Search Documents

By Jean R. Garcia, Paulo J. R. Albuquerque, Renato P. Cunha, Osvaldo Freitas Neto

"Abstract Results obtained from in-situ load tests carried out on drilled displacement piles sunk in a porous, lateritic and unsaturated soil deposit, are analyzed in this paper. Three slow-maintained load tests were performed on deep instrumented piles with a diameter of 0.37 m and around 12 m long. The soil deposit consists of a superficial, silty clay “porous” layer 6 m thick, with an average standard penetration blow count (NSPT) of 4 and cone tip resistance and sleeve friction (qc and fs) of 1.5 MPa and 48 kPa, respectively. Under this layer there is a residual stratum 10 m thick, geotechnically consisting of a “porous” clayey silt with an average NSPT of 7 and qc and fs of 2.4 MPa and 202 kPa, respectively. The water table was reached at a depth of 17 m below ground level. The results of the field load tests yielded a maximum pile load (average for the tests) of 1428 kN, which is twice as high as corresponding experimental values from standard bored piles with similar geometric conditions. Exhumation of one of the tested piles was carried out after the test, in order to check integrity and shaft conditions. Numerical finite element analyses, using the commercially available French Code LCPC Cesar®, were performed in order to back-analyze the geotechnical soil parameters for a post execution pile condition. The results permitted a better understanding of the improvement of the subsoil given the intrinsic execution characteristics of this particular pile. It was also possible to note that drilled displacement piles have great potential to become an economically viable solution in tropical soils, given the enhanced behavior of such piles when compared to alternative (cheaper) techniques. In fact, it has several advantages which should make it a key foundation type in the Brazilian market in the future.IntroductionMost buildings in tropical soils use, as the main type of foundation, deep bored or auger type piles. These types of foundations can be performed in various ways, for example with or without soil extraction, with or without bentonite mud and so on. Two main processes maybe formulated: the first execution process is typified by bored pile types, continuous flight auger piles etc., which do not cause excessive soil displacement during excavation. With respect to the second process, one could mention, amongst others, driven piles (precast concrete or steel), Franki piles and drilled displacement piles, which do displace the soil during excavation by pushing the soil laterally around the hole in order to allow either the penetration of the pile or the excavator auger."

Jan 1, 2014

By Douglas Kathol

Coal in the 1990?s Exit of the integrated oil company [Shell Arco Mobil Exxon Mapco Kerr McGee Hansen Nerco Sun] Continued decline in coal prices Significant mergers & acquisitions (M&A) activity ?Most properties traded, some twice ?Significant consolidation ?Massive recapitalization ?New industry leaders ?Frustrated expectations

Jan 1, 2002

By L. A. Cramer

Platinum metal was first utilized by the Inca civilization in South America where it was found in alluvial deposits along the San Juan and Atrato rivers that lie between the Andean mountain range in Colombia and the Pacific Ocean. The nuggets found in these rivers average between 77% and 86%platinum, 7%?8% iron and small amounts of copper, gold and other Platinum Group Metals (PGMs). The Incas often alloyed platinum with copper to increase its workability and fabricated various ornaments from it.

Jan 1, 2001

By C. G. Buttleman, W. C. Brice

In Minnesota, reclamation of active aggregate mining sites is primarily regulated through local permits issued at the county, township, or municipality. However, for abandoned or depleted aggregate mining sites, a responsible party for reclamation is often no longer available. Since 1995, the Minnesota Department of Natural Resources has reclaimed several abandoned aggregate sites using innovative public/private partnerships and emphasizing native plant materials. The purpose of these projects is to demonstrate cost effective reclamation methods that can be utilized by both aggregate operators and local government and to promote mine planning and resource identification as it relates to reclamation.

Jan 1, 2000

By B. Asbury, M. Cigla, C. Balci

The Western Mining Resource Center (WMRC) at the Colorado School of Mines (CSM) received a grant from the National Institute for Occupational Safety and Health (NIOSH) to perform a study that will help reduce the amount of respirable dust generated from the cutting of coal. The study is based upon laboratory testing and field experience. This information is being used to develop a new cutterhead design in conjunction with Joy Mining Machinery. The new cutterhead design is being evaluated with existing computer models developed at CSM. The new continuous miner cutterhead will be tested at the Twenty Mile Coal Company’s Foidal Creek Mine. Baseline testing with the current cutterhead will also be performed. This paper presents laboratory test results, design methodology, and test results performed to date.

Jan 1, 2002

By S M. Iveson, K P. Galvin, D Kumar

Dry separation of iron ore fines and other heavy minerals has previously been achieved using one of two main approaches. The first is an inclined table with an upward airflow via small holes to help form an autogenous dense medium. The second is based on fluidised beds comprising a dense medium formed by fine particles suspended in an upward flow of air. In either case, vibration can be introduced. This paper describes recent findings using a novel system referred to as the Sink-Hole Fluidiser, which utilises elements of both these two former approaches. This device consists of a conventional gas-fluidised bed of fine medium with a 1 mm aperture mesh located at the surface. This mesh contains relatively large holes that act as sink-holes. The fluidised media flows upwards through the sink-holes and then falls back into the fluidised bed via the fine apertures in the mesh. The particles being separated, which are much larger than the fine media, pass over these sink-holes, where they either sink or float. The sink-holes offer a more precise balance of forces, applied on a single particle basis, resulting in robust density separation.Experiments have been performed using 2.0–4.0 mm tracer particles of density varying from 2.4 to 4.8 relative densities (RD) separated in a 200 mm diameter Sink-Hole Fluidiser with a single 13 mm diameter centrally-located sink-hole. In this preliminary semi-batch work, it was found that the Sink-Hole Fluidiser was able to achieve sharp separations (Ep as low as 0.20). This work underpins the development of a new continuous steady-state Sink-Hole Fluidiser, applicable to the dry separation of iron ore fines.CITATION:Kumar, D, Iveson, S M and Galvin, K P, 2017. A novel sink-hole fluidisation method for dry separation of iron ore fines, in Proceedings Iron Ore 2017, pp 221–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By D. Kruse

Top down constructed large diameter (up to 90 m [300 ft]) shaft design and constructability issues present an interesting suite of challenges and opportunities highlighted in this paper. The study covers 2D and 3D finite element models used to: analyze various failure modes, evaluate the shaft liner and internal structures? response to seismic loading, assist in segment design, and assess final structural design tradeoffs. Efforts to achieve economic advantage over conventional heavy civil practices have prompted innovative solutions for ring and segment design, ring build assembly, and annulus backfill grouting. Intended for soft ground conditions, relationships between soil parameters and structure design are also explored.

Jan 1, 2011

By M. van Elp, R. Saitua Nistal, P. J. M. Groot

Demand for construction raw materials depends on investment in housing, other buildings and infrastructure. The provision of these materials requires early knowledge of future trends in construction investment. By using scenarios possible future developments and bandwidths can be explored. Policy makers in government organisations as well as in the private sector can base their policy decisions upon these insights. In this paper we discuss the case of sand and gravel in the Netherlands. We will show that, depending on the future role of government and the degree of internationalisation, the long term demand for construction raw materials will strongly diverge. Nevertheless there are some common developments such as a decreasing population growth, a smaller share of the labour force in total population and a growing wealth. In different scenarios we will encounter different conditions for minerals provision and for sustainable development.

Jan 1, 2011

The recovery of coarse particles has been widely recognized as being limited by the froth in mineral flotation. In response to this, FLSmidth has developed the Selective Froth Recovery (SFR) System. The SFR System is an extraction system that vacuums material from select locations within the froth and separates the recovered solids into coarse and fine fractions with a hydrocyclone. The SFR is supported and located by an actuator connected to the cell?s level control so that the suction heads are maintained at an offset distance from the slurry level. This can increase the recovery of coarse material by selectively recovering the material close to the bottom of the froth where drop-back of coarse particles typically takes place. The SFR System has been tested at two separate mine sites, and has been proven to increase the copper recovery in both trials. TEST RESULTS The SFR prototype was installed in a copper recovery circuit, on a rougher scavenger 160-m3 flotation cell. Figure 1, shows the SFR System, which consists of four conical skimmer heads that are plumbed together and share a common actuator. The SFR System, raised out of the froth prior to a test, can be seen in Figure 2. The SFR prototype was able to maintain a variety of set points using the level control to determine the slurry height.

Feb 27, 2013

By Mohammed Sakr

The use of helical piles as a deep foundation option has considerably increased in the recent years to support a variety of loads, from small loads for several applications such as residential housing, solar farms, utilities and retrofit projects, to large loads for many applications such as commercial, power transmission lines, oil facilities and industrial applications. Therefore, it is necessary to qualify and quantify their axial capacities and performance characteristics. This paper presents the first full-scale axial compression and tension (uplift) testing program executed on large capacity helical piles installed in cohesionless soils. A total of eleven pile load tests using either single or double-helix piles with shaft diameters that varied between 324 mm to 508 mm (12¾ in to 20 in) were carried out, including seven axial compression tests and four tension (uplift) tests. The results of the axial compressive and tensile pile load tests as well as field monitoring data of helical piles installed in dense sand are presented in this paper. Based on the results of this study it was found that helical piles have developed significant resistance to axial compressive loads up to about 2920 kN (656 kips) and tensile loads up to 2900 kN (652 kips).

Jan 1, 2011

Prominent among the ore minerals at Mt. Ellison, in the Brock's Creek district, Northern Territory, are a number of copper-bismuth sulphides wittichenite, aikinite, emplectite, in association with nativebismuth, chalcopyrite, bornite, chalcocite, sphalerite and linnaeite.Linnaeite and aikinite formed first and were followed by native bismuth. Wittichenite was later and substantially replaces earlier minerals. Replacement of aikinite by wittichenite has produced secondaryor reaction bismuth.INTRODUCTIONThe Brock's Creek district of the Northern Territory lies to the south east of Darwin and has been the locale of intermittent mining of small but rich deposits of diverse ore type. Gold, tin, and copper ores were recovered especially between 1890 and 1910 with minor exploitation up to the present time. Copper ores were of prior importance, the main production coming from supergene enriched deposits of chalcocite.The mines are situated in strongly folded Precambrian strata comprising slates, sandstones, volcanics and amphibolites with replaced haematitic rocks (Sullivan, 1953). The strata in the Brock's Creek area immediately north of the Darwin-Birdum railway line are domed around a roughly circular granitic mass some 5 miles in diameter. The Mount Ellison mine is located near the N.E. margin of the granite in metamorphosed basic country rock.Study of a series of polished sections from Mt. Ellison revealed the presence of linnaeite, chalcopyrite, bornite, aikinite, wittichenite, emplectite, bismuth, sphalerite, and chalcocite. With the exception of sphalerite and emplectite each of these minerals is prominently developed and intimately intergrown with the other constituents.

Jan 1, 1963

By J. R. Thoenen

Profits in the crushed-stone industry, as in any other, represent the difference between selling price and production cost. When consumer demand increases rapidly, as occurred in the crushed-stone industry from 1918 to 1927, selling prices tend to rise. Cost of production usually rises, also, owing to the expense of expanding facilities, searching for and developing new quarries, and purchasing, installing, and operating new equipment. Frequently, also, the inattention of managements to the details of operating costs is responsible for their increase. This is not due to negligence but rather to the necessity of confining attention to the problems involved in producing material to supply orders. When market conditions change and consumer demand becomes stabilized or contracts, the producer's attention usually is directed to assuring the orders necessary to keep his enlarged facilities busy. Hence, competition increases and soiling prices decline.

Jan 1, 1939

By S. H. Jason Choi

The Systems Conveyance and Operations Program (SCOP) is being implemented to convey tertiary-treated effluent to Lake Mead near Las Vegas, Nevada. The Reach 3 Tunnel Project is part of SCOP. The tunnel?s planned location along and across the Las Vegas Wash creates challenging tunneling conditions. A number of feasible excavation and initial support methods are being considered during the final design stage. This paper describes how the tunnel construction options were refined based on anticipated tunneling conditions and compatibility between tunnel excavation and initial support methods. A brief description of the most significant characteristics of the anticipated ground conditions is included for the purpose of discussion.

By Anthony J. Konya

"This paper was written during part of the author’s student co-op with Cargill Salt at its Avery Islandunderground salt mine in Louisiana. Blasting salt is a unique type of blasting that is different than blasting other rock types. The plastic nature of salt, along with its large swell factor make salt a challenge to blast. The Cargill salt mines use and have tested a variety of different methods for breaking salt in an efficient manner, however these blasting methods are rarely used in other operations nor talked about today."

Jan 1, 2016

By R H. Sillitoe

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Geological concepts are employed routinely in porphyry copper exploration at the area selection, prospect appraisal and deposit definition stages. Regional, district-scale, deposit-scale and laboratory-based concepts can all play a role, with the resulting porphyry copper models providing templates for the integration of geochemical and geophysical responses and interpretations. Of the 19 concepts and parameters selected for brief discussion, those relating to subdivision of porphyry intrusions, understanding of diverse and commonly complex alteration-mineralisation patterns and lithocap characterisation are undoubtedly the most influential in exploration. Several of them are of particular importance because of their role in promoting grade development. Additional belt-, district- and deposit-scale features are currently little used but hold promise, whereas others have less practical value but help in underpinning the evolving porphyry copper genetic model.CITATION:Sillitoe, R H, 2015. Recent advances in porphyry copper geology and their exploration utility , in Proceedings PACRIM 2015 Congress, pp 35–44 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Peter A. Adcock, Rob Fraser

Interest in monitoring nucleation overpotential in electrometallurgical processes dates back some 40 years or more. Conversely, remarkable progress has been made in recent years on describing in detail the processes involved in the formation of thin films by electrodeposition. The newer body of work underscores a need for greater clarity in speaking about the role of nucleation and in the acquisition and interpretation of nucleation overpotential measurements – the aim of this paper. In electrometallurgy, it is generally desirable to form deposits that remain smooth, compact, and relatively fine-grained while the deposit grows to a thickness on the order of 5-10 mm, about 100 times thicker than technological thin films. Hence, we distinguish two kinds of nucleation that can result in formation of new grains:- (1) initial nucleation (onto the substrate surface) of islands that coalesce into growing deposit, and (2) ongoing nucleation of new grains on the deposit surface long after the substrate has been covered and ceases to have a direct influence. Nucleation overpotential of the first type should be measured on an electrode surface truly representative of a real industrial substrate. The second type requires judicious choice of electrode material – an “ideal foreign substrate”. In general neither the industrial substrate nor native metal to be deposited is suitable for measurement of the second type of nucleation overpotential, because of interference by other processes. For the future, clear terminology is needed to distinguish these two types of nucleation potential. The second is the one for which the type of plot dubbed by Moats and Derrick as an “Adcock plot” and by us as a “Kerby-Adcock plot” was first conceived and correlated with relatively thick zinc electrodeposits. The data of Moats and Derrick showing trends for copper electrodeposition on stainless steel and on copper electrodes are interpreted within this framework.

Jan 1, 2016

By David Smith, Bernie Martin

The Queens Bored Tunnels consist of 11,000 feet of 19'-6" inside diameter tunnels mined through rock, mixed face and dense glacial till, constructed with bolted gasketed one pass reinforced concrete liner. The tunnels are to be excavated with a pressurized face TBM, either EPB or slurry. The construction of the tunnels will require ground stabilization in the mixed face area, instrumentation and monitoring of railway infrastructure, underpinning of bridges, relocation and protection of utilities, demolition of some industrial buildings, construction of open-cut approach tunnels and emergency exits and vent plants. The purpose of this paper is to describe the scope of work, the suggested methodology and the proposed construction schedule.

Jan 1, 2005

By B. G. Tarasov

This paper proposes the further development of a recently identified shear rupture mechanism (fan mechanism) that elucidates a paradoxical feature of hard rocks ? the possibility of shear rupture propagation through a highly confined intact rock mass at shear stresses that can be significantly less than frictional strength. In the fan mechanism, failure is associated with consecutive creation of small slabs (known as ?domino blocks?) from the intact rock in the rupture tip, driven by a fan-shaped domino structure representing the rupture head. The fan head combines such unique features as extremely low shear resistance, self-sustaining stress intensification, and self-unbalancing conditions. Consequently, the failure process caused by the mechanism is inevitably spontaneous and violent. Physical and mathematical models explain unique and paradoxical features of the mechanism, which can be generated in primary ruptures and segmented faults. The fan mechanism provides a novel point of view for understanding the nature of spontaneous failure processes, including shear rupture rockbursts. The process explains, in particular, features of shear rupture rockbursts such as activation at great depths, generation of new shear ruptures in intact rock mass, nucleation of hypocentres at significant distances from the excavation, shear rupture development at low shear stresses, and abnormal rupture violence.

Jan 1, 2014

By W. Mbhalati

"Conzal Mine was not meeting production targets in 2013, and it was established that this was caused by the inability of the load haul dump machines (LHDs) to tram the required tonnages. An investigation of the LHD productivity was therefore conducted to identify the inhibiting factors. This was accomplished by carrying out a literature review on LHD operations to gain in-depth knowledge and conducting observations in the working environment. The relevant information and data on the LHD type used at Conzal was also acquired.The major inhibitor was found to be excessively long tramming distances in all the sections of the mine. The one-way tramming distances were all significantly greater than the 90 m set in the mine’s code of practice (COP), with the Main Shafts section having the longest average one-way tramming distance of 260 m. The other inhibitor was LHD utilization, which in 2013 was only 47% against a target of 70%. Simulation of the LHD operation, taking these two factors into account, showed that production could be increased by more than 100%. As a result, it was recommended that conveyor belts should be extended regularly in order to keep tramming distances within the recommended one-way distance of 90 m. In addition, utilization can be improved by minimizing employee absenteeism as well as by modifying the travelling routes such that LHDs do not encounter unnecessary delays.Paper written on project work carried out in partial fulfilment of BSc. (Mining Engineering)"

Jan 1, 2015

By F. B. Samani, B. Stabel

The 1,000 MW Hydro Power Station Masjed-e-Soleiman (formerly called Godar-e-Landar) in Iran is under construction since 1992. The rock engineering aspects of the major underground structure, i.e. the powerhouse cavern shall be reported on in detail. The geotechnical investigations are described and results given. The results of several geotechnical analyses are presented. The designed and executed rock support is given. A description of the monitoring systems and typical measurement results obtained during and after excavation are presented. The lessons learnt during construction of the Stage-I powerhouse cavern were applied on the extension of the powerhouse cavern, which is to house an additional 1000 MW. Details regarding the unexpected behaviour of the Mudstones are given. Die 1000 MW Wasserkraftanlage Masjed-e-Soleiman (vormals Godar-e-Landar genannt) befindet sich seit 1992 in Bau. Dieser Artikel berichtet im Detail über die felsbaulichen Aspekte der Untertagebauwerke, insb. der Maschinenkaverne. Die geotechnischen Untersuchungen werden beschrieben und deren Ergebnisse wie die Ergebnisse verschiedener Berechnungen werden präsentiert. Die geplante und die ausgeführte Felssicherung wird angegeben. Die eingebauten Überwachungseinrichtungen werden beschrieben und typische Ergebnisse während des Aushubs und danach werden dargestellt. Die Erfahrungen beim Aushub der Kaverne der Stufe I wurden beim Entwurf der Kaverne der Erweiterungsstufe II, die weitere 1000 MW beherbergen wird, berücksichtigt. Details zum unerwarteten Verhalten des Schluff-/Tonsteins werden angegeben. La centrale hydroélectrique de Masjed-e-Soleiman (dénommée anciennement Godar-e-Landar), d’une puissance de 1.000 MW, est en construction depuis 1992. Un rapport détaillé sera présenté sur les aspects relatifs à la construction en enrochements de l’aménagement souterrain principal, à savoir la caverne abritant la salle des machines. Une description des investigations géotechniques réalisées y est fournie ainsi que les résultats correspondants. En outre sont présentés les résultats de plusieurs analyses géotechniques. L’ancrage dans la roche tel que projeté et réalisé est présenté. Une description des systèmes de contrôle ainsi que les résultats de mesures typiques obtenus au cours des travaux d’excavation sont donnés. Les leçons tirées lors de la construction de la Phase 1 de la caverne de la salle des machines furent appliquées à l’extension de la caverne de la salle des machines, qui doit abriter une unité supplémentaire d’une puissance de 1.000 MW. Par ailleurs, des détails sont donnés sur le comportement inattendu des argilites.

Jan 1, 2003