Search Documents

By H. Y. Yang, L. L. Tong

Semicontinuous-flow, multistage biooxidation experiments of a Chinese refractory, high-sulfur gold concentrate were conducted with different pulp densities for gold recovery. The maximum iron, sulfur and arsenic oxidation rates of 90.0, 88.8 and 96.4 percent, respectively, were obtained in the experiments with 5 percent pulp density. The highest gold and silver recoveries of 96.1 and 68.9 percent, respectively, were achieved by cyanidation. The negative effect of high pulp density on biooxidation was related to the decrease of free and adsorbed cell concentrations with increasing pulp density. The data of iron oxidation from the semicontinuous biooxidation experiments were best fitted by a shrinking core model in which the chemical reaction controlled the rate. The dissolution kinetics of sulfur and arsenic were therefore analyzed by a shrinking core model in which the internal diffusion controlled the bioleaching rates. For the quantitative description of biooxidation efficiency, two parameters — mass dissolution rate and volume dissolution rate — were proposed. In the first stage, the mass dissolution rates of minerals were negatively correlated while the volume dissolution rates were positively correlated with the actual pulp density. The iron and sulfur mass dissolution rates decreased with increasing actual pulp densities in the third and fourth stage, while linear increasing relationships between the volume dissolution rates of minerals and the actual pulp density were observed from the second to fourth stage. The highest mass dissolution rates of minerals were obtained in the first stage with 5 percent pulp density. The highest volume dissolution rates of minerals were obtained in the first stage with 15 percent pulp density. Compared to the volume dissolution rate, the mass dissolution rate was more intuitive to reflect the negative effect of high pulp density on biooxidation efficiency.

By Downing Terry L.

Dry mineral beneficiation methods have been developed for separation of borate minerals from montmorillonite claystone gangue. The methods include the use of newly developed dry high intensity magnetic separators. The application of these methods has the potential for economic benefit at U.S. Borax Inc. in three areas: ? Processing surface impoundments (ponds) material. ? Pre concentrating ore to be fed to primary refinery. ? Concentrating borate minerals to produce potential products.

Jan 1, 1995

By D. T. Kirkwood

The practice of impounding mine water and liquid fine waste in underground mines is increasing. Often these underground impoundments are created by constructing seals or bulkheads designed to withstand the expected hydraulic pressures. Occasionally seals are built for another purpose, usually to act as explosion-resistant ventilation barriers. Due to factors such as clogged drain pipes or unexpectedly high inflow rates, these explosion-resistant seals sometimes become subjected to hydraulic pressures. The incidence of seal failures due to inadequate design and/or construction is also on the increase. Fortunately, to date, no lives have been lost by water seal failures, but a clearer understanding of the design and construction considerations specific to water seals is vital to keep this from occurring in the future. This paper presents technical considerations for the design and construction of seals which will specifically be required to withstand hydraulic pressures in underground mines.

Jan 1, 1995

By M. D. Ross

Complex combinations of technical, economical, safety and environmental factors are causing mining engineers everywhere to review their operations. Naturally, some of the traditional methods still have a large role to play because they are, in certain circumstances still adequate and are well understood. But, as circumstances change, a new approach is required. The combination of technical and economical reasons for introducing Long- wall mining in some seams in the United States is associated with strata control. Other reasons include simplifications and improvement of ventilation, reduced coal dust, more output from each unit and crew, increased percentage of recovery from each area of the coal deposit, and reduction of rock dusting. The innovations which transformed Longwall mining from a cyclic to a continuous mining system were the armored conveyor and power loading machines, but the crucial breakthrough for application to high production was the development of the powered roof support, which at once gave the system the advantages of mastery of strata control, increased rate of advance, significant reduction of manpower, and increased safety.

Jan 1, 1974

By Joseph M. Denk, John N. Baran, William J. Francart

Filling or sealing shafts of underground coal mines is required when the mine is declared inactive by the operator, permanently closed or abandoned for a period of time greater than 90 days. Although shaft filling requires the use of incombustible materials for the first fifty feet of the shaft, a sparking potential may exist which has been reported to be the cause in at least one shaft-filling explosion. This paper outlines the method used at the explosion site to monitor mine gases within the shaft to assure the safety of the workers involved in the remainder of the shaft-filling operations. Gases which were monitored include methane, oxygen, carbon monoxide and carbon dioxide. Continuous sampling was conducted twenty-four hours per day to determine the methane liberation and accumulation of gases within the shaft. Once gas concentrations were evaluated, the need for ventilation in the shaft was obvious because methane accumulations within the shaft were in the explosive range. Several methods to ventilate the shaft were explored. The most practical seemed to be the dilution of gas concentrations with compressed air to inject a quantity of fresh air into the shaft. But, when the compressed air was stopped, a buildup of an explosive mixture reoccurred. The pattern of gas accumulation was then studied to find the correct combination of ventilation and shaft-filling time periods which would a1 low for the greatest reduction of the potential for an explosion. Gas concentration sampling continued during the remainder of shaft-filling operations at this shaft and four others at the same mine. In conclusion, this paper illustrates some of the problems which are often overlooked in a shaft-filling operation. If addressed, the work can be done in a safe and feasible manner.

Jan 1, 1987

By M. K. Rizkalla

This paper discusses the time-dependent behaviour of rock when it involves the presence of several layers of rock strata in the vicinity of mine openings, mining in sequences and the placement of backfill. The paper describes numerical techniques which proved useful when such situations are encountered in practice. The model is elastoviscoplastic. At given time stations, short term loading or changes can be made to the creep behavior of the rock. The modelling technique is first described and is followed by simulations of stresses and displacements in a potash mine with the primary objective to demonstrate the effect of such aspects as mining and fill sequences in 3-D. This involves cutting finite elements representing the strip of the mining face and simultaneously filling those elements representing the newly placed fill. The stiffness of the fill varies with the degree of compaction at each point. In this way, the effect of the time of fill placement, the gap between the top of the fill and the back as well as the degree of compaction are simulated. The second example is a 2-D problem simulating the long term effect of backfill, as a material compacting with time, on the settlement of the layers above it as well as the closure of the room.

Jan 1, 1996

By G. T. Lineberry, W. J. Wiehagen

A paradigm shift As market economists, mine managers are interested in "staying in business" and even "prospering." Bottom-line results are the "order of the day." Concern for bottom-line results can invoke questions such as how much was produced, at what cost, and was anyone injured? While these questions will always carry everyday emphasis at the mine, they are fundamentally lacking in that they often appear, especially to lower levels of management and to the production worker, as pre-eminent concerns. Driven by market economics, many organizations have decentralized, outsourced, downsized, restructured and formed new coalitions. Investments in new technology and a concentration on productivity have been an essential part of these changes, contributing to improvements in both safety and efficiency. A reason for (and, perhaps a result of) these improvements has been the development of a highly experienced and flexible work force. This situation presents an interesting opportunity to modify a few paradigms about work life in general, and perhaps a few paradigms about how we invest in the miner, in particular. Studying these issues now night offer some interesting opportunities for the Future, as the foundations for the next generation of mine workers are laid. With the average "experienced" U.S. miner five to fifteen years from retirement, perhaps a key determinant of future success in the world market might be how well we make the transition from today's work force to the work force of tomorrow. We can ill afford to wait a few more years to tap into the special knowledge residing within a veteran mining work Force. The Work Crew Performance Model (WCPM) is one approach to defining, capturing and transferring this expertise. The WCPM suggests a paradigm shift, moving from a focus on products (quantity) to a focus on the process (quality). It also involves a slight change in the process -- a different way to think and work. Of great importance, it entails a belief and a commitment to people within the organization; a commitment to collect simple (but interesting) data; exploration for insightful ways to plot and integrate that data; and finally the search for creative methods to reinvest that knowledge back into the organization, that is, back into the work force. As a way of thinking, the WCPM subordinates information about how much is produced daily or how many were injured over a year's time to concern and detail for how the individual's and the work crew's performance contribute toward meeting organizational goals. Drawing upon the expertise within members of that work crew to address and solve operational problems is one approach for meeting organizational goals. This everyday focus on how we work is hypothesized by the WCPM to make the difference between a good section supervisor and the average one; an exemplar continuous-miner operator and the run-of-the-mill one; a mining crew that produces consistently high quantities, but, inadvertently, degrades the production of other units. The WCPM permits objective and reliable performance data to be collected. This data then can be used to define variability within tasks of work crew members; to relate observed variability to a cost consequence; and to more meaningfully analyze performance through the integration of traditional analytical tools, such as the production simulator, CONSIM, with a recommended behavioral approach, the WCPM. Basis for engineering test Most equipment selections and purchases involve a field trial test of the system. Technology is routinely bench tested at the manufacturer's facility, government agencies and the mine site. The WCPM suggests a similar, but more practical, method for testing the performance of a work system -a test for how technology is used (by people) at the work site. It implies learning from veteran mining personnel that have gone well "beyond the book." This approach to learning and to integrating training with everyday work life can help answer questions such as: What constitutes desirable perfor¬mance as, for examples, a shuttle-car operator, a miner operator or a bulldozer operator; what characterizes exem¬plary performance within the context of the work system, the technology and the work crew; how can investments in the worker he linked to measurable results within the organiza¬tion? This paper explores these questions and makes recom¬mendations for enhancing the cost-linkages between invest¬ments in people and the mine's monthly cost sheets.

Jan 1, 1996

The extraction and recovery of gold from copper electrorefining slimes by leaching and solvent extraction using dibutyl carbitol (DBC) has been practiced for several decades. Yet, the deportment of some common elements in this process has not been reported. The focus of this paper is to report the behavior of copper, bismuth, silver and selenium during the processing of industrial solutions by batch and continuous extraction on the laboratory scale. It was found that DBC, while an excellent extractor of gold from a highly oxidative chloride leach solution, also loads significant quantities of Cu, Bi, and Se. Silver was not present in significant quantities in the leach solution nor did it load appreciably. The deportment of gold and impurities are reported for batch and continuous operations of a two-stage extraction process using distribution ratios and separation factors.

Jan 1, 2010

By J. F. Strunk Jr., K. M. Maestas, Y. Chai, R. Legrand, R. L. Henry

"Groundwater with elevated sulfate and metals was treated using a sulfate-reducing pilot PRB consisting of a series of six 55-gallon drums filled with ZVI (Fe0), wood chips, brewer’s grain, limestone, and emulsified vegetable oil (EVO). Sulfate was reduced from >3000 to <250 mg/L and Cd, Cu, Mn, Ni, and Zn concentrations declined up to 3 orders of magnitude in 2 months. After 6 months of operation at a 7.5-day retention time, sulfate broke through. The system was then rejuvenated by injecting EVO in each drum and operated for 5 more months at a 9-day retention time. Sulfate-reducing bacteria in the pilot system grew by 3 to 4 orders of magnitude in 2 months. Some cementation of the PRB media was observed in the first 2 drums after processing 25 pore volumes of water, due to preferential upstream precipitation of sulfides; this can be avoided through operational modifications. Resulting permeability losses were estimated at 0.1% to 1% per year. Absorption/desorption was tested at bench scale to evaluate the use of various oil-soaked sorbents as a slow-release source of dissolved carbon. The tests show that oil sorbents can increase the useful life of a PRB between oil refills to over 100 pore volumes. INTRODUCTION High sulfate concentrations, low pH, and dissolved metal exceedances are common characteristics of mining-influenced water (MIW). Above-ground such MIW is commonly treated using biochemical reactors (BCR). In a BCR, water generally flows vertically downward through a layer of biomass, such as wood chips, manure, etc. The dissolved organics resulting from the decay of this material are oxidized first by microbes using oxygen; when oxygen is exhausted, other bacteria can use nitrate, and then sulfate to oxidize organics. Sulfate-reducing bacteria (SRB) reduce sulfate to sulfide, which quickly reacts with metals to form largely insoluble and stable metal sulfides. These reactions can be summarized as follows:"

Jan 1, 2016

By W. R. Reed, G. J. Joy, B. Kendall, A. Bailey

"Testing of the NIOSH-designed roof bolter canopy air curtain (CAC) has gone through many iterations demonstrating successful dust control performance under controlled conditions. J.H. Fletcher & Co. (Fletcher), an original equipment manufacturer of mining equipment, has further developed the CAC concept by incorporating it into the design of its roof bolting machines. A new CAC design has been developed incorporating the results of testing of the NIOSH design and the recent Fletcher design. Observations from smoke testing conducted on this new CAC design in a laboratory setting show promise for improved performance. INTRODUCTION Exposure to respirable coal mine dust can cause coal workers’ pneumoconiosis (CWP) otherwise known as black lung. If silica is present in the dust, the miner may develop silicosis in addition to CWP. CWP and silicosis are occupational respiratory diseases that are ultimately fatal and have no cure. The only method of prevention is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit (on an MRE basis) for respirable coal mine dust is 2.0 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities [30 CFR 70.100 2015]. Recently enacted legislation changes this standard beginning in August 2016 to 1.5 mg/m3 for a full working shift [Federal Register, 2014]. If the respirable coal mine dust contains more than 5% silica, the applicable respirable dust standard is reduced; calculated as 10 divided by the percent quartz present [30 CFR 70.101] so that the effective exposure limit for respirable quartz is 0.1 mg/m3 for a full working shift. Sources of exposure to respirable coal mine dust for the roof bolting occupations include infrequent maintenance and cleaning of the vacuum dust collection system and operating the bolter downwind (in the return air) of the continuous miner [Goodman and Organiscak, 2003]. Recent studies have demonstrated that vacuum dust collection systems are effective in capturing bolter-generated dust, if maintained and operated correctly and if proper face ventilation techniques are used. However, most exposure to respirable coal mine dust for the roof bolter occurs when the roof bolter machine is operated downwind of the continuous miner [Potts et al., 2011; Colinet et al., 2013]. Because of this higher exposure downwind of the continuous miner, the roof bolter is generally limited to working downwind of the miner only once during a production shift"

Jan 1, 2016

By John W. Rozelle, David S. Bolin

INTRODUCTION During the normal course of a mining project, a feasibility study will be prepared that addresses all the aspects of the project including geology and mineral inventories, mining and geo- technical, metallurgical processing, infrastructure, environmental considerations and economic analyses. These studies are prepared for various reasons. Occasionally, a feasibility study will be prepared solely for use within a company as justification for development expenditures, however, these documents are frequently submitted outside the company either to raise funds from financial institutions or from public financing on one of the various securities exchanges. Mineral industry consultants are often called upon to participate in the preparation of feasibility studies or to conduct an independent audit and review of an internally prepared study. As the recoverable mineral resources form the foundation upon which the balance of a feasibility study is based, including the economic analysis of the project, the resource aspect of the study is examined very carefully by financial and securities organizations. The balance of this discussion is directed toward the various geological and resource estimation aspects of feasibility studies that experience has shown to be of particular importance. Much of this discussion will be directed toward open pit gold operations, although the principles are applicable to any type of deposit. 2.0 GEOLOGIC RESPONSIBILITIES IN FEASIBILITY STUDIES The principal geological effort in the preparation of a feasibility study is generally dedicated to the following areas: - Preparation of Geologic Reserve/Resource Estimates - Condemnation of Sites for Facilities, Access Roads, Leach Pads, Waste Dumps and Tailings Disposal - Collection of Geotechnical Data - Provision of Mineralogical and Petrological Data Pertinent to Metallurgical Processing - Selection of Appropriate Bulk Sampling Sites for Collection of Metallurgical Samples Each of these items will be addressed in detail in the following sections. 3.0 RESERVE/RESOURCE ESTIMATION An ore reserve estimate consists of the determination of a volume, or tonnage, and a grade for the deposit. There are numerous cases in the mining industry of projects that have experienced severe difficulties when operational ore grade, tonnage or metallurgical amenability have proven to be deficient compared to predicted estimates. An error in estimation of tonnage generally leads to more long term problems affecting mine life and production schedules. However, a significant error in the estimation of grade, particularly if mined grade is lower than anticipated, can have an immediate, and often disastrous, effect upon a project. The geologic preparation leading to an ore reserve estimate generally follows a logical sequence familiar to

Jan 1, 1987

By J. T. Hanks

Process development is one of the principal tasks required in the course of turning an exploration discovery into a mine. Exploration geologists should have an understanding of the more important metallurgical processes and the test work required for each process. The paper discusses the important metallurgical processes, the test work and sample requirements for each, and the costs and time requirements to accomplish the testing. The limitations of reverse circulation drill samples for metallurgical testing are discussed. The level of process definition required to support engineering studies: scoping, pre-feasibility and feasibility studies are also described.

Jan 1, 1997

By Paul A. Rittenhouse

Its a pleasure to be with you this afternoon and to talk briefly on one of my favorite subjects -- the U.S. sulphur industry. As our Chairman mentioned, I have been associated with the sulphur industry either directly or indirectly for the last twenty years, both on the production side and as a consumer. Sulphur, while unseen and relatively unknown to most people, is like margarine ... that ubiquitous spread ... that is yellow and nearly omnipresent in the industrial world. It is because sulphur, in some form, is required in nearly all aspects of our economy that makes its study so interesting to me as a researcher. An analysis of the sulphur outlook requires examination of such industries as fertilizer, paints and pigments, copper and zinc, uranium, petroleum, chemicals, pulp and paper and textiles - just to name a few. Of course, because its use is so widespread and ever-changing it is difficult to develop and maintain a good understanding of the sulphur industry. It is also a problem to cover the industry in a short discussion and to project its really dynamic nature. Hut, if you will bear with me, I will attempt the task. First of all, let me say that sulphur today is a world commodity and to a large extent moves freely in world trade; nearly a third of the world&apos;s sulphur or something over 15 million tons in 1974 entered international trade. However, today our interest is in the current changing sulphur picture in the U.S., with particular emphasis on the western part of the country.

Jan 1, 1975

By Clinton A. Hollingsworth

The Flotaire Flotation Cell is a simple, efficient hydraulic/pneumatic Flotation Cell that has no moving parts. It is normally used in conjunction with a surfactant (frother) in which case the combination is known as "The Flotaire System". On many ores, metallurgical efficiencies are substantially increased and operating costs reduce. For example, in floating phosphate rock, it is not unusual for BPL recovery to be increased more than 10%, the major increase being due to floating coarse phosphate, up to 14 mesh, and the difficult to float phosphate. Substantial improvements have also been made on coal, mica, vermiculite, kaolin, barite, copper, etc.

Jan 1, 1981

By Andrew M. Wala

The determination of air quantity needed to dilute the exhaust gases to a safe level has to be individually evaluated for particular cases. The diesel powered machines are doing some specific operations in the cyclic order required by the technical process. The dynamics of this process in certain conditions has an essential influence on environmental health conditions in the working area. The main purpose of this paper is to show, using computer simulation, how the movement (dynamic) of diesel vehicles effects environmental health standards and also how to determine the required air quantity for certain conditions

Jan 1, 1983

By J. R. J. Edwards

Jaspilite, a mineral consisting of silica and iron oxide in varying proportions, is one of the host rocks of the high grade ore deposits situated in the Middleback Range of South Australia. As a result of laboratory investigations, a flowsheet was postulated for the beneficiation of jaspilite to produce an acceptable grade product for feeding to blast furnaces, The flowsheet involved the reduction of the hematite in the haspilite to magnetite, the grinding of the reduced product to 95 pct minus 325 mesh Tyler followed by wet magnetic separation, hydroseparation and filtration to yield a magnetite concentrate. Agglomeration of the fine concentrate would then be necessary to meet the physical requirements of blast furnace feed. To prove the postulated flowsheet, to obtain a more accurate estimate of costs and to obtain design data for a commercial installation, a pilot plant was constructed at Whyalla, South Australia.

Jan 1, 1960

By D. L. Lampshire

Biological leaching using native heterotrophic bacteria was studied by the U.S. Bureau of Mines as a means of extracting manganese from a domestic low-grade wad ore. Column heap leaching simulation techniques were employed using molasses as the nutrient source for the bacteria. These column studies were designed to investigate the effects of molasses medium flow rate, concentration, and replacement interval on the extent and rate of manganese extraction. .Results showed that flow rates between 0.41 and 8.1 L/min/m2 had little impact on manganese extraction. The total amount of molasses used did have a direct effect on the extent and rate of manganese extraction. Manganese extractions over 90-pct were obtained in 12 weeks of bioleaching with 2-week medium replacement cycles.

Jan 1, 1993

By J. C. Yingling, V. Badaker, R. J. Sweigard, P. W. Conrad, J. M. Ringe, D. H. Graves

The University of Kentucky has developed reclamation cells at a surface mine in southeastern Kentucky to evaluate the impact of spoil handling (reclamation methods) and compaction alleviation methods on the physical properties of replaced growing media and on tree survival rate. From 1997 through 2001, penetration depth, penetration resistance, bulk density, and tree survival data have been collected at the reclamation cells and correlated to determine the relationships that exist between the soil physical properties at the site and tree survival. Regression models have been developed for each reclamation method evaluated using the collected data to predict tree survival rates on reclaimed surface mined lands as a function of the soil physical properties of the replaced growing media. Procedures have been developed for handling soil/spoil during reclamation that can minimize compaction in the replaced growing media. Procedures have also been developed for alleviating compaction in growing media on reclaimed and orphaned surface mined sites. These procedures, if implemented, will increase the potential for reforestation success. Finally, procedures have been developed for collecting soil physical property data for use in evaluating the suitability of spoil conditions for reforestation.

Jan 1, 2003

By A. E. Ketler

Optical smoke monitoring fills an important gap in ventilation and fire safety: namely monitoring of smoky, low temperature fires where little CO and heat are generated. Smoke monitoring also avoids the nuisance alarms due to diesel exhaust, battery chargers, blasting and welding. The smoke optical density (OD) fire alarm standard specified by MSHA presents an opportunity for improved safety. Experience of actual mine usage of the SmokeBoss*100 is reviewed, with particular regard to effectivity, maintenance and cost.

Jan 1, 1995

By M. Zaske, E. R. Mortensen

"As mine operators continuously look for ways to improve functionality and increase capacity of their facilities, existing process equipment is often pushed to and past its designed limitations. As a result, equipment manufacturers are asked for economical solutions to meet redefined processing needs. Newmont USA (Newmont) in Nevada was faced with such a need in their Carbon-in-Leach (CIL) train. In a collaborative effort between Newmont and Derrick Corporation, tests were conceived to assess the viability of drop in replacement screen using a three dimensional screen panel. The urethane pyramid screen panel was designed to increase flux while maintaining the existing equipment footprint. The test is the end result of an ongoing research and development project that Derrick undertook in an effort to refine and upgrade their urethane screening media. The application of this new screening media is presented for this CIL application along with future plans to implement the technology in trash, safety, carbon dewatering, carbon sizing, and other scalping applications.INTRODUCTION In Spring of 2014, Process Machinery Associates (PMA), Derrick Corporation’s (Derrick) local area representative, met with Newmont USA (Newmont) to discuss the operation of the in tank screens in the carbon in leach (CIL) train at Twin Creeks, near Golconda, Nevada. The process was originally designed for 13,000 +tons per day (tpd) but has been steadily rising since the plant was commissioned and now Newmont requires 16,000 tpd to be processed. The original screens were running at their maximum capacity and Newmont required additional screening capacity to continue the upward trend in production. Physical separation by use of screening is one of mineral processing oldest methods. Screening media can be prone to blinding and pegging and the necessary support structures required for finer apertures result in smaller open areas. Therefore, more screening area generally requires larger panels and therefore larger machines, screening media that doesn’t blind, or a combination of both. In an effort to avoid larger machines, Derrick Corporation had been working on a revolutionary three dimensional panel which would add non blinding screen area in the same footprint of an existing machine. Alpha testing of the new screen panels began at Newmont Mill 2/5 (Carlin, Nevada) in July of 2013 and was still occurring when PMA approached Twin Creeks about beta testing a refined machine and pyramid panel. After presenting the initial results, Twin Creeks determined that an upgraded machine and pyramid panels would be a possible solution to meet production needs. The testing of a machine eliminated the risk of capital costs to Newmont and provided Derrick the opportunity to obtain additional data."

Jan 1, 2015