Search Documents

By Robert P. Kennedy, Andrew H. Merritt, Edward J. Cording, Thomas R. Kipp

INTRODUCTION Measurement of certain data associated with nuclear testing necessitates the reception of waves at the instrument location which are unaffected by reflection off internal structures or tunnel surfaces. Therefore, in order to provide necessary facilities for the fielding of experiments in support of the underground nuclear testing program, the Defense Nuclear Agency (DNA) commissioned a cost and feasibility evaluation pertaining to the design and construction of large underground cavities in Rainier Mesa. The effort included research into past experience pertaining to the excavation and support of large underground caverns, assessment of the geological conditions which exist in Rainier Mesa, preliminary design of the chambers and their rock support systems based upon the geological setting, development of mining plans for the excavation of the caverns, and estimation of the cost and manpower schedule to complete construction. This paper summarizes the results of the feasibility evaluation. The investigation was limited to modified hemispherical configurations ranging in size from 24.4 to 91.4 m (80 to 300 ft) in diameter. Two cavity support systems were considered. The first employs internally installed rockbolts as the means of primary rock support while the second involves the use of annular tendon galleries located above the chambers from which primary support members are introduced prior to general excavation. The internal support configuration was considered for cavities with spans of 24.4, 36.6, 48.8, and 54.9 m (80, 120, 160, and 180 ft) while the external support configuration was considered for cavities with spans of 54.9, 73.2, and 91.4 m (180, 240 and 300 ft).

Jan 1, 1979

By G. Krogman, C. Walla, B. Wood

The Gebo Mining District (District) is located in the Bighorn Basin of Wyoming. Commercial underground coal mining began in 1906 with the arrival of the railroad in Thermopolis, which is located approximately 11 miles to the south. Mining in the District ceased by the early 1970’s. In Fall of 1999, Lidstone and Associates, Inc. (LA) and their subcontractors were retained by the Wyoming Abandoned Mine Land Division (WyAML) to perform an inventory of over 500 abandoned mine sites across Wyoming. During the summer of 2000 field inventory, a 30-foot deep headcut (Figure 1) and sink-hole were noted in the West Fork of Sand Draw (WFSD), immediately west of the Town of Gebo. The headcut and sink-hole were located at the culvert outfall associated with a stream crossing of a relatively well traveled county road. Upon further investigation, it appeared that underground mine workings had been exposed at this location. This resulted in a condition whereby water would be conveyed directly into the mine workings during a runoff event. The exposed mine workings as well as stream capture created a very hazardous condition. The WyAML implemented mitigation measures in the summer of 2000 by constructing a temporary stream crossing upstream of the existing failed crossing. To address this hazardous situation as well as a number of other hazards identified in the District during the field inventory, the WyAML retained PHC Reclamation, Inc. (PHC). PHC was directed to perform a field investigation and develop a Reclamation Plan to address all existing abandoned mine hazards in the District. Federal, state, and private parties own lands within the District. Hazards identified during the investigation included an underground mine fire, open adits, open shafts, subsidence, drainage problems, and coal slack. A Report of Investigation (ROI) was submitted to various regulatory agencies that documented the existing conditions and conceptual reclamation plans to remediate the hazardous conditions. After review of the ROI by the US Department of Interior - Bureau of Land Management (BLM) an on-site meeting was conducted. BLM Cultural Resource personnel declined to approve a District reclamation project until a historical overview of the entire District was prepared. Due to the hazardous situation associated with the WFSD stream crossing, Hot Springs County Road and Bridge Department convinced various state and federal regulatory agencies to allow reclamation of the stream crossing to occur. A decision was made to allow reclamation on privately owned lands within the WFSD drainage. This decision limited the amount of channel that could be subjected to reclamation upstream of the crossing to privately owned lands. PHC contracted LA to perform a geologic, geomorphic, hydrologic, and hydraulic investigation of the drainage to assist in the development of a WFSD reclamation plan. LA’s investigation consisted of four parts: Delineate the extent of mine workings in the area; Identify all drainage structures that required mitigation; Survey a series of channel cross-sections and a longitudinal profile of the impacted channel; and, Develop basin hydrology to assist in the design of a stable reclaimed stream channel.

Jan 1, 2006

The annual reports of the supervising engineers of the nine sections comprising the Mining Division are assembled here and constitute the annual report of the division. In planning activities the aim is to adapt them to changes in conditions, in the needs of the mining industries, and in the public interest: those that contribute most to solving the present problems are emphasized, investigations of less immediate importance being recessed if necessary.

Jan 1, 1941

By Sven Reutzel

Investigations show that Co-based melts embedded by glass flux in a crucible can be under- cooled nearly as strong as samples processed containerlessly by electromagnetic levitation. This allows to measure magnetic susceptibility on undercooled melts while combining the use of a Faraday-balance and undercooling technique. The magnetic susceptibility of Co and Co-based alloys (such as Co-Pd and Co-Cu) is investigated as a function of temperature from superheated to undercooled state. This is done by measuring the change of magnetic force F, on a sample in a constant magnetic field Bo and an additional gradient field by means of a Faraday-balance. When liquid Co-based alloys are undercooled the magnetisation steeply rises if temperature approaches the Curie temperature. The magnetisation is measured for some Co-based alloys in liquid state as a function of alloy system and its concentration. The results show that the magnetic susceptibility of the liquid undercooled samples follows a Curie-Weiss behaviour, from which Curie temperature and magnetic moments for the liquid state are inferred.

Jan 1, 2002

By Chas. F. Jackson

The annual reports of the supervising engineers of the nine sections comprising the Mining Division are assembled here and constitute the annual report of the division. In planning activities the aim is to adapt them to changes in conditions, in the needs of the mining industries, and in the public interest; those that contribute most to solving the present problems are emphasized, investigations of less immediate importance being recessed if necessary. The strategic minerals investigations of the bureau afford an example of this change in emphasis to problems of immediate and urgent interest, and during 1941 they comprised, upon the basis of appropriations and expenditures, more than 90 percent of the work of the division.

Jan 1, 1941

By Fabio do Prado Verderano

A partir de corpos de prova de uma chapa de aço baixa liga NBR 6656 grau LNE 26, realizou-se a caracterização microestrutural, levantamento do perfil de dureza ao longo da espessura da chapa, ensaios de tração monotônicos, cíclicos de fadiga e análises fractográficas. Concluiu-se que, nas extremidades da espessura da amostra, o valor da dureza é maior, indicando que quando a chapa foi laminada as superfícies em contato com os rolos de laminação sofreram encruamento, aumentando a dureza nessa região. A microestrutura encontrada e o grau das inclusões presentes na amostra são compatíveis para o material, bem como as propriedades mecânicas monotônicas, que estão de acordo com a especificação. Por meio de ensaios de fadiga de baixo ciclo, encontrou-se uma boa correlação entre as propriedades monotônicas e cíclicas do material para a proposição da equação de Basquin, considerando-se dados seguros, quando utilizado os primeiros vinte ciclos do ensaio de fadiga para estabilização de cada corpo de prova. Verificando-se a seção transversal da fratura do corpo de prova, observa-se que o mecanismo de falha do material ocorreu a partir do aparecimento de trincas na interface ferrita-cementita com propagação transgranular até a fratura final.

Aug 17, 2017

By D. E. Andrews

The objective of this study was to investigate the environmental effects of slaking of surface mine spoils. To accomplish this, both field and laboratory programs were undertaken, supplemented by a thorough literature search. The field program consisted of drilling the highwall as well as test pitting in recent, two-, five, and ten- year-old spoil piles at four active mining sites in the eastern bituminous coal fields. Pertinent observations were made and samples collected for laboratory analyses which consisted of several standard geotechnical, agronomic, and geochemical tests. Durability tests utilized included jar slake, cyclic wet-dry, rate of slake, and slake durability tests. Correlation between field and laboratory portions was made- and results presented. The report is concluded with a discussion of the slaking process and associated environmental impacts, proposal of a preliminary classification system for use in premine planning, and presentation of management techniques to optimize the slaking process.

Jan 1, 1980

By A. Schaum

On average, there are approximately 10 fatal haul truck accidents per year. The most common causes for haul truck accidents include mechanical problems, inadequate training and insufficient road/berm maintenance. Due to the frequency and magnitude of haul truck accidents, new training methods are being investigated. With the widespread availability of computers and new technology becoming more reasonably priced, the ability to incorporate computer-based training for miners is becoming more possible. It has been shown that computer-based training is just as effective in knowledge acquisition as traditional lectures, and computer-based training can lead to a significant increase in the retention of material (Williams and Zahed, 1996). Studies have also shown that more engaging training methods lead to more effective knowledge acquisition (Burke et al., 2006). A supplemental system for current and new miner training to address the common causes of fatal accidents was developed. The training system is a virtual preshift inspection of a haul truck, and it can train new haul truck operators to identify parts that look defective. The training will increase an operator?s ability to recognize problematic parts and correctly identify the corrective action needed. Increasing the quality of training by providing an engaging, simulated hands-on environment will lead to safer behaviors by trainees, which will ultimately lead to fewer accidents and fatalities.

Jan 1, 2008

By R. I. C. Manning

The Old Dominion Co, at Globe, Ariz., like the: Phelps Dodge Corporation with which it is closely allied, considers safety a major operating problem. Safety is fostered by this company in consideration of both the humanitarian and economic aspects; the officials, take pride in promoting the welfare of employees, and the management has found that the safest way is the most eco¬nomical and that unless an organization is operated economically it can not continue to exist successfully. In planning and operating any safety, organization, terry things must be taken into consideration because an Enterprise can not be operated solely for safety any more than it can for any other single part of the operations. All work must be planned and executed for the common interest.

Jan 1, 1931

By Eric R. Borys, Amaneh E. Kenarsari, Brett Gitskin

This case study discusses impacts of excessive Earth Retention System (ERS) lateral movement at a project in city of Chicago. The ERS (cantilevered sheeting) moved inward towards the excavation and caused lateral displacement and cracks in six drilled shafts located about 1 to 2 lateral feet (0.3 to 0.6 m) from the face of the sheet pile wall. Up to 9 inches (23 cm) of horizontal movement was observed on top of the supporting sheet-pile. Similarly, survey measurements showed the top of the drilled shafts moved laterally up to 8 inches (20.3 cm). To evaluate the cause of failure and determine a remediation solution, the soil, shaft and site conditions were investigated. Pile Integrity Tests (PIT) were conducted at the affected drilled shafts. The shafts with identified anomalies were cored and video-recorded. The cause of the failure was determined to be related to variable soil conditions across the site, deeper excavation (i.e., increased effective ERS wall height), and other differences between design and as-built conditions. Internal bracing, in the form of walers and rakers, was installed to limit further movement of the sheet pile as a short-term solution, with additional grade beams framed into the basement slab-on-grade as a long- term solution. Five of the six cracked shafts were spliced with reinforcing bars and high strength grout and one shaft was replaced. INTRODUCTION The subsoil in the Chicago Area mostly consists of glacial till clays underlain by water-bearing granular soil over bedrock. The glacial clays have very soft to medium consistencies for a typical thickness of 30 to 50 feet (9.1 to 15.2 m) below which hard clays (Hardpan, i.e., heavily over-consolidated clay soils) are encountered. The soft clays are often referred to as the “Chicago Blue Clay”. Beach Sands are also found above upper soft clays in several areas, especially within a three-mile strip near Lake Michigan (Peck and Reed 1954). Due to the existence of soft clay in Chicago area, supporting the mid to high rise buildings on drilled shafts extended to Hardpan is a common practice in modern building design. In the early 19th century it used to take about 3 weeks to excavate 1 shaft hole and about 1½ days to fill the shaft with concrete in Chicago (Manierre 1916). The early 19th century methodology of excavating a shaft consisted of hand digging the shaft, installing wood lagging as temporary shoring with spoils removed with a rope and pulley system from the surface. Today, the excavation of a typical drilled shaft in Chicago uses heavy drilling equipment and requires much less time for excavation and concrete placement. It is not uncommon for contractors to excavate shafts and place concrete at a rate of about 2 to 5 drilled shafts per day (with one drill rig).

Jan 1, 2018

By Sidney Katell

This Bureau of Mines study estimates capital investment, operating costs, and selling prices for three underground bituminous mines producing coal with annual production ranging from 1.03 to 3.09 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of December 6, 1974, under the Bituminous Wage Agreement of 1974, and costs for material and equipment are based on 1975 indexes Initial capital investment ranges from $26,498,500 for the 1.03- million-ton-per-year (MM tpy) mine to $67,173,300 for the 3.09-MM-tpy mine. Total capital investment ranges from $37,437,500 to $92,984,300 for the same mines. Corresponding selling prices for the coal range from $14.83 to $13.26 per ton, assuming a 15-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1975

By Victor C. Bryan

"One of the more challenging issues facing operators of U.S. mines and quarries is blasting in an environmentally acceptable way. It is quite important that industry management understand and apply guidance, discipline, and control in the exercise of blasting operations. This presentation is a discussion of problems related to that environment away from the blasthole that may or may not be adversely affected by blasting and the steps management may consider in resolving resultant problems. In any case, one of the main concerns that will continuously be brought up is thatmanagement procedures inherent to good blasting is a uxporate responsibility of the mine or quarry business entity; and can not be delegated to the explosive manufacturer or supplier. This management attitude, based on education, training, and the comprehension that the process of production begins with drilling and blasting and consumes a significant amount of overall production costs."

Jan 1, 1995

CONTENTS RUSSIA-R. C.-BECKSTROM 3 VENEZUELA-F. H. KAY 9 TRINIDAD-W. J. MlLLARD 20 RUMANIA-1. I. GARDESCU 26

Jan 1, 1932

With the launch of Immersive Technologies' next generation of Advanced Equipment Simulators for the mining industry, correlating and influencing safety, productivity and maintenance with operator competency improvements is now made even more effective. In early 2008, Immersive assembled a project team to investigate the potential linkages between operator competency and performance. Advanced Equipment Simulator Users with a range of sophistication were interviewed and consulted. The result was new and enhanced 'value realisation' programs to directly assist mine sites to deliver the expected return on investment (ROI) from simulators and operator competency development. In just over one year, 29 mine sites around the world have benefited from 34 completed programs. Case studies have been compiled to demonstrate the impact of the implementation of this approach, including at the following operations: Anglo Coal - Callide (Australia), Freeport McMoRAN - Grasburg (Indonesia), Equinox Minerals - Lumwana (Zambia), Peabody Energy - Cabllo (USA), and Xstrata - Lomas Bayas (Chile). Significant performance improvements have been achieved including: reductions of 47 per cent in gear shifting and 37 per cent in over speed errors, improvements of 68 per cent in park break errors and 12 per cent in spotting time, and increase of 54 per cent in passing emergency fire handling competency tests. This presentation draws on these case studies to clearly demonstrate the linkage between improved operator competency through the implementation of training programs tailored around Advanced Equipment Simulators and production performace measured by a range of standard metrics at mines around the world.

May 1, 2010

By Peter F. Steidl

Seven degasification wells have been completed in the Pittsburgh coalbed at the new Emerald mine near Waynesburg, Pa. Funding was provided by the Bureau of Mines to perform stimulation treatments on five of the wells, to show that this is a feasible and economical means of degasifying part of a coalbed. The seven wells ranged in depth from 590 to 910 feet. Stimulation treatments used 25,260 to 42,660 gallons of foam and 7,400 to 12,800 pounds of 20/40-mesh prop sand. Pumping rates were 10.8 to 11.6 bbl/min and treating pressures were from 1,050 to 1,600 psig. On the day following stimulation, gas production ranged from a few hundred cubic feet per day to more than 100,000 cu ft/day.

Jan 1, 1978

By Howard A. Perko, M. Mae Benvenga, Heather H. Trantham

Displacement of soil and groundwater during helical pile installation can produce excess pore water pressures (PWP) in fine-grained soils. Pore water pressure reduces effective stress in the soil immediately adjacent to the helical pile shaft and near the helical piles. Previous studies have shown generation of PWP may affect the capacity to torque ratios of the helical bearing elements. Large diameter helical piles that generate much of their torque and capacity from shaft adhesion are affected by PWP and therefore exhibit significant pile "freeze" after installation. Computer modeling is used herein to evaluate PWP immediately adjacent to helical pile shafts during installation in various soil types. The models show the degree and distance from the shaft that is influenced by PWP during installation and the amount of time required for the PWP to dissipate. Pile freeze has been measured on several project sites by re‐torque measurements. These re-torque data are compared with computer modeling and correlations between saturated hydraulic conductivity and dissipation time are presented and discussed. INTRODUCTION Helical piles are full-displacement piles, meaning installation does not produce drill spoil. Soil is displaced laterally as the pile progresses into the ground. This displacement of soil causes an increase in PWP, which reduces adhesion between the pile and the soil. For helical piles with small-diameter shafts, adhesion contributes little to the overall capacity and torque of the pile, so PWP changes are not typically considered in determining pile capacity. In modern construction, the use of larger diameter helical piles has become very common. For large-diameter helical piles, changes in PWP immediately adjacent the shaft can be quite large during installation. Increased pore water pressure and reduced adhesion can have a temporary effect on pile capacity and installation torque.

Jan 1, 2018

By Ali Ameli

Design loads are limited for piles relying upon toe stresses in rock due to uncertainty about the rock quality over the whole pile diameter because of rock mass properties or construction effects. The paper discusses the use of video images to evaluate rock quality at the bottom of piles socketed into graniodorite bedrock in a steel pipe pile project. Skillful interpretation was required to assess the 3D properties of the rock from video images. It is necessary to observe the rock mass characteristics near the project site for better perception of the rock features from the images. Video image interpretation skills were established by the evaluation of the cores drilled under the socket base and the results of pile loading tests. Correlations were found between rock appearance in the images and the rock socket drilling records. Rock socket acceptance criteria were developed through monitoring the drilling operations for the specific site procedures. Video images then served as one of the quality-assurance tools together with probing and pile loading test. Lessons and methods learned from video inspection in this project could be used to evaluate rock quality in similar cases.

Jan 1, 2006

By Louis M. Schlesinger, Michael J. Garska, Joel F. Hutwelker, James T. Jr. Tanner

A pilot plant was constructed and operated to investigate the column flotation of 20 x 200 mesh North Carolina phosphate ore, using high throughput, high solids operating conditions developed at the NCSU Minerals Research Laboratory. Flotation was performed at 45% solids in a 9.5 cm (3.75 in.) diameter by 2.26 m (7.4 ft.) tall column at throughputs of 19.1 t/hr/m2 (2.0 stph/ft2) and 31.7 t/hr/m2 (3.3 stph/ft2). Recoveries in excess of 98% of the phosphate value were obtained at the lower throughput -- while obtaining concentrate grades containing over 28% P205 (61.2% BPL) at that recovery. Recoveries of about 95% of the phosphate value were obtained at the higher throughput, while making a concentrate averaging 27.6% P205 (60.3% BPL). In addition, a better understanding of the variables governing the column flotation of coarse nonmetallic minerals was gained. Variables examined included superficial air velocity, throughput (superficial feed velocity), frother type, frother dosage, and bias rate.

Jan 1, 1993

Remediation of Mine Seepage at Batu Hijau

Sep 13, 2010

By Serge Moalli

The Ashlu Creek Hydro-electric project, located north of Squamish, BC, at the confluence of Ashlu Creek and the Squamish River, comprises a 49 MW run-of-river project and features a 4.08 m diameter, 4.4 km power tunnel and a 128 m deep drop shaft. The Ashlu Creek Hydro-electric project is being developed by Innergex under Ashlu Creek Investments Limited. Site civil works are being completed by Ledcor CMI of Vancouver with tunnel construction by Frontier Kemper Constructors ULC under a lump sum design-build contract. Site works got underway in September 2006 with the construction of the tunnel portal and laydown area. These site works required rock slope stabilization over a 50 m rock slope to secure the laydown area as well as the construction of a tail track muck tipping station and structural wall to facilitate TBM excavation and spoil removal. Starter tunnel construction commenced in early 2007 and TBM tunneling started in the late spring of 2007 and is planned to continue until early 2009. The power tunnel is being excavated using a 1,200 kW Wirth open-type hard rock TBM dressed with 31?17' cutters. The TBM featured two fixed mounted rock bolt drills behind the finger shield: these were removed and replaced with jacklegs to improve access. A probe drill at the end of the main beam is also present. The geology along the 4.4 km power tunnel comprises very strong and generally massive granitic bedrock with rock strength greater than 225 MPa. A unique feature of the project is that no subsurface investigations have been completed for the tunnel however extensive bedrock outcrops are present along the Ashlu Creek valley. A historical quarry exists approximately mid-way along the tunnel alignment that has exposed good quality granitic bedrock. TBM tunneling to date has achieved advance rates of 10?20 m/day with a maximum of 23 m and has encountered all of the anticipated six major fault zones where the installation of various standard high capacity tunnel support was successful to facilitate TBM advance through these sections.