Search Documents

By Donovan J. Benton

Photogrammetric methods are advancing rapidly and show considerable promise as a ground control research tool. The ability to quickly capture three-dimensional geometry, especially changes in geometry, in underground and laboratory settings is a significant advance from point distance measurements. Photogrammetry is being applied in both of these settings as part of the NIOSH ground control research. This paper describes these applications and the equipment and software being employed. It also describes tests conducted to quantify the accuracy of these systems. Accuracy varied with system specifics and procedures. A factory-calibrated camera produced results within 1/32 of an inch, plus 0.04%. A user-calibrated camera was found to be less accurate, at 1/20 of an inch, plus 0.24%. These calibrations demonstrate that photo grammetry can produce research quality measurements in laboratory and mine settings.

Jan 1, 2014

By Gennaro G. Marino

As part of the development of a shopping center in West Virginia, a significant bench had to be cut into a mountainside that was over 700 ft. high. As a result, a steeply stepped, over 400-ft.- high wall was created. The high wall exposed old abandoned room-and-pillar coal workings at the toe of the cut. Because of exposure to the elements, the mine openings began to severely deteriorate with significant potential of undermining of the rock cut face and causing a large rock fall(s). Exacerbating this wall problem was a set of fairly planar sub-parallel and sub-vertical joints creating, in essence, thin rock slabs. Also present were stress relief fractures that were observed in the exposed pillars. Given the proximity of the project building to this high rock face, mitigation of the rock fall potential was deemed necessary. In order to prevent continued damage and deterioration of these exposed mine entries, the rubblized openings were filled with bulkhead grout and pressure injected with grout. The total amount of grout installed in these openings was about 3,945 CY. Also, a rock drape was attached to the entire face to mitigate small rock falls from natural causes. There also existed another level of mining below the ground surface and under an existing building at a depth of about 160 ft. Under a portion of the building, the pillars in these old works were second mined, and the building seemed to have been already affected by limited subsidence above this area. Also, calculated pillar safety factors in this high extraction section of the mine were too low. Consequently, these old works were stabilized by saturation grouting. An indication of overall roof distress was the significant fracturing encountered in the bedrock overburden during the drilling of the injection holes and the volume of grout placed in these holes. The total grout installed in the high extraction section of the lower mine was about 6,660 CY. This paper describes the investigation and the grouting techniques employed at the rock cut face and under the existing building to mitigate continued damage to avoid future subsidence problems at the face and the building premises.

Jan 1, 2013

By Anthony T. Iannacchione

This study, funded by the Appalachian Research Initiative for Environmental Science (ARIES), examines how mine layout, mining method, and geology interacted to allow water from the Grove No.1 mine pool to discharge into local surface waters. Federal and State regulations prohibit the discharge of acid or iron-producing waters from underground coal mines. Mining companies design barriers around their operations to prevent mine waters from discharging to the surface. The Grove No.1 represents one mine where these designs proved inadequate. Unique geologic conditions at the Grove No.1 mine pool, combined with retreat room-and-pillar mining, contributed to a discharge that required passive water treatment.

Jan 1, 2013

By Ihsan Berk Tulu, Keith A. Heasley, Chris Mark

"The Analysis of Retreat l\.fining Pillar Stability (ARJ\1PS) and the Lal\.fodel programs have been used successfully in the U.S. for designing safe pillar recovery operations for many years. However, the recent Crandall Canyon l\.fine collapse showed that further research is required to improve the pillar design for recovery under deep cover. To this end, the National Institute for Occupational Safety and Health (NIOSH) and the West Virginia University (WVU) l\.fining Engineering Department have been working together to improve both the ARJ\1PS and the Lal\.fodel programs.This paper compares and analyzes the overburden loads calculated by ARJ\1PS 2002, the new ARJ\1PS 2010, and the Lal\.fodel program with regard to the retreat pillar line, the gob, and the barrier pillars. The analysis shows a number of distinct differences between the ARJ\1PS and Lal\.fodel loading distributions. Ultimately, the programs, with their distinctive load distributions, are used to analyze a database of 52 deep cover pillar retreat case studies, and the ability of each program to discriminate between successful and unsuccessful retreat pillar plans is evaluated.INTRODUCTIONThe Analysis of Retreat l\.fining Pillar Stability (ARJ\.f PS) and the Lal\.fodel programs have been used successfully in the U.S. for designing safe pillar recovery operations for many years. However, the recent Crandall Canyon l\.fine collapse showed that further research is required to improve the pillar design for recovery under deep cover.Pillar recovery accounts for less than 10% of the coal produced from underground coal mines; however, in the period between 1989 and 1996, it accounted for more than 25% of all ground fatalities (l\.fark et al., 2003). In the past 15 years, the safety of retreat mining operations has greatly improved. l\.fark (2009) explains three steps promoted by l\1SHA and NIOSH for safer pillar recovery:1) Global stability through proper pillar design2) Local stability through proper roof support3) Worker safety through proper section managementThe ARJ\1PS and Lal\.fodel (Heasley, 1998) programs have been playing an important role in guiding mine operators in designing pillars to ensure the global stability of a retreat panel."

Jan 1, 2010

By Fangtian Wang

The fully mechanized longwall mining was employed in a shallow coal seam that was under the gobs of room and pillar mining and overlain by thin bedrock and thick loose sands. Operational practices have demonstrated that severe accidents would occur including roof structure instability, roof steps, damages of shield supports, and face bumps triggered by the large area roof weighting, resulting in serious threats to the safety of underground miners and equipment. This paper uses Shigetai Mine, located in the Ordos area, Inner Mongolia, as the study site. It fully considers the geological conditions of 3-1-2 coal seam and employs theoretical analysis, 3DEC numerical simulation, and field measurements to analyze the overlying strata movement for the shallow seams under an abandoned room and pillar mine without pillar extraction. The research results serve as an excellent guide to mining in similar geological and mining conditions.

Jan 1, 2014

By Xuexin Ding, Weijie Wei, Jinwang Zhang, Yi Chen, Shengli Yang

"Many ultra-thick coal seams exist in Xinjiang and the northern part of the Inner Mongolia. These coal seams are more than 30-40m thick. This kind of the thick coal seam is too difficult to extract in one slice, so the top-coal caving longwall mining method was designed for this purpose. In order to study the movement characteristics of the overburden strata and the development of the ""three zones"" in ultra-thick coal seams, the physical and numerical simulations were carried out based on the in-site condition of Baiyinhua coal mine. The result shows that, when extracting the upper part of the l 5m thick coal seams, the first weighting interval was 50-58m and the periodic weighting interval was I 8-20m. The caving zone, fractured zone and bending and sinking zone were 38m, 92m, and 50m respectively in height. The fractured zone height increased with the advancing distance of the face, but in some localities, a ladder-like distribution due to the periodic weighting existed. When extracting the lower part of the 25m thick coal seams, the roof was extremely broken and the collapse range of overlying strata continued to increase in irregular form.INTRODUCTIONThe thick coal seams occupy 44 percent of coal reserves in China and account for 45 percent of the gross domestic coal production. There are three main methods for extracting the thick coal seams: sublevel mining, large height mining, and longwall top-coal caving (LTCC) (Wang, 2009). Due to the rapid development of LTCC in the past two decades, it has become the most extensively used mining method. It possesses the advantages of high-production, high-efficiency, low development ratio, and low-cost (Yang, Zhang, Chen, and Zhengyang, 2016; Wang and Zhang, 2015). Baiyinhua coal mine's coal reserves are full of uniformly distributed thick coal seams, with the minable thickness of the main coal seam between 25 to 40m, i.e. the main coal seam is an ultra-thick coal seam. Sublevel longwall top-coal caving (SLTCC) which is an efficient method for extracting the ultrathick coal seams has led to multiple disturbances Xie, Chen, and Wang, 1999; Singh and Singh, 1999; Xie, Chang, and Yang, 2009. Therefore, using the case of Baiyinhua coal mine, the movement features of overburden strata and development characteristics of the three zones in ultra-thick coal seams were studied by physical and numerical simulations (Qian, et al, 2003; Qian, 1994)."

Jan 1, 2016

By I. Sedat Buyuksagis, Jamal Rostami, Ali Naeimipour

"Improving the safety of underground openings and optimizing ground support systems requires reliable ground characterization. This includes understanding the joints, discontinuities, and rock strength. Joint information can be obtained from borehole cameras, but measuring in-situ rock strength is very difficult. Use of borehole probes can be an ideal and efficient way to meet this requirement. This paper discusses the development of the Rock Strength Borehole Probe (RSBP) and presents the preliminary laboratory/field test. This device can be an accurate, flexible, quick, non-disruptive, and cost-effective alternative to estimate the rock strength inside boreholes in underground mines and tunnels. In addition, the scratch testing procedure in the laboratory by means of a newly developed miniature linear cutting machine is explained. Based on the results of these tests, two equations are developed to estimate the uniaxial compressive strength (UCS) and Brazilian tensile strength (BTS) of the sedimentary/metamorphic rocks. These equations, are based on testing 27 different sedimentary, igneous, and metamorphic rocks by full-scale scratch tests, including the cutting tests by a miniature disc. The results show a good correlation between the normal force and the compressive strength of sedimentary rock if the depth of the scratch is known. No significant correlation was observed for igneous rocks, due to the impacts of grain size.INTRODUCTIONEstimated rock mass properties are essential input for geomechanical studies and stability analysis for any structure constructed in or with rock. The availability of geological information is the crucial component of rock mass classification. One of the important parameters in evaluating rock mass properties is the intact rock strength. This parameter is usually measured by testing the core samples, obtained from exploration boreholes. These samples are subsequently tested in geomechanics laboratories. The test results offer limited information about the rock at the few boring locations despite all the efforts and costs. In addition, these results may not necessarily be representative of the behavior of the rock in the field as the test cannot provide the insitu condition of the ground."

Jan 1, 2016

By Zhang Hongzhen

The fast convergence of boundary is a major problem of probability integral method, especially for the prediction of mining under thick alluvium, abandoned mine goaf, etc. To solve this problem and improve the accuracy of probability integral method, a modified model is constructed for surface movement and deformation based on theoretical analysis. In which, three weighted values i.e. 1, -1/t1, 1/t2 are set for the mining movement and deformation of three different major influence radius i.e. r1, R1, R2, respectively, then the parameters are selected as following: (1) Parameters are inversed based on the observation data, in which the subsidence factor q, deviation of inflection point s, displacement factor b are considered as generic parameters, the tangent of major influence angle tanß is modified as tanß2, that is the major influence radius r is modified as r2. (2) Inversion parameters of tangent of major influenceangle tanß or major influence radius r, based on the observation station edge data which beyond major influenc eradius distance from work-face mining boundary. The inversed tanß and r will be used as tangent of major influence angle tanß1 and major influence radius r1, respectively. (3) Other relevant parameters i.e. t1, t2, R1, R2, are calculated with the algorithm of this paper. A comparison experiment between the traditional and modified models has been conducted using the observation data from a observation station, the results show that in its central area, 58.6 percent of observation points accuracy is improved and 36.6 percent is decreased, while in its edge area, 61.5 percent is improved and 15.4 percent is decreased, totally, 68.6 percent is improved and 30 percent is decreased. Therefore, we can draw the conclusion that our modified model can improve the prediction predication accuracy, in particular, the boundary region.

Jan 1, 2014

By Liu Xiao, Lin Xiaoying, Ma Geng, Tao Yunqi

"The soft coal in China has several issues, low permeability, high gas content and prone to gas outburst, making it difficult to drill and improve its permeability. Using the rock mass loading test, the relationship of stress-strain-permeability-time of sandstone was investigated. The fracture network that communicates with coal seams to provide the pathways for gas migration can be established by drilling, hydraulic fracturing or loose blasting in the roof and floor about 5m from coal seams top and bottom. The gas migration can be summed up as ""desorption-diffusion-two levels of seepage"" for gas drainage of the quasi-protection-layer in hard coal seams, and ""desorption-two levels of diffusion-seepage"" in soft coal seams. In the quasi-protection-layer, different gas drainage techniques were used during different stages of mining. Gas drainage of the quasi-protection-layers was demonstrated at Hebi Zhongtai Mining Co., Ltd. The results showed that the technique promotes the gas seepage flow, and improves the efficiency of drainage. The influence zone of the quasi-protection-layer was 1601 m2 and the average amount of gas drainage was 328m3/d, with the maximum being 661m3/d. INTRODUCTIONGas is one of the main factors that cause disasters and influence safety production in underground coal mines (SACMS, 2009). The coal-bearing formations in China have been subjected to multiphase tectonic stress field during the period of geological evolution. Coal body was often crushed into fragmented coals and mylonitic coals under the tectonic stresses (Su and Lin, 2009). The gas permeability of coal is generally poor. So in underground, drilling and hydro-fracturing technology have been used to improve the permeability of coal, such as intensive drilling, hydraulic punching, hydraulic cutting, hydraulic extrusion and deep hole blasting. But the gas drainage rate was low, only 23% (Liu, Li, and Li, 2006; Li and Wei, 2006; Henan Polytechnic University, 2008; Ma, et al., 2014; Lin and Wu, 2009; Zhou, et al., 2011) that was much lower than the rates achieved in the main coal-producing countries such as America and Australia whose average rate of gas drainage was 50%. The protection layer mining technology has been used widely as an effective technique to improve the permeability of coal in the mining of multiple coal seams (Cheng and Yu, 2003; Diaz and Gonzalez, 2007; Karacan, et al., 2007; Palchik, 2003; Latham, et al., 2013; Yuan, et al., 2013; Shi and Liu, 2007; Wang, et al., 2008, Guo, et al., 2015; Lu, et al., 2015; Slazak, Obracaj, and Swolkien, 2014 ). In the single low permeability coal seam, there is no protection layer. This kind of coal seam has low permeability, high gas content, soft coal body, and is prone to serious gas outbursts. During drilling, the holes very often spray, collapse, stuck and wedged the drilling tool. The hole length drilled is difficult to reach the required minimum, the service life of holes for gas drainage is short, the construction cost is high, and the holes are difficult to maintain. The gas drainage efficiency of single low permeability coal seam, especially soft coal seams, cannot be improved even though hydro-fracture technology has been implemented, because its permeability is not improved."

Jan 1, 2016

By Jiachen Wang

China is the largest coal producing country in the world. Coal is widely distributed in China and thus the mining conditions are complex and diverse. This paper summarizes the important achievements in the last 20 years in various mining methods including the extra thick seam with large mining height top coal caving, the thick seam with large mining height and top coal caving mining, the steep seam with top coal caving and fully-mechanized mining, the thin seam automated mining, and the backfill mining. At the same time, the rapid advance in the development of mining machinery and manufacturing has also contributed to the advancement of coal mining technology and the great improvement of coal mine safety. The future direction of China?s coal mining is to further improve mine safety as to improve the coal recovery rate, promote the pillar less mining technology, develop high-efficiency backfilling technology, develop steep seam high-efficiency mining technology for seams less than 10m thick, and high recovery mining techniques for extra thick seams, improve the reliability of mining equipment, and strengthen the protection and restoration of surface environments and water resources.

Jan 1, 2014

By Baogui Yang, Jie Yang, Anthony Iannacchione

"The cemented coal gangue-fly ash backfill technique (CGFB) has commonly been used to control subsidence damage caused by underground coal mining. This paper discusses the CGFB backfilling process used at the Xin-Yang coal mine, Shanxi Province, China. A general description of the components of the CGFB are provided. The reaction of the strata to the backfilling process is simulated with a scaled physical model based on the Xin-Yang conditions and verified with subsidence points on the surface. With the help of the cemented filling materials, the CGFB produces only a slight bend to the overburden roof strata over the longwall panel. Physical models were constructed at the China University of Mining and Technology, Beijing, to simulate actual conditions. The modeling results show minor fracture distribution in the overlying strata and lower abutment pressure development within the backfilling area. The effectiveness of the CGFB technique is verified by a reduction in the vertical surface subsidence measured above the backfilled area.INTRODUCTIONUnderground longwall mining is the most efficient underground means to recover coal resources and is used widely in China, the US, Australia, and Europe. However, this type of mining has introduced some serious environmental impacts. Perhaps the most significant environmental issues are the surface and groundwater impacts associated with the formation of the subsidence basin (Bell and Donnelly, 2006). Backfill technology has been used for years to mitigate subsidence impact. Simply speaking, the backfilling technique places filling materials into the void left from the extraction of coal. When this material is placed within the gob, it is capable of partially supporting the overburden until a new equilibrium is reached. Essentially, the backfill material inhibits crack development and expansion caused by the strata movement and mitigates damaging ground deformations.The cemented gangue-fly ash backfill (CGFB) is one type of novel backfill technology, consisting of cement, coal gangue, fly ash, water, and additives in varying concentrations. The CGFB is mixed on the surface, pumped underground through a pipeline as a slurry, and placed in the void behind the longwall shield under the protection of specially designed hydraulic supports."

Jan 1, 2018

By Ed Van Eeckhout

As part of a U.S. Bureau of Mines-sponsored project on the utilization of "stiff' backflll to minimize potential rock burst hazards, a finite element study was undertaken to predict stresses and displacements around a stope mined up from the 5400 level of the Sunshine mine, Kellogg, Idaho. This stope was to be backfilled using a high-modulus fill. In preparation for that configuration, certain instrumentation was installed near the 5400 level to monitor stress changes. Due to untenable economics, only 2 cuts of the stope were ever made. This paper presents the results of the instrument readings taken during the first cut and compares them with the numerical predictions, as well as presents the modeling results of closure and fill stresses in the stope if it had been mined.

Jan 1, 1984

By Rob G. Jeffrey, Ken W. Mills, Jesse W. Puller

"A coal mine in New South Wales is longwall mining 300m wide panels at a depth of 160-180m directly below a 16-20 m thick conglomerate strata. As part of a strategy to use hydraulic fracturing to manage potential windblast and periodic caving hazards associated with this conglomerate strata, the in situ stresses in the conglomerate were measured using ANZI strain cells and the overcoring method of stress relief. Changes in stress associated with abutment loading and placement of hydraulic fractures were also measured using ANZI strain cells installed from the surface and from underground. This paper presents the results of in situ stress measurements and stress change monitoring undertaken as part of the hydraulic fracturing program.Overcore stress measurements have indicated the vertical stress is the lowest principal stress so that hydraulic fractures placed ahead of mining form horizontally and so provide effective pre-conditioning to promote caving of the conglomerate strata. Monitoring of the full-scale hydraulic fractures has confirmed the hydraulic fractures grow horizontally.Stress changes monitored during hydraulic fracturing formed part of a broader program to investigate fracture geometry and growth rates to confirm the characteristics of the hydraulic fractures placed. This monitoring showed that vertical stress in the conglomerate strata was being increased by up to 1 MPa in close proximity to the hydraulic fracture and had the effect of tending to promote asymmetrical growth of subsequent fractures about the injection borehole.Monitoring of stress changes in the overburden strata during longwall retreat was undertaken at two different locations at the mine. The monitoring indicated stress changes were evident 150 m ahead of the longwall face and abutment loading reached a maximum increase of about 7.5 MPa. The stresses ahead of mining change gradually with distance to the approaching longwall and in a direction consistent with the horizontal in situ stresses. There was no evidence in the stress change monitoring results to indicate significant cyclical forward abutment loading ahead of the face consistent with the observations of face conditions underground adjacent to both measurement locations. The forward abutment load determined from the stress change monitoring is consistent with the weight of overburden strata overhanging the goaf indicated by subsidence monitoring."

Jan 1, 2015

By S. MacGregor

The role of horizontal stress, its orientation and magnitude, in defining the behaviour of strata in underground coal mines has been well established. Poor panel layouts have led to gate end stress concentrations, roof falls and lost production. The ability to define the horizontal stress regime over a mine site has historically been limited to point measurements, in part due to technology and cost. Recent advances in the application of geophysical tools, notably the acoustic scanner (borehole televiewer) have resulted in a new technique to conduct stress measurements. By quantifying the nature of borehole breakout and the mechanical properties of rocks in which they occur, this technique provides the ability to: obtain a vastly greater number of measurements, both at different depths and spatial distribution, than other techniques such as overcoring or hydraulic fracturing readily obtain depth versus stress relationships define geotechnical domains on the basis of stress direction and in-situ stress magnitude for mine planning purposes This paper presents an overview of the technique and presents case histories in its application at a mine site in the Sydney Basin, Australia.

Jan 1, 2002

By Andre Zingano, Anderson Weiss

"The objective of this paper is to study the behavior of a low thick and low depth coal seam and the overburden rock mass. The mining method is room and pillar in retreat and partial pillar recovery. The excavation method is conventional drill and blast because of the small production. The partial pillar recovery is about 30% of the previous pillar size, 7m x 7m. The roof displacement was monitored during retreat operation; the surface movement was also monitored. The effect of the blasting vibration on the final pillar strength had been considered. Due to blasting, the pillar reduced about 20%. The consequence is more pillar deformation and roof vertical displacement. The pillar retreat and ground movement were simulated in a three-dimensional numerical model. This model was created to predict the surface subsidence and compare to the subsidence measured. This study showed that the remaining pillar and low seam reduce the subsidence that was predicted with conventional methods.INTRODUCTIONMining low coal seams (less than 1 meter) with the room-and-pillar mining method implies the excavation of part of the roof or floor to maintain adequate entry height for equipment and compliance with labor regulations with respect to ergonomic issues. The direct consequence of this is an increase in coal contamination and the increased cost of transportation and preparation at the plant. Traditional room-and-pillar mining only uses a development operation, even with a continuous miner or drill-and-blasting. Therefore, all the run of mine (ROM) coal is carried out with part of the roof or floor. However, if the retreat mining method were to be considered, the quality of the coal could increase because only the coal seam is excavated from the pillar recovery. The quality of ROM coal will increase, and the cost will decrease proportionally to the amount of coal produced from the retreat operation.However, the retreat mining with partial or total pillar recovery implies greater subsidence. This is particularly true if the coal seam depth is shallow, under 100m depth. Subsidence prediction in room-and-pillar retreat mining is complex; it depends upon the remaining pillar (stump pillar) size, as well as the pillar height, and the behavior of the pillar after retreat. This is related to the strength of the remaining pillar, which is related to the excavated method (drill-and-blast or mechanical)."

Jan 1, 2018

By Soheil Bahrampour

Void detection and identification of bed separation while drilling holes in rocks for roof bolting can be a great source of information for the evaluation of ground conditions and adjustment of ground control or support measures. This can be accomplished through the monitoring and analysis of drilling parameters by the roof bolter. This paper reviews work currently under way in a joint study between Penn State University and J. H. Fletcher & Co. The detection of voids, along with identification of rock types, can lead to development of 3D roof maps, which can subsequently be used to evaluate ground support and its suitability for given ground conditions in tunneling and mining operations. Existing algorithms for void detection utilize the sensory information of the drill unit, such as feed and rotary pressure, revolutions per minute (RPM), and penetration rate, to detect voids or joints on the roof/ ribs. While the void detection algorithms are being revised to allow analysis of available data from the existing sensory systems of the roofbolters with higher accuracy and lower number of false detections, additional sensors have been added to the drill to improve its ability for accurate detection of the voids and joints. This includes installation of vibration and acoustic sensors on a drilling unit at J. H. Fletcher & Co., and pertinent data analysis which are discussed in this paper. Initial results indicate that the data obtained by vibration and acoustic sensors at high sampling rates can be used to improve the performance of the void detection algorithms independently, and when combined with the modified algorithms using existing sensors, it can substantially improve the capabilities of current void detection system.

Jan 1, 2013

By Lightfoot. Nicholas, Na Liu

"Mining in multi-seam workings has been undertaken for many years in the VK Remnant pillars above and/or below current working areas have an important influence on retreat gateroad conditions at five of the remaining six deep coal mines. These interaction effects need lo be predicted ahead of mining so that longwall panels can be positioned to minimize roadway damage and to identify areas where additional support should be installed early into competent strata when and where it is most effective.Currently, three-dimensional elastic stress analysis using MAP3D is undertaken to predict local vertical and horizontal stress magnitudes during gateroad development and in front of the face on retreat. The predicted stress fields are often used as input to FLAC for roadway modelling.Using Maltby Colliery in South Yorkshire as a case study, this paper illustrates the MAP3D approach, together with its current limitations and uncertainties. Possible future improvements in the analysis method are proposed and the authors would welcome comments on these, or suggestions for alternative approaches.MODELLING OF MULTl-SEAM LAYOUT & MULTI-SEAM INTERACTIONThe remaining large coal mines in the UK arc operating at depths of 800-1, 150 m (2,625-3,773 ft). Production panels are now mined on retreat after the accompanying single entry access roadways have been completed. These gateroads are typically supported with a system of steel rock bolts and cable in the roof and steel bolts and glass re in forced polymer (G RP) dowels in the sidewalls.In addition to new panels being mined in the vicinity of old goafed districts, a significant amount of extraction has usually already taken place in coal seams above and/or below the current working areas. This means that there is also interaction between the current workings and the remnants of the old workings in other seams. As a consequence of the mining methods employed, old workings can have a complex geometry compri ing collapsed and partially collapsed excavations intersper ed with small and large pillars of unmined coal. The unmined coal pillar act as stress concentrators that carry the overburden load while the mined out excavations create stress shadows of varying degrees depending on how much collap e and reconsolidat ion has occurred. This is illustrated by a simple elastic model as shown in Figure I."

Jan 1, 2010

By Stephen C. Tadolini

Effective barrier pillar design is an essential component for safe and productive underground coal mining. Barrier pillar design methodologies that incorporate sound engineering judgment have been used for practical everyday usage. The next logical step is to utilize numerical modeling techniques that help combine practical experience and empirical observations into barrier pillar design analysis. A case study is presented that describes the barrier pillar design process, but also highlights the importance of considering the global mine response by evaluating: adjacent pillar stabilities, impact of intersection and entry widths, capacity of primary and secondary bolting systems and rib stabilization used for the safe and efficient removal of the longwall face equipment.

Jan 1, 2013

By Michael Gauna, Christopher Mark

"Coal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are almost always accompanied by a loud noise, like an explosion, and ground vibration. Bursts are a particular hazard for miners because they typically occur without warning. Despite decades of research, the sources and mechanics of these events are not well understood, and therefore they are difficult to predict and control. Experience has shown, however, that certain geologic and mining factors are associated with an increased likelihood of a coal burst. A coal burst risk assessment consists of evaluating the degree to which these risk factors are present, and then identifying appropriate control measures to mitigate the hazard. This paper summarizes the U.S. and international experience with coal bursts, and describes the known risk factors in detail. It includes a framework that can be used to guide the risk assessment process.BACKGROUNDCoal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are almost always accompanied by a loud noise, like an explosion, and ground vibration. Bursts are a particular hazard for miners because they typically occur without warning. During the years 2012-2014, serious coal bursts occurred at three different U.S. room and pillar mines. These events resulted in three fatalities and two permanently disabling injuries (MSHA, 2014; MSHA, 2013). In all three instances, the events occurred during pillar recovery at depths exceeding 1,000 feet (300 m). None of these three mines had previously reported a burst to MSHA. Coal bursts also occurred at three longwall mines during this same time period.Despite decades of research, the sources and mechanics of bursts are not well understood, and therefore these events are difficult to predict and control. Experience has shown, however, that certain risk factors are associated with an increased likelihood of a coal burst. A coal burst risk assessment consists of evaluating the degree to which these risk factors are present. In addition, some control techniques are effective in reducing the likelihood of an event or protecting miners from their effects."

Jan 1, 2015

By Sandin E. Phillipson

"On April 5, 2010 a massive dust-fueled explosion at a longwall mine in southern West Virginia claimed the lives of 29 miners. The mine had experienced large gas inrushes from the floor on two known previous occasions, and natural gas was found emanating from floor fractures behind the longwall shields after the explosion, indicating a likely fuel source for the initial ignition. In succeeding months, another longwall mine operating in the same seam 15 miles away encountered smaller inflows of natural gas that halted production from two different longwall faces. Production was halted at a third longwall mine, 30 miles south of the first, in May 2011, when explosive levels of methane were detected inby the longwall face on the headgate. The same mine was evacuated on March 20, 2014 when a series of floor gas feeders were encountered on the longwall face. A literature review indicated that there has been little documentation or description of these events, and that their size and frequency are unknown. The most significant floor gas inrushes in the United States are believed to have been associated with longwall mining in the Pocahontas No. 3 Seam of western Virginia, in which an estimated 5.8 x 107 ft3 of natural gas was expended from a floor feeder on the longwall face over a two-week period (Aul, pers. comm.).A variety of mechanisms and circumstances are associated with methane emanations from underground mines. Hyman (1987) defined an outburst as a violent, simultaneous release of gas and comminuted rock material into a working face or the interior of a borehole, and indicated that certain soft or fractured coals have a propensity for outburst based on gas desorption rates. In this mechanism, reservoirs of autogenic gas hosted in pockets of soft, crushed coal surrounded by harder coal are released suddenly as confining stress is removed by mining. Hyman (1987) also suggested that highly stressed, relatively gassy coal that is penetrated by mining-induced fractures could be outburst-prone. Clayton et al. (1993) and Ulery (2008) recognized the importance of faults as potential conduits for gas from adjacent strata into coal mines, and suggested that biogenic gas trapped in adjacent strata could migrate into mined coal seams due to a pressure differential. Ulery (2008) distinguished between an outburst and a blower, the latter defined as an event expending a large amount of gas over an extended time period, most often emanating from underlying strata, but without expulsion of coal or rock. Methane feeders are further defined as a subset of blowers that continually expend gas over a long period of time but at a lower rate. Many of the mechanisms discussed by Ulery (2008) relate to geologic features that can impound gas within the seam, releasing a voluminous amount when mining breaches the elastic dike, fault gouge, or other geologic structure that had restricted and compartmentalized coalbed methane migration. Thus, the events discussed in this paper can be described as blowers and feeders. However, detailed geological observations of the three longwall mines discussed in this paper appear to indicate a mechanism that is different from those described by Hyman (1987) or Ulery (2008), in that they did not involve coalbed-sourced gas, and the reservoirs were not hosted by coal seams."

Jan 1, 2016