Search Documents

By Brett P. Spigarelli

To meet the growing need for CO2 capture and storage technology, Michigan Technological University is researching CO2 capture and storage using alkali solutions1. Without implementing emission controls, world energy emissions will rise from 29.7 billion t in 2007 to 42.4 billion t in 2035. The first objective of the project was to determine the optimal amount of alkali in solution for CO2 absorption. This was accomplished using theoretical equilibrium calculations and experimental absorption data for alkali solutions of 1, 2, 3, 4 and 5 weight %. As the % alkali in solution increased, so, too, did the ionic strength of the solution. Theoretical calculations took into account the effect increasing ionic strength will have on the solubility of gaseous CO2. The calculations assumed negligible formation of H2CO3, constant temperature and constant pressure. In the experimental setup, a 16% CO2 /balance air gas mixture was bubbled through an Erlenmeyer flask filled with an alkali solution. The gas exiting the flask was fed to a gas analyzer to record the % CO2 in the exhaust gas stream. The % CO2 absorbed was taken as the % CO2 in the exhaust gas minus the % CO2 in the feed. Theoretical calculations found that as the % alkali in solution increases, the solubility of CO2 decreases. This was verified by experimental data, which found that a 2% alkali solution, by weight, was the ideal solution for CO2 absorption. Current research is focused on using the 2% alkali solution for permanent storage of CO2 via mineral carbonation to produce a value-added product.

May 1, 2012

By Rudolf E. Pfister

One of the Swiss transalpine highways includes two remarkable tunnels: the 16.3 km long Gotthard Road Tunnel and the 9.3 km long twin tube Seelisberg Tunnel, both presently under construction. Large diameter shafts up to 900 m long are required for ventilation. Excavation techniques for rock formations ranging from loose sedimentary rock to granite and very hard siliceous limestone were carefully evaluated. The methods finally applied include excavation of shafts in hard rock, conventional drilling and blasting, excavation by ripper-tooth excavator ("Big John") in marlstone, shield protected heading in loose material and soft rock, and tunnel and shaft lining, both by poured concrete and by prefabricated elements. A critical review of the success of these methods can now be made after a five year construction period.

Jan 1, 1976

By R. W. Sayers

The Duval Corporation porphyry copper deposits at Copper Canyon and Copper Basin, though widely separated, form an economic unit requiring integrated exploitation. Contrasts in mineralization, host rocks, and mode of occurrence present unique mining and milling problems. Mixed oxide-sulfide ore is treated in extensive dump leaching facilities in both areas. Complex copper-gold-silver ore is treated in a 4,000 tpd mill at Copper Canyon. In both areas, hypogene metallization occurs within large aureoles of metamorphism and hydrothermal alteration related to quartz monzonite intrusions of mid-Tertiary age. Supergene processes further altered the rocks and enriched the hypogene protore. At Copper Canyon, hypogene copper and iron sulfides with gold and silver occur in fractures, as partial replacement of favorable beds, and as disseminations in Paleozoic sedimentary rocks. The lower part of the Pennsylvanian Battle Formation was a particularly favorable host. Metallization occurs to a lesser extent in quartz monzonite. Metal zoning is well developed. The deposits at Copper Basin consist principally of supergene copper minerals in arenites of the Cambrian Harmony Formation. Oxidation of hypogene copper and iron sulfides in tactite zones has formed at least two commercial deposits; intersections of fractures with favorable beds exerted important ore controls.

Jan 1, 1968

By Daniel J. Turk, William R. Banning, John Paterson, Thomas J. Weitz, Michael L. Clark

Introduction Pegasus Gold's Montana Tunnels mine is a large surface gold, silver, lead, and zinc mine located 37 km (23 miles) south of Helena in southwestern Montana. Milling operations commenced in late March 1987. The concentrator achieved full production in May that year after undergo¬ing several modifications and improvements. Production for 1988 is projected to be 2.48 t ,80,000 oz) of gold, 34.2 t (1.1 million oz) of silver, along with 8.5 kt (9400 st) of lead, and 22.6 kt (25,000 st) of zinc from lead and zinc concentrates. Mill throughput currently averages 11.7 kt/d (12,900 stpd), compared to the origi¬nally designed capacity of 11.3 kt/d (12,500 stpd). Cash production costs, net of bypro¬duct revenues for the third quarter 1988, were below $3.20/g ($100 per oz). The introduction of ore to the concen¬trator marked the culmination of 12 years ex¬ploration, evaluation, and development. Initial milling operations encountered diffi¬culties with the circuit as designed. As a result, several modifications and improve¬ments were made to the plant. This article is intended to assist other companies developing projects of this type and complexity. It discusses the mine's de¬velopment from feasibility and construction through start-up. The operation, as it exists today, is reviewed including the modifica¬tions and improvements made since start-up. History The mine is situated in Jefferson County, MT within the historic Corbin-Wickes min¬ing district. Underground mining began in 1864 and flourished until the early 1900s. Between 1864 and 1900 the vein deposits in the district produced about $41 million dol¬lars worth of lead and silver ores containing subordinate amounts of zinc, copper, and gold. At various times, three smelters were operated in the area.

Jan 1, 1989

By Basar Arioglu, Jaeung Kim, Mehmet Öztürk, Jinmoo Lee, Dongho Lee, Taek-Kon Kim

"Istanbul Strait Road Tube Crossing Project (Eurasia Tunnel) includes 3.34 km of a bored double-deck tunnel under the Bosphorus Strait, at a maximum depth of 106 m from the sea level, and 1 km of twin NATM tunnels on the Asian side. The region’s variable geology, hydrology and propensity for seismic activity, combined with high water pressure and large-diameter/double-deck tunnel configuration, make the Eurasia Tunnel one of today’s most challenging and complex projects under construction. Due to the site’s proximity to the active North Anatolian Fault, the tunnel is designed to withstand a 7.5 magnitude earthquake. The tunnel penetrates through both the Trakya bedrock (on both European and Asian sides) and the alluvial sediments at the bottom of the channel. The tunnel is designed to accommodate differential displacements by introducing seismic/flexible joints at proper locations at the transition zones between rock and soft soils. Tunnel fire is also a significant design consideration for undersea tunnel due to that the rubber protecting it in close proximity of the seismic joint should resist a fire for long term safety and durability. This paper mainly focuses on the design for method of tunnel response analysis in transverse and longitudinal direction against seismic demands relating with the seismic joints. INTRODUCTION Istanbul Strait Road Tube Crossing Project (Eurasia Tunnel) will build and operate a roadway tunnel under the Borphorus connecting Kazlicesme on the European side and Goztepe on the Asian side, to provide additional road-access across the Strait and consist of three main parts as shown in Figure 1."

Jan 1, 2016

By James Yancik

The Howe Coal Company located in Leflore County, Oklahoma is mining the Oklahoma Lower Hartshorne Coal bed which ranges in thickness from 38" to 42" and dips approximately 7 degrees to the Northeast. The Lower Hartshorne bed lies within the Hartshorne sandstone in Oklahoma but is as much as 60 feet above this sandstone formation in Arkansas. This coal bed extends throughout the Arkansas Oklahoma coal basin, which is about 50 miles wide and 180 miles long and progresses from a semi anthracite in Arkansas to a low-volatile coal in the eastern part of the Oklahoma to a high-volatile coal in the western area. The Howe Mine #1 in the eastern area is mining a low-volatile bituminous coal which has been used as metallurgical coal since the early 1900's as evidence of Bee-hive coke ovens still remain near the town Howe, a few miles northwest of the mine site. The Howe Mine is the first mine in the area to use modern mining equipment, however, numerous punch mines have been worked along the outcrop south of the mine site dating from 1900 with the last closing in 1965. The coal characteristics of the Lower Hartshorne rival the Pocahontas seam in chemistry and coking qualities. This paper will be concerned with the preparation of the coal for the Japanese steel market. The three man crew necessary to operate the plant are the operator, the helper, and the equipment operator needed to feed the raw coal hopper. An additional equipment operator is available on the day shift for coal loading and moving the clean coal to the storage pile as the area under the clean coal belt is only large enough for 1 shifts production. We are at present running the plant on a 2 shift per day basis.

Jan 1, 1969

By Charles K. Presley

This paper deals with drilling large diameter shafts for the mining and construction industry with diameters in excess of 3 feet to more than 20 feet in diameter. It discusses appropriate applications of the rotary drill method, linings for large diameter shafts, circulation systems,, and the limitations of the method. Each specific rotary drill method is determined by the geology of the area, the depth to be drilled and the formation fluids encountered. Shaft lining or casing must be improved to result in lighter weight, higher strength and lower cost. All phases of rotary drilling equipment must be improved to drill shafts in excess of 10 feet in diameter. As these goals are reached, more shafts of large diameter will be drilled by the rotary method for the mining and construction industry.

Jan 1, 1967

By d&apos, J. A. Oliveira, A. K. L. Resende, L. F. G. Assumpção, J. D. Neto

Kaolin samples from Rio Capim Resources were treated in conventional and superconducting magnetic separators to study the main variables that influence the impurity removal process. Two coating clays and a delaminated clay were tested. The variables studied were retention time (cross-sectional velocity), magnetic-field intensity and matrix type. The feed brightness ranged, from 84.7% to 87.6% ISO, for the coating clays and ranged from 80.7% to 85.4% ISO for the delaminated clay. Using a conventional magnetic separator with an applied, field of 1.5 to 2.0 T (tesla), the brightness values were higher than 88% ISO for the unleached coating claw products and were higher than 87% ISO for the unleached delaminated product. With a maximum field intensity in the superconducting machine of 5.0T unleached brightness values higher than 88.5 % ISO were attained for both coating and delaminated clays.

Jan 1, 1997

By A. A. Sobek

Controlled release systems delivering the required concentration of an effective bactericide over an extended time period have been developed by The BFGoodrich Company's ProMac® Systems group. The ProMac system is site-specific and includes a four-step approach to controlling acid mine drainage (AMD): (1) Diagnosing the problem, (2) Prescribing the treatment, (3) Supervising the application of controlled release bactericides, and (4) Honitoring the success of applied treatment. The success of the ProMac system is evidenced by improved water quality, healthy vegetation, a reduction in levels of acidophilic thiobacillus, and a corresponding increase in population of beneficial microorganisms.

Jan 1, 1986

By William Gleason

"Technology of all forms has experienced exponential growth in recent years, and there is no sign of it slowing down. This growth has presented amazing opportunity and significant challenges in nearly every aspect of daily life. Some of these changes are seen and experienced every day as we turn to our smart phones, tablets and smart watches to help with us with everything from directions to the store to managing our health. And other technological growth takes place far away from the public view but can have as much of an impact on our daily life as does shopping at Amazon or connecting with friends on social media.At the “THRIVE 2018, Innovations Advancing Mining” conference presented by SME on Sept. 27 at the Sheraton Pittsburgh Hotel at Station Square in Pittsburgh, PA, the focus was on innovation and how it affects the global mining industry.More than 100 people were on hand for the inaugural event, and they were treated to a unique program that focused on the cutting-edge innovations that will carry the mining industry into the future while increasing safety and productivity along the way.2018 SME President Barbara Arnold was the driving force behind the conference and put together the technical program with a focus on innovation through the entire mining life cycle and into the future. Talks ranged from more efficient and safer ways to extract minerals to some of the most advanced end uses of minerals and metals, including the use of 3D printing to create precision parts for machines and humans from advanced metal alloys.“We need to adapt new technologies to our industry and develop additional technologies as we provide materials and metals for infrastructure and energy development in the United States, around the globe, and to the Moon and beyond,” Arnold told Mining Engineering. “Our inaugural THRIVE conference sets the stage for these innovations to be applied and to continue to be developed. Our mining industry can only continue to thrive with these advances.”"

Jan 11, 2018

By Justine Ealy, Daniel Yang, Christina Foster

Maintaining stable high walls can be a challenging task. Complex geological and structural features, alteration zones, rock mass properties, and hydrogeological conditions must be well understood to design a safe mining environment. Economic considerations must also be taken into account as the mine operator must provide ore deliveries and protect reserves. However, even when good engineering practices are followed, and proper blasting and mining techniques are implemented, slope movements may still occur. When these slope instabilities are minor, the mine is often able to continue operations with minimal impacts on safety or production. When these occurrences are excessive and coupled with high rates of movement, a robust monitoring system is crucial to continuing mining activities while protecting personnel. This paper summarizes the approach an open pit mine in Nevada took as excessive and rapid high-wall movement was experienced in an integral area. Creative mining approaches, combined with slope monitoring radar technology, were utilized to maintain safe and successful mining activities despite active movement that exceeded an average velocity of 30 inches per day.

Feb 1, 2024

By Dr. Jagdish C. Agarwal

Kennecott Copper Corporation has developed a new hydrometallurgical process for extracting nickel, copper, cobalt and molybdenum from maganese nodules. This process (KCC Cuprion Process) utilizes a reduction leach operating at atmospheric pressure in the temperature range of 45 C to 50 C and has been successfully demonstrated in a continuous pilot plant processing 800 lbs of nodule ore per day. The chemistry, basic flow sheet and operating characteristics are presented and discussed.

Jan 1, 1978

By William M. Turner

Thermonics is a methodology of ground-water flow system analysis based upon the distribution of heat within the subsurface as influenced by moving ground water. Thermonics is based upon the Stallman Equation 1 (1) which describes the simultaneous transfer of heat through a porous medium which contains moving ground water. The Stallman Equation is:

Jan 1, 1980

By Albert J. Kritscher

The Similkameen Copper Project located near Princeton, British Columbia, is operated by the Similkameen Mining Company Limited, a wholly-owned subsidiary of Newmont Mining Company. The orebodies for this project are located on both sides of the Similkameen River for which the project is named. The project involves the processing of an average of 15,000 STPD of andesitic ore, mineralized largely with Chalcopyrite, at an overall plant availability rating of 90 percent. Project life is nominally 15 years. Design for the plant and its ancillary facilities was undertaken by Bechtel Corporation with procurement and construction management by Canadian Bechtel Limited. Construction began in June 1970 and first ore was introduced into process in March 1972. This paper concerns itself only with the project tailing system. The processing plant is located on a bench of glacial stream gravels which overlooks the river canyon. This site represented the only relatively flat area of sufficient size to accomodate processing facilities near to the ore- bodies. Reference is made to Figs. 1 and 2 showing the relationship of project features in plan and profile.

Jan 1, 1973

By N. B. Aughenbaugh

A study was made to determine those petrographic parameters that are correlative with carbonate-aggregate quality as indicated by the Los Angeles abrasion and absorption tests. Samples collected at 28 sites in northern and eastern Indiana were analyzed petrographically, chiefly for void content, grain size, grain-size variation, grain shape, and grain interlock. Most of the sampled sites are in the belt of Silurian rocks of east-central and north- western Indiana. Though a few sites lie outside this belt, most of these have only a thin Devonian section above the Silurian. Three sites are non-Silurian and are included for comparison. Most of the samples studied are from Middle and Upper Silurian units. Both biohermal and nonbiohermal facies are included. The biohermal rocks are typically dense but vugular, finely crystalline granular dolomite. Nonbiohermal facies are porous, medium to coarsely crystalline, granular dolomite with dolomite rhombs The Los Angeles abrasion losses ranged from 20 to 46 per cent, the rocks in the eastern part of the state showing the higher values. Absorption tests indicate the same general quality trend. Comparison of petrographic studies with Los Angeles abrasion- and absorption-test results indicate the following correlations. (1) As per, cent of voids increases, quality decreases. (2) As average grain size increases, quality decreases. (3) Variations from mean grain size appear to have no effect on the quality. (4) As angularity and roughness of the grains increase, quality increases. (5) As grain-to-grain interlock increases, quality increases. Variations in the calcium-magnesium ratio have no apparent effect on aggregate quality, except as they affect the texture.

Jan 1, 1966

By N. S. Aouad

"Gaseous explosions are one of the most hazardous incidents in process and mining industries. Experimental research in this area is shown to be high risk and expensive. Computational Fluid Dynamics (CFD) techniques are reasonable alternatives to experiments; specifically when testing large scale gaseous explosions such as methane explosion in underground mines. The dimensions of a confined space where explosions could occur vary significantly. Thus, the scaling effect on explosion parameters is worth to be investigated using CFD tools. In this research paper, the impact of scaling on the explosion overpressures is investigated by employing two scaling factors. These two factors are the Gas-fill Length scaling factor (FLSF) and the Hydraulic Diameter scaling factor (HDSF). The combinations of eight HDSFs (1, 2, 4, 8, 16, 32, 64, and 100) and five HDSFs (0.5, 1, 2, 4, and 8) will cover a wide range of space dimensions where flammable gas could accumulate. Experiments were conducted to evaluate the selected premixed combustion and turbulence models. Large Eddy Simulation (LES) turbulence model was used because it shows accuracy compared to the widely used Reynolds’ averaged models for the scenarios investigated in the experiments. Researchers also simulated methane explosions in both deflagration and detonation regimes using different numerical schemes. Three major conclusions can be drawn from the simulation results. (1) The overpressure increases with both FLSF and HDSF within the deflagration regime; (2) in an explosion duct with length to diameter ratio greater than 54, detonation is more likely to be triggered for stoichiometric methane/air mixture; (3) overpressure increases as an increment hydraulic diameter of a geometry within deflagration regime. INTRODUCTION The most typical category of gaseous explosion accidents is methane explosion accidents in the mining industry. It normally leads to significant economic loss and massive amount of casualties (McPherson, 1993). It could occur in unconfined spaces, such as combustion due to flammable gas leakage, as well as confined spaces, such as inner-combustion in process equipment and methane explosions in airways of underground mines. Gaseous explosions in confined spaces are more intensive compared to unconfined spaces provided that the total energy of explosives is the same. In addition, explosion characteristics are also affected by the geometry of a selected confined space. The size of confined spaces commonly encountered in process and mining industries could differ as much as an order of four (Catlin & Johnson, 1992). A better understanding of the scaling effect on gaseous explosions could contribute to explosion mitigation and prevent operation activities within high risk regions. This research paper has investigated this scaling effect and its impact on explosion propagation. The approach to investigate explosions is either experimental or numerical. Large scale explosion experiments are often costly and dangerous (Catlin, 1991; Zhang, Pang, & Zhang, 2011). Lab scale experiments and numerical methods are common alternatives. However, it is not yet clear if the findings in lab scale experiments can be used to represent the explosion characteristics or not. On the other hand, CFD modeling has been used to simulate chemical combustions and, thus, can be used to evaluate the scaling effects in methane explosions."

Jan 1, 2015

By William Gleason

"The mining industry tends to focus on very large numbers, whether it’s talking in terms of size of deposits, tons of material mined, the equipment used or the dollars spent. The numbers associated with mining projects are often in the hundreds of millions, but sometimes it’s the little things that can have the biggest impact.Take, for example, the Rosemont Copper Project in Arizona. Owned by HudBay Minerals, the Rosemont Copper project, when in production, is expected to be one of the largest copper mines in the United States, accounting for about 10 percent of total copper production with annual production expected to be 110 Mt/a (243 million lbs/year). However, the project is currently mired in a years-long permitting process. At the 2017 SME Arizona Conference in Tucson, AZ, Kathy Arnold, director of environmental and regulatory affairs for Hudbay Minerals, spoke about the project and the efforts to get it into production.She opened her presentation with the unfortunate news that her 2017 presentation would not be that much different than the 2016, 2015 or 2014 presentations she gave to the same conference. That’s because, as of Dec. 4, 2017, the project had been in the permitting process for 3,797 days, more than 10 years. The process began when Rosemont submitted its initial mine plan in 2006 and a revised one in 2017. The official start to Rosemont Copper’s National Environmental Policy Act (NEPA) started in 2008.In June 2017, the project received its Final Record of Decision from the U.S. Forest Service, moving it a step closer to production. Yet it still faces stiff opposition from opponents while it works to secure the Clean Water Act Permit from the U.S. Army Corps of Engineers and to complete its final mine plan of operations.In her presentation, Arnold said the long process taught her many lessons, including approaching things with a different mindset. More than 130 pages worth of public comments have been collected over the years. The concerns expressed range from lighting issues to pavement to preserving land for a jaguar that was spotted on the property and named El Jefe.“A lot of things that people worry about seem to be small things, but we had to have a different mindset and be open-minded to the concerns,” Arnold said. “That is the commitment we made.”"

Jan 1, 2018

By A. G. Ulsoy

In recent years there has been an Increasing Interest In the application of automatic control theory to mineral processing systems, and numerous applications of mineral process control have appeared in the literature. A general approach to the synthesis of mineral process control systems is presented. The first phase of the control system design consists of specifying the control objectives, process variables and their interactions; these topics will be discussed with specific reference to mineral processing. The second phase Is con¬cerned with selection of control strategies algorithms, instrumenta¬tion, and other components of the control system and is discussed at length. These concepts are then illustrated by a flotation control case study.

Jan 1, 1981

By Agus Sasmito, SRIVATSAN JAYARAMAN SRIDHARAN, Akash Adhikari, Purushotham Tukkaraja

The amount of toxic fumes produced during blasting operation depends on the types of explosives used, product formulation, degree of confinement, conditions of use, and reactivity of the explosives with the host rock. Ammonium nitrate and fuel oil (ANFO) is still the explosive of choice due to its lower price and ease of use/loading. If not properly monitored and controlled, toxic fumes produced from blasting operations can have serious health hazards [1]. This paper presents a novel technique developed to track trapped fumes during a development blasting.

Aug 1, 2022

By R. Jin

Fine coal flotation using gaseous carbon dioxide has demonstrated the potential for producing superclean coal. The success of this new flotation .procedure is attributed to the coal's high adsorption potential for CO2. To understand the nature of gas-phase CO2 adsorption at the coal surface, in-situ FTIR spectroscopy in a controlled-environment chamber with an ultravacuum sys-tem has been used and the results are discussed in view of other experimental results from differential scanning calorimetry. It has been found that specifically adsorbed CO2 molecules at the coal surface are polarized and have a characteristic doublet at 2336 and 2361 cm-1. Two adsorption states have been proposed to account for the doublet observed from in-situ FTIR spectroscopy measurements. It is believed that the band at 2336 cm-1 originates from the activated site adsorption of CO2 and that the band at 2361 cm-1 arises due to the molecular aggregation of CO2 within the coal pores.

Jan 1, 1988