Search Documents

By William J. Neely

Augercast piles are formed by drilling a continuous-flight auger into the ground and, on reaching the required depth, sand-cement grout or concrete is pumped down the hollow stem as the auger is withdrawn. The sides of the hole are supported at all times by the soil-filled auger, eliminating the need for temporary casing or bentonite slurry. The augercast piling method is fast and economical; there is no vibration, very little noise and, if executed properly, no ground displacements during installation. The method is well suited to sands which are easy to drill and are readily transported up the auger. Relatively little attention has been given to augercast piles in the literature which might be part of the reason for the considerable variations in local practice, building code requirements and design methods. The purpose of this paper is to discuss some of the features of augercast pile installation that are known to influence both the structural and geotechnical capacity of the pile, to evaluate several empirical design methods and to look at some important aspects of quality control of augercast pile installation.

Jan 1, 1990

By Maxwell Gensamer

Jan 1, 1960

By Raymond W. Henn

The 31th annual short course ?Grouting Fundamentals and Current Practice? was held at the Colorado School of Mines, in Golden, CO June 7-11, 2010. The field demonstration portion of the course was conducted June 10 at wlh Construction Co.?s yard in Denver, CO. The full-scale field demonstration presents many types of drilling and grouting equipment in operation as well as numerous grouting methods performed under various field conditions.

Jan 1, 2010

By Dunlop GA

Pilot Plant confirmatory testing of the treatment route developed in the Metallurgical Laboratory is an essential factor in the development of complex ore bodies. Objectives should be well defined to permit the efficient planning and cost effective operation of the pilot plant project. The primary objective for the pilot plant should be to confirm the viability of the developed flowsheet on a continuous basis, examining only major variables such as ore types, quantum changes in grind, comparison between bulk and sequential flotation circuits, use of flotation columns, evaluation of autogenous grinding and production of samples of concentrates for market evaluation. Secondary objectives may include the collection of engineering design data and the production of a comprehensive report to Bankable Document standards to provide technical support for capital financing. The complexity of the ore body and the scale of the final operating project together with the pilot plant objectives will determine the extent of the pilot plant operations. The level of expenditure associated with a pilot plant can vary, in total cost and as a percentage of the total development capital investment required to take the prospect from exploration to a producing mine. Factors contributing to expenditure are discussed. Associated with cost considerations is the level of confidence mining company investors can have that their capital investment will return dividends.

Jan 1, 1990

By Christopher Mark

Knowledge of in situ stresses is fundamental to many studies in earth sciences, and coal mine ground control is no exception. During the past 20 years, it has become clear that horizontal stress is a critical factor affecting roof stability in underground coal mines. The theory of plate tectonics and the World Stress Map (WSM) project has been extremely helpful in explaining the sources and the orientations of the horizontal stresses observed underground. Recently, WSM geophysicists studying deep-seated stresses have developed a model of how stress magnitudes vary with depth in the crust. They have devoted relatively little attention to near-surface stresses, however. This paper explores the relationships between deep-seated and shallow in situ stresses in several of the world?s coalfields, using a data base of more than 350 stress measurements from underground coal mines. The analysis indicates that distinct regional trends exist, corresponding roughly to the regional stress fields identified by the WSM. The paper presents equations for estimating stress magnitudes that were developed by treating depth and elastic modulus as independent variables in regression analysis. The magnitude of the horizontal stress increases with depth, at rates that range from 0.8 to 2.0 times the vertical stress, just as the WSM ?critically stressed crust? model predicts. Overall, it seems that the stress regimes encountered in underground coal mines are closely linked to those that exist deep in the earth?s crust.

Jan 1, 2008

Variations in product distribution in the carbon-sulphur dioxide system due to variations in reaction temperature, sulphur dioxide concentration in the feed gas, and gassolid contact time were studied in detail for a brown coal char. The results were compared with those for two wood chars, a coke prepared from Liddell coal and two cokes prepared from Ac1and coal. Conditions were chosen such that gas-solid diffusion rates did not hinder chemical attack of the carbon.With brown coal char under suitable conditions, the selectivity of sulphur in the sulphur dioxide fed, to either elemental sulphur or carbon disulphide, was in excess of 90 per cent. The wood chars gave very similar product distributions Ito brown coal char. However, the cokes from Ac1and and Liddell coals were respectively approximately three and seven times less reactive than the brown coal char.The approximate carbon holdup required to just achieve total conversion of sulphur dioxide, and thereby achieve high selectivity to elemental sulphur, is given as a function of reaction temperature.

Jan 1, 1974

By Alicia Esther Ares

The family of Zn-Al (ZA), Zn-Ag and Zn-Al-Ag (ZINAG) alloys offers high mechanical properties, ease of finishing, the advantage of low energy and pollution-free melting. Also, present alternatives to the well developed alloy systems, such as brasses, bronzes, cast irons and aluminum alloys. The main objective of this paper is to measure thermal parameters in ZA, Zn-Ag and ZINAG hypoeutectic and hypereutectic alloys directionally solidified which present columnar, equiaxed and columnar to equiaxed transition structures (CET). Also, estimate the mechanical properties, such as microhardness and tensile parameters and correlate these with the thermal (cooling rate) and structural parameters (grain size and dendritic spacing). The different types of structures were analyzed with optical and scanning electron microscopy. The results showed the influence of concentration, microstructural arrangement and thermal conditions during solidification on the mechanical properties. The results of the present investigation are compared with previous experiments.

Jan 1, 2010

By L Lachance, F Flament, D Leroux, S GariTpy

"Considerable metal values are often locked in stockpiles (ore, concentrates, heap leach pads, slags, reverts, etc.) and process equipment (bins, holding tanks, thickeners, etc.). This is more than enough to justify accurate accounting of such in-process metal inventories from both financial accounting and operational perspective. However, accurately determining the metal inventory of an in-process unit is often a challenge in industrial practice. Audits have shown that available indirect or direct measurements often carry large inaccuracies. Sooner or later, ignoring these measurement errors lead to unexpected incoherencies in reported metal balances. In such situations, coherent metal balances are then achieved through subjective and sometimes significant adjustments of in-process inventory levels. While such metal accounting methods applied by mineral processing engineers used to be rarely challenged, they are now being increasingly scrutinised by various stakeholders. Hence, metal accounting procedures that mitigate subjectivity in adjustments while still coping with the unavoidable uncertainty are more relevant than ever.This paper reviews three different metal accounting methods for reporting in-process metal inventory values. Their individual application strongly depends on the available measurements i.e. The indirect method where the metal inventory of a given process unit is determined by subtracting the cumulative reclaim from the cumulative feed carries important flaws. The direct method also comes with challenging accuracy issues so that emptying a process unit is often the best available inventory measurement. This reality is recognised for by further analysing a previously proposed operating mode where two interchangeable process units are alternately used. The third investigated method is the redundant method which combines indirect and direct methods for a given process unit. This paper reveals that the dual process unit operating mode and the redundant method can both significantly improve the estimation quality of in-process metal inventories.CITATION:Lachance, L, GariTpy, S, Leroux, D and Flament, F, 2013. Review of metal accounting methods for in-process metal inventories, in Proceedings MetPlant 2013, pp 102-117 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By Omid Lashkari

Keywords: SEED, SSM materials, Microstructural evolution, Rheology, Swirling Speed SEED (Swirled Enthalpy Equilibration Device) is established itself as a new technology amongst the many Semi-Solid Metal (SSM) processes, where swirling of the mush plays an important role in modifying the dendritic structure of as-cast parts. A range of semi solid metal structures, dendritic, rosette and/or globular morphology of primary phase, can be prepared using SEED. The current article reports on the application of rheological tests in characterizing microstructural evolution during SSM processing of 356 Al-Si foundry alloy. A simple parallel plate test machine, designed and constructed at our labs, was used to determine viscosity values for each structure and identify the optimum structure with superior die filling characteristics. Such findings have important technological and economical implications during high pressure die casting of semi- solid metals. The strain-time graphs for 356 Al-Si foundry alloy indicated lower viscosity values for globular microstructure, i.e. improved die filling.

Jan 1, 2005

The granulites and related "dry" igneous rocks tend to be passed over during exploration for metals. Preliminary data show that high trace concentrations of eu, Ni, and other metals of economic interest are commonin orthopyroxene and some of the other granulite minerals. During retrograde metamorphism of granulites, pyroxenes are converted to amphiboles or phyllosilicates, and significant quantities of metals are released andbecome available for incorporation into new mineral phases, or may be transported elsewhere. S-rich scapolite is the normal scapolite of granulites. Its retrogression to secondary plagioclase provides much S which scavengesCu and Ni, from pyroxenes undergoing retrogression, thus producing ore-fluids. A full analysis of a scapolite with 5·10 per cent SOg is given.Beryl is unstable in granulites but the rare Be mineral taaffeite (Al4Mg(Be, FeII)Os) with 5·50 per cent BeO occurs in central Australia as a pale green tabular mineral easily confused for chloritoid in hand-specimen.Metamorphic differentiation and mobilization of primary ore concentrations are major factors controlling their post-granulite attitude and grade.Zones of retrograde metamorphism are commonly found cutting or engirdling granulite terranes. As the "volatiles" for the new hydrous minerals of many of these zones are of deep-seated origin and may be juvenile, sulphide mineralization in them may also be of mantle origin. However, it is likely that much of the metal content could be scavenged from the granulites as they are down-graded by juvenile volatiles. Major Bouguer gravity anomalies delineate some granulite terranes (e.g. Fraser Block, Western Australia), and are related to deep-seated geosutures and mantle disturbances.Many granulite terranes are linear belts and appear to be welded to older cratonic blocks.

Jan 1, 1969

By F. Charette

The paper reviews recent investigations of the impact of corrosion on the performance of both plain and coated Swellex rock bolts. It addresses the problems associated with estimating and predicting corrosion rates of friction bolts, and based on field data it suggests an empirical relationship to predict corrosion rates. A review of the necessary qualities for a protective coating leads to recent experience with coated Swellex bolts that suggest that they can contribute to extending the useful life of Swellex bolts in potentially corrosive environments.

May 1, 2004

By Peter Swanson

A seismic monitoring network has been installed in western Colorado (USA) in the vicinity of three underground coal mines to (i) distinguish and characterize seismic activity as either mining related or naturally occurring, (ii) implement a real-time event monitoring and notification tool, and (iii) collect data for use in research studies aimed at quantifying impacts from mining-related and natural seismicity. These potential impacts include dynamic rock mass failures such as coal bumps as well as strong shaking in the vicinity of critical structures such as impoundment dams, reservoirs, mine seals, mine openings, and steep slopes. Examples of two damaging seismic events are presented and the mining and geologic factors attending these dynamic failures are described.

Jan 1, 2008

By Steve Kral

Commodity price down cycles are a fact of life in the mining industry. And companies pre-pare for them as best they can. Evenso, operations are still curtailed or closed during those cycles, profits shrink, layoffs are inevitable and many companies do not survive. However, one of the few good things that occurs during down cycles is the new, innovative exploration, mining and processing technologies that come about during hard times. To survive the lean times, the mining industry turns to improved technology to decrease costs and hold the bottom line. And, because mining is a cyclical business, each down cycle brings about technology improvements that carry over into the good times.

Jan 1, 2004

Evaluation of Grinding Medium Wear in Stirred Mills The standard fine grinding machines in the minerals industry are stirred mills whose performance largely depends on the competency of the grinding medium. Medium wear in stirred mills is one of the key parameters for medium selection. A wear evaluation methodology is developed and applied in this paper to measure the wear rate of river sand using a laboratory batch stirred mill. The procedure is demonstrated by testing the sand medium in a 0.55 kW batch stirred media detritor (SMD). The sand wear rate determined in the laboratory batch mill is successfully scaled up to that determined on a full-scale Metso 355 kW SMD mill.

Sep 13, 2010

To gather additional field data from the western United States, researchers from the National Institute for Occupational Safety and Health (NIOSH) installed an array of field instrumentation at a longwall coal mine in Central Utah. The purpose of this field site was to monitor ground movement and changes in pressure during mining where conditions include massive, stiff overburden and relatively deep cover. To accomplish this, field instrumentation was installed in the two-entry gate road between the fifth and sixth longwall panel in the current mining district.

Jan 7, 2020

By Misra V. N

Davis tube tests were conducted on a Koolanooka magnetite iron ore sample, supplied by Kingstream Steel Ltd, to determine the optimum grind size, maximum iron recovery and the cleanness of the products from low intensity magnetic separation (LIMS). The ore sample contained 38.6 per cent iron, 37.8 per cent silica, 6.5 per cent magnesia and 0.54 per cent alumina. XRD and microscopic examination showed that the main minerals in the ore were amphibole (42 per cent), magnetite (39 per cent), and quartz (14 per cent). Amphibole, (Mg, Ca, Fe),Si8O22.2(OH), containing 50.3 per cent SiO2, 35 per cent FeO and 11.5 per cent MgO is the main gangue mineral in the ore, and about 30 per cent of the total iron in the ore is contained in the amphibole. Heavy liquid separation tests showed that it is very difficult to separate iron from silica by gravity separation to obtain a high quality iron concentrate. Three grind sizes were initially tested, ie 45, 38 and 20 ¦m. It was found that grinding to 100 per cent -38 ¦m (P80 of 29 ¦m) appeared to be the best option for liberating the magnetite from gangue minerals. The iron recovery to the LIMS magnetic product for the 100 per cent -38 ¦m sample reached 73 per cent and the iron content was 65 per cent. Further test work suggested that the optimum grind size was a Psu of 25 ¦m.

Jan 1, 1999

By M. Karmis, S. K. Weisiger

The traditional method for training personnel in the mining and other heavy industries has been face-to-face, either via a lecturer in a classroom or through an apprenticeship. With the advent of applications tools such as video, computers, and the Internet, however, a much broader range of training delivery methods is available. Especially exciting are the broad capabilities of multimedia packages that combine the best features of numerous delivery methods. Applying multimedia environments in training holds great potential, especially when there is considerable difficulty in reconstructing real training environments. The authors discuss various delivery methods currently used in training employees, including perceived advantages and disadvantages of those methods. The authors then discuss and evaluate current computer-based training efforts of the mining industry and present an example of a multimedia training tool.

Jan 1, 2001

By A. C. Smith

Although only used in a few U.S. longwall mines, bleeder-less ventilation systems can be an effective spontaneous combustion control method in mines having a demonstrated history of spontaneous combustion. To provide insights for the optimization of bleederless ventilation systems for U.S. underground coal mines, a computational fluid dynamics (CFD) study was conducted to model the spontaneous heating in longwall gob areas using a bleederless ventilation system. A single longwall panel with a bleederless ventilation system was simulated, and typical longwall mine ventilation data were used in the simulations. The permeability and porosity profiles for the longwall gob were estimated using a geotechnical model and were used as inputs for the CFD modeling. The effects of gob permeability and resistance of the collapsed entries on the spontaneous heating were studied. The effectiveness of using nitrogen injection to prevent spontaneous heating in the gob was also examined.1

Jan 1, 2008

By G de Jong, W Sunyoto, K Sari, P Silalahi

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Big Gossan mine is operated by PT Freeport Indonesia and is one of the largest stope-and-fill mining systems in the world. The Big Gossan deposit is a ~200 m wide, 1200 m long and 500 m high steeply north-east-dipping to subvertical skarn body at the Cretaceous-Tertiary Ekmai-Waripi contact. The copper-gold mineralisation, with a 1.3 per cent copper equivalent cut-off grade, occurs mainly proximal to the Ekmai-Waripi contact in the garnet-clinopyroxene prograde skarn at the base of the Tertiary Waripi formation and partly distal to the contact in the tremolite-actinolite retrograde skarn of the Tertiary Waripi formation.The Big Gossan stope mine is designed from 2540 m to 3020 m above sea level. Present active stoping operations occur at level 2540 mL to level 2640 mL and are done in a primary and secondary stoping sequence. The width and length of the stopes is 15 m and 20 m respectively, while the height of the stope varies between 20 m and 40 m, depending on the ground conditions. The stability of the stopes is visualised in the Mathew’s Stope Stability graphs. These graphs and actual Cavity Measurement Scanner measurements on the stope will predict and show the overbreak and underbreak, which affect the reconciliation of the mined stope and also the pillar stability between the primary stopes. Geological factors like major structures, joints, veins and alteration intensity are important factors that correlated with the stability of the Big Gossan stopes.CITATION:Sari, K, de Jong, G, Silalahi, P and Sunyoto, W, 2015. Stope stability at the Big Gossan skarn deposit, Papua, Indonesia, in Proceedings PACRIM 2015 Congress, pp 139–146 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Sutham Niyomwas

The Fe-TiC composite powder was synthesized in situ by carbothermal reduction of ilmenite. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The effects of the reaction temperature (1300 °C - 1500°C) and milling time of precursors on the Fe-TiC conversion and powder morphologies were investigated using XRD and SEM method. The synthesized products showed that composite with iron matrix and titanium carbide as a reinforced phase was formed.

Jan 1, 2006