Search Documents

By D Crequer

Land rehabilitation at Golden Cross is reviewed, 8 years after mine closure in 1997/98, from the perspectives of a Peer Reviewer (land rehabilitation) and a Regional Council Officer (Resource Consents compliance). Land rehabilitation items we discuss include: management of restored pastures, native plantings (on-site riparian and block plantings and off-site environmental riparian enhancement plantings), wetlands (on-site tailings lake and sediment ponds littoral zone plantings, and basement of the open pit; and off-site wetlands enhancement plantings), pine plantations on-site and on surrounding land, stabilization of the Tailings Lake Embankment (landslide) and Open Pit capping, capping of acid-mine-rock, stability of discharge channels, buildings and amenities, public access for recreation, educational uses, and future management of the site. Pest control has helped to conserve the rare and endangered HochstetterÆs (Leiopelma hochstetteri) and ArcheyÆs (L. archeyi) frogs, and a regionally significant stand of rare swamp maire (Syzygium maire) has been conserved and fenced.

Jan 1, 2006

By Julien Rivard

Au printemps 2011, la Corporation minière Osisko met en production le gisement Canadian Malartic, qui devient la plus importante mine d?or à ciel ouvert au Canada. Pour lui faire place, elle a déménagé un quartier de 205 maisons et construit 6 nouveaux bâtiments institutionnels. Les démarches ont commencé en 2006. La compagnie a d?abord établi l?emplacement du nouveau quartier résidentiel, en collaboration avec la Ville de Malartic, puis fait la conception de ce quartier de manière à refléter au mieux les caractéristiques du quartier à déménager. Elle a ensuite effectué une opération d?assignation consistant à proposer à chaque propriétaire intéressé un lot dans le nouveau quartier. Au total, 140 résidences ont été déménagées en 2008 et 2009 et 65 été rachetées par la compagnie, le tout par des ententes de gré à gré sauf pour un seul cas. La réussite d?une opération d?une telle importance sociale n?a été possible que parce que la compagnie s?est assurée d?un soutien massif de la population et des autorités pendant tout le processus. Cette expérience peut être fort utile pour les nombreux projets miniers dont l?insertion dans la communauté est un enjeu important.

May 1, 2011

By James P. Sloss

A PERMANENT assay office is commonly established as part of the general plant equipment of operating gold and silver properties, but during the development stage of a mine, the cost of such an office is usually so assay work must be done elsewhere. In most instances only a few samples will be taken each day, but if the mine is to be developed scientifically, the analyses of those samples will guide further development. Under such circumstances, the time element in assay returns is important, since the lapse between the taking of the samples and the receipt of results may determine the success or failure of a small-mine operator. The following description of fur-

Jan 1, 1935

By Joaquim Luiz Monteiro Barros

Este trabalho tem como objetivo principal apresentar de forma didática e com um exemplo prático a viabilidade da aplicação da tecnologia de recuperação de calor no sinter cooler, com a finalidade de gerar energia térmica (ar quente, vapor, água quente, etc) reduzindo o consumo final de combustíveis na planta.

Aug 17, 2017

By Victor Romero, Steve Redmond

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of individual authors and are not necessarily those of the SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2011

By N. R. Paterson, D. G. MacKay

"The geology of the Mattagami mining camp, while of particular economic significance, is unfortunately obscured by a very thick mantle of overburden. For this reason geo-physical methods have been relied upon heavily in exploring the area. Geophysical data over five important sulphide discoveries show how targets are selected for drilling and how effective geophysics has been in assisting subsequent development programs."

Jan 1, 1960

By Richard Paul Seelig

The following review covers published information on pressing of metal powders at room temperature. Only those operations are considered which occur between the time the powder is filled into the cavity and the compact is ejected from the die. Thus, this review does not concern hot pressing, coining or sizing feed or flow problems, commercial presses nor designs. It was also necessary to disregard to a large extent the effect of pressing on subsequent operations and on properties after sintering. 'The pressing operation is considered independently in its function to compact loose metal powder into useful shapes which can subsequently be handled. There are some comments by the writer in connection with a few of the findings quoted in the literature in order to stimulate thought and discussion. The selection of references quoted in the text is in some cases arbitrary although an attempt was made to favor papers containing novel ideas, techniques or results which mag stimulate future research. In order to enable the reader to check further into the subjects mentioned, the original, rather extensive, bibliography is appended even though not all the references are touched on in the printed version of this review. The equipment used by various workers, for example a die design created by Bridgman,22 is very interesting. 'The die insert has a conical external surface. The vertical pressure exerted on the punch transmits itself to the die which in turn is pushed harder into its tapered retainer. Thus, the higher the pressure exerted on the punch, the higher also the pressure exerted inwards on the die inserts. Inasmuch as this pressure counteracts the internal pressure from the compact the two stresses balance each other so that it is possible to obtain tremendous pressures without breaking the die. The die collar was made from an oil hardening tool steel, heat treated to a tensile strength of some 300,000 psi. The die was closed at the bottom by a plug made from special tool steels. Bridgman found that there is no steel which will withstand a com-pressive stress of 700,000 psi without continuous slow flow or immediate fracture. Therefore, the only material suitable for use in the pressing punch was sintered carbide. In view of the ingenious design it was possible to use special tool steel as die material. Jones22 raises the question whether this method of pressing has practical application in powder metallurgy. Although these tremendous pressures cannot readily be utilized without many special precautions, the tapered die and retainer idea is believed to be useful even for lower pressures. Bridgman, himself," alls attention to the fact that the properties

Jan 1, 1947

By Richard Paul Seelig

The following review covers published information on pressing of metal powders at room temperature. Only those operations are considered which occur between the time the powder is filled into the cavity and the compact is ejected from the die. Thus, this review does not concern hot pressing, coining or sizing feed or flow problems, commercial presses nor designs. It was also necessary to disregard to a large extent the effect of pressing on subsequent operations and on properties after sintering. 'The pressing operation is considered independently in its function to compact loose metal powder into useful shapes which can subsequently be handled. There are some comments by the writer in connection with a few of the findings quoted in the literature in order to stimulate thought and discussion. The selection of references quoted in the text is in some cases arbitrary although an attempt was made to favor papers containing novel ideas, techniques or results which mag stimulate future research. In order to enable the reader to check further into the subjects mentioned, the original, rather extensive, bibliography is appended even though not all the references are touched on in the printed version of this review. The equipment used by various workers, for example a die design created by Bridgman,22 is very interesting. 'The die insert has a conical external surface. The vertical pressure exerted on the punch transmits itself to the die which in turn is pushed harder into its tapered retainer. Thus, the higher the pressure exerted on the punch, the higher also the pressure exerted inwards on the die inserts. Inasmuch as this pressure counteracts the internal pressure from the compact the two stresses balance each other so that it is possible to obtain tremendous pressures without breaking the die. The die collar was made from an oil hardening tool steel, heat treated to a tensile strength of some 300,000 psi. The die was closed at the bottom by a plug made from special tool steels. Bridgman found that there is no steel which will withstand a com-pressive stress of 700,000 psi without continuous slow flow or immediate fracture. Therefore, the only material suitable for use in the pressing punch was sintered carbide. In view of the ingenious design it was possible to use special tool steel as die material. Jones22 raises the question whether this method of pressing has practical application in powder metallurgy. Although these tremendous pressures cannot readily be utilized without many special precautions, the tapered die and retainer idea is believed to be useful even for lower pressures. Bridgman, himself," alls attention to the fact that the properties

Jan 1, 1947

"In an environment of rising energy prices and mining at greater depths, cost-efficient loading and hauling equipment is essential. Conducted at an underground mining operation, this study analyzes the energy consumption and gas emissions of diesel and electric load-haul-dump machines (LHDs) with similar bucket capacities. Based on energy prices from the first quarter of 2014, results of discrete event simulation show that energy costs for diesel and electric LHDs are US$0.24/t and US$0.07/t, respectively. Also, diesel LHDs emit 2.68 kg CO2 per litre of diesel fuel, whereas using electric machines reduces the need for ventilation to mitigate engine heat and emissions and reduces energy costs.RÉSUMÉ Dans un contexte de croissance des prix de l’énergie et d’exploitation minière à des profondeurs de plus en plus grandes, il est essentiel d’avoir des équipements de chargement et de transport les plus rentables possible. La présente étude, effectuée dans une mine souterraine, analyse la consommation énergétique et les émissions de gaz de chargeuses-navettes (LHD) au diésel et à l’électricité ayant des capacités de godet similaires. En se basant sur les prix courants de l’énergie, les résultats d’une simulation d’événements discrets montrent que les coûts énergétiques pour les LHD au diésel et à l’électricité sont respectivement de 0,24 $US/t et de 0,07 $US/t. De plus, les LHD au diésel émettent 2,68 kg CO2 par litre de combustible diésel alors que les machines utilisant l’électricité réduisent le besoin de ventilation pour atténuer la chaleur des moteurs et les émissions en plus de réduire les coûts énergétiques."

Jan 1, 2015

By Paul Billingsley

THE development of the North Lily ground, which lies in the East Tintic district, Utah,. about half a mile northwest of the famous Tintic Standard mine, was undertaken by the International Smelting Co. on purely geological reasoning. The geologic theory on which this work was based resulted from several years' intensive study of the East Tintic district by the geological department of the International Smelt-ing Co., who were, during this period, indebted to many for valuable suggestions that were adopted and became part, of the gradually maturing concept. For example, E. J. Raddatz, president of the Tintic Standard Mining Co., first called attention to the significance of rhyolite alteration; J. W. Wade, assistant manager, contributed greatly to our knowledge of the great Tintic Standard orebodies; and so on all along. the line. In short, the ultimate theory embodies the aggregate experience and thought of all those most familiar with the area in question. The problem in brief was this: is the Tintic Standard deposit an isolated occurrence of ore, or are other ore deposits to be found in the vicinity? If the latter is the case, where can these others be looked for? The difficulty of the problem lay in the fact that most of the area is covered by rhyolite; beneath which lies the limestone in which the orebodies occur; so that the available evidence as to the structure of the formations, and, their mineralization; is of the slightest. The sav-ing features of the case, by means of which it proved possible to solve the problem, are three in number first, the rhyolite is pre-mineral and hence has been exposed to alteration by the mineralizing agencies; second, certain persistent dikes and fissures are con-tinuous through the rhyolite into the limestone below; and third, the extensive underground workings of the Tintic Standard gave a good basis for study of the sub-rhyolite structure and the occurrence of ore. The rhyolite overlies the Tintic Standard orebodies, and over them shows a large patch of brownish altera-tion. This patch proves to be due to chloritization and sericitization, which has spread out from certain zones of dikes, pebble-dikes and fissures. The dikes are com-posed of a light fine-grained rock which has been altered to an aggregate of quartz, alunite, and magnetite. They can be traced southwest to a common center in Big Hill, the entire mass of which is composed of the same material. The pebble-dikes, which consist of a mass of rounded pebbles, mainly quartzite, in a matrix ranging from the same quartz-alunite-magnetite rock as above to almost pure vein quartz, are closely asso-ciated with these light dikes, but in general extend farther northeast. They thus represent a specialized phase of the intrusive action of which Big Hill is the center. The brown chloritized rhyolite, then, is an alteration product due, in all. probability, to emana-tions closely associated with this phase. Since it coin-cides geographically with the Tintic Standard area of highly altered limestone, with its many great ore-bodies, it has been concluded, that it is the expression in the rhyolite of activities which have also altered and mineralized' the underlying limestone.

Jan 4, 1927

By Joshua Hoffman, Braden Lusk, John Rathbun

A Flyrock Prevention Taskforce was established in Kentucky with the support of Kentucky's Department of Natural Resources, Kentucky's Explosives Industry, and the University of Kentucky. This paper presents the initial work of the Flyrock Prevention Taskforce towards its missions of identifying the root causes of flyrock incidents based on the analysis of previous events, and tracking the progress of flyrock elimination in the future. Work identifying root causes of flyrock events is presented through the development of a database which manages information about the blasts which caused flyrock. This data includes: blasting and seismograph records, drill logs, videos of the event when available, company notes/incident reports, and any additional information regarding probable cause. Work tracking the progression of flyrock elimination efforts is presented in this paper through the introduction of a flyrock index. Several metrics are proposed for this index, and are discussed for their appropriateness and shortcomings. In order for these indexes to be valid forms of tracking flyrock incident rates additional records must be kept and reported, such as the annual consumption of explosives by surface coal blasting. Suggestions for record keeping, flyrock investigation practices, and means of tracking flyrock incident rates are proposed in this paper.

Jan 1, 2013

By C L. Briend, O&apos

This paper presents the main features of coal mining in Japan, as determined by the author while attending the International Coal Conference in October of 1963. The general economy of the country is considered, and the requirements for coking coal are outlined. Statistics and comments on production and consumption are then given, with accompanying cost figures, and the characteristics of Japanese coal mining are compared with those of Canada. Mining methods and underground transportation are covered, with emphasis on undersea mining. Finally, a description is given of a visit to the Miike colliery, the largest in Japan. I T was my privilege to attend the International Coal Conference held in Tokyo in October, 1963, to meet many prominent members of the Japan Coal Association and to visit one of the major coal fields. This is probably the reason why I was asked to present this review of the coal situation in Japan. In doing so, it must be pointed out that I am not an expert in coal mining, that my

Jan 1, 1965

By W. W. Roepke

The Bureau of Mines has developed an interactive computer program that enables mine operators and others to identify the effect of cut-ting system changes on relative dustiness at the face. The program, which simultaneously evaluates machine parameters, coal seam parame-ters, and operator-controllable parameters, was developed for use on any microcomputer using BASIC programming language. The program allows the user to change one or more of the cutting system parameters at a time to see how these changes affect relative dustiness. A complete program listing and flowchart are included along with operating in-structions and sample outputs. An example showing how to use the program is also included.

Jan 1, 1985

By Joseph Jensen

MANY fields have been zoned by nature with shales and intermediate waters between oil zones. Limitations thus imposed have been the basis on which the field was developed. In contrast thereto, in the Ventura Avenue Field, nature proved more generous. Always expecting to find such similar limitations, operators drilled deeper and deeper into the oil zone without finding any distinctive shale bodies other that the Gosnell shale and only one intermediate water, which became the point below which the final water shut-off of each well was made. Thus, on top of the structure, about 3300 ft. of oil-bearing zone has been penetrated below this intermediate w9ter-a distance of 4000 ft. below the Gosnell shale. At first it seemed that the greater the penetration in the zone, the better the well. The error of this assumption became evident

Jan 1, 1930

By AIME AIME

WITH the recent increase in the price of gold, its economic recovery at depths formerly considered impractical has become a present possibility. Two important difficulties must be met: pressure bursts of the rock, and the reduced efficiency of human labor subjected to the higher temperatures and the increased humidity at the greater depths. In the following abstract of a paper by J. H. Dobson, presented before the South African Institution of Engineers on

Jan 1, 1935

By Gordon R. Sima

The contract is concerned with feasibility studies, design and fabrication of a group of prototype hand-held test instruments and machine-mounted test instruments for measurement of electrical shock hazards of mining machines. An instrument for use in open pit mining machine ground wire verification was proposed, developed, built, and tested. This report presents the design and operational theory of the open pit instrument as well as information on the program to improve the original prototype hand-held machine-mounted test instruments.

Jan 1, 1977

In 1990, the Bureau of Mines (BOM) conducted a mineral investigation of the mines and prospects in the East Mojave National Scenic Area (EMNSA), San Bernardino County, California During field work, BOM identified 701 mines and prospects in EMNSA for which the geology, mineral resources, and mining history were compiled and summarized. Analytical results for 1,188 rock samples collected are tabulated. Total value of identified resources in EMNSA is $5.0 billion. Twenty-four mines and prospects were deemed profitable under current economic conditions. Development could generate considerable economic benefits to San Bernardino County. Potential economic benefits from mining the deposits were evaluated under the following access restrictions for EMNSA: 1) full access, 2) HR 3460, and 3) S 11/HR 780. Under the full access scenario, cumulative mine revenues are $3.0 billion, cumulative personal earnings at mines and supporting industries are $0.94 billion, and annual jobs at mines and supporting industries are 2,379. Under HR 3460, mine revenues, personal earnings, and annual jobs are $2.9 billion, $0.88 billion, and 2,165, respectively. Under S 11/HR 780, mine revenues, personal earnings, and annual jobs are $1.0 billion, $0.32 billion, and 936, respectively.

Jan 1, 1990

By J. C. Thornley

Service failures of seemingly conventional galvanized bolts, in normal operation, on transmission towers in New Brunswick have been found to be the result of hydrogen cracking. In both these cases, similar failures elsewhere can be avoided by suitable clauses in the purchase specifications. In the first case described, the manufacturing procedure was responsible for strengthening and embrittling a standard, soft, constructional steel. In this case, a fracture mechanics analysis predicted critical crack depths for final fracture very similar to those found in practice. This case reveals an apparent cooperative connection between hydrogen embrittlement and strain ageing in plain carbon steels. In the second case described, the steel was simply a high strength steel which should not have been made into galvanized bolts.

Jan 1, 1979

By J J. Boshoff

This iron ore mine site, located in the Pilbara region of Western Australia, commenced operations in 1998, with ore derived by mining of open-cut pits in Channel Iron Deposits (CIDs). A portion of the ore extracted at the mine is processed at wet processing plants that produce both ore saleable product and waste fines (i.e. tailings) slurry. The waste fines produced at the wet plants are presently stored within Waste Fines Cells (WFCs).Waste fines cells A (WFCA) and B (WFCB) are located within an Autonomous Haul System (AHS) area and consist of embankments that span the width of the pit in east-west alignments. Technical studies and design analyses were carried out to support embankment raises and ongoing development of the WFCs. During operation and development of the WFCs, a multitude of simultaneous activities took place to the immediate north and south of WFCA respectively. These activities included the construction of the embankment raises using the AHS fleet, mining of the CID to not only mine the ore but to also create future deposition space for WFCB, blasting next to the WFC embankments as part of the mining activities, seepage collection and dewatering of the pit in the vicinity of the WFC.This paper discusses the material characteristics, design approach, construction staging and equipment requirements, blasting near embankments, water management, facility consequence category and closure concept.CITATION:Boshoff, J J, 2018. A waste fines cell with a multitude of concurrent activities, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 39–49 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By A. Yazadni-Chamzini

Considering the nature of open pit mines, harvest volume, it usually is required to remove a lot of waste to access to mineral planned grade. So, one of the most important part of open pit mines design, is waste dump site selection. Many factors are effective in waste dump site selection. These factors are sometimes in conflict with each other. So selecting the desired location for waste dump is a process complex and multi-criteria decision making. There are a variety of methods for decision making under complicated condition, such as fuzzy, Delphi, multi-criteria decision making and Expert system methods can be hinted. VIKOR method, which is one of the decision making multi criteria methods, is useful tool for decision-making. On the other hand with regard to uncertainty in decision-making, fuzzy approach is a useful tool for this purpose. This article has tried to select the best waste dump site in Sari Gunay Gold Mine by Fuzzy VIKOR. The results show that C position has a higher priority than other positions.

Jan 1, 2012