Search Documents

By R. Q. Honaker

Recent research has shown that enhanced gravity separators provide the opportunity to effectively clean I mm x 37 micron coal. At Southern Illinois University, a detailed experimental program was performed on a continuous Falcon Concentrator, which was found to achieve separations at mass throughput capacity values in excess of 100 tonnes/hour. The apparent particle separation density for I mm x 73 micron coal was about 1.60 with relatively high efficiency (Ep = 0.12). Typical ash and sulfur rejection values of 85% and 70%, respectively, were achieved while recovering 85% of the combustible material. Metallurgical and efficiency data from the evaluation are presented in this publication.

Jan 1, 1998

By P. Zhang

A 1989 FIPR characterization study of the future phosphate resources in Florida showed that MgO would be a problem with both the pebble and concentrate as phosphate mining moves deeper. Since the ratio of concentrate to pebble will become higher and higher in the future, reducing Mg content in the concentrate by a small margin would allow blending of a large portion of the high-dolomite pebble. This research was conducted based on that logic. The following six approaches were tested for reducing MgO content in the flotation concentrate: (1) Adding a dolomite depressant in the rougher flotation step; (2) Dolomite flotation on the rougher concentrate with and without grinding; (3) Dolomite flotation on the cleaner concentrate with and without grinding; (4) Scrubbing the flotation feed; (5) Scrubbing the rougher concentrate; (6) Scrubbing the cleaner concentrate. Successful methods include adding a dolomite depressant in the rougher flotation, dolomite flotation on the cleaner concentrate with grinding, and scrubbing the cleaner concentrate in quartz sand. These techniques could reduce MgO content in the final concentrate by 20-40%. The flotation process could achieve a concentrate with the lowest MgO content, but it is the most expensive approach. Adding a dolomite is inexpensive and easy, but the effect is limited. Overall, scrubbing may be the most promising technology for this purpose.

Feb 23, 2014

By W. Petruk

Mineral liberations that would be obtained by grinding an ore to a specific size can be predicted by analyzing unbroken ore pieces, and mineral liberations in ground ores and mill products can be determined directly by image analysis. Predictions of mineral liberations are made by measuring size distributions and textures of mineral grains by image analysis, and using liberation models. Ground ores and mill products are analyzed to determine the proportion of mineral that is liberated, and the data are used to evaluate mineral behaviour during mineral beneficiation. The liberation data for minerals in a suite of mill products from a circuit are processed by a materials balancing technique to calculate recoveries of minerals in different types of particles throughout the circuit. The liberation-materials balance data define mineral recoveries; define the behaviour of an ore in a concentrator, pilot plant or bench test; and indicate whether recovery improvements are possible and/or feasible.

Jan 1, 1991

By W. C. Hirt

Deposits of ferromanganese crust containing cobalt and nickel occur on the seafloor in the Pacific Ocean near the Hawaiian Islands and Johnston Atoll. This paper describes developmental flotation metallurgy to separate crust from its associated substrate gangue. Important variables in ferromanganese crust flotation include reagent type, aeration rate, conditioning time and agitation intensity, pH, temperature, water type, and feed size distribution. Flotation in seawater of minus 600 ~m (-28 mesh) material assaying 6.2% Mn, 0.2% Co, and 0.13% Ni with diesel fuel-crude tall oil-sulfonate collectors produces concentrates assaying 15% Mn, 0.6% Co, and 0.3% Ni with recoveries of 89-95% while removing 62% of the feed weight.

Jan 1, 1990

By S. Makni, R. E. McIvor

Grate discharges historically outnumbered the overflow type of industrial wet ball mills. However, overflow discharge mills now strongly dominate. In order to understand their comparative advantages and disadvantages, Corem carried out a broad review of this topic. Where the data made it possible, the Functional Performance Equation was used to separate circuit classification from mill grinding effects. Batch tests were conducted in a torque-metered mill at different slurry levels. This paper presents the outcome of these investigations, which is a very strong case for the industry to once again consider grate discharges.

Feb 1, 2023

By J. Snowberger III

Rhenium is a valuable and extremely rare chemical element with unique chemical properties. It is extracted commercially as a byproduct from the processing of molybdenite associated with porphyry copper ores. There is a present interest in recovering rhenium from copper pregnant leach solutions (PLS) produced by copper heap and stockpile leaching. These solutions contain rhenium at very dilute concentrations, typically in the 1 mg/L concentration range. This paper describes laboratory column ion exchange experiments to extract rhenium from these solutions using weakly basic anion exchange resins and actual plant PLS from two operating mines. The dynamic loading and elution behavior of Re on Purolite® A170 and A172 is discussed.

Feb 23, 2014

By J. P. Ramsey

This is a description of the efforts of a research project intended to demonstrate methods of alleviating pollution from coal mine refuse piles and slurry lagoons. These are mainly derelict barren sites. Some are burning and some are vulnerable to wind erosion which causes air pollution. Some occupy valuable land near metropolitan areas. They are an integral part of the landscape of the Appalachian and Midwestern Coal Fields. They are important in the light of growing civic awareness of the great general problem of waste disposal and environmental improvement. In the V-shaped valleys of the Pocahontas Region, they continue to be piled higher and higher. In flatter topography, they tend to form broad, flat ridges. Some contain more metal forms than others and some have a minimum of metal, but weather to a fine talc, which chokes streams with a fine particle suspension. Most are burning or have burned, but burning or weathering, most all are sources of pollution to the atmosphere and to adjacent waterways. This demonstration project is being carried out at an abandoned mine near the town of Du Quoin in southern Illinois. It is jointly sponsored by the Truax-Traer Division of Consolidation Coal Company and by the Federal Water Pollution Control Administration of the Department of the Interior. The site area is a refuse pile and slurry lagoon, each of fifty acres. It is hoped that basic data from this study will be generally applicable to other sites and will provide a basis for rational and efficient engineering design of future reclamation projects. Most refuse piles have extremely long term capabilities to produce highly potent acidogenic oxidation products typifying the more serious aspects of acid mine drainage contamination. Numerous sites remain where the abandoned mine no longer discharges acid waters, but its associated refuse pile continues to generate significant quantities of acid and other oxidation products even after many years.

Jan 1, 1969

By W. F. Riggs

INTRODUCTION Flotation equipment is becoming more definitive in design as well as greater in dimension. The last ten years have witnessed the implementation of large flotation cells ranging in size from 28 to 85 cubic meters. However, small plants still operate with cells as small as 3 cubic meters. These changes have increased the operational sensitivity of the flotation system to the chemical reagents used. No scientific study has been undertaken to develop the relationship between the size of equipment and the response of reagents in the flotation system. Hence, this article is an attempt to present several observations from past experience for the purpose of stimulating future research in an area previously ignored and perhaps subsequently not used to advantage. CONVENTIONAL FLOTATION Recent advances in conventional flotation cell design have been made in two areas: a. Flotation cells are becoming larger, and b. Basic design of flotation cells has changed. They can be classified into two types: deep cell and shallow draft cell. Size and design changes of flotation cells have a greater effect on frother performance than on the performance of other chemical reagents. Hence, the discussion in the following sections is restricted to the impact of frothers in the flotation system. Flotation Cell Size The advent of increasing flotation cell size has resulted in the increase of frother consumption. There appears to be a correlation between reduced horsepower (kilowatt) consumption and increased frother consumption per ton of ore processed in the circuit. This is more prevalent when the frother chemistry remains unchanged. Another reason for increased frother consumption is the increased distance between the rotating central shaft and the lip of the cell for larger flotation machines. Increasing this distance results in increased surface area corresponding to the larger cell size. Reduced power input per ton combined with the need for longer, stronger load support of the froth bubble as a result of increasing cell size has resulted in the development of a new series of stronger and more persistent frothers. By the same token, these newer, stronger frothers are difficult to control when applied to the smaller cells. This is true even at lower dosages because the break point between too much frother and not enough frother for optimum metallurgy is normally very narrow. This problem is often exaggerated when operators have established an optimum setting for pulp level and air for the particular frother in use. Generally, the tendency is to operate the flotation cells simply by adjusting frother dosage. The increase in frother strength to accommodate the large cells often results in the realization, after a retrofit, that the existing pump box or sump which is still handling the same volume of concentrate is no longer adequate in size. Flotation Cell Design The two most common flotation cell designs installed during the past ten years are the deep cell and the shallow draft cell. The deep cell provides for complete mixing of air and pulp at the bottom of the cell. The shallow draft cell does all the mixing/pumping in the bottom haft of the cell whereas the mixing of the air is performed further up the shaft and is brought into contact with the pulp midway up the vortex. There are many preferences for one or the other. It is the author's contention that both designs have very valid concepts and must simply be suited to the particular situation as required by the operator. The following comments are subjective observations which should be explored in greater detail. The deep cell mixes both air and pulp together at the bottom of the cell requiring a full depth ascending of the homogenized air to the surface to form the froth layer. This design, in combination with charged air, provides for good concentrate grade control under adverse conditions of selectivity, especially when faced with a fine grind and a slime-laden gangue. A selective frother can be applied without a competitive loss in recovery. One of the conditions for good selectivity in this environment is operating at medium pulp solids concentration in the range of twenty-six to thirty-four per cent (26-34%). When a higher solids concentration is used in combination with a coarse grind, it becomes difficult to maintain the same recovery with a selective frother due to higher pulp viscosity. This condition sometimes results in an unacceptable coalescence of the air bubbles as they ascend the full height of the deep cell. The increased pulp viscosity at higher solids concentration can also retard the flotation kinetics. The combination of decreased surface area of dispersed air and slower kinetics can result in reduced recovery causing coarse particles to continue to drop

Jan 1, 1989

By Edward L. Mooney

In the, West, walking draglines often offer the least cost method of uncovering coal for surface mines. However, with each of these machines costing millions of dollars, a good deal of analysis can be justified by the potenial savings or, conversely, costs associated with the choice of a machine. This has resulted in the recent development of a number of computerized models for dragline selection and pit design. One of the earliest reported models for this purpose was developed by Dunlap and Jacobs (1). Later, Rumfeldt described the computer approach to sizing stripping draglines given the required production rate and mine site parameters (2). This basic approach is probably still the most widely used with models for more complicated mining methods reported by Stefanko, Tomica, Finch, as well as others (3,4,5). furthermore, detailed simulation models useful in this regard have been developed by McDonnell Douglas and Fluor, Utah (6,7)

Jan 1, 1982

By J. C. Harrison

Eldorado Gold Corporation of Vancouver, B.C. owns and operates three gold mines. The Sao Bento underground gold mine in Minas Gerais State, Brazil produced 105,907 ounces in 1997. The La Colorada and La Trinidad open pit, heap leach mines in Mexico produced over 83,000 ounces in 1997. With a deteriorating gold market plaguing the industry throughout 1997 Eldorado had to take critical measures at each mine to enhance gold production while lowering cash operating costs. Each mine had its own unique problems to confront. This case study will discuss three distinct courses of action taken at the three mine sites.

Jan 1, 1999

By R. K. Mehta, U. Cetin

The Nevada Test Site is located approximately 100 km (65 miles) northwest of Las Vegas, NV. The site was primarily used by the Department of Energy for the field testing of nuclear weapons and has been contaminated by several million cubic feet of low-level radioactive wastes, heavy metals, explosive materials, and volatile and nonvolatile organics. The transportation and leaching of these contaminants are creating serious environmental problems. The purpose of this study is to examine pozzolan, a natural alumina-silicate mineral, as a possible replacement for the existing impermeable clay barriers. In the first phase of this study, radionuclide sorption characteristics of pozzolan were investigated. This paper presents the results of the adsorption tests for the target radionuclides.

Jan 1, 2000

By David L. Martin

This paper discusses the development of a SLAM II* simulation model with imbedded optimization modules designed M evaluate mineral exploration and exploitation strategies. The model traces through a sequential exploration program, evaluating each deposit site based upon geologic information and potential profitability of the site. At a specified time during the simulation, a new production plan is developed for currently producing deposits which takes into account the planning horizon and deposits which are currently being explored. Potential uses of the model by geologists, engineers, and management decision makers include setting corporate objectives and policies on exploration and production. The model is also useful for testing past decisions to evaluate decision making criteria and evaluating mineral deposit profit potential.

Jan 1, 1983

By C. Hilton

Arch Coal Inc. has implemented and sustained Best Practices at its four western mines through utilizing foremen in ongoing time studies. A prime benefit is the unique opportunity provided to front line supervisors. To date, 48 supervisors have participated in this program. Each quarter a new team is assembled with members from each operation. During three month blocks the supervisors conduct studies at each mine and identify best practices to implement at their own mine. Ongoing Best Practice and Action Item lists are reviewed each study. Mine management edits, prioritizes and monitors the completion of the proposed action items.

Jan 1, 2010

By John E. Edkins

Metal sulfides, chiefly pyrite and mFnor sphalerlte zssociated with che Herrin (No. 6) coal member of the Pennsylvania Carbondale Formation, have been concentrated in a coal refuse deposit in southern Illinois. Oxidation of pyrite has produced highly acid waters with high concentrations of iron, zinc (up to 200 parts per million) and toxic trace elements that have leached downward to a water system perched on glacial drift. Chemical, petrographic, low-temperature ashing and x-ray diffraction were performed on cores. The data show that economic recovery of zinc and other trace metals is unlikely at this site. Energy (coal) recovery at the Superior Washer site is possible if resultant environmental problems are considered in the planning.

Jan 1, 1981

By M. C. Rockwell

There are approximately 1,800,000 t of discarded dolomitic-limestone tailings from the Gays River lead/zinc mining operation in Nova Scotia. Neutralization effectiveness similar to an agricultural grade limestone and low contents of residual metals make the tailings a suitable source' of soil conditioner material for the local market. However, the fine particle size, 98% passing 147µm, and a high moisture content make their handling and application difficult. Agglomeration of the tailings into relatively small hard pellets was investigated and difficul¬ties were overcome. Pellets with a range of pH values and various amounts of soil nutrients and moisture content less than 10% were obtained, from tailings containing 20% initial moisture, through the addition of less than 15% selected materials.

Jan 1, 1985

By M. Stuart

The copper-silver-mercury orebody of Gortdrum Mines (Ireland) Limited is located 3 miles north of the town of Tipperary in the Republic of Ireland. A drilling programme from 1964 to 1966 delineated an ore¬body of 4.19 million tons of copper ore assaying 1.19% Cu and 0.75 ozs per ton Ag, which could be mined from an open pit. Testwork having shown that the ore was amenable to conventional flotation techniques, it was decided to build a concentrator of 500,000 tons ore per year capacity. Stripping of the open pit commenced in 1966 and in the autumn of 1967 the concentrator started up. The first shipments of concentrates were made to the smelter in Europe in late 1967. In the spring of the following year, word was received from the smelter that these early shipments contained between 1% and 2% Hg, and that the smelter could not accept further shipments of this quality.

Jan 1, 1973

By A. Arik

Reliable ore reserve estimates for deposits with highly skewed grade disributions are difficult tasks to perform. Although some recent geostatistical techniques are available to handle problems with these estimations, ordinary kriging or conventional interpolation methods are still widely used to estimate the ore reserves for such deposits. The estimation results can be very sensitive to the search parameters used during the interpolation of grades with these methods. This paper compares the ore reserve estimates from ordinary kriging using several cases in which certain search parameters are varied. The comparisons are extended to different mineralizations to show the changing effects of these parameters.

Jan 1, 1990

By George S. Koch

We evaluate the exploration effort by diamond drilling for zinc in central Tennessee and southern Kentucky through a statistical analysis comparing the Middle Tennessee district with the older Tri-State and Upper Mississippi Valley districts. All of the ore deposits are of the Mississippi Valley type and are similar geologically. Through statistical analyses we attempt to answer these questions: Had the drilling density in the Middle Tennessee district been applied to the Tri-State district, how much of the ore in the Tri-State would have been discovered? Had this drilling been done in the Upper Mississippi Valley district, how much of the ore in that district would have been found? Which of these two older districts does Middle Tennessee more closely resemble in intensity of zinc mineralization? Is more drilling warranted in the Middle Tennessee district? Our data base includes tonnage and area distributions of ore deposits in the Tri-State dis¬trict, sizes of ore bodies and probabilities of their recognition in the three districts, and data for the Elmwood mine in the Middle Tennessee district. Our statistical analysis considers the consequences of drilling holes in the three districts on square grids at coarse, intermediate, and fine spacings. We conclude that the drilling pattern assumed for Middle Tennessee would have found some but not all of the ore in the two older districts. We believe that in intensity of mineralization Middle Tennessee more closely resembles the Tri-State than the Upper Mississippi Valley district, and that more drilling is warranted in the Middle Tennessee district.

Jan 1, 1979

By P. N. Psarropoulos

During many strong earthquakes in the past, a significant number of tailings dams failures has been recorded, leading in some cases to human life losses. However, over the last decades, seismic design of tailings dams has drawn much attention mainly due to the high environmental hazard. Although the stability of such geostructures under dynamic loading is mainly related to their liquefaction potential, there exist several technical issues that have not been adequately investigated. One of these issues is the impact of local site conditions on the dynamic earthquake stresses developed, and therefore on the inertial instability of these dams. Based on the models examined in the first part of the present study (Stability of Tailings Dams ? Part I: Static Loading), two-dimensional numerical simulations are performed in order to examine the effects of local site conditions in the dynamic response of tailings dams. Imposing dynamic loading via characteristic pulses and real earthquake records, the most commonly used types of construction methods are studied at their final stage. Emphasis is given on the special characteristics of the ground motion, while the material nonlinearity of both soil and tailings is taken into account by an equivalent-linear procedure. The results obtained indicate that local site conditions may have a significant impact on the seismic response of a tailings dam.

Jan 1, 2005

By V. K. Gupta

The experimental results of some wet batch and continuous grinding experiments carried out in a 40 x 40 cm grate discharge ball mill have been analyzed for the variation of the grinding rate parameters, Si, with various operating conditions using a linearized population balance model. The wet grinding tests were carried out under conditions which were very similar to those encountered in the actual practice in plant operation. Well distributed -4 and -20 mesh feeds of two complex pyritic ores were used. The volume-percent solids in the pulp ranged from 30-40, the particle load from 5-8 kg, and the solids feed rate from 70-1 10 kg/hr.

Jan 1, 1981