Search Documents

By Erdal Unal

In underground mining today, safety and economical aspects demand a better understanding of the rock-mass conditions, particularly for design of underground mine openings excavated in weak and stratified rock mass. The rock mass classification systems, in essence, are empirical approaches utilized during preliminary design stage. These systems have been developed for specific purposes and rock mass types, therefore, direct utilization of the classification systems in their original form, for characterization of complex rock-mass conditions is not always possible. This is probably one of the main reasons why designers continue to originate new systems, or modify and extend the ones already existing. RMR and Q systems, for example, although widely used in mining and tunnelling, can not fully describe the specifications of the weak, stratified and flay bearing rock mass. Consequently, the engineering applications that would be carried out based on original RMR and Q ratings could be inadequate for making design decisions even during the preliminary design stage.

Jan 1, 1990

By John G. Oldsen

Passive cable bolting and active cable trusses have been used in roof support for more than two years Excellent roof control has been experienced by many coal operations. This paper covers the new and innovative developments in cable support systems and their application in mines. Multiple cable bolts, tensioned cable bolts, coal rib wrapping, and other cable applications will be covered.

Jan 1, 1997

By Shosei Serata

Serious floor heave of up to 2.4 m in a 2.4-m high mine entry was eliminated by applying the stress control method of mining, as a last resort, at the No. 5 coal mine of Jim Walter Resources, Inc., in the Black Warrior coal basin near Birmingham. Alabama. Underground observation of the first 3-room entry created using the stress control method is discussed here. The behavior of the test entry, which eliminated the heave problem, is analyzed in relation to similar studies conducted in a salt mine under similar ground conditions by utilizing finite element analysis.

Jan 1, 1984

By P. M. Lin

The problem of abandoned mine land (AML) subsidence is getting more severe because abandoned mine lands which used to be located in the remote areas have been gradually developed into suburbs or even urban areas. Abandoned mine subsidence is also becoming more common than before because the time-dependent effect of exposed underground materials. These materials will deteriorate gradually and cause subsidence as time passes. Subsurface conditions of abandoned mines are seldom known to the public. Mine maps are not always available. If the mine mans are available, their accuracy are very - often questionable. In addition, the most common damages to surface structure and ground surface due to mine subsidence can also be created by other non-mining related geological hazards. These factors make the study of abandoned mine subsidence significantly complicated, tedious, and inconclusive. For instance, the cause, time, and amount of surface subsidence can be predicted with relative accuracy during active mining. However, it will be a considerable challenge to do so on abandoned mine subsidence. If abandoned mine subsidence can be predicted in advance, then the damages can be held to a minimum. However, this prediction technique is not yet well developed. Therefore, remedial measures require more attention. In order to have effective remedial measures, the real cause of the damage should be determined first. This paper describes the approach which was employed for the determination of abandoned mine subsidence. A site investigation was made first. According to the information obtained from the site investigation, a hypothesis was set up. Then the instrumentation was used to prove the hypothesis. By going through the procedures for several cases, a guideline which can be used by the inspectors to inspect abandoned mine subsidence will be established.

Jan 1, 1987

By Kot F. Unrug

The shale response to moisture changes and the major finding of the appropriate research concerning this subject are briefly reported in this paper. Also described are mine ambient atmospheric conditions which are responsible for moisture changes in mines. The need for a quantitative measure of the weathering potential of roof. rock is demonstrated in relation to its influence on safety and the potential for increasing the cost of mine operations. The weatherability test presented in this paper has been developed and used in many mines. It imitates the natural process in a mine by subjecting the rock sample to alternating wet and dry cycles. The natural changes are thus accelerated, but are similar to the natural conditions to which the surrounding excavation rock will be exposed. The measure of the weatherability index is the percentage of the initial sample mass remaining after the test as the largest fragment of the sample. Thus, the index changes, from 100% for rock affected by moisture changes which disintegrates completely, to 0% for rock totally unaffected. In this paper, the apparatus and testing procedures are described. Also presented are examples of test results. with a discussion of the design implication to he considered by mine planners.

Jan 1, 1997

By Kenneth L. Johnson

The effects of underground longwall coal mining on flow in perennial streams within the Pittsburgh seam basin were evaluated. Four streams above four different longwall mines were studied. Overburden depths at the study sites ranged from 500 to 600 feet. At all four locations, premining streamfow measurements were made to establish baseline flow conditions. Measurements were then repeated at each location after the longwall face passed beneath the stream. At one location, in which the longwall panel axis was roughly parallel to the stream, the streamflow was monitored as the longwall face advanced. Measurements at this location showed that temporary flow reduction occurred as the face advanced underneath; however, after the tensile portion of the traveling subsidence profile passed, this effect was lessened. At two of the sites in which the stream was roughly perpendicular to the panel axis, postmining streamfow increased across the panel and decreased over the development headings, such that the net lateral change in streamflow across the fully subsided panel and associated development headings was small compared to the measured flow.

Jan 1, 1997

By David Newman

Coal refuse impoundments and underground mines are frequently sited in close vertical and horizontal proximity in the valleys of the Southern Appalachian coalfield. The steep V-shaped valleys provide the volume necessary for slurry storage against a coarse refuse embankment that is constructed across the valley mouth. The presence of coal outcrops on the valley walls provides economic access to mineable coal seams that may be located under several thousand feet of overburden beneath the adjacent ridges. In some instances where the underground mine precedes the slurry impoundment, the type of mining (partial or complete extraction) and pillar centers were selected without consideration for the potential future use of the valley as an impounding structure. The high standard established for the design and stability analysis of the coarse refuse embankments is clearly illustrated by the absence of an embankment failure in the thirty-one years since Buffalo Creek. However, the recent Martin County slurry spill focused attention on a thorough geotechnical analysis to prevent a connection between the flowable slurry and the mine void. The overburden, roof, pillar, floor, and outcrop barrier stability are examined to quantify the break through potential. The strength and physical properties of the consolidated fine refuse are also important since this material is often the most well-defined and quantifiable barrier separating the slurry and mine void. Because each site is unique, the appropriate analysis ranges from the calculation of roof, pillar, and floor safety factors to detailed numerical modeling of the mine workings and the determination of ground deformation and strains resulting from mine subsidence. The method of refuse disposal may be altered to slurry cells where the accuracy of the mine maps, extent of mining, type of mining (development or retreat) cannot be reliably verified or the break through analysis does not produce an acceptable level of risk. Case histories from the Southern Appalachian coalfield are used to illustrate the application of methodologies to quantify the break through potential of coal refuse impoundments.

Jan 1, 2003

By P. A. Gray

Artificial ground support has developed into a relined science over the past 20 years. From reactive support systems such as timber props and steel supports, to active systems such as roof bolts and cable anchors, ground support technology has now developed efficient systems that work well in many instances. However this paper demonstrates that there is still a long way to go to develop optimum ground support systems. Some conventional rock bolts and cable anchors emphasise their tensile capacity only, without considering other factors such as their shear strength or shear modulus, or if the support member can transfer all of its support capacity to the surrounding rock. Examples are given of the use of ground anchors with high tensile and shear capacity in underground coal mining as well as examples of slope failures in open pits where the cable bolts have remained intact because they have been unable to transfer their full capacity to the surrounding weak rock mass. For underground coal mines, speed of installation is also of primary concern, but it must also have high tensile and shear capacity both in terms of strength and stiffness. Ground support systems of the future must therefore address these problems. An innovative new rock bait is discussed which goes some way towards solving these problems. This new rock bolt is screwed into the rock and thus has a direct mechanical interlock with the rock. Initial field results show that it has an extremely high anchor capacity and can be fully installed in approximately 30 seconds. It has considerable capacity to improve the productivity of the coal mining industry.

Jan 1, 1992

By Neil Styler

This paper presents an analysis of measurements of inter-burden de- formations above six longwall faces. An attempt is made to demonstrate some correlation between the movements at the various sites, and to examine their importance with respect to predicting caving height, disruption of overlying seams, and disruption of aquifers. This analysis demonstrates some significant differences between predicted surface subsidence, and inter-burden deformation. In addition it is shown that the caving height above a longwall face is equal to 8 to 12 times the extraction height, with a zone of fractured rock ex- tending to approximately 50 times the extraction height above the seam.

Jan 1, 1984

By Antoni Kidybinski

Coal mining both with longwall and room-and-pillar method often encounters severe operational difficulties due to had roof conditions. Rooffalls at entry cross-cuts or along the rib line in longwalls as welt as dynamic and excessive loads on supports due to overhanging of strong roof layers in a goab - are well known phenomena to the mine operators. Also, a number of practical examples may be quoted of dramatic improvement of working conditions after changing of coal winning technology or supports type. It is therefore a question to be answered how far we are able to recognize roof strata properties before mining starts and adjust both coal extraction technology and supports of entries to rock stability foreseen. Furthermore, engineering principles and criteria for decision making should be established. In recent years several in situ rock strength and discontinuities detection testing techniques have been developed both indirect (geophysical) and direct thus making possible closer roof-strata examination. In this paper critical roof span criterion is discussed as a basis for selection of proper mining system in terms of desirable stability of mine opening .

Jan 1, 1982

By Yi Luo

Accurate mechanical and geological information of the roof strata is vital for roof bolting design in underground mines. In order to obtain such information in a timely manner, a research has been under way to develop a technology for mapping the roof geology using the drilling parameters acquired during the roof bolting operations. In this paper, a systematic approach has been proposed for determining the rock strengths using the acquired real-time drilling parameters. A computer simulation program based on the mathematic model has been developed to verify the approach and to study its sensitivity. The method has been used to interpret the acquired drilling data.

Jan 1, 2002

By Stephen P. Signer

A method to assist in the evaluation and selection of roof bolts using in situ measurements of roof bolt loading has been developed by researchers of the Spokane Research Center, National Institute of Occupational Safety and Health. Both axial and bending forces are measured by strain gauges at many locations along the length of fully grouted bolts during various stages of mining. This information is then used to ( I) predict bolt loading for variations in bolt spacing, grade, and diameter, (2) calculate the design changes necessary in zones where bending loads are high, and (3) determine if bolt length is adequate. Results from several case studies of full-column bolt loading in coal mine gate roads are used to illustrate the design method. This knowledge will give design engineers a tool for the selection of roof support systems that will improve underground safety by reducing roof bolt failures.

Jan 1, 1997

By J. R. Stoltz

To date, there has been limited formal research dealing with the use of Mobile Roof Supports (MRS) for pillar recovery. This paper, which is a portion of a larger project, presents convergence data from 4 different mine case studies. MULSIM was used to create a numerical model. The resulting information from this model was then compared to the actual measured values. MULSIM was also employed to analyze the industry-accepted pillar/barrier layout for mining underground reserves with the Joy Highwall Mining System. This layout was examined for both a low cover and a high cover extreme,

Jan 1, 1999

By R. D. Lama

The concept of rigid or yielding bolts is discussed based upon support requirements for excavations of equivalent geomechanical behaviour. The concept of equivalent geomechanical behaviour is introduced for comparison purpose where the rock mass properties are varied for a given depth (stress) so that the deformation of the roof without any support remains constant = 300mm. A simple experimental theoretical analysis for a uniform stress field acting on an axi-symmetric excavation is conducted to establish roof bolt requirements under different conditions such as width of a given excavation, time of setting of support etc. Results are presented in graphical forms.

Jan 1, 1992

By Douglas Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because it can result in failures of ground that lead to both injuries and death. Spokane Research Laboratory personnel investigated electromagnetic (EM) emissions in a deep underground mine in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results suggest that (1) there is no increase in the number of EM emissions prior to recorded seismic activity, (2) some EM signals are generated during blasting, (3) interference from mine electrical sources mask seismic-generated EM signals, (4) EM emissions do not give enough warning (compared to seismic monitoring) to permit miners to leave a stope, (5) the distance an EM signal can travel in the rock is between 17.7 and 39.6 m (58 and 130 ft), and (6) current data acquisition systems do not differentiate between EM signals generated from seismic activity and random mine electrical noise. These results preclude monitoring EM emissions as precursors of impending catastrophic ground failure.

Jan 1, 2004

By Adam Mackenzie, Dan Payne, Yass-Marie Rutty

"Historically, the Crinum mine has experienced significant falls of ground when longwall production slowed to prepare for recovery in weak roof areas. These conditions continue through the recovery process and result in both safety concerns and delays. When mine plans and exploration revealed that most of the mine's future longwall recoveries were located in weak roof areas, a decision was made to try pre-driven recovery roads as a solution to the problem. After completing eight pre-driven recovery roads with varying degrees of success and numerous lessons, the Crinum North mine now utilizes a modified Pre-driven Recovery Roadway (PDRR) to improve the longwall take-off process in weak roof areas. During mine development, a standard roadway is driven where the final recovery location of each longwall is planned. After the installation of secondary support, the PDRR is backfilled with a cement-flyash mix to provide support to the roof, and confinement to the ribs and floor of the roadway. The method has been refined over the last four years to provide greater strata stability and improved operational and safety performance compared with conventional take-offs at Crinum, and has resulted in a site record of longwall relocation in 11.5 days (pull mesh to picks in coal). This paper describes the evolution of the PDRRs from Crinum East to Crinum North, including lessons from initial attempts and changes to the secondary support regime, the operational approach during the final stages of retreat, the backfill strategy and plans for the future.INTRODUCTIONThe Crinum mine is the underground component of BHP Billiton Mitsubishi Alliance's (BMA) Gregory Crinum mine, located northeast of Emerald, Queensland (Figure 1).The Crinum mine has a history of roof control problems coming into and during longwall recoveries. Weak roof, combined with the slow mining, which is a consequence of preparing for equipment recovery, pulling mesh (which also creates tip-to-face issues), and the lengthy bolt-up process, often results in loss of immediate roof and subsequent roof falls. In fact, approximately 50% of the first 13 longwall recoveries (which were at depths of 180 to 200m) experienced roof fall delays, the longest of which took four months to mine the last pillar and recover the longwall. This recurring problem prompted the mine to investigate options to reduce or eliminate the problem."

Jan 1, 2016

By Eugene D. Krupa

Mine 33 of Beth Energy has serious and complex roof cutter problems causing delay of the advance rate of both the entry development and longwall face retreat. The cost of maintaining these entries is very high due to the requirement of wry heavy artificial supports. It was suspected that this problem was caused by multiple factors including high in-situ horizontal stresses and weak roof in the problem areas. In order to alleviate the problem, proper design of panel entry and roof reinforcement were considered. This paper presents the results of extensive measurements in experimental panel entries of Mine 33 in order to assess the performance of the designed structure and roof support system during the entry development and longwall retreat. An experimental panel entry has been designed and implemented. The designed parameters were varied seeking for the most ideal parameters which provide stable roadways. Changing these parameters accompanied instrumentation of roof, floor, and pillars. Typical instrumentation, including stress meters, convergence measurement stations, and borehole borescope were utilued. Gnensive monitoring of the behavior of the designed structure and support system led to the development of a complete stress-deformation history of the roadway and an ideal roof reinforcement, support system, which reduced the cost of entry development by less than a third of the previous method.

Jan 1, 1990

By Claude A. Goode

Large quantities of high grade coal exist in thick seams in the United States. Many of these thick seams are too deep to be surface mined and do not lend themselves readily to underground extraction. To develop the new mining technology required to effectively mine thick seams, the Department of Energy has entered into a Cooperative Agreement with Mid- Continent Resources, Inc. to demonstrate the multilift longwall mining technique in a 28 foot-thick seam at their L.S. Wood No. 3 mine near Redatone, Colorado. The seam will be extracted in two lifts, with a 5-foot natural partition of coal left between the upper and lower lifts. Proper selection of face supports is critical to the success of this project. Specifications were defined for the roof supports, and it was concluded that the supports selected must provide full coverage, yield at the legs, and have a 60-inch push- out cantilever that can be set at any position under full load. A Hemscheidt two-leg shield was judged as the best qualified candidate and was selected for the multi-lift trial.

Jan 1, 1981

By Brian Daniels, James Farroni

"Draw rock (small rock that forms/falls when bolting the roof and/or rib) is the cause of numerous injuries annually. These injuries result in lost work hours and low morale. The report below explains how ""Mine Safe Draw Rock Shields"" (Pans) are used in an underground operation. This report will chronicle the application of these pans in a Southern West Virginia coal mine along with testing data that measures their effectiveness. Since the introduction of these pans in 2002 the amount of reportable accidents relating to draw rock has decreased by 80%. The report below reinforces that perimeter contact is critical to the performance of these pans. In addition the strength of these products at the perimeter will determine their effectiveness. The results of the testing data outlined in this paper, along with the physical records at the study mine, confirm that the use of pans has significantly reduced draw rock falls at this facility.BACKGROUNDSupplemental support is defined as ground control that is used in addition to required support in an underground mine. Some examples of supplemental support are:• Pans• Mesh/Geogrid• Mats• Half Headers• Boards• ChannelA typical roof condition that warrants the use of pans is when loose small rock is dislodged while bolting. If the top is very scaly (loose, thin rock) additional supplemental support can be used in conjunction with pans such as mesh or geogrid (See Figure 1). Pans will provide protection where used and approximately 12 in (250 mm) out from perimeter. This is achieved by contact with a surface which will put scale in tension up to 12 in (250 mm) from perimeter of pan.INTRODUCTIONThe ease of applying a roof support system is critical to effectively operating a deep mine. Figure 2 shows how a pan is installed in conjunction with a roof bolt and bearing plate. The Mine Safety and Health Administration (MSHA) requires that supplemental support cannot decrease the performance of required support. The goal of using all supplemental support is to provide additional safety for the miner which equates to increased productivity.The ability of skin control products to contact a surface is the single most critical characteristic (Figure 3 and Figure 4). If the material does not contact the surface it cannot be effective. Therefore, the flexibility, design and proper installation of the products are critical in determining their effectiveness. Figure 5 shows the proper installation of the roof pan.To reiterate, all skin control must be applied in conjunction with a roof bolt and ASTM approved bearing plate as shown in Figure 4."

Jan 1, 2010

By John Stankus

Seam interaction in multiple seam mining has significant effect on entry stability. The remaining pillar in an old working usually creates a high stress concentration zone while the gob creates a stress release zone. A good panel layout should take advantage of the stress release effect created by old workings. This paper presents two case studies of multiple seam mining. The Jennmar Finite Element Analysis System (JFEA) is utilized to analyze the seam interaction effect and identify the mess concentration and relief zones Panel layouts are designed bad on the results of the finite element analysis Appropriate roof support system are also designed for different seam interaction areas.

Jan 1, 1999