Search Documents

By Michael Amick

Over the last few years as the coal industry has seen an increase in the price of coal, a renewed interest in the additional mining of pre-law highwall sites has occurred. Much premium coal and property remains behind these pre-law highwalls but access to mining is limited because prior mining used auger machines to remove coal from under the highwall. Older augers seldom reached more than 200 feet and often no more than 100 feet but this zone of auger holes destabilizes the highwall to where additional mining is often unsafe. If the reserve is large enough, the highwall can be stabilized with common flyash and cement grouts to form a face-up for an underground mine but this expensive method is usually not practical for continuous use with a highwall mining machine. It is estimated there are hundreds of miles of highwall riddled with auger holes where the coal reserve available is ill-suited for deep mining for a variety of reasons. However, these same properties are ideal for additional mining with state-of-the-art highwall mining machines that have a reach up to 1200 feet, except to the relatively thin auger mined de-stabilized zone. The renewed interest in highwall mining these properties has driven research into finding an economical way to stabilize the highwall so the highwall mining machine can recover additional coal. This research discovered and fine-tuned a process that is economical and is successfully supporting the highwall at a highwall mining operation. This paper discusses the research involved in determining the strengths need, the methodology used to place any grouts, the effect on mining plans and the increased recoveries. ARMPS-HWM is used extensively in this research. The failure of the highwall, when not grouting, and the success, when grouting using the new materials and equipment utilized, confirmed the ARMPS-HWM method.

Jan 1, 2007

By Richard E. Gray

Subsidence due to coal mining is poorly understood by non-specialists. This has led to numerous misconceptions and myths based on limited observations and lack of knowledge. The three most common are: 1. Mine maps are inaccurate. 2. Deep mines are not a problem. 3. If no subsidence has occurred for many years after mining, there is no risk of future subsidence. Maps are important during mining and most are carefully prepared. Future use to evaluate conditions at mine level often includes drilling to confirm what the map shows. Usually, little or no effort is made to tie the surface survey of the property to the mine survey, to conduct a well designed drilling program to confirm the mine map, or to drill test borings vertically. When a mine entry is encountered rather than a coal pillar, or vice versa, and conditions at mine level appear different than anticipated, the first reaction is the mine map is inaccurate. The idea of a safe depth from subsidence is often based on the false premise that mining results in sufficient breakup of the overlying rock strata that bulking compensates for the coal extracted. The safe depth idea first appeared in the literature about 1880 and remained prevalent well into this century. Sadly, it is still encountered. The modern understanding of fragmentation of the immediate mine roof with the overlying beds sagging down on the broken roof rock was first described in 1900. With full extraction mining, either longwall or retreat room and pillar, surface subsidence occurs regardless of the depth of the mine. Subsidence over longwall mines at depths of 2000 feet can be 90 percent of the mined seam thickness. Numerous studies of undermined sites conclude that mining occurred many years ago and since no subsidence has occurred, there is no risk of future movement. This is true if sufficient coal pillars have been left to support the overlying strata. However, every year subsidence occurs over mines that have been closed for 100 years or more. In a study of subsidence incidents over the Pittsburgh Coal, the senior authors found that 50 percent of the incidents occurred above mines that had been closed for at least 50 years and 10 percent over mines closed for at least 80 years.

Jan 1, 1996

By Takashi Sasaoka

The PT. Adaro Coal Mine targeted in this research is located in South Kalimantan, Indonesia. The coal production of this mine is increasing year, with about 35 M tons of coal produced in 2006. This mine faces many ground control problems, especially instability of the footwall. Large-scale landslides occur often in the footwall; this may be because of weak rock and the effect of footwall rock weathering. Hence, prompt measures must be developed and followed in order to preserve the stability of the footwall and make this mine safe. Additionally, the final pit design is now being reconsidered because of the increasing demand for and high price of coal. With these issues in mind, this paper describes a solution for improving the stability of the footwall and discusses the final pit design based on the results of an on-site investigation and numerical analysis.

Jan 1, 2008

By Keith A. Heasley

The LaModel program has been used successfully in the United States for many years to design pillars to ensure global stability of pillar recovery operations. However, the recent Crandall Canyon Mine collapse showed that further research was required to improve the design of pillar recovery under deep cover. Toward this end, a new calibration procedure was implemented in LaModel. This calibration procedure prescribes techniques for calibrating the critical LaModel input parameters based on empirical abutment loading and pillar strength, as utilized in the time-tested ALPS and ARMPS programs. The calibration procedure is intended to help guide a novice modeler in choosing calibrated input parameters that produce a standard model that fits within the verification database. However, the rigid parameter specification incorporated in the calibration procedure also removes most of the flexibility in LaModel for specific calibration to the unique conditions at a given mine site. In this paper, a number of the LaModel input parameters are varied outside the bounds of the suggested calibration and the effects on the model results are analyzed. Ultimately, it is shown how the LaModel user might vary certain input parameters to adjust the model to site-specific conditions, while still maintaining the general accuracy and philosophy of the recommended calibration.

Jan 1, 2012

By Hamid Maleki

Roof falls are one of the leading ground control problems that adversely influence productivity and worker safety in underground mines, construction sites, and nuclear waste repositories. To control roof stability problems, the operator needs to have practical methods for measuring changes in strata conditions and criteria for defining the timing of secondary support installation. The objective of this study was to develop measurement techniques and criteria for assessing roof conditions at the mining face. An integrated rock deformation and tomographic imaging method was developed and applied at two sites in a western U.S. trona mine. It was shown that rock damage occurred at a deformation of 30 to 60 mm (1.2 to 2.4 in) (2 to 4 pct strain) and was associated with a significant (16 pct) reduction in wave velocity. Thus, supplementary support may be installed when there is a measured change in wave velocity of at least 16 pct. Tomographic measurements can be obtained in rocks rapidly, thus providing a powerful tool for analyzing growth of failure and for installing supplementary support systems in a timely manner.

Jan 1, 1996

By D. S. Choi

This paper describes an improved source location technique for microseismic events related to coal mining. A system of non- linear distance equations is solved with the use of the Newton-Raphson method. This computational method is- advantageous when the number of geophones is limited. In addition, this paper includes the results of the analysis of data from several instruments which characterize both mine seismicity and environmental noise such as vehicle traffic. Analysis of the mine seismicity has contributed to a better understanding of caving above a longwall gob and of what constitutes stable ground conditions.

Jan 1, 1990

By Holger Witthaus

There is more than a century of experience in multiple seam mining in Germany. In several mines up to 20 seams had been excavated within the last decades. Due to the nature of the deposit and the history of technical development the older panels cause a complex stress distribution for the lower seams and the current longwalls in descending order of mining. The depth of the longwalls reaches up to 4000 ft. This causes a maximum vertical stress that reaches between 30 and appr. 60 MPa. To handle these conditions several support systems are applied for roadway heading. A central knowledge management system for ground control is used for design and dimensioning of support within the DSK. This paper gives an overview to the nature of German multiple seam mining and the solutions in matters of panel layout and support design. It describes the full lifecycle for roadways in the seam starting with the geological and geotechnical evaluation, the basics of roadway deformation in great depth, the development of planning tools and standards for German coal mines, the range of alternative of support systems and roadheading techniques, as well as the reinforcement measures and the processing of support at the T-junction of the face entry. This paper uses exemplary descriptions that are consolidated in a specialized reference book ?Gebirgsbeherrschung von Flözstrecken? ? ?Ground Control in Roadways? which summarizes the standards of ground control based on the development of the past 25 years in German coal mines.

Jan 1, 2007

By Khamis Y. Haramy

This paper summarizes ground control studies of longwall panel entry systems in two Western U.S. coal mines. Presented are comparisons of in situ pressure change measurements and assessments of chain pillar and entry behavior under a wide range of cover. Results indicate that no one entry system design is universally applicable, and that site-specific factors need to be considered for panel entry design. Relationships between overburden depth, face advance, and magnitude and location of the forward abutment are discussed for western operations. In addition, analysis indicates that use of yield pillars may reduce or eliminate some stress-related problems that plague longwall panel entry design.

Jan 1, 1989

By Luis E. Vallejo

The strength measured by the uniaxial compression test is a parameter that is widely used for the engineering classification of rocks. Sedimentary rocks such as shales, however, are difficult to evaluate by uniaxial compression tatting because the rocks slake during the preparation of the standard samples required for the tests. Indirect methods such as the point load test have been proposed to determine the unconfined compressive strength of shales and other soft rocks. It is current practice to use 24 as the conversion factor between the point load strength, Is, and the unconfined compressive strength, sf (sf = 24 Is). The present study investigated index-to-strength conversion factors for shales and sandstones obtained from surface coal mining sites in the Appalachian region. Regression analyses indicate that a conversion factor of 12.5 best correlated the strengths obtained from the point load and unconfined compression tarts in the case of shales. For the sandstones, a value of 17.4 best correlated the strengths.

Jan 1, 1989

By V. D. Jalevsky

A new methodology of an experimental-analytical approach has been developed. It is used in building an information geomechanic monitoring system for the modeling of geomechanic processes during coal seam working. The approach synthesizes experimental (in-situ) measurements of rock pressure manifestation in separate points, methods of numerical modeling of processes on rock boundaries with coal, and a seam analytical calculation of rock mass in a spatial strained state. One of the realizations of this approach is the developed theory and calculation method of adjoining rock surface shift (overhang) formation during underground working of sheet deposits and of rock mass geomechanic state determination. There are description algorithms of cavity configurations with broken lengths of faces during underground working of useful mineral sheet deposits. These algorithms have been used in computer modeling of formations of adjoining rock surface overhangs and abutment pressure upon rock mass in the area of coal faces with irrectilinear longwalls. Peculiarities of surfaces shifts and stress allocation are established for different face schemes. The use of theory and methods alloww working out techniques of automatic control to receive processing algorithms of RPM measurement results and calculate geomechanic situations within panels in the process of planning and development as well as during mining, i.e., to carry out long-term prediction, in-line control, and short-term prediction of rock pressure manifestations.

Jan 1, 1996

By S. Yamashita

Recently in Japan, unexpected degradation (surface subsidence) at old underground quarry sites, such as 'Ohya-Ishi' (pumice tuff) pit field has often been occurred. At these quarry sites, the excavation was started 20 or 30 years ago with mechanical chain cutter and the Room and Pillar method, and stopped 7 or more years ago. Therefore, a reliable method has been required for an estimation of long term mechanical properties of the rock and for an observation of a stability of rock-pillars or structures. In this study, creep tests under uniaxial compressive load were carried out on the 'Ohya-Ishi', with the aim of estimating the long term stability of the rock. From these results, a creep mechanism of the rock was discussed using the failure mechanism hypothesis proposed by Bieniawski and by others. On this basis, critical time to failure was predicted by the relationship between the logarithm of life time and stress ratio of the sustained axial creep load. Additionally, outline of the monitoring system of AE/MS activity in the field, which have set by the Ohya Aria Consolidate Public Corporation and the others to predict or to prevent the degradation of those residual pillars, is to be reported. Key words : Ohya-ishi, Pumice tuff, Mine pillar, Long term stability, Creep, Critical time

Jan 1, 1996

By Keith A. Heasley

Numerous different instruments and techniques have been developed for the purpose of measuring rock stress and stress changes around excavations. The interpretation of the output from many of these instruments has often been problematic. This paper covers the research performed in attempting to analyze one particular stress measuring instrument called the Borehole Platened Flatjack (BPF) . The approach used in this analysis was to combine the analytical solution for the displacements around a borehole and the analytical solution for the bore- hole-platen interaction with the empirical stiffness behavior of the flatjack. The resulting model of the BPF response was then verified using measured laboratory data with very good results. In addition, techniques for applying the method to the field are briefly discussed. The major accomplishments of this comprehensive modeling and testing program are; 1) the establishment of the critical installation and site parameters of the hydraulic pressure cell and 2) the development of a systematic procedure for calibrating the cell based on the given values of these critical parameters.

Jan 1, 1989

By S. E. Phillipson

Underground mine mapping is a critical component of understanding the controls on ground instability. Many relatively localized examples of ground failure are associated with geologic features, such as faults, joints, compaction zones, or sedimentological transition zones. In contrast, long-running, directional roof falls are associated with regionally directed horizontal stress fields, which are induced by tectonic plate interactions in the earth?s crust. When stress-related features are distinguished from geological features, underground mapping can be an effective method for inferring the direction of horizontal stress at individual mines. Comparisons with data compiled in the World Stress Map confirm that underground mapping can be a valid method for determining the orientation of maximum principal horizontal stress at a variety of scales, ranging from individual mines to an entire mining district or coal basin. Comparisons are presented between the maximum horizontal stress directions inferred by MSHA?s Roof Control Division through underground mapping and the azimuths of maximum horizontal stress in the World Stress Map database for North America?s Pennsylvanian-aged Appalachian, Illinois, Black Warrior, and Arkoma Basin coal fields. The comparison indicates that azimuths are similar for both data sets, even where variations in the direction of horizontal stress are present. It is interpreted that inconsistencies in direction are attributable to near-surface affects such as deeply incised stream valleys, or to fault zones that represent heterogeneities in the crust.

Jan 1, 2009

By V. Bondarenko

The forecasting of floating earth inrush into the working is to a great extent connected with the investigation of the rock mass stressed-deformed state around the working. The aim of such investigations is to estimate the carrier ability of the protective layer (which is stabilized by the physico-chemical mode of fixing) and to determine it's thickness, which is to be sufficient to present the floating earth inrush into the working. We consider the protective layer to have exhausted it's carrier ability if the rocks of this layer reached the overlimit phase of deformation and it's greater part (section), which adjoins the working. is destroyed up to the limit of the remaining strength. So, the aim of investigations is to determine the size of the rocks inelastic deformation zone in the roof of the working. It is necessary to take into account the presence of water saturated seam in the roof and the overlimit characteristics of the rocks, their ability to lower the carrier capacity up to the level of the remaining strength.

Jan 1, 1996

By F. N. Voskoboyev

The suggested new method for control of geomechanical state of undermined rock mass ensures, as a safety measure for the earth surface protection, the decrease of deformations by 2,5 - 10 times in mining the single seam, and by 1,5 - 5 times - in mining bed series, i. e. approximately within the seam ranges as in the application of full packing with various compressive properties or partial extraction of resources over the area with different coefficients of extraction. It should be noted that this new method has the following advantages o\w rhr. conventional methods: a) the decrease of the packing area and packing works volume by 2 - 4 fold including the operating and productive expenses; b) the elimination of mineral losses due to the increase of extraction coefficient up to 100 5%; c) rock utilization from workings drivage by its placing in the mined - out space. Perspective field of application of this method: disconservation of mineral resources in the left protective pillars of various designation.

Jan 1, 1996

By S. J. Jung

A fundamental study of fragment size distribution and characteristics of fracture pattern is presented for the dynamic penetration of a conical bit into coal block. In this paper, damaged zones during crater formation and fragment size distribution were studied. Bit with a sharper tip angle and a smooth body configuration performed better penetration. Results suggest that in coal cutting the trend should be toward the face cleat direction using a sharper angled tip bits which consumes less energy for an optimum range of penetration depths, thus attaining maximum cutting efficiency and reducing fine fragments.

Jan 1, 1989

By A. W. Khair

This paper presents an analysis of fracture depth and intensity due to subsidence over the longwall panel. Sonic reflection techniques were utilized to determine fracture depth, and a variation of p-wave velocity was used as an indication of the fracture intensity. Instrumentation has been tested for consistency and accuracy first in the laboratory using small scale models, then applied in the field in two mine sites with different mining geometry and geologic conditions. A new sonic viewer was utilized for sonic velocity measurements. Regular hammering method was on acoustic source. The results were concurrent with monitored horizontal strain profiles and measured open fractures over the longwall panels.

Jan 1, 1989

By Peter Altounyan

The rate of decay of the energy from a hammer blow to a coal mine roof is related to the size and nature of the contacts between the rock being struck and its surroundings The use of this principle as a basis for testing roof condition in South African coal mines has been investigated under a SIMRAC funded project, with the objective of reducing the number of roof falls. ( I ) A prototype instrument having a simple numeric display related to the energy decay rate (the Acoustic Energy Meter) was constructed and used to carry out surveys at mines covering the range of coal mine roof geology and condition. The equipment was simple to use and provided excellent discrimination between visually intact roof and less stable conditions, once the normal/abnormal threshold had been established for a given site. Areas of potential roof failure were identified close to roof slips and igneous dykes, and confirmed in areas of visible deterioration. Directional stress effects on roof condition were also identified at some sites, with consistent differences in readings obtained depending on the direction of drivage. Repeat surveys also indicated areas where roof conditions were deteriorating with time. Based on the success of the prototype, a hand held version of the instrument. has been developed to a specification from Anglo Coal. This incorporates a simple 'traffic light' green / amber/ red display, making the device suitable for routine use by mine operatives This version is now undergoing trials at an Anglo Coal mine. It is concluded that the Acoustic Energy Meter shows great potential as a test instrument providing output which relates to the stability of the immediate roof.

Jan 1, 2000

By Gang Chen

Conventional methods designate a factor of safety, a deterministic number, to indicate the stability of a mine excavation. However, this deterministic description of excavation stability is frequently insufficient or inaccurate and, sometimes, misleading. Employing the probabilistic analysis to determine the likelihood of mine excavation failures will lead to a better understanding of ground control problems and result in more rigorous designs of the excavations. Based on the theory of probability, two approaches are taken in this study for the probabilistic analysis of excavation stability. The first one utilizes direct integrations for the estimation of failure probabilities of mine excavations. Due to the complexity of the integration, this approach can only be applied to solve relatively simple problems. In order to overcome the limitation of the direct integration method, the second approach employs the first-order second-moment approximation of the failure probabilities for more complex ground control problems. The probabilistic analysis offers a deeper insight into the uncertainty associated with the stability of mine excavations. The study indicates that the distributions of parameter values play a significant role in the mine excavation stability, which can not be disclosed by the conventional methods of stability analysis. Greater dispersiveness of the parameter values will lead to a different probability of failure, although the factor of safety estimated by conventional methods stays the same if the mean values of the parameters are constant. By taking consideration of the probabilistic distributions of the parameters, the probability model can provide more reliable designs of mine excavations.

Jan 1, 1996

By Ian Misich

Surface subsidence resulting from "total extraction" of coal in the Collie Basin first occured in 1987 when Western Collieries Ltd trialed the Wongawilli mining method. Because very little quantitative subsidence data existed for the weak, Permian sediments, a research program was set up prior to the extraction of the first panel. The objective of the study was to be able to predict subsidence characteristics and effects prior to mining future total extraction panels. Attempts at predicting subsidence began using existing subsidence models from other coal mining regions, however, as more site information became available, it became clear that it was necessary to develop a separate, site specific predictive model for the Collie Coal Basin. Analysis of extensive field monitoring data for both surface and subsurface subsidence has produced a series of empirical models which can predict the shape of surface subsidence troughs and corresponding tills, and strains for rectangular panels and describe the sequences of ground movement from the mine root through to the ground surface. The fact that both subsurface and surface subsidence characteristics have tied in well, gives greater confidence for predictions made from these models

Jan 1, 1992