realização de ensaios de caracterização dos tijolos produzidos, através de ensaios físicos. Os resultados mostraram uma porosidade final elevada na condição sem cura, resultando em valores de densidade e resistência inferiores aos dos tijolos produzidos com matérias-primas virgens.

Aug 16, 2017

By Nick Salisbury, Alan Howard, Scott Tunison

INTRODUCTION Geotechnical investigations for tunneling projects typically use vertical test borings and, to a lesser extent, angled borings. Horizontal drilling applications were often limited to specialty testing programs and to perform probe drilling from a tunnel boring machine (TBM) as part of production tunneling. The former often involved cumbersome setups with skid rigs and cribbing in a pilot tunnel or shaft. The latter usually was limited to generic probing for rock quality and ground water conditions with no sampling. Neither yielded continuous core at production rates suitable for design and construction planning. Conventional vertical investigations still make sense in many instances, particularly for tunnels planned beneath urban settings where truck access is convenient and where the tunnel horizon is not readily accessible via a portal or shaft. However, equipment is presently available to conduct horizontal geotechnicall investigations at reasonable production rates and cost. Advantages include continuously sampling the tunneling horizon and minimizing “access drilling” to get the zone of interest at the underground construction horizon. Horizontal boring lengths of up to approximately 800 m are considered feasible and those in the range of 150 to300 m are now routine. These capabilities make horizontal borings an attractive option to consider when looking at deep tunnels beneath ridges, especially where access is limited. Fewer drilling staging sites can also mean reduced environmental impacts when investigating tunnels proposed beneath sensitive lands such as public wilderness areas. Investment in early construction packages to develop portals for investigation access and, possibly in excavating test shafts for the same purpose should even be considered. Potential benefits in the form of achieving improved overall project costs using horizontal borings exist because of the significant additional data collected in the tunnel horizon. For this reason they should be considered during the routine cost-benefit analyses generally conducted for planning geotechnical investigations for tunneling. The authors also believe that collection of such data will reduce Geotechnical Baseline Report (GBR) conservatism and lead to lower potential for

Jan 1, 2005

The Zeehan field has yielded over 190 000 tons of lead and 26,000,000 oz of silver. Moh of the production took place between the initial discovery of silver-lead ore in 1882 and 1920, and the greatest part was extracted from fissure lodes in the Proterozoic to (?) lower Cambrian rocks. It is demonstrated that the prosperity of the mines relied upon the silver content, which is apparently highest in these beds, particularly where spilitic rocks are associated with them. In contrast, galena occurring in orebodies emplaced in the Gordon Limestone is low in silver.Most of the workings are relatively shallow due in some cases to enrichment related to erosion surfaces.Fault zones within a complex anticlinal structure exposing the Proterozoic to (?) lower Cambrian formations appear to have been major factors in the control of mineralization.

Jan 1, 1968

By Met B

IN the followmg paper an account is given of work performed by the author for the purpose of sampling a slime dam on the leases of the North Mount Farrell Co. N.L., at Tullah, Tasmania, during the summer of 1925-26.For convenience the paper is divided into sections as follows:1. THE MINE2. THE SLIME DAM3. SURVEY OF THE DAM4. BORING OF THE DAM(a) INTRODUCTION(b) 1ST METHOD(c) 2ND METHOD(d) 3RD METHOD(e) 4TH METHOD(f) GENERAL NOTES5. CONCLUSION

Jan 1, 1928

By C. E. Wood

[Because of the renewed i~,ortanc of the strate ic netal ~ngane8e the Bureau of Mines is conductin further ro~aarch on pyrometallurgica1 ~ethods of boneficiating 0 ngani.foro'l iron ores nnn lo\,f-~~r de oanganesc ores. Published data on .the l2~roI'let llurgica.l treatnent of tl::1.nganse8 ores have been revi .. \-'en by Jose-ph ? .2]

Jan 1, 1940

By P. Tsang

The mechanisms and functions of yield pillar are analyzed by employing finite element method that takes time dependent and plastic failure of rock into consideration. The design criteria for different geological conditions are discussed. The results provide further evidences that yield pillar design will improve floor or roof condition, especially when the floor and/or roof strata are weaker than the coal. Based on this study, the yield pillar size is determined for one cod1 mine located in southern West Virginia.

Jan 1, 1989

By N. Demirel, O. Gölbasi

Draglines are massive machines extensively utilized in opencast mines for overburden stripping. The demanding working environment induces fractures, wear and tear, and fatigue failures in dragline components and eventuates in extended maintenance, lengthy downtimes, and loss of production. The bucket is the main source of external loads on the machinery, since interactions with ground materials take place in this region. This study aims to develop a generic finite element model of the stress on an operating bucket. This entails (i) three-dimensional modelling of a dragline bucket, (ii) analytical estimation of resistive forces in the bucket movement, (iii) three-dimensional simulation of the moving bucket using finite element analysis (FEA), and (iv) sensitivity analysis to examine the effect of formation characteristics on stress variation. Simulation results imply that the drag hitch and digging teeth are the elements of the bucket that are most prone to failure. In addition, sensitivity analysis indicates that internal friction angle of the formation is the dominant parameter leading fluctuations in stress values. Changes in stress level are least influenced by formation density.

Jan 1, 2015

By Jose Luis Sosa, Marco Surichaqui, Ramirez Marcelino

El proyecto permite obtener resultados de operación que no siempre son los esperados en cuanto a calidad y recuperación, aquí es donde destaca el programa; tiene una data que PRONOSTICA estos resultados, con el control de parámetros, corrigiendo estos resultados al valor óptimo esperado, haciendo que su empleo permita obtener en “tiempo real” excelentes resultados en cuanto a calidad y recuperación del licor lixiviado y se refleja en costos.

Sep 1, 2017

By Pierre Pelletier, Julie Fournier, Gianni Bartolacci, Yves Breau, Dominique Girard, Ahmed Bouajila, Carl Duchesne

"The development of on-stream analyzers (OSA), such as those based on X-ray fluorescence (XRF), has been key to improve metallurgical performance of flotation processes. However, since these analyzers are shared between several streams, they typically provide grade measurements every about 10-15 minutes. In general, this frequency is too long compared to process dynamics and so, implementing an efficient feedback control strategy based on OSA can be difficult. In addition, due to the limited capacity of OSA systems, several important intermediate streams are not analysed, but could provide relevant information about the state of a flotation circuit.To overcome this problem, vision systems have been developed in the past to predict concentrate grade based on froth color – this could be very useful to control flotation performance between OSA measurements. However, applications reported in the literature typically use univariate summary statistics of the full red, blue, and green color distribution of froth images, while RGB images are truly multivariate. Although, in some cases, grade prediction was achieved with reasonable accuracy, one may, by using only summary statistics, miss important information about the state of the flotation process.This paper investigates the application of Multivariate Image Analysis (MIA) concepts to flotation froth images. These techniques are based on multivariate statistical methods such as PCA and PLS, which have the ability to analyze large databases (such as digital images) and summarize the relevant information content of the data into a small number of latent variables, capturing the most important features of the images for concentrate grade prediction. The potential of application of these methods in the mineral processing industry is illustrated using a few industrial case studies."

Jan 1, 2003

By V. Gall, J. Rudolf

The Virginia Department of Rail and Public Transportation and the Metropolitan Washington Airports Authority are undertaking the extension of Washington Metropolitan Area Transit Authority’s Metrorail service to Washington Dulles International Airport and beyond to Route 772 in Loudoun County, Virginia. The roughly 37 kilometers long, double track alignment involves two 700 meters long single track, soft ground NATM tunnels at Tysons Corner, two 3.3 kilometers long single track rock TBM tunnels at Dulles Airport and one 25-meter deep station at the airport to be constructed by NATM in sedimentary rock. The design-build project is being implemented in a Public-Private-Partnership. A joint venture of Bechtel and Washington Group International has concluded the preliminary engineering and construction is scheduled to start in late 2007.

Jan 1, 2007

By William F. Daly, William H. Hansmire

Installation of initial tunnel support is often the most uncertain element of work in the design of, and a contractor bidding on, construction of a rock tunnel. The risks the construction contractor and owner assume are delineated to a great extent in the technical specifications portion of the contract documents. It is intended that this paper identify current practices for specifying initial tunnel support and the impacts each case has on the assignment of risks associated with providing the initial tunnel support. Examples of recently completed tunnel designs are given.

Jan 1, 1985

By James T. Wood

Stratigraphy, structure and closure of the Paloma field are discussed, with some details regarding the present state of development. The Paloma anticline, a large dome modified by faults, is the largest single closed dome in the southern San Joaquin valley without surface outcrop or topographic expression. It owes its discovery to geophysics. Of nine wells drilled to the Stevens sand, seven are productive. The ultimate productive area may approximate 3000 acres when the limits of the field are determined. Introduction The Paloma field derives its name from the Paloma school, ½ mile north of what is now the center of the field. The field is 17 miles southwest of Bakers-field, in the south central part of the San Joaquin Valley (Fig. I). The present developed area and its expected extensions are in townships 31 and 32S., R.26E. It is the most southerly of several fields that produce from the Stevens sand zone. The first well to produce condensate was a joint test drilled by the Western Gulf Oil Co. and The Texas Co. near the center of sec. 3, T.32S., R.26E., well No. 54-3. This well was completed on Aug. 31, 1939, at a depth of 10,178 ft. The initial production was 2280 bbl. a day of condensate and 14,750,000 cu. ft. of gas (½-hr. gauge) through a ?-in. bean. Prior to the drilling of this well, the Ohio Oil Co. discovered and developed a small gas field, which embraces a part of three townships about their common corner but lies chiefly in secs. 31 and 32, T.31S., R.26E. The first well was completed on July I, 1934, at a plugged depth of 5239 ft. after having been drilled to 7957 ft, production was found in a 59-ft. zone IIO ft. below the Fourth Mya bed, within the Sari Joaquin clays. Until recently this field was known as the Buena Vista gas field. It is now carried by the Division of Oil and Gas as the Paloma gas field. Production within the Paloma gas field is derived from six wells, producing from several different zones in the interval from 4177 to 5548 feet. Geology Stratigraphy The sediments penetrated by wells in the Paloma held range in age from Recent to Upper Miocene. The entire section, which exceeds 10,000 ft. in thickness, conforms generally to the standard section of the south central San Joaquin Valley. The producing zone, sometimes called the Paloma sand, is the approximate equivalent of the Stevens sand zone of the Ten Section, Canal, Coles Levee and other fields. The stratigraphic section is shown in Table I. Paloma Producing Zone* (Stevens Sand Zone, Upper Miocene) .-The Paloma producing zone (Fig. 2), frequently referred to as the Paloma sand, is encountered at depths ranging from 9950 to 10,300 ft. In general, it is a massive, firm to hard, not too well sorted, fine to medium fine sand. It is interbedded with thin, hard, calcareous sand shells of similar texture and cherty

Jan 1, 1942

By James T. Wood

Stratigraphy, structure and closure of the Paloma field are discussed, with some details regarding the present state of development. The Paloma anticline, a large dome modified by faults, is the largest single closed dome in the southern San Joaquin valley without surface outcrop or topographic expression. It owes its discovery to geophysics. Of nine wells drilled to the Stevens sand, seven are productive. The ultimate productive area may approximate 3000 acres when the limits of the field are determined. Introduction The Paloma field derives its name from the Paloma school, ½ mile north of what is now the center of the field. The field is 17 miles southwest of Bakers-field, in the south central part of the San Joaquin Valley (Fig. I). The present developed area and its expected extensions are in townships 31 and 32S., R.26E. It is the most southerly of several fields that produce from the Stevens sand zone. The first well to produce condensate was a joint test drilled by the Western Gulf Oil Co. and The Texas Co. near the center of sec. 3, T.32S., R.26E., well No. 54-3. This well was completed on Aug. 31, 1939, at a depth of 10,178 ft. The initial production was 2280 bbl. a day of condensate and 14,750,000 cu. ft. of gas (½-hr. gauge) through a ?-in. bean. Prior to the drilling of this well, the Ohio Oil Co. discovered and developed a small gas field, which embraces a part of three townships about their common corner but lies chiefly in secs. 31 and 32, T.31S., R.26E. The first well was completed on July I, 1934, at a plugged depth of 5239 ft. after having been drilled to 7957 ft, production was found in a 59-ft. zone IIO ft. below the Fourth Mya bed, within the Sari Joaquin clays. Until recently this field was known as the Buena Vista gas field. It is now carried by the Division of Oil and Gas as the Paloma gas field. Production within the Paloma gas field is derived from six wells, producing from several different zones in the interval from 4177 to 5548 feet. Geology Stratigraphy The sediments penetrated by wells in the Paloma held range in age from Recent to Upper Miocene. The entire section, which exceeds 10,000 ft. in thickness, conforms generally to the standard section of the south central San Joaquin Valley. The producing zone, sometimes called the Paloma sand, is the approximate equivalent of the Stevens sand zone of the Ten Section, Canal, Coles Levee and other fields. The stratigraphic section is shown in Table I. Paloma Producing Zone* (Stevens Sand Zone, Upper Miocene) .-The Paloma producing zone (Fig. 2), frequently referred to as the Paloma sand, is encountered at depths ranging from 9950 to 10,300 ft. In general, it is a massive, firm to hard, not too well sorted, fine to medium fine sand. It is interbedded with thin, hard, calcareous sand shells of similar texture and cherty

Jan 1, 1942