Search Documents

By S Vianna, K Caldwell, R Silva, T Olson, D Bell

Studies to enhance the FLSmidth forced air machine through changes in the design, showed important improvements through changes in the number of Rotor blades, stator designs, rotor air distribution and other designs features. The main outcomes from this study highlighted that increasing the number of rotor blades increased the selectivity while decreasing power requirements while stators with slots have better results in terms of recovery, flotation efficiency and selectivity than without slots.Also the rotor air distribution makes a difference in the design when comparing different distribution criteria whilst keeping all features of shape and number of blades etc constant. At the most efficient rotor air distribution design, copper recovery reached one of the highest values while keeping good selectivity. The possible explanation for that is the increase in the pump capacity indicated by the increase in the specific power.It was seen as significant that reduction in specific power for some designs tested compared with the then current standard design had an average of 30% less power consumption.As a result, FLSmidth was able to identify new designs that decreased power and improved recovery, as well as, identifying some designs that specifically improved fine and/or coarse particle recovery.CITATION:Silva, R, Caldwell, K, Bell, D, Olson, T and Vianna, S, 2013. FLSmidth flotation developments - Dorr Oliver machines, in Proceedings MetPlant 2013 , pp 413-430 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By M. G. Zabetakis, T. D. Moore

The use of a partially slotted 6.5-inch-inside-diameter vertical pipe to remove methane from a longwall gob area at a depth of 2,260 feet in the Pocahontas No. 3 coalbed ms investigated. The value of gas removed by such a pipe under free-flow conditions was found to equal the cost of the installation in this case. Approximately 25 percent of the available methane passed through the pipe without the use of an exhauster; an additional 10 percent was removed when an exhauster was employed. The diversion of methane through a vertical slotted pipe to the surface permitted the use of increased mining rates and decreased the ventilation air requirements.

Jan 1, 1972

By A. Noble

Traditional simulations of mineral processing circuits are solved by straightforward numerical techniques which require iteration to accommodate recirculating loads. Depending on the complexity of the simulated circuit, this solution technique can be inexact, computationally intensive, and potentially unstable. In this communication, an alternate calculation approach is presented, wherein an exact analytical solution is determined as a function of the individual units? separation probabilities. All the stream data, including recirculating loads, may be solved simultaneously, negating the need for iteration. Furthermore, with an analytical solution available, circuit analysis may then be utilized to diagnose the relative separation potential of the circuit. By integrating these tools, the authors have developed a software package for evaluating circuit configurations. This paper presents the theory, development, and limitations of the software?s methodology along with industrial examples which highlight the tool?s applicability to industrial circuits.

Jan 1, 2012

The flolation behaviour of some Australian uranium ores was investigated. Although uraninite and pitchblend float readily with fatty acids, selective concentration to produce an economically discardable tailing has not yet been achieved. This is attributed to the presence in the ores of a quantity of uranium mineral in finely dispersed form which is very difficult to liberate. For some of the ores, at least, the proportion of this material decreases with increase in head assay.Flotation may be a useful concentrating method for some Australian ores if uranium oxide is to be sold in a free competitive market.

Jan 1, 1967

By Roberto Vargas

"El presente Trabajo de Investigación, tiene por objeto describir la tecnología, la operación del Proceso en la Planta que implementa dicha tecnología así como los resultados obtenidos en dicho Proceso y aplicaciones de la tecnología a otros tipos de concentrados de cobre (Enargita). "

Sep 1, 2017

Geometallurgical Study of Copper Oxide Mineralisation Hosted in Gravels of Different Physical Quality

Sep 13, 2010

By Robin B. Dill, Mark Pelletier, Daniel J. Dobbels, Subodh Bhaumik, Daniel J. VanRoosendaal

Although primarily cut-and-cover excavations are required for replacement of the existing elevated I-93 interstate highway through the heart of Boston for the Central Artery/Tunnel (CA/T) project, some mined tunnel construction was also undertaken. The mined tunneling conducted was the 22-m-wide northbound roadway structure which passed below a 20-m-deep operating underground subway station that was built in 1913. The innovative underpinning scheme used to support the subway station during construction resulted in the successful mining beneath the subway station with negligible vertical settlement. Two grouting galleries were carefully mined below the subway structure, and pre-grouting of the granulary, pervious glacial soils and weathered bedrock was carried out from these galleries. The reinforced concrete walls of the underpinning structure were constructed within three stacked drifts that were sequentially mined below each grouting gallery. After 11 cross adits were mined between the grouting galleries, cast-in-place post-tensioned girders that spanned between the stacked-drift walls were constructed to support the subway station. The stacked-drift walls also provided lateral support for the 22-m wide by 29-m long by13-m high opening beneath the girders.

Jan 1, 2001

By Carl Johnson, D. R. Todd

The Blue Ridge Low Level Outlet (LLO) was a design/build contract to provide a secondary means of discharging water from the Blue Ridge Reservoir. The project involved driving a 3.25 m (11 ft) modified horseshoe tunnel by 293.5 m (963 ft) long utilizing conventional drill and blast methodology. The intake shaft and structure were constructed inside of a sheet pile cofferdam surrounded by a maximum of 20.1 m (66 ft) of water. The shaft was excavated 4.87 m(16 ft) diameter to a depth of 12.8 m (42 ft) below the tremie slab elevation. Steel lining, including a transition from 3.66 m to 2.74 m (12 to 9 ft) diameter and a90 degree elbow were installed in the inlet shaft and then backfilled with concrete. This paper will describe the RFP phase, the design phase, challenges of the underground construction and contractual challenges.

Jan 1, 2005

By W Taylor, S Chen, R Haywood, M White, R West, J Ranasinghe

In March 2012 a combined BHP Billiton and Hatch team embarked on a program to improve the concentrate burner efficiency of BHP Billiton’s Olympic Dam copper flash smelting furnace. A multi-faceted approach including an analysis of the furnace using operational knowledge and first principles engineering led to the design and supply of a new central-lance (disperser). A new, patented, swirl method of introducing the copper concentrate into the furnace was developed to integrate with the existing concentrate burner. Plant trials in 2014 demonstrated an increase of nearly 10 percent in the oxygen efficiency of the furnace. The improved efficiency is expected to provide savings in operating costs and asset life extension of downstream gas and dust handling equipment.CITATION:White, M, Haywood, R, Taylor, W, Chen, S, Ranasinghe, J and West, R, 2015. Improved copper flash smelting at Olympic Dam, in Proceedings MetPlant 2015, pp 382–395 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Rolf Schillinger

Blasting activities on the surface or underground necessarily involve the most sensitive aspect of environment remediation, human response or annoyance. Such effects are unavoidably characteristic of those activities. For this reason, blasting activities are governed by law and official regulations under surveillance of authorities, where companies and explosives engineers have to proceed within proper limits. Subject of the paper is a practical way of handling some necessary vibration standards being focused on blasting activities. The paper is based on the German Standard DIN 4150, Part 1 - 3, “Vibration in buildings”, Part 1: “Prediction of vibration parameters”, June 2001, Part 2: “Effects on persons in buildings”, June 1999 and Part 3: “Effects on structures”, February 1999.

Jan 1, 2006

By George Piscsalko

There are numerous methods currently available to assess the integrity of drilled shaft and ACIP piles. Each method has its advantages and limitations. This paper will compare the various available methods as well as introduce a new method for assessing integrity of drilled shafts and ACIP piles. This new method, known as Thermal Integrity Profiling, determines the integrity of the shaft both inside and outside the reinforcing cage by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements can be made by either passing a thermal probe through a standard Cross Hole access tube, or from embedding thermal wires within the shaft. This Thermal Integrity Profile method will be described in detail and one case history will be presented. Additional testing methods which will be compared include low strain Pile Integrity Testing and Cross Hole Sonic Logging. Advantages and limitations for each method will be discussed.

Jan 1, 2011

The most complete mining show ever held in the United States and the largest exposition of its kind to be held anywhere in the world in 1988. That's how the American Mining Congress is billing its "MINExpo International '88," to be held April 24-28 at Chicago's McCormick Place, the largest exposition facility in the country. MINExpo International '88 will combine for the first time two previously separate AMC-sponsored shows - the International Coal Show and the International Mining Show. Starting with the 1988 show, MINExpo International will be held every four years. The next show, in 1992, will be held in Las Vegas. The MINExpo in Chicago will feature more than 500 mining equipment and services exhibits covering 3 hm2 (320,000 sq ft) of exhibit space. Exhibitors will display products ranging from small safety devices to large earth-moving equipment. MINExpo is one of the few trade shows selected by the US Department of Commerce for its Foreign Buyer Program. Commerce is working with US embassies around the world to publicize MINExpo and to form delegations of visitors from many countries. Overseas visitors to the show will be assisted at an on-site International Business Center. It will provide currency exchange, translation, and other services to foreign buyers. Registrants at MINExpo will also be able to attend their choice of 27 morning-only program sessions. At these sessions, international mining experts from industry, government, and academe will analyze technical, strategic, and policy matters and discuss the outlook for the industry. "Toward the 21st Century" is the theme of this year's program. The technical workshops and managerial seminars are designed to assist mining executives, engineers, and geologists as well as mine superintendents, managers, and foremen in handling their responsibilities. Based on previous attendance at AMC international mining shows, the association says that more than 25,000 persons are expected to attend the Chicago show. It is expected that approximately 15% of the attendees will be from foreign countries. The Soviet Union will be among those exhibiting at MINExpo. The Russians have leased more than 2.8 dame (3000 sq ft) of space to display their mining machinery and equipment. It is the first time that the Russians have joined in an exhibition of mining equipment in the US. The two largest manufacturers of mining equipment in the Soviet Union, Setmash and Avtoexport, will put on display in Chicago a variety of Russian-made equipment. It will range from 100 t (110 st) heavy-duty dump trucks and diesel engines to drilling, hoisting, and conveying equipment. In addition to some 400 US exhibitors of mining equipment and services at MINExpo, nearly 100 companies will be present from other major mining nations such as Australia, Canada, Great Britain, Japan, the Netherlands, and West Germany. And, for the first time, a Chinese manufacturer will take part in the AMC show, participating with its US marketing partner.

Jan 3, 1988

By Both R. A, Daily B

The Patawarta Diapir, located in the northern Flinders Ranges (South Australia), has intruded into late Proterozoic Wilpena Group sedimentary rocks. The diapir contains disrupted blocks of a wide variety of rock types, most of which can be correlated with the Lower Callanna Beds of Willouran age, in a matrix of predominantly carbonate and siltstone breccia. Mafic rocks in the diapir appear to predate intrusion of the diapir. As with many other diapirs in the Flinders Ranges, copper mineralization is present in the diapir and occurs as narrow veins consisting essentially of carbonate with chalcopyrite and pyrite that formed after diapiric intrusion.Fluid inclusion studies demonstrate that the mineralizing fluid was a Na-Ca-K-Cl brine; probably derived by expulsion of interstitial water following emplacement of the diapir, with dissolution of evaporites within the Callanna Beds sediments and enrichment in copper by reaction with these sediments and associated basic igneous rocks. Mineral assemblages combined with fluid inclusion and geochemical data indicate a possible environment of vein formation of T ÿ 165°C, pH ÿ 4.3 ± 0.9 and log fO2 ÿ -47.3 ± 0.5. Sulphur isotope analyses indicate d34Sfluid ÿ 10 per mil, suggesting evaporites in the Proterozoic sediments as the major source of the sulphur but with some additional sulphur from an igneous source, possibly leached from the malic rocks of the diapir.

Jan 1, 1986

By Kazunori Matsushita, Frank Vespi, Emi Walder, Mitsuo Nozu

During the runway expansion project at the Fort Lauderdale-Hollywood International Airport in Florida (FLL project), therewere complicated geotechnical issues with a number of cavities in the limestone-loose sand mixed ground thatexisted in many areas below the existing ground. Collapsing the cavities and compacting the runway foundation to secure the take-off and landing of aircrafts was a necessary requirement for the project. The Mammoth Vibro-Tamper (MVT) which produces less vibration and noise level, was proposed and accepted as the alternative to the originally specified Deep Dynamic Compaction (DDC) for the runway with its length of 1.5 miles and area of 570,000 square yards. In this report, the shallow compaction effect and reduced ground vibration with the MVT are presented in comparison with the DDC which was utilized on the same project in a different area of the airport. INTRODUCTION MVT was developed by Fudo Tetra Corporation in the 1960’s and has been widely used in Japan (more than 14,400,000 square yards). For example, at the Kansai International airport, a large area including aprons was compacted with the MVT. It is capable of compacting up to approximately 5m in depth by using a heavy steel plate (3m x 3m) and a strong vibrator motor (V-180, 10Hz) on top of the steel thick plate with specified time duration. We were involved in densification work with the MVT at the Fort Lauderdale Airport Project (Figure 1) from June, 2012 to February, 2014. Deep Dynamic Compaction (DDC) was originally specified as the compaction method to secure the relative density over 70% in every 2,000 square yards grids, however, we proposed the application of MVT to reduce the vibration risk and it was accepted as the alternative (Figure 2). The compaction work was completed in February 2014, without causing any delay in regard to the residual settlement due to the high embankment (H=60ft=18m).

Jan 1, 2018

By Felipe Calizaya

This study describes the principles involved in the design of a booster fan installation, the basic requirements, and the provisions needed to guarantee a safe operation of the unit. It also describes how a booster fan should be selected and what measures should be taken so that events such as uncontrolled recirculation of air in a mine can be avoided. A computer program called MFSELECT is presented to assist the ventilation engineer in the design process a For a given mine ventilation network, the program determines the duties of fans and regulators that will fulfill the airflow requirements of a mine and minimize the total power consumption. The application of the program is illustrated by the detailed solution of a sample problem. A Case Study based on the Jim Walter Resources' No. 7 Mine is utilized to describe the basic requirements for the design and operation of booster fans, and illustrate their potential benefits in mine ventilation. Finally, the study discusses a process control system designed to evaluate the safety conditions in the mine and report on the status of both surface fans and underground booster fans.

Jan 1, 1990

By Lloyd G. Fitzgerald

"The dangerous nature of explosives makes them a potential hazard wherever they are used, but they are likely to exercise their greatest harmfulness under conditions inherent in coal mining. The ease with which explosives can be detonated and the suddenness and violence with which they detonate require great care in their handling and use, if acci-dents are to be avoided. Campaigns have been waged by the manufacturers, the Federal Bureau of Mines, coal-mining companies, and other agencies to educate users of explosives in their dangers and in their proper use and care.Probably 95 percent of the explosives accidents can be attributed to poor judgment, carelessness, negligence, or chance taking. In many explosives accidents it is difficult to determine the cause definitely, as the evidence of the origin is destroyed by the blast and frequently those involved have been killed. Survivors of the accident often are of little help in determining the cause, as the accident occurs so suddenly they cannot tell what happened or prefer not to divulge the information they have because it may point to their own carelessness.A survey has indicated that about 10 percent of all fatalities in coal mines were caused by explosives accidents (excluding gas and dust explosions initiated by explosives). A list of explosives accidents by States, from 1925 to 1932, classified according to the severity of the accidents, indicated that Kentucky and Wyoming had the greatest number of fatalities resulting from explosives accidents. Records of the Bureau of Mines show that 14 coal-mine explosions occurred from January 1 to June 1, 1943. Explosives were involved in four of these explosions. Black powder caused two of the accidents and permissible explosives used in a nonpermissible manner the other two. These statistics are mentioned to show that explosives are still causing severe accidents.Elimination of the hazards associated with explosives begins on the surface. Storage magazines should have no opening, except for entrance and ventilation; ventilators should be screened effectively to prevent the admittance of sparks as well as to prevent unauthorized entrance. The interior should be kept clean and dry, and the floor should be of nonsparking material with no metal exposed. The surrounding area should be kept free of combustible material for not less than 25 feet (and preferably 50 feet) in all directions. Storage magazines should be fire-resistant and reasonably bulletproof."

Aug 1, 1944

Rock mass classification is widely used throughout the underground mining industry—in both coal and hard-rock mines. It is used in all stages of the mining process, from site characterization to production operations. The goal of the International Workshop on Rock Mass Classification in Underground Mining was to provide a forum for leading practitioners of rock mass classification to come together and share their methods and experiences with the technique. The workshop was held in Vancouver, British Columbia, Canada, on May 31, 2007. It was co-chaired by Christopher Mark, Ph.D., P.E., National Institute for Occupational Safety and Health, Pittsburgh, PA, and Rimas Pakalnis, P.Eng., University of British Columbia, Vancouver, Canada. The proceedings of the workshop contain 16 invited papers from 9 countries, reflecting the international depth and breadth of current practice. Applications in both hard-rock and coal mining are well represented. Some of the topics that were addressed at the workshop include: • Major rock mass classification systems used in mining and their variants • Collection of input data through observation, rock testing, and geophysics • Design of mine layouts and rock support systems using classification • Estimation of rock mass strength and other input parameters for numerical models from classification • Applications in weak rock, raise boring, cavability assessment, and other special topics • Risk assessment using rock mass classification

Jan 5, 2007

By H. R. Cooper

Beginning from the point of view that process control of ore flotation can be approached by on-line analysis of processing behavior, an equation was developed which has characteristics useful for a multi-variable feedback loop. The application of this equation to optimizing control with a data acquisition system will be discussed in Part 11. OBJECTIVE OF CONTROL The purpose of developing a feedback method for concentrator control is to provide a means for determining ore processing behavior in order that data describing the ore can be used to make appropriate changes in control conditions while the ore continues to flow through the flotation circuit. In absence of simple linear relationships between pairs of variables in the flotation process, attention is directed to the need for a generalized relationship which possibly would incorporate all pertinent variables. It would be possible to apply such an equation to the control of variables in a concentrator in real time according to operational requirements as ore gradually changes in quality and processing behavior. To meet this objective, it is necessary to define relationships describing flotation performance in terms of performance variables capable of being measured on-line, either with on-line instruments and analyzers or with manual methods lending themselves to quick determination of meaningful information. Relationships derived to meet this objective form a model for the flotation process. The evaluation of flotation parameters of the ore and the execution of control on the basis of the derived information while the ore is continuing through the process would constitute a feedback control system. Data for the following control and performance variables can be made available: 1) ore feed rate, 2) collector addition rate, 3) lime addition rate, 4) pulp density, 5) assay or multiple assays in feed, tails, or concentrate sufficient for material balancing, 6) particle size distribution in flotation feed, 7) froth height, and 8) frother addition rate. Other process variables, such as flotation air input and mechanical agitation intensity, are usually not considered as control variables and were not taken into account in this analysis. Other data, such as that describing the ore, would be useful for concentrator process control. However, information of this type (such as ore hardness, grain size of the mineral, chemical species of the mineral, and ore surface properties) being not presently measurable in the on-line sense, has the effect of causing disturbances in the system which can be detected only indirectly. The process control system being sought must recognize disturbances by their effect on measured performance followed by determining control changes to compensate for them in meeting the objectives of improved performance (perhaps higher throughput, maximum return, etc.). A suitable model for the process having capability of recognizing the effects of ore disturbances should provide the means for introducing proper compensation through control changes. This would be done by processing on-line data with the model to calculate coefficients reflecting ore characteristics. This procedure can only be applied in a typical flotation system when on-line data can be processed at faster rates than the usual rate at which the ore in flotation feed takes on significantly different characteristics. For example, material balance data can be accumulated in approximately 5-min intervals using on-line X-ray fluorescence analysis. The flotation system time constant might be 15 min including grinding. Ore changes having time constants longer than 1 hr could be accommodated using on-line feedback control by this procedure. FORM OF A FLOTATION MODEL A suitable form for mathematical expression of the flotation process is an equation involving rates, when each of the components entering into the separation can be treated independently by a rate equation. A first-order, kinetic rate equation can be written on

Jan 1, 1967

By P G. Gaylard

The minerals Industry carries out over US$ 2 billion of R&D annually. The R&D is performed at three levels ? in house research facilities; on a one-on-one basis with a research provider; as syndicated (collaborative) research. The key to a successful R&D programme is project selection. It is suggested that at this time of ?bounty? for the minerals industry the research portfolio should contain some ?blue sky? but potentially long term significantly beneficial projects. This said, the projects should align the technical concepts with the business imperatives. AMIRA has found the ?Road Map? concept has assisted in defining areas for R&D. Examples of this methodology using a Copper Road Map developed by AMIRA for the copper producers operating in South America is presented. The benefits derived from syndicated research are also discussed.

Jan 1, 2007

By R S. Hamilton, S R. Grobler, M E. Greenway

The progressive development of underground mines frequently requires increased ventilation flow rates through mine shafts that were originally designed for lower rates. Where these shafts are equipped with conveyances running on rope guides, the higher air flow rates adversely affect the lateral motion of conveyances and could cause conveyances to collide with the shaft walls or with one another. Hence the safety impact of higher flow rates requires proper assessment. This can be undertaken by use of computer simulation models to predict the dynamic motion of the conveyances during hoisting. It can also be undertaken entirely by field testing, or using a combination of simulation and field testing. This paper discusses these techniques and makes cautionary remarks about setting an absolute generic maximum flow velocity for all shafts. Approaches to assess existing shafts for increased ventilation flow rates are also discussed.CITATION:Greenway, M E, Grobler, S R and Hamilton, R S, 2017. Safety impact of increased shaft ventilation on rope guided conveyances, in Proceedings Australian Mine Vent Conference 2017, pp 261–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017