Search Documents

By Gerardo R. Alvear

The ability to efficiently remove impurities contained in concentrates is a key point to consider when selecting copper smelting technology for new plants or modernisation projects. Volatilisation of impurities such As and Sb should occur as early as possible in the process, and preferably in the smelting furnace, so that they do not impact on downstream unit operations. The ISASMELTTM process has been demonstrated to remove impurities efficiently, through high levels of volatilisation. This behaviour is promoted by attributes of the process such as the strong bath agitation, and the flexible nature of the process design, allowing the operator to choose the optimal matte grade for impurity partitioning, and the positive effect of the moisture content in the feed. This paper presents the distribution of minor elements in the copper ISASMELTTM furnace. Distribution impurities of As, Sb, Pb, Zn and Co observed in the ISASMELTTM furnace at Mount Isa Smelter are reported. Then, based on plant results and thermodynamic considerations, the potential application of ISASMELTTM technology for processing complex concentrates is discussed.

Jan 1, 2006

By Yuri Bychkov

The Electron Beam Melting is the most efficient technology for metals and alloys refining. For ,secondary metals processing the Electron Beam Skull Melting (EBSM) with the electromagnetic stirnng (EMS) of melt in the crucible was shown to be the most appropriate. The copper produced by EBSM with EMS possesses higher density and electric conductivity in comparison with other refining methods. The details for high power electrical machines were cast of the copper waste refined by EBSM technology.

Jan 1, 1995

By Matthew Jeffrey

Leaching, cementation, electroplating and flotation are all electrochemical phenomenon. They are also key processes in the hydrometallurgical treatment of metals. Unfortunately electrochemical methods tend to be under-utilized when studying these processes and one possible reason for this is the confusion surrounding the large number of electrochemical techniques available. In this paper four former PhD students of Professor Ian Ritchie present an insight into how one electrochemical technique can be used to compliment rate/kinetic studies. The paper details how to perform the experiments, interpret data, and recognize complications with the results. Examples where this approach has been highly successful are presented, and include: cementation of zinc by aluminium, cementation of copper by nickel, cyanide leaching of gold and the cementation of gold thiourea by mild steel. The examples illustrate that this universal approach adopted by Ian Ritchie provides the key to understanding the mechanism of many hydrometallurgical reactions.

Jan 1, 2003

By Xingye Guo, Yeon-Gil Jung, James Knapp, Zhe Lu, Jing Zhang, Li Li

La2Zr2O7 is a promising thermal barrier coating material due to its low thermal conductivity and superior high temperature stability. In this work, Bilayer La2Zr2O7 and conventional 8 wt% yttria stabilized zirconia (8YSZ) coatings were deposited using plasma spray technique. Both singlelayer La2Zr2O7 and double-layer 8YSZ/La2Zr2O7 coating architectures were designed. Thermal cycling and thermal shock tests were used to evaluate coatings’ thermomechanical properties. All La2Zr2O7 coats were delaminated in the furnace cycle test in less than 20 cycles. This is because residual thermal stresses accumulated during thermal cycling. In the jet engine thermal shock (JETS) tests, the SCL La2Zr2O7 and DCL dense 8YSZ/La2Zr2O7 coatings were fully delaminated. In contrast, the DCL porous 8YSZ/La2Zr2O7 coating sample only partially delaminated on the edge. This is because of the porous 8YSZ layer provides strain compliance. The findings will help to propose efficient thermal barrier coating systems.

Jan 1, 2016

By Ximena Diaz

Mercury is one of the most undesirable contaminants in gold bearing ores. During cyanidation mercury cyanide compounds accompany gold in all the extraction and recovery processes. Of course mercury in the carbon eluates creates environmental problems in subsequent refining steps. One possible process alternative for the separation of gold from mercury in such concentrated alkaline cyanide solutions is the selective solvent extraction of gold by undiluted Dibutyl Butyl Phosphonate (DBBP). In order to describe the behavior of mercury during extraction by DBBP, the results from a preliminary research program are presented. In this study, temperature and cyanide concentration have been found to be the most significant variables which influence the separation of gold from mercury by solvent extraction using DBBP. It was found, using plant eluate from a carbon strip, that excellent separation of gold from mercury can be obtained at 60' C with 98% gold recovery and complete mercury rejection in a single stage of extraction. The influence of pH is also discussed in terms of the extraction chemistry. These results complement previous research which described the DBBP solvation extraction of an aurocyanide ion pair. In addition, these results extend our understanding of the alkyl phosphorous ester extraction systems by illustrating that neutral ionic species such as Hg(cN)02sq, can be extracted at low cyanide concentrations, a phenomenon which had not been observed previously for other cyanoanions.

Jan 1, 1993

By Y. H. Liu

Several foaming aluminum samples of different density were prepared in a semi-industrial scale experimental system. Their properties such as the energy absorption characteristics, mechanical properties, heat conductivity and acoustical properties were measured. The results showed that the foaming aluminum with a density of 0.5 to 0.6 g/cm3 has the best energy absorption and this makes it suitable as the ensuring bar of the automobiles and also as a cushion material for the engine. The foaming aluminum with a density of 0.25 to 0.4 g/cm3 has the best acoustical properties and heat conductivity resistance, which is suitable for the door filling material, the ceiling and the partition of the car engine.

Jan 1, 2003

By Manuel Zamalloa

The outstanding metallurgical performance of the Noranda continuous converter (NCv) in operation since November 1997 has allowed the company to meet production and environmental targets. This achievement positions this new technology as a strong alternative continuous converting technology for copper production. Knowledge of slag chemistry has been important in this respect. The purpose of this paper is to discuss the effect of key parameters including temperature, oxygen potential, slag composition and levels of copper oxide in slag on the conditions leading to magnetite precipitation, as well as on the conditions affecting the liquidus ranges of NCv slag. The above variables are evaluated using industrial data and thermodynamic predictions. Practical implications of customizing operational fluxing procedures to determine optimum operating windows are also discussed.

Jan 1, 1999

By Y. H. Liu

Several foaming aluminum samples of different density were prepared in a semi?industrial scale experimental system, Their properties such as the energy absorption characteristics, mechanical properties, heat conductivity and acoustical properties were measured. The results showed that the foaming aluminum with a density of 0.5 to 0.6 g/em3J has the best energy absorption and this makes it suitable as the ensuring bar of the automobiles and also as a cushion material for the engine. The foaming aluminum with a density of 0.25 to 0.4 g/em3 has the best acoustical properties and heat conductivity resistance, which is suitable for the door filling material, the ceiling and the partition or the car engine.

Jan 1, 2003

By Dariusz Kopyci ski, Józef Dorula

The study proves that by introducing the iron powder and disintegrated steel scrap to low-sulphur cast iron still before the inoculation carried out with a conventional graphitising inoculant, the mechanical properties similar to those obtained during the inoculation treatment carried out on cast iron with the recommended high sulphur content are achieved. The said operation increases the number of crystallisation nuclei for dendrites of the primary austenite. In this case, the iron particles act as substrates for the nucleation of primary austenite, due to a similar crystallographic behaviour of the regular face centred cubic lattice The more numerous are the dendrites of primary austenite, the less free space is available in the interdendritic spaces for the formation of graphite eutectic grains, which makes the structure more refined (more eutectic grains) and the mechanical properties higher.

Jan 1, 2016

By Richard LeSar

Sustainability requires more from engineering than the development of technology. Engineering must also take into account the effects of that technology on the integrated social, economic, and environmental processes that constitute our society. Schumacher introduced the powerful concept of an appropriate technology, by which he meant a technology that is appropriate to the environmental, educational, cultural, and economic situation for which it is intended. While the principles of appropriate technology have been most commonly applied in the developing world, they are equally valid in the developed world as well. In this paper we will review appropriate technology and discuss its role in helping to define a way to think about this broad view of sustainable engineering. We will end by presenting one strategy for introducing the concepts and applications of appropriate technology in an engineering curriculum.

Jan 1, 2010

By Peng Bing

Stainless steelmaking dust is classified as a hazardous waste due to higher than acceptable heavy metal leachabilities such as zinc, lead, cadmium and chromium. In addition to being an environmental hazard, the flue dust is also an economical concern to stainless steelmakers as it contains large amounts of valuable alloying elements, especially for iron, chromium and nickel. A new technology of direct recycling of stainless steelmaking dust has been developed to recover the metals from the dust. But it was found that zinc was accumulated in the dust collection system in practical run of direct recycling. This study focuses on the effect of the operating parameters such as temperature, dust feed rate and the ratio of CO to dust on the reduction of zinc oxides present in the dust. The mathematical model for the reduction process was setup based on the experimental research. According to the mathematical model, the temperature has obvious effect on the reduction of zinc. It is benefit to the process of zinc reduction to increase the temperature. But the temperature will not be the main factor for the reduction process after 1228C. It will promote zinc reduction to decrease the dust feed rate and control the ratio of dust to CO. It was also found from the experiments that ZnFe2O4 in the dust could be decomposed at high temperature. Decomposing ZnFe2O4 in the dust increases the recovery of zinc from the dust distinctly.

Jan 1, 2006

By Alfonso Nájera

Turbulent flow of liquid steel and its control is studied using different geometries of turbulence inhibitors. Four designs of turbulence inhibitors were characterized through experiments of tracer injection I a water model and mathematical simulations using the Reynolds Stress Model (RSM) of turbulence. Geometries included octagonal-regular, octagonal-irregular, pentagonal and squared. A layer of oil was used to model the behaviour of tundish flux during steel flow. Fluid flows in a tundish using these geometries were compared with that in a bare tundish. Experimental and simulation results indicate that the flow in the bare tundish and a tundish using turbulence inhibitors open large areas of oil due to strong shear stresses at the water-oil interface but the squared inhibitor. These phenomena are explained by the high gradient of the dissipation rate of the turbulent kinetic energy using the squared inhibitor. Using this device the kinetic energy reports a high gradient from the tundish floor to the free bath surface as compared with other geometries.

Jan 1, 2006

By W. Gong

Their outstanding thermal stability and high energy product make Sm(Co,Fe,Cu,Zr),-type alloys attractive for advanced applications. The near net-shape production of Sm(Co,Fe,Cu,Zr), bonded magnets make them potentially superior to any magnets made by sintering. Although pioneering work done by Shimoda et al. and other investigators provide insights on the proper compositions and process control of this alloy system, additional work is still necessary to improve our understanding of alloy behavior at various processing stages and to increase the production yield during powder processing. In this paper we report on the development of anisotropic Sm(Co,Fe,Cu,Zr), alloy powders for the bonded magnet application. Our focus is on the development of a moderate coercivity powder requiring a relatively low magnetizing field to charge the magnets to their optimum Br, Hci and BHmax. The magnetic properties are related to the evolution of the microstructure at various processing stages and the average particle size and size distribution of powders.

Jan 1, 1997

By Pan Cao

The process of reduction roasting of nickel laterite with rotary hearth furnace combined with magnetic separation becomes a very potential way to prepare ferronickel alloy, especially for the low grade nickel laterite ore. In order to realize this new process, the effect of roasting temperature, time and additive on the reduction degree were investigated in the laboratory experimental. The results indicated that the recovery rate of Ni increased with the roasting temperature increasing to 1500°. Most of nickel and a spot of iron are selectively reduced with adding 25.19% SiO2, 6.42% coal, and roasting for 60min at 1500℃. Then conventional magnetic separation was carried out. The content of Ni and Fe are 7.50% and 59.08% in ferro-nickel nugget prepared by this method. And the recovery rate of Ni is 90.91%, which indicates that a high recovery of ferro-nickel from nickel laterite ore is achieved indeed.

Jan 1, 2014

By Jeong-Hwan Kim

The liquid-liquid reactive process (solution process) is often adopted as a synthetic method for precipitated calcium carbonate (PCC) in laboratory studies for its simplicity in operation or ease in controlling process variables. Still, PCC are produced commercially by passing carbon dioxide through a milk of lime, i.e., by a gas-liquid reacting method (carbonation process). Few studies on the carbonation process have been conducted, since the process variables are interrelated and difficult to control compared to the solution process. In this study, both carbonation and solution processes were employed to study the polymorphs of calcium carbonate and growth rate of PCC crystals. The effects of the characteristics of limestone ores as a raw material in the synthetic system of PCC on the synthetic characteristics of PCC were also investigated. To control the nucleation rate in the synthetic systems, the shape factor was considered most important. Single-phase aragonite PCC could be synthesized under a variety of controlled experimental conditions such as ionic strength, solution composition, concentrations of additive ions, and temperature.

Jan 1, 2006

By A. P. Paiva

With the aim of establishing a valuable alternative to the conventional methods, studies regarding the recovery of precious metals by solvent extraction have been increasing over the past few years. In this work, the selectivity of extraction presented by Cyanex 471X toward silver is investigated. Simulated chloride solutions considering contents of iron and copper usually present in actual leaching practice were used. The characterization of the aqueous solutions - in terms of the multiple equilibria established by the chlorocomplexes of the different metals and their relation to the total chloride concentration of the base-electrolyte - was successfully carried out by cyclic voltammetry. The results obtained support the important contribution of the electrochemical techniques for the understanding of the overall extraction phenomena.

Jan 1, 1994

By Tetsuro Sakai

Home appliance recycling law was put into force in April 2001 in Japan. Specified kinds of home appliances, such as air conditioners, television sets, refrigerators and washing machines, should be recycled according to the law. Mitsubishi Materials Corporation (MMC) in cooperation with home appliance manufacturers is operating five home appliance recycling plants in Japan. MMC established complete treatment system of recyclable materials generating from home appliance recycling plants, which is formed by unique collaboration among home appliance recycling plants, copper smelter and refinery, and cement plants. Recyclable materials containing copper and precious metals are only handled and treated within the MMC group. By using this lock-in system, safe treatment and traceability of materials are guaranteed as 100% materials recycle.

Jan 1, 2008

By A. V. Tarasov

The high efficiency of autoclave processes is attributed to the fact that they are suitable for processing of refractory raw materials, have low capital costs and high productivity, ensure integrated utilization of the feed materials, produce innovative saleable products, completely eliminate any air emissions, provide low-waste or waste-less technology, as well as mechanization and automation of production processes. In the immediate future, it might be expected that autoclave processes will find use on commercial scale for production of heavy non-ferrous metals in combination with other processes (hydrometallurgical, upgrading, sorption and solvent extraction, electrolytic, etc.) to ensure: -Integrated processing of refractory ores and concentrates (pyrrhotite, zinc, copper-zinc, lead-zinc, nickel-cobalt, copper, pyrite); -Production of metallic powders of base metals as commercial products (copper, cobalt, nickel, etc.), composites on their bases, final products and saleable salts. Processing technologies incorporating autoclave processes, especially, at the stage of liberation (chemical upgrading) of minerals, are characterized generally by high overall recoveries of valuable constituents significantly exceeding recoveries common for conventional pyrometallurgical processes (for some elements by several tens of percent). An example is processing of low-grade refractory pyrrhotite concentrates using autoclave liberation of feed material under pressure of a new reagent, i.e., sulfur dioxide. The use of sulfur dioxide ensures a significant improvement in the recoveries of non-ferrous metals and platinoids to sulfide concentrate and smelting of the latter increases the capacity of the smelting units employed and minimizes the yield of discard slag and loss of metals in slag; in addition, it resolves the problem of sulfur dioxide utilization.

Jan 1, 2003

By Yoshimasa Oda

The tank house of Tamano Smelter has adopted a high current density electrolysis operation applying PRC (Periodic Reverse Current) method and before 1991, it had materialized both high production capacity of 161,000 tons/year and high labor productivity. However, recent rapid rise of Japanese currency in foreign exchange market has urged us to further exert our efforts in reduction of labor cost. In order to achieve this goal of labor cost reduction, we have completed, in 1994, our phase four production expansion project which incorporated significant re-structuring of the organization and we have accomplished annual production of 191,000 tons/year. This project can be outlined as increase of number of cells for electrode exchange per day in the commercial electrolysis process to meet the increased number of cells and increase of the capacity of impurity treatment process. These improvements were done with minimum installation of new equipment and facilities and with achievements in efficiency and manpower saving of the existing facilities. Together with these improvements, rationalization in the starting sheet section was carried out by changing the material of mother blanks as well as changing their maintenance procedures. At the same time, the crane in this section was modified to enable automatic operation by a fuzzy control. As a result, we were able to save manpower equivalent to 5 operators in this section. With these improvements, the production capacity was increased by 18% and labor productivity by 25%.

Jan 1, 1996

By James D. Navratil

Although liquid membranes have several advantages over conventional liquid-liquid extraction, problems such as membrane instability remain. In order to solve these problems, we have combined an electrostatic field with the principle of liquid membranes and developed a novel reactor system for rare earth recovery. Our cylindrical reactor, filled with extractant and diluent, is divided by means of a perforated cylinder into an outer annular extraction cell and an inner stripping cell. Below the extraction and stripping cells are two settlers for the aqueous solutions. The design of the reactor permits the organic solution to flow freely through the special perforated cylinder and the added feed and strip solutions, outside and inside the perforation, respectively, to be completely separated.

Jan 1, 1990