Search Documents

By Alireza Zakeri

To evaluate the behavior of minor elements in the copper smelting process, activities of silver, selenium and tellurium at minor concentration were determined at 1473 K within the miscibility gap of the Cu-S-Me (Me = Ag, Se, Te) and Cu-Fe-S-Me systems varied in Fe/Cu ratio. Phase relations between the immiscible metal and matte phases in the foregoing systems were first established by a quenching technique at 1473 K to supplement the activity measurement data. A Knudsen-effusion mass spectrometer, capable of handling complex gaseous systems and relatively small vapor pressures, was adopted for activity determination. Using a multiple Knudsen-cell, the ion intensity of minor element in the sample under study was measured simultaneously with that in a reference sample. Activity was obtained from the ratio between the measured ion intensities as well as the known activity value of the minor element in the reference sample. Limiting activity coefficients of the minor elements were correlated with composition of the matte. Based on the experimental results, the vaporization behavior of the minor elements has been discussed.

Jan 1, 1999

By A. S. Mustafinova, A. A. Zharmenov

"Production of electrolytic copper is characterized by large volumes of acidic spent solutions the utilization of which requires considerable expenditures of neutralizing agents. At present, an economically substantiated technology does not exist for treatment of sulfuric acid rinse solutions and spent copper electrolyte which will allow for repeated use of the acid and the metal salts. Therefore, for this aim the most advantageous is the use of electromembrane methods. In the paper there is stated the essence of developed technologies which are distinguished by low waste and provide the extraction from the solutions of metallic copper, nickel and sulphuric acid. There are also considered methods of copper electrolyte processing allowing to regulate its composition by that or another component (H2S04, Cu, Ni, As).On the base of the detailed study of the behaviour of various types of ion- exchanger membranes in copper-, nickel-, zinc-, arsenic- bearing sulphate solutions there is realized the selection of the most suitable membranes (MK -401, MA-411, MB-2 and MKL-l/MAL-2).Some variants of electro membrane processing of spent solutions of the hydrometallurgy process have passed productions tests on a number of copper-electrolyte enterprises of the countries of CIS (cooperation of Independent States). These tests showed high efficiency of developed methods."

Jan 1, 1997

By W. L. Dalmijn, E. A. Schokker, N. Fraunholcz, P. C. Rem

Many processes developed for the mechanical processing of Automotive Shredder Residue (ASR) suffer from high processing costs. We offer a distinct concept for low-cost mechanical processing still allowing high value-added recycling of the recovered materials. The basic idea behind this approach is to produce saleable pre-concentrates at the lowest possible costs that can be further processed in existing separation facilities. Our process includes screening, size reduction and magnetic separation. Preliminary studies showed that fibers in ASR are magnetic due to adhering rust particles allowing separation into a fiber fraction and a non-magnetic rigid fraction by high-intensity magnetic separation. The fiber fraction is most suited for thermal processing. The rigid fraction mainly consists of plastics and rubbers with up to 10 wt.-% of non-ferrous metals, some inert material and copper wires. This fraction is very well suited for mechanical processing by, e.g., sink-float separation in existing metal separation plants. The non-metal fraction can be processed further to recover the plastics and rubbers. The process proposed in this study is expected to be substantially cheaper than full thermal processing. In addition, as it mainly relies on existing separation facilities, it can be applied in the short term.

Jan 1, 2000

By Michael Meyer

In the past shredder fluff was discarded in landfills, but shrinking landfill space and the partly hazardous content of the fluff as well as its caloric value, all resulted in efforts to turn this waste problem into a an energy resource. In order to produce a fuel, the inorganic compounds have to be removed. Extensive analyses and particle size measurements were made on fluff from various shredder. For optimal separation all particles are reduced to a uniform, relatively small size. In a subsequent combined - screening and air classification - process, successful separation into organic and inorganic fractions is achieved. The inorganic fraction is treated in a heavy media or an eddy-current separator to recover the valuable metals, while the organic fraction is now suitable for thermal processing, such as fluidized bed gasification and using the resulting carbon as a chemical reagent.

Jan 1, 1995

By Harry Littleton, Jr. Scarber, Wanliang Sun

"The Lost Foam Casting (LFC) process is relatively immature when compared to other casting processes. To make the process more robust, computer modeling is needed to reduce lead times and casting defects. In this study, metal filling of lost foam aluminum castings was visualized using state-of-art real time X-Ray technology. Metal filling of the lost foam casting was simulated using a commercial software package. The result of the computer simulation was compared with the results of the real time X-Ray visualization. Some of the computer simulation results agreed with the real time X-Ray visualization, but some did not. Based on other studies using real time X-Ray technology, new input variables, such as foam density variations, were developed for the computer modeling. With the new variables, modeling of the lost foam casting process becomes more realistic. IntroductionMold filling of the Lost Foam Casting (LFC) process is an important step toward making a quality part. In the LFC process, molten metal is poured against a refractory coated foam pattern surrounded by dry sand. At the pouring temperature of aluminum, the foam pattern is decomposed into 30% (wt) gaseous and 70% (wt) liquid foam pyrolysis products. Existence of the gaseous foam decomposition products significantly increases the back pressure on the metal stream compared with the conventional open cavity sand mold. Entrapment of the liquid pyrolysis products during the metal filling generates many casting defects, such as internal pores, fold and blisters. Existence of these casting defects sometimes seriously degrades the quality of the components manufactured by the LFC process. Understanding and controlling the metal filling of the LFC process will certainly make this process more robust."

Jan 1, 2004

By Songlin Zhang

"The McCoy/Cove mine, located in Eureka-Battle Mountain trend of Nevada, is a gold and silver deposit. Case studies of recoverable reserve estimation for gold and silver were made using multiple indicator kriging and volume variance correction. The grade tonnage distributions of recoverable reserves were constructed and compared with the distributions defined by blast hole assays. Optimal pits were generated by Whittle 4D pit optimization package to analyze the impact of different processing recoveries at different economic cutoffs. The results were compared with ordinary kriging. The study indicates that the proposed method for multi-mineral recoverable reserve estimation is more accurate than kriging in tenns of grade and tonnage. The method of using recoverable reserves for pit optimization will maximize global reserve recovery and revenue, and is more efficient than condition simulation regarding computing power.ABSTRACT ONLY"

Jan 1, 1997

By Mikael Ersson

A fundamental mathematical model of lance blowing on a bath surface has been developed with a purpose to increase the understanding of various phenomena in top blown oxygen converters. The model is based on the Navier-Stokes equations and turbulence is predicted using the k-model. In the present model the deformation of the liquid surface, caused by the impinging gas jet, is described using a VOF formulation. The mathematical model results have been verified by comparing predicted penetration-depth data with experimental results from physical model trials. The fluid dynamic modeling has also been coupled with the thermodynamic modeling to predict the reaction rate/distribution occurring in the vessel. The focus has been on carbon and a qualitative comparison of the predicted carbon content in the hot spot area and in droplets with experimental data from laboratory trials has been done.

Jan 1, 2006

By Ray D. Peterson, Annette Revet

The optimization of secondary aluminum furnaces is critical to the efficient operation of a recycling facility. Since all metal loss occurs in the drosses, physical and chemical analyses of these by-products are valuable diagnostic tools. Dross analyses can provide information concerning total furnace metal recovery efficiency as well as identifying areas for potential improvements. A complete dross analysis is a labor-intensive process that requires significant care both in sampling and performing the analytical techniques. Experiments can be done at a bench- or plant-scale depending on the facilities available. This paper outlines the benefits and information that can be generated through dross studies. Furthermore, several analytical methods are discussed as well as the special requirements needed to gain accurate results. Experimental data from industrial studies is provided to demonstrate the use of dross evaluations for ~ace optimization.

Jan 1, 2000

By P. J. Harrington

The recovery and recycling of low concentration metal and other ions has traditionally been carried out using adsorption or ion exchange processes which, however, become uneconomical at higher concentrations, such as those that occur with many intermediate or waste streams where recycling is now being required. This paper describes the development of a process based on non-dispersive solvent extraction for the recovery of chromium (VI) from electroplating rinse water. During the chromium plating of steel, the concentration of chromium (VI) in the rinse bath rises to concentrations in the order of 100 mg/L when it becomes unusable and is then disposed of. The aim of this work was to investigate processes for recovery and recycling of the chromium in the rinse bath. The recovered chromium is required to be concentrated and purified before reuse. Tertiary amines have been shown capable of concentrating and purifying the chromium (VI) in solution. However, solvent extraction processes that have been applied to the recovery and reuse of metals from waste streams have had only limited success in the past, primarily because of the relatively high solvent losses when existing contacting equipment is used on low feed concentrations. Attempts to eliminate losses by immobilizing these complexing agents on substrates have not been successful. In order to control the losses and maintain specificity, a hollow fibre-contained liquid membrane has recently been trailed in a pilot plant to recover chromium from chromium plating waste streams. Details of the trial and modeling of the results are presented, and show that the level of losses is significantly reduced. However, issues relating to fouling still need to be addressed. This type of equipment has many applications in the recovery and recycling of a range of materials in the manufacturing processes.

Jan 1, 2003

By J. Partinen

Drying is a unit process which has numerous applications in metallurgical process industry. Kumera Technology Center, being a worldwide equipment and process supplier, has developed sophisticated solutions for both direct and indirect drying. In conventional direct drum drying, the energy is taken from combustion of fossil fuels, requiring energy input and emitting considerable amount of off gases. In modem copper smelters, thermal energy from the off gases is recovered in waste heat boilers making the steam available. Using that steam as the energy source for concentrate drying, the total volume of off gases can be considerably reduced and releasing of harmful combustion gases into the atmosphere can be avoided. Kumera Technology Center has recently developed and promotes a new steam drying process for drying of copper concentrates. In the development of the new dryer, Kumera's approach has been to combine the best properties of both the steam dryers and the drum dryers. In the design special attention has been paid to overcome problems of excessive wear and clogging and to reduce the required maintenance operations. In this paper the environmental issues and energy consumption related to both direct and indirect drying processes are discussed. The estimated operation costs and emission levels are compared, based on calculations and the data collected from industry. Finally, the development project of the Kumera Steam Dryer is briefly reviewed

Jan 1, 1999

By Neil Smith

Mineral processing plants typically procure a range of industrial services from contractors. Their satisfaction and value received is directly affected by how the services are procured, rationalized and delivered. Conventional purchasing strategies often focus on price rather than on optimizing the service relationship between supplier and customer. The nature of this relationship may have the greatest potential to reduce costs and enhance production. It has been documented that a service involves simultaneous production and consumption. A high degree of customer involvement is often necessary for a successful outcome and the expectations and attitudes of the customer can positively or negatively affect delivery of the service. This indicates that the customer can enhance or diminish their own satisfaction and value received and the supplier cannot act alone for best results. The Optimax? Program for industrial services is a service delivery framework whereby a customer and supplier work together to raise the efficiency of the service exchange. The Optimax? Program is intended to help the customer optimize costs and maximize production by connecting the customer and supplier through shared information and objectives. This paper will review the basic nature of services, provide a couple of examples of conventional procurement strategies for services and outline the features of the Optimax? Program. A Case Study showing recent results from implementing the Optimax? Program will be included.

Jan 1, 2006

By Wenbo Luo, Kang Liu, Fusheng Mao, Jilai Xue, Jun Zhu, Chunlei Yang

Extracting alumina from coal fly ash (CFA) is of great interest for both environmental protection and recycling valuable alumina content. In this study, ultrasonic aided leaching process as an effective method was investigated to enhance extracting Al2O3 from CFA via concentrated sulfuric acid sintering. The influence of ultrasonic power and processing time were tested under the conditions as the same as those without ultrasound. It is found that the alumina extraction rate can reach 90.5 % with ultrasound assistance, while the ultrasonic treatment can reduce almost 15 ~ 30 min in leaching time and 5 ~ 10 oC in leaching temperature than those without ultrasonic operation at the same Al2O3 extraction rate. In addition, the ultrasonic can reduce calcium content by 6 ~ 8 % dissolved into the leaching liquid. SEM analysis also shows that the residue particle size with ultrasound is smaller than that without ultrasonic treatment.

Jan 1, 2015

By Bruno Augusto Batista Ribeiro, Felipe Terra Elias, Wagner Moulin Silva

In the pyrometallurgical production of copper from its sulfides, converting in the Peirce Smith (P-S) Converter is still the most widespread method to obtain white metal and blister copper from the matte. Despite the fact of being a century-old process, it is still possible to achieve improvements in the process, by the use of modern tools, one of the most valuable being numerical calculation and computer-aided simulation. The present study presents three cases in which the angle for the gas injection and the number of working tuyeres are changed during the slag blow phase of the converting process. It was noticed that a decrease of the number of tuyeres, followed by an increase in the injection gas velocity, results in improved reaction volume and less stress to the refractory lining. However, an increase in the amount of copper lost to the slag as oxide is likely to occur.

Jan 1, 2014

By Virgil Optasanu, Yvon Lacroute, Eric Lesniewska, Tony Montessin, Pauline Vitry, Eric Bourillot, Cédric Plassard

A general challenge in metallic components is the need for materials research to improve the service lifetime of the structural tanks or tubes subjected to harsh environments or the storage medium for the products. One major problem is the formation of lightest chemical elements bubbles or different chemical association, which can have a significant impact on the mechanical properties and structural stability of materials. The high migration mobility of these light chemical elements in solids presents a challenge for experimental characterization. Here, we present work relating to an original non-destructive, with high spatial resolution, tomographic technique based on Scanning Microwave Microscopy (SMM), which is used to visualize in-depth chemical composition of solid solution of a light chemical element in a metal. The experiments showed the capacity of SMM to detect volume. Measurements realized at different frequencies give access to a tomographic study of the sample.

Jan 1, 2015

By I. A. Ibrahim

Ilmenite, in its natural form, is an inactive mineral from which the selective removal of iron is rather difficult. The reactivity of ilmenite. so that it can be leached with dilute hydrochloric acid, can be enhanced by chemical reduction in solution using a suitable metal as a reducing agent. The present paper aims at the evaluation of an Egyptian ilmenite ore for the production of synthetic rutile by direct leaching with hydrochloric acid in presence of iron powder. In this process, the titanium and iron contents are dissolved; meanwhile, the dissolved titanium is hydrolyzed and re-precipitated leaving mainly iron in solution. Leaching conditions were optimized to obtain less iron in the final solid product. Addition of sufficient amount of iron powder during leaching reduces the dissolved Fe3+ to Fe2+ and reduces the dissolved Ti4+ to Ti3+. The creation of Ti3+ in solution is assumed to have a role in dissolving the ferric iron and hence increasing the reactivity of the ilmenite ore. Synthetic rutile of about 90% TiO2 and 0.77% Fe2O3 was obtained from ore with a grain size 100% passing 200 mesh and a 5-hour leach time with 20% HCl at boiling temperature (110°C) and 0.11 g iron powder / g ore.

Jan 1, 2003

By Nathaniel Arbiter

The first ammonia leaching plants, applied to copper carbonate and native copper tailings in 19 15, were followed more recently by research and development of flowsheets for ammonia leaching of sulfide concentrates. These were applied to two commercial plants. Anaconda's Arbiter Plant started up in 1974 with a design capacity of 36,000 tons/year of cathodes, to be produced by ammonia leaching with oxygen, followed by solvent extraction and electrowinning. The plant shutdown in late 1977 as a result of high maintenance and operating costs, partly due to harsh winters; to complications associated with sulfate disposal; and to changes in mineralogy. BHP's Coloso plant in Chile was designed to produce 80,000 tons/year of cathodes by leaching part of Escondida's concentrate production. Using a similar flowsheet but with air and low temperatures to avoid sulfate production, it started up in late 1994 and shutdown in mid-1998, after failing to reach cathode design capacity, and experiencing problems with its technology. The paper reviews the technologies and also alternative methods for overcoming the problems.

Jan 1, 1999

By F. A. Fasoyinu

The mechanical properties of yellow brass (C85800), high strength yellow brass (C86300), and high manganese brasses (C99700 and C99750) cast in permanent molds have been studied. The tensile properties as well as fracture and impact toughness of these alloys are strongly dependent on the chemical composition. Alloys and/or compositions exhibiting relatively high zinc equivalent often exhibited high ultimate tensile strength and yield strength with significant reduction in ductility (% elongation). In order to achieve optimum properties with a good balance between strength and ductility, a calculation of the zinc equivalent before alloy preparation can be useful.

Jan 1, 1999

By C. H. Quan

Solvent extraction tests were carried out on a rare earth chloride solution derived from monazite processing to determine the effect of extractant and diluent on the distribution coefficients between organic and aqueous phases, and the separation factor between rare earths. The extractants were 20% by volume di-2-ethyl-hexyl phosphoric acid (DZEHPA) or 2-ethyl-hexyl phosphonic acid (Ionquest® 801). Four Shellsol diluents were tested ranging from nil to 100% aromatic content. D2EHPA gave the highest rare earth extraction for a given pH but was less selective than Ionquest. The geometric mean separation factor between adjacent rare earths varied from 2.41-2.56 for D2EHPA to 2.62-3.01 for Ionquest. The nil-aromatic diluents (Shellsol 2037 and 2358) gave better separation factors in Ionquest but, in D2EHPA, were slightly inferior to the 100% aromatic diluent Shellsol AB. Yttrium behaved as a pseudo-heavy rare earth with a distribution coefficient lying between Ho and Er, as expected from its ionic radius.

Jan 1, 1992

By D. L. Stewart

"Melt loss is usually one of the highest individual cost items in the operation of ah ingot casting facility. While melt loss and the resulting cost for the entire facility is usually well known (at least via standard cost accounting), dross generation and melt loss for individual unit operations within the plant are usually not known. Thus, the financial impact of various practices, alloys and scrap types is not known. Development of an accurate, relatively low-cost technique for measurement of melt loss at commercial scale would aid in understanding melt loss for existing units, as well as evaluation of the melt loss impact of alternate processes.This paper will describe a methodology developed at Alcoa for accurate and inexpensive measurement of melt loss at commercial scale. The methodology has been used to evaluate the impact of scrap type, melting practices, and dross treatment technology on melt loss."

Jan 1, 2000

By F. Tailoka

In order to decrease the voltage required for electrorefining, a recessed electrode cell has been developed in which the anode and cathode have recesses machined into their faces. The anode and cathode plates are separated by a thin refractory cloth and the cell is filled with fused salt. Bismuth containing 10 to 90 % lead with copper and silver as minor impurities has been electrorefmed at a current density of 10,000 to 20,000 Am-2. The cell voltage was between 285 and 635 millivolts and the bismuth was refined to a purity of 99.9 %. Flow patterns were observed in a room temperature model of the recessed channel cell using water and mercury to simulate molten metal and the fused salt electrolyte. The flow in the electrode recesses is characterized by discrete droplets when the liquid flow rate is low and thin streams and rivulets at higher flow rates.

Jan 1, 1995