Search Documents

By Ramesh Kumar Chauhan, Umakant Sharma, Manwendra Pratap Singh, Ashok Kumar Chadha

The power sector in India has an installed capacity of 267.637 GW as on March 2015. Out of this total installed capacity, the hydropower sector contributes 41,267.43 MW as renewable energy source. The development of various proposed hydropower schemes in India are primarily concentrated in mountainous regions of Himalaya and often involves underground tunnelling. Underground tunnelling of considerable magnitude is generally associated with adverse geological conditions and associated geological surprises. The main objective in case of Tunnels constructed especially for hydro projects, which carry enormous quantum of water is that, it should not leak. Moreover, the tunnels which are part of water conductor system should resist the inflow of water from the surrounding ground in order to avoid draining of natural water sources and lowering of existing groundwater levels. Lowering of water table may result in subsidence and damage to existing surface structures, loss of capacity of drinking water schemes and in some cases even catastrophic sliding of landmass. Grouting and pre-grouting in tunnels serve three different purposes i.e., Stabilization, Strengthening and sealing of the rock mass around tunnels to avoid leakage of water from tunnels. In present paper, results of grouting methodology adopted during final construction stage of RHEP (412 MW) along with the introspection of Water Pressure Tests conducted for determination of the efficacy of grouting were elaborately presented. The process, of contact and consolidation grouting which is respectively followed by water pressure tests along entire reach of HRT (15.177 Km long) were also addressed in detail. Pertaining to the results of water percolation tests (before and after consolidation grouting), it was also attempted to categorize the behaviour of different rock mass classes/ conditions in reference to different quantum of grout intake and corresponding Lugeon values. Importance of planned and dedicated successful grouting procedure adopted in hydropower project at RHEP is also emphasized.

Jan 1, 2016

By R. A. Matuszak

Historically most mine management teams have been forced to operate in a more or less subjective manner. The objectives of mine management are simple and clear. Like other operational managements, mine management teams have the traditional well defined goals of improving efficiency and production while decreasing costs. Unlike other operational managements however, mining teams deal regularly with a vast assortment of uncertainties caused by: - Key production tools being mobile and widely dispersed, and - Non-uniform mining conditions At best in most operations these conditions cause obstacles to productivity and at the same time cause long delay in managment awareness of the obstacles. Planning with delayed feedback of information about necessary deviations is incomplete planning. For these reasons increased operational efficiency remains a constant though somewhat elusive goal.

Jan 1, 1985

By Kenneth Denton, Michael Cutts, Andrew Bursey, Eric Eisold

Phase III of the Orme Street Combined Trunk Relief Sewer project connects two existing 2.13 m diameter combined sewers to a new 3.66 m diameter relief sewer at 7locations along a 970 m alignment in downtown Atlanta. The alignment was enveloped by adjacent structures and utilities. The project was constructed below the groundwater table through compressible residual soil, rock and mixed face using a myriad of construction techniques, including compressed air NATM and jet grouting. Numerous design and alignment changes and accommodations for existing utilities and conditions were made during construction. The authors believe this to be the ?rst NATM project in North America utilizing compressed air tunneling.

Jan 1, 2003

By Dipl. -Ing. H. -J. Sager

The ‘Westerschelde Tunnel’ underpasses the estuary of the Schelde in the Netherlands. The tunnel will consist of two tubes which are driven by two hydroshields (slurry shields). The tunnels will each have a length of approx. 6.6km and a bore-diameter of 11.33 m. Demanding ground conditions had to be considered during the design of the shield machines. Loose sands, extensive clay formations and high ground water pressures of up to 6.5 bar will be encountered during the tunnel drive. The tunnelling activities will start in the middle of 1999 and are scheduled to end by the end of 2001.

Jan 1, 1999

By Frank T. Wheby, Edward M. Cikanek

A computer performs all logic and computations customarily done by hand in preparation of engineers' estimates or contractors' bids on tunnel-shaft systems. The program described is based on construction methods, work forces and equipment selections corresponding to the current state-of-the-art of rock, soft ground and cut-and-cover tunneling. The program contains logic to permit estimates of cost of complicated tunnel-shaft systems; it is not necessary to input quantities, as the program calculates those from the tunnel design that is internally generated. In any estimate, the program bases its cost computation on user-input requirements and site conditions, such as tunnel shape and size, shaft depth, ground characteristics, construction methods, and other factors. To provide great flexibility, the user of the program is provided with options for accepting designs built into the program or overriding these designs by his own inputs. An illustrative example is presented.

Jan 1, 1974

By T. G. Rozgonyi

The basic goal of this investigation was to determine the degree of drying of high moisture lignite through the use of high temperature and pressure steam autoclaves. Specific items studied were: a) the effect of lignite particle size, b) steam temperature and pressure required, and c) the time of ahydration. Although removal of sodium, ash, sulfur and other ash-forming minerals was not the goal of this study, basic analysis of effluent water showed organic material and alkalai metal content. Removal of inherent moisture from run-of-mine lignite was tested by lock-feeding the lignite, which was previously sized by screening into 25 kg autoclaves. High pressure, up to 4.053 MPa (588 psi), saturated steam was then introduced into the pressure reactor. Reaction time, pressure, temperature, and depressurization rates were strictly controlled for each reactor test run. Results indicate that about 80% of lignite total moisture was removed, including some of the inherent moisture, yielding a non-oxidized, and thus stable, lignite product. As stated, a side benefit occurred as some reduction of non-combustible portions of the lignite also took place. The conclusion reached as a result of the tests is that the steam-drying process can be successfully applied to reducing moisture in lignite, and may be considered for additional studies on acceleration of the coalification process. On the basis of the data presented, the author believes that lignite can be economically upgraded in steam autoclaves by simultaneously reducing the moisture content by 80 percent and the sulfur content by at least 50 percent. Upgrading the lignite by this method will result in large energy and financial savings.

Jan 1, 1984

By J. S. Gardner, R. Woolacott, P. D. Robinson

In 1917, U.S. Coal and Coke Company, a subsidiary of U.S. Steel, opened Mine 31 and built the community of Lynch, Kentucky. For the time this was truly a major engineering accomplishment. It was documented in Howard N. Eavenson’s 1939 AIME paper, “Coal Through the Ages.” In 1996, Arch Coal donated the Portal 31 property to Harlan County for public use. In 2003 the Southeast Education Foundation, Inc. and the Kentucky Coal Museum plan to open the Portal 31 Exhibition Mine to the public to tell the story of Kentucky coalmining through the decades. This presentation will summarize the history of the project, efforts to bring it to reality, the engineering problems, and the challenges of providing a safe environment for visitors.

Jan 1, 2003

By Karl Gunnar Holter, Frank Clement

"INTRODUCTION Typically waterproofing of conventionally excavated tunnels has been done by installing pre-fabricated sheet membranes between the primary temporary support lining and the secondary permanent inner lining. The membrane acts as a separation or sliding layer between the linings, which is often desirable. The geotextile installed behind the sheet membrane provides the required drainage and protection of the system. The design of the tunnel lining is strongly influenced and limited by the use of waterproofing sheet membranes. Since primary and secondary linings are separated from each other, forming a double-shell lining system. In that case the secondary lining must be designed for all permanent loads, although the sprayed concrete primary lining continues resists ground and water loads for a long time after construction. Significant progress has been made in sprayed concrete technology over the last two decades, with advanced admixtures, as well as the improved application technology using spraying robots. The development of new admixtures like superplasticizers based on poly-carboxylates, alkali free accelerators and silica fume, enables designers to use permanent sprayed concrete linings (SCL) increasingly for long-term service life. When designed and applied correctly, sprayed concrete can be considered as permanent. The use of spray applied membranes has seen increased use over the last decade in some countries, and demonstrated functionality and cost-effectiveness in several situations. This paper describes the use of the sprayed waterproofing membrane MasterSeal 345, an EVA polymer based product, and the practical experiences from several projects. SPRAY APPLIED WATERPROOFING MEMBRANES The sprayed waterproofing membrane is polymer based and has been especially developed for underground structures. The membrane is applied between primary and secondary concrete linings and develops high bond strength on both sides to the concrete (doubled-bonded)."

Jan 1, 2016

By E. G. Joe

Introduction Uranium mining has been actively carried on in Canada for over twenty-five years mainly in Ontario at Elliot Lake in Bancroft, and in Northern Saskatchewan at the operations of Eldorado Nuclear Ltd. During this period, approximately one hundred million tons of mill tailings have been created and lie mainly on the surface close to the mining and milling installations. If all of the present reserves of uranium ores in Canada are mined, a further eight hundred million tons of mine tailings could be created in Ontario, Saskatchewan, the Northwest Territories, Labrador and British Columbia. The present control of effluents from existing tailings is managed by the operating mines under the regulations of both federal and provincial control agencies. It is the long-term effect of these tailings on the environment that has not been clearly defined or measured. Several years ago, the Canada Centre for Mineral and Energy Technology of the Department of Energy, Mines and Resources, embarked upon a program of research directed at the long-term effects of uranium mine tailings. Much of the research to date has been on tailings in the Elliot Lake, Ontario area where some tailings piles have existed for over twenty years. The program consists of two projects, one to address the problem of existing tailings and the other to examine alternatives in the management of current and future tailings. TAILINGS CHARACTERISTICS Uranium tailings are generally the result of sulphuric acid leaching in which the uranium and alkaline minerals such as carbonates and chlorites are leached out. If the ore contains sulphides, these minerals potentially present an additional hazard of acid generation over time and could increase the mobility of heavy metals and some radionuclides such as thorium-230. Except for the extracted uranium, most of the radionuclides from the ore remain in the tailings pile. Uranium ores in Canada span a wide variety of mineralization and associated gangue composition. Uranium minerals include pitchblende, uraninite, uranothorite, brannerite and the phosphate uranium minerals autunite and saleeite. Gangue minerals vary from acid consuming carbonates, and chlorites to acid producing sulphides and inert silicates. With such a wide variety in ore composition, the characteristics of the resultant tailings in Canada are in many cases site specific and the solutions to the long-term effects of these tailings may also be site specific.

Jan 1, 1980

By A. Wahab Khair

There are a number of factors, including mine geometry, local geology, geotechnical properties of overburden materials, surface topography, sequence of overburden strata, and extraction rate, affecting characteristics of surface subsidence imposed by large underground excavation. Among the factors, the first three have the major impact on magnitude and area of influence of final subsidence. Hence, a model has been developed, considering mine geometry and geologic and geotechnical properties of the associated area, to predict maximum possible subsidence and subsidence profile at any cross-section within the subsidence influence zone. Based on extensive field measurements and mechanics of strata behavior, under the action of overburden pressure in the vicinity of the large underground excavation, the vertical plane of influence zone has been divided into five areas: 1) excavated, 2) caved, 3) fractured, 4) highly deformed but continuous, and 5) subsided zones. In the final state of subsidence each area maintains a certain volume expansion/contraction, i.e. a factor which depends on geologic, geotechnical properties of overburden strata and state of stress within the subsidence trough. The cumulative volume expansion and contraction partially compensates for the extracted volume and the difference between the two is reflected as the subsided area in the form of the area within a curve defined by a probability function. The input parameters for the model are mine geometry (i.e. length and width of the panel), depth of cover, and geologic and geotechnical properties of overburden strata (i.e. percentage of hardrock, sandstone and limestone, and soft rock, shale within the overburden strata and Rock Quality Designation). The model calculates angle of draw for the site, expansion factor for each zone utilizing empirical relationships, maximum possible subsidence and plots the subsidence profile curve. The model is developed for a longwall excavation with unique characteristics of prediction of angle of draw and maximum possible subsidence for a given geologic and mining condition at any cross-section within the influence zone of subsidence.

Jan 1, 1986

By Daniel Saramak, Agnieszka Saramak

A big issue in crushing and grinding operations in raw materials handling is high energy consumption and low breakage effectiveness. According to the Legendre [7], only 10% of energy input is directly consumed on the feed material breakage, while the remaining portion is dissipated in the form of heat and noise [8]. In the industry of limestone powder production, the grinding operations constitute integral part of technological circuits, and the energy consumption in operations of industrial comminution consume as high as 2% of world energy [14]. High-pressure grinding is the technology with proved energy benefits both in ore processing circuits and in limestone grinding. The promising results concerned mostly the achieved energy savings and good results of material breakage were achieved and demonstrated in numerous investigations [1,3,12]. However, it appears that a proper selection of operational parameters of the press devise, determination the feed material characteristics and adjustment of process course san be of a key-significance in improving an effectiveness the HPGR operation. Operational parameters of devices and process course should be verified towards the characteristics of the feed material, which mainly applies to the particle size and shape of the feed material and its moisture, and also mineralization in case of ores [2,4,9]. There are various investigations concerning an impact of the operational pressing force on comminution results which mostly refer to the determination of energy consumption and crushing ratio [5,6,10,13]. Investigations on the moisture content are less common, however their results suggest that, in general, the HPGR feed with higher moisture shows the tendency to higher comminution intensity, while the energy consumption increases together with increasing of feed material moisture. Investigations on olivine sand feed [11] showed that crushing ratio decreases for higher moisture, especially when the material is crushed at higher pressing force. HPGR devices, however, shouldn’t be regarded as a unique and perfect solution for comminution of each type of material. But they indeed may bring technological and economic benefits, comparing to conventional crushing and grinding machines, resulting in more favourable breakage of material particles and lower consumption of energy per unit mass of processed feed material.

Feb 1, 2025

By Nico Sutmoller, Rich Palladino

Underground voids present a unique geotechnical engineering challenge. This paper will address materials and transportation mediums that are typically used for backfilling underground voids with native material. After reviewing traditional backfill and transportation methods, this paper will explore the advancing technology of foam transportation and the advantages of using this technology for transporting fill materials into underground voids to backfill them with Liquid-Sand. The paper will also review the benefits that Liquid-Sand brings to these applications and highlight specific case studies in which foam transportation has proven effective and provided cost-effective, environmental benefits.

Feb 1, 2025

By John N. Murphy

In fiscal 1996, the US Congress directed that the US Bureau of Mines (USBM) be closed. Certain functions were reassigned to other agencies. The remaining employees were separated and the unoccupied sites were decommissioned. As a result, 12 locations were closed and about 1,200 employees were terminated in March 1996. About 600 employees at five locations were reassigned to other federal agencies. This article provides a summary of the continuing functions, the agencies involved and the points of contact for each continuing function. The functions that were discontinued are also identified. The functions that have been maintained and transferred to other agencies are: ? Portions of USBM's Mineral Information and Analysis program formerly conducted in Washington, DC and Denver, CO were assigned to the US Geological Survey (USGS). ? The Mineral Land Assessment program in Alaska (Anchorage and Juneau) was transferred to the US Bureau of Land Management (BLM). ? The Health and Safety Research program in Pittsburgh, PA and Spokane, WA was reassigned on an interim basis to the US Department of Energy (DOE). In fiscal year 1997, it was permanently assigned to the National Institute for Occupational Safety and Health (NIOSH). NIOSH is part of the Centers for Disease Control and Prevention within the US Department of Health and Human Services. ? Environmental Research at Pittsburgh, PA was assigned to DOE. ? Materials Research at Albany, OR was assigned to DOE. ? The helium program was assigned to BLM, where it will be managed pending privatization. ? Coal and noncoal mine maps were transferred to the Office of Surface Mining Reclamation and Enforcement (OSMRE). The following locations were closed: ? Research centers in Denver, CO; Minneapolis, MN; Reno, NV; Rolla, MO; Salt Lake City, UT and Tuscaloosa, AL. ? Field operations centers in Denver, CO and Spokane, WA. ? Washington, DC headquarters office. To provide a concise picture of all of the affected functions, the following is a synopsis of the USBM program functions and facilities immediately before the closure. There were two principal programs: information and analysis, and research.

Jan 1, 1997

By J. Kenneth Wittle

The DC Graphite Melter has been shown to be capable of processing radioactive waste materials. The process is characterized by its high temperature capability and operation in a closed system. From an environmental perspective, the control of emissions coupled with destruction for hazardous organic materials is mandatory. These same characteristics may be applicable to the minerals processing industry. Under normal operation, the system reaches temperatures for nominal operation of 1600°C, with an arc temperature in the order of 5000°C. The system temperature is determined by the melt temperature of the material being processed. In testing of a 750 lb/hour unit, temperatures of 2200°C were reached. Current focus is on finding waste treatment and metals recovery opportunities in the metals processing industry for his innovative technology.

Jan 1, 1999

By Andrew L. Mular, Richard R. Klimpel

Optimization strategies of possible interest to mineral processing are reviewed and typical strategies initiated in processing plants to date are discussed. Both On-Line and Off-Line optimization procedures have been employed by industry, assisted either by operators or by digital computers. In every case, dollar benefits have accrued.

Jan 1, 1991

By Peter G. Chamberlain

Novel and innovative mining methods are attracting the attention of mining engineers at an unprecedented level. Historically, the US mining industry has responded rather conservatively to new technology. The financial difficulties affecting the domestic mining industry in the early 1980s changed attitudes toward new technology. The market contraction during that period, coupled with an expanding world mine capacity, created a serious oversupply of many raw mineral products. Many mining companies found that retaining a share of world markets while making a profit required drastic cost-cutting measures.

Jan 1, 2008

By A. B. Mayer

A generic task summary for design and implementation of hydrogeology programs at open-pit mine operations is presented as a guideline for management. Rigorous assessment of the local and regional hydrogeologic system is necessary to plan dewatering activities and to address environmental concerns. Dewatering activities include calculation of dewatering requirements, design of dewatering systems and evaluation of dewatering-water disposal areas. Environmental concerns include calculation of dewatering and water-disposal impacts, mitigation of soil and ground-water contamination and acquisition of water rights. Three-dimensional numerical models are commonly used to support these analyses. A thoroughly developed hydrogeology program provides an interactive basis for dewatering feasibility decisions and for support of environmental permits and regulatory compliance.

Jan 1, 1993

By Christian F. Baiz

A new agenda has risen. Born out of governments' policies and world economies, the years ahead will carry with them reduced growth. For inflation dependent and capital intensive industries, such as metals and mining, as well as most other natural resource industries, a period of long-term contraction in outmoded and costly capacity will evolve. This will be supplanted by new, lower cost capacity in some cases, but only if the total cost of production, including cash operating and debt service costs comes in at or below current market conditions. The industrial outlook can be characterized as bearish. As one major U.S. bank economist put it, mining companies planning their five-year forecast from 1984 out, should take the current market conditions and straight-line them to the end of the decade. With low growth and low inflation, the real price of metals will remain flat or slightly declining. As a result, capital funding will be problematic. The low cost producer, that is one with low cash costs and low principal and interest costs per unit of production, will succeed.

Jan 1, 1984

By J. H. Dietz

The electric assist option for diesel-electric trucks can improve truck productivity while maintaining the inherent flexibility of a truck and shovel operation. In addition, the resulting cost reductions offer a rapid investment payback for many mine situations. A review of the present technology and performance experiences verify the projected benefits in productivity and operating cost. New technologies can further improve the productivity/cost scenario.

Jan 1, 1984

By W. Reed

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This paper examines factors that had a significant influence on mine face ventilation design during the past century. Several “milestone” events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative ventilation designs and a consistent commitment to mining health and safety.

Jan 1, 2007