Search Documents

By Dr. -Ing. Rainer Alles

Introduction Belt conveyors usually run in a straight line. The correct alignment is a major criterion for reliable functioning and optimum running properties. Any misalignment of the conveyor, especially mistracking of the belt, can have many negative effects. As a consequence of this, damage can occur on the belt and conveyor, some material can he thrown off at the edges and serious running problems can arise. In the worst case the belt can come off its supporting structure so that operations are brought to a halt. The absolutely straight alignment of a belt conveyor is actually impossible so that on closer observation every belt conveyor contains more or less sharp curves. Whereas on non-movable conveyors the deviations from the straight can he kept within the range of practical measuring accuracy by careful installation, movable conveyors in surface mining or belt systems in difficult terrain often contain curves that are easy to see with the naked eye. Below ground, too, alignment cannot always achieved to a desirable extent or is changed by geological faults over the years. Despite these unwanted curves, most belt conveyors perform their function reliably. In view of the belt tension, the belt tends to take the easiest path. This in general is the shortest distance between the pulleys on which the belt is tensioned and bent. This means for example that for a curve radius of 10,000 m over a flight of 100 m the greatest deviation from the ideal line is as much as 12 cm. And a figure of this magnitude cannot normally he accepted. In such cases, use is made of guide devices to properly train the belt if it doesn't center itself anyway. If it's possible to control the belt position over such unwanted curves. it can also he expected that the belt tends to follow the desired curved path within certain limits. I'd now like to cite a few examples to illustrate the ways and means of guiding a belt conveyor in curves. Cost-effectiveness The advantages of belt conveyors, in particular for longer conveying distances and mass flows have been known and undisputed for some time. However, there are often obstacles standing in the way of the concept of straight routing. If a belt conveyor is to bypass elevations or existing buildings or to follow the seam of underground deposits or a predetermined path, then substantially tighter radii and longer curves are desirable or necessary.

Jan 1, 1993

By J. B. Moritz

From the beginning, man has concerned himself with the task of controlling the elements and forces about him so as to provide a better and easier life. In the accomplishment of this task, he is required to utilize in the best way possible the resources which are available to him. In many cases, the available resources must bee refined before they are in a useable form. Many products in the mining industry fall into this category, as some form of refinement is generally needed to produce a saleable product. Over the years man developed more efficient ways of extracting the resources from earth through the use of electrical and mechanical devices. A reduction in manual labor, which is a by-product of increased efficiency through machines, has also been enjoyed. The combination of man's senses and new devices has also enabled man to reach a high level of control in the refinement process. Control of a process through machinery and man's senses has been termed an "art." Until recently man's senses (sight, feel) were the only method available for making measurements simply because suitable measurement devices (instruments) were not available. Even today some items cannot be measured and man's senses must be used. However, the development in our instrument laboratories tends to indicate that time will eliminate this. In recent years, control of many processes has been reduced to a science and part or all of the art eliminated. This does not imply that process art should be degraded; however, when a process is reduced to a science, uniformity of the product from day to day is attained. Decreased processing time and more efficient use of additives and raw materials are other benefits that result from control of a process when it is reduced to a science.

Jan 1, 1965

By Heather Wright

Shovel operators are one step closer to having a better tool to operate and monitor their equipment. The development of a unified shovel interface is proceeding into phase three, focused on producing a standard application programming interface (API) for connecting onboard devices. This solution will positively impact safety, performance and productivity, and is the result of collaborative work driven by the Global Mining Standards and Guidelines Group (GMSG). Proof of concept revealed During the spring of 2013, Peck Tech Consulting was engaged to develop the working proof of concept (POC) software implementation, which integrates multiple vendors? systems into a single interface using one-to-two displays. As a result, the GMSG developed a functioning, manipulatable, unified shovel interface proof of concept and unveiled it at the World Mining Conference in August in Montreal. The proof of concept effectively provides a unified operator interface that pulls together the many divergent systems onboard large shovels.

Mar 1, 2014

By C. B. Manula

Languages such as SIMSCRIPT and GASP have reduced the programming skills required to build simulation models, but not to a level where these can be used by a busy engineer or manager unless he has extensive programming experience. In an attempt to make simulation a more readily available tool, Sanford (1969) structured a generalized materials handling model (UGMHS)* for underground coal mining. The majority of materials handling systems consist of a set of moves and a set of pieces of equipment required to execute the moves. UGMHS gives a technique for describing and classifying the elements in these sets and then a technique for simulating the interactions of these elements as the materials handling system operates. To apply the model, the user simply furnishes data parameters and a fixed set of orders to the computer for his own problem. This new philosophy of dynamic simulation as applied by UGMHS was demonstrated in the paper by Sanford and Manula (1973). A dynamic model of underground coal mining was presented for the purposes of systems design and selection of equipment for a completely new operation and the analysis of existing ones for possible alterations, additions, and general improvements. The main differences between this application and its predecessors is the ability to transport material from multiple mine faces to multiple mine destinations and the ready adaptability to a wide variety of mine layouts. The second difference that characterizes the model is the deterministic simulation of equipment moves according to their mechanical capabilities and the physical profile of the mining scheme. Here, the computer generates performance data in the absence of time studies to compare equipment rather than operator performance.

Jan 1, 1974

By Fritz F. Prugger

This paper considers some of the main aspects of underground mining in the flat, rich, but deep lying deposits of Saskatchewan. It briefly describes the pertinent geological features as they relate co mining and the practical de-stressing techniques used to allow productive extraction in the high stress environment present in many of the province's mines. Fining layouts, materials handling and the evolution of some of the world's largest mining equipment are examined.

Jan 1, 1980

By V. Russel Burkhart

One of the most difficult items to justify economically on any budget is a training program. The costs can easily be identified--primarily the cost of the program and the inconvenience and cost of filling in for the men taking the training by working other personnel extra hours at overtime rates. Operating efficiency, higher productivity, increased plant availability, development of confidence, improvement in morale and less absenteeism are only a few of the benefits which far exceed the costs. A good preparation plant training program can accomplish more in 5 weeks than can be accomplished in five years of on-the-lob operation. During recent years, coal preparation plants have become more sophisticated and complex as the specification for coal used by electric utilities in their power plants have required improvements in coal quality to adhere to air quality regulations and to improve boiler performance and reliability.

Jan 1, 1981

By John MacDonald

An unstable economy has shown businesses what the mining industry has known for decades ? a successful business location today may not succeed in the future. Unexpected expenses, natural events and workforce changes have a big impact on the costs of production. To help focus production and maintenance budgets, mining executives are increasingly turning to production metrics to make key decisions. Role of mine and mill data Companies employ a variety of information systems to allow employees to accomplish their operational tasks, and each worker is focused on the metrics, or key performance indicators (KPI), for his or her individual function. For example, machine operators monitor throughput and cycle time to keep the machines running continuously and to meet daily production quotas. Meanwhile, the maintenance teams monitor machine performance, overall equipment effectiveness (OEE) and meantime between failure to predict and help prevent downtime.

Jan 1, 2013

By V. Svalbonas

In the establishment of a useful failure criteria for complicated, fabricated structures, two basic areas of knowledge must be evaluated: 1. The accuracy of the applied stress analysis must be known in comparison with actual stresses encountered during mill operation. 2. The metallurgical fracture properties of the basic materials must be established with reference to non-destructive examination (NDE) methods to be used during fabrication. Both of the above can only be evaluated by use of full scale tests on the structures, and/or components, of interest. This paper describes such tests and comparisons as applied to several large mill installations. In addition, weldment component fatigue tests arid flawed casting strain gauge tests are also discussed. The combination of such test results allows for the formulation of failure criteria directly applicable to the fabrication and examination procedures followed in grinding mill structure manufacture.

Jan 1, 1982

By D. J. Shalanski

In 1962 a computerized data processing system was first installed and programmed for the grading of direct-shipping iron ore from the Sept-Iles terminal of the Iron Ore Company of Canada. Over the years several changes and improvements have been incorporated into this system. It is the purpose of this paper to describe its present operation and features. Sept-Iles is located on the north shore of the St. Lawrence River, 500 miles north east of Montreal. The direct-shipping ore is received by railroad from Schefferville, 320 miles to the north in the Knob Lake Iron Range of New Quebec and Labrador. The shipping season extends from mid-March to December. The maximum tonnage handled in this period being 13,045,000 long tons in 1959. Crude ore receipts for 1974 amounted to 6,568,000 tons of direct-shipping and 4,700,000 tons of plant feed material from Schefferville. This was augmented by 4,447,000 tons of concentrate and 7,572,000 tons of pellets from Labrador City 200 miles north of Sept-Iles. The direct-shipping ore has come from as many as ten mines, and grade variations, even-within the same mines, have been sufficient to require blending for uniform, acceptable cargos. Shipments of low phosphorous, non bessemer and manganiforous iron ore are made, to Canada, the United States, Europe and Japan with grade variations to meet customers requirements.

Jan 1, 1975

By Stanislaw Wasilewski, Zdzislaw Krzystanek, Boleslaw Firganek

The experimental system for mine venti1ation control in Staszic colliery has two - level structure. In the lower - measuring 1evel the existing computer - based early fire detection system has been used completed with a number of additional sensors needed for ventilation parameters monitoring. The higher 1evel is a secondary computer equipped with a suitab1e dedicated software performing data processing according to the control a1gorithm. Direct control of air flow in a selected mine district is performed by means of a remotely controlled automatic regulator. Apart from functional tests of the system and its elements some research work has been carrying out in the colliery based on observations of transient effects caused by changes in air flow distribution.

Jan 1, 1989

By D. S. Parasnis

The early beginnings of mining geophysics in Sweden can be traced back to the reign of queen Kristina in the 17th century. The mine compass, consisting of a freely suspended magnetic needle in a casing, was in use certainly by 1640 and probably earlier for locating iron ore deposits. Whether the mine compass was a Swedish invention or not is an unsettled question since the possibility cannot be overlooked that the celebrated Nürnberg compass-makers of the 16th century may have constructed it for the first time(1). Be that as it may, the mine compass was very extensively employed in Sweden for more than two centuries and met with spectacular success in locating magnetic deposits under shallow overburden. Occasionally the diligent prospector would even be rewarded with a pyrrhotitebearing sulphide deposit, as witness many old sulphide-ore pits and some mines still in operation from the 17th and the 18th centuries. The mine compass measured only the orientation of the Earth's magnetic field and not its strength. Although it was improved in construction and sensitivity over the ages, no great strides were made in magnetic prospecting after the initial discovery of the use of the compass until Gauss, omnipresent in 19th century physics and mathematics, showed with the assistance of Weber how the strength of a magnetic field could be determined.

Jan 1, 1975

By George J. Karabin

Over the past few years, the use of fully grouted bolts to support the roof of underground openings has increased dramatically. While conventionally anchored bolts effectively reinforce the strata of over 80 percent of mine workings, the use of resin grouted bolts in areas of severe roof conditions has resulted in a substantial reduction in roof falls and an overall improvement in both safety and production. The Roof Control Group of Pittsburgh Technical Support Center, Mining Enforcement and Safety Administration, has conducted numerous field and laboratory investigations to isolate parameters which contribute to the effectiveness of both conventional and resin bolting systems. Specially developed strain-gamed resin bolts, compression pads and differential sag stations installed during the mining cycle have generated data reflecting the loading characteristics and resulting roof stability associated with each type of support. Additional investigations have produced optimum installation parameters of the two systems including the effectiveness of thrust/torque controls for conventional bolts and various bolt/ hole diameter combinations for fully grouted rods. Theoretical analyses, coupled with the actual field and laboratory findings and numerous installation observations have facilitated basic comparisons of the working mechanisms and failure modes of both resin and conventional systems.

Jan 1, 1976

By Joseph W. III Leonard

Most material balances on coal preparation plant flow diagrams are stated in tons per hour of solids and gallons or liters per minute of water. Balances expressed in these terms can be simplified when it is known that 4 gpm (15.1 L/min) of water is about equivalent to 1 tph (0.9 1 thr) of water. Some useful relationships follow

Jan 1, 1991

By Chee Theng

"Mining professionals are a resilient lot. Sure, copper prices are dismal, permitting processes seem interminable and the top mining companies are shedding jobs like a Shetland sheepdog sheds hair. All the more reason to hone technical skills, reconnect with old contacts and get one’s finger on the pulse of the industry.More than 400 did just that in the balmy sunshine and among the saguaro cactus of the Tucson venue of the SME Arizona Conference.Giving the keynote speech was Patrick Merrin, vice president at Hudbay Minerals (see box), while the luncheon speaker was University Distinguished Professor Mary Poulton, director of the Lowell Institute for Mineral Resources at The University of Arizona.“Attendance was great, especially given the copper price,” said Ta Li, vice president of business development at Tetra Tech and 2001 SME President. “The luncheon speaker was one of the better ones in recent years. Her talk contained a lot of fresh ideas, and practical versus theoretical concepts.”Talk about values, not economicsPraise was unanimous for Poulton, who gave a thought-provoking talk on “The New Face of Mining: The Culture Change for Compatible Mining.” Corporate social responsibility has been embraced by the metals mining industry, and it’s being done right, she said. “So why do we have more conflict? Why are there more protests? Why does permitting take longer and longer?” Poulton made a case for an approach based on compatible, rather than sustainable, mining to present a new face of mining that can be compatible with communities, cultures and the environment, and still be profitable. When the mining industry starts to talk about compatibility between what it is doing and what “me,” as the consumer, wants, what “we,” as citizens of a community, want, and what’s good for the “world,” we’re going to see the next culture change happen, she concluded."

Jan 1, 2015

By Donald Towse

Portland cement is a basic building material in every country in the world, and, fortunately, the raw materials required in its manufacture are widely distributed. It is a low-priced bulk commodity (price one cent a pound or less, with a density of 100 pounds per cubic foot.) Table 1. Approximate price per pound of selected mineral products. Copper 48 cents per pound Aluminum 27 Lead and zinc 15 Asbestos 3 to 18 Pumice 6 Sulfur 2 Bauxite (abrasive) 1.8 Barite 1 to 1.6 Cement 1 Primitive regions may get along without any Portland cement, but most countries use some, and it is one of the most widespread building materials, even if used in small quantities. Use of cement begins early in a country's development, and, because of local availability of raw materials, cement manufacture is one of the first heavy industries many countries desire. Use and manufacture of cement usually precedes other industrial materials such as steel and heavy chemicals, and consumption levels off for a long period during development of infrastructure and an economic base. With a mature economy comes a very high consumption. Per capita consumption varies ten times or more between nations (Figure 1).

Jan 1, 1970

By John Conway, Gerald Bennett, John Herrick

Research efforts which have led to reduced resin bolting costs at White Pine Mine are described. Key factor was development of the capability to drill small holes (1 1/8 in. diam) in the hard (20,000-30,000 psi) White Pine roof rock. Economic data comparing the 1 1/8 in fully-grouted Resin Bolt to the conventional 1 3/8 in fully-grouted bolt is also included. The development of a method which allows the Resin Bolt to hold itself in the hole thus removing the requirement for the operator to break his "work momentum" while he stops and waits for the resin to set is also described. This technique increased bolter productivity by 23% in a recent full-scale unit test.

Jan 1, 1974

By James A. Doolittle

In the underground type of mining operation, the finer portion of the waste material commonly is pumped as a hydraulic slurry to a tailings disposal pond. (1)* The tailings slurry is deposited via a pipe manifold system located around the perimeter of the pond. This method of deposition produces zoning because the coarser material tends to settle out immediately while the finer particles tend to remain in suspension and are deposited progressively nearer the center of the pond. The manifold system must be raised periodically as the pond fills with the tailings material. Over a period of time, this procedure will produce a zoned embankment known as a tailings dam. A typical pond and dam are shown in Figure 1. In plan view, the dimensions of tailings dams can be on the order of miles, with the height of the dam reaching 100 to 200 feet. Due to such factors as inadequate compaction, inherently low strength of the tailings material, and the possibility of high phreatic surface, many dams at some point become unstable, i.e., the factor of safety against a slope failure approaches 1.0. Remedial measures are required to improve the safety factor in order to prevent massive failure of the dam. In most cases, stability can be improved by effectively flattening the slope of the dam as shown in Figure 2, but this is not possible in every case. Occasionally, a tailings dam is constructed adjacent to a natural or legal boundary so that it is not possible to construct a conventional berm or to reduce the slope angle with earth moving equipment. Even a terracing process would require removal of the material and this may not be practical. In such a situation, an alternate scheme to improve stability must be found.

Jan 1, 1974

By L. Adler

When systematically compared to other engineering fields, mining engineering is distinctive in 1) having a total systems concern. 2) dealing with encumbered space and 3) requiring full spectrum practice. The total systems concern results from having to design and then co-ordinate in space and time several major systems: excavating and bulk handling, ground control, life support and normal support. This requirement favors a generalist rather than a specialist approach. In coping with encumbered space especially in underground coal mining, the uncertainties of geologic conditions are compounded by tightness, roughness, remoteness and hazards. Into this difficult setting the total systems * complex is "stuffed," adding congestion and interference. Because of significant ground deterioration a flexible "rapid in-out" approach is usually vital to mining. Full spectrum practice arises from the need to manage, as well as to plan and design, a labor intensive operation. Since market conditions can also fluctuate most aspects of administration are needed in many respects, mining engineering functions relative to civil engineering in a way similar to industrial to mechanical engineering, with encumbered space being crucial. On this basis stress is placed on: 1) personal relations, 2) field work and 3) entrepreneurship, viewing time as money. Specific recommendations for improving engineering, safety and management and leadership are made. Since most new deposits are marginal, by applying these recommendations with high technology they could possibly now be mined on a widespread basis.

Jan 1, 1985

Although grinding mill liner life has been the subject of extensive studies, evaluation of the effect of liner design on power consumption, a far more significant part of total grinding costs, has been less comprehensive. The factors that effect ball mill energy efficiency are reviewed, and attention is then focused on the mechanisms of grinding. The trajectory of the outer row of balls, with different lifting face angles, is derived, and basic recommendations for mill speed and liner configuration are presented.

Jan 1, 1981

By R. J. Weege

Conventional underground mapping methods and diamond drilling are being applied in a study to determine the nature of the copper ore occurrences near the footwall of the Osceola lava flow top, commonly referred to as the Osceola Amygdaloid. Our work to date suggests that structures formed by relatively impermeable barriers, created by flowage and injection of still-molten lava from the interior of the flow into the solidified, brecciated crust, acted as the ore receptacles. Ascending hydrothermal fluids traveling near the footwall contact were trapped and confined in these barriers which retarded the direct upward movement of the ore fluids and caused deposition of copper. Oreshoots located near the footwall appear to have been formed spatially' independently from the hanging-wall oreshoots by fluids traveling simultaneously, but along different channelways. The barrier concept as advanced by earlier writers to explain the concentration of the ore-bearing, fluids into broad shoots con¬stituting entire ore bodies is found to be equally as applicable for the localization of smaller oreshoots within the Osceola ore body.

Jan 1, 1962