Search Documents

By Mohamed Gamal, Bill Zietlow

"In oil fields that have been depleted with conventional surface oil wells but still contain significant reserves, an extraction alternative that has been constructed recently consists of a drilling gallery below the oil-bearing formation at the bottom of a 1,200-ft deep shaft where upward sloping wells are being drilled to allow oil collection by gravity. The gallery is 92-ft diameter with a flat ceiling supported by rock bolts and shotcrete structurally connected to the shaft liner, which doubles as a large tension support element. A special excavation sequence was implemented for the gallery to maximize arching in the stress above the large diameter gallery. The gallery was located in competent sandstone, constructed with sequential excavation methods, and designed with a 3D finite element model. Special consideration was given to optimizing the gallery location to take advantage of the geology for construction and support while giving good positioning to the well drilling equipment. BACKGROUND Brierley Associates was contracted to provide both design and construction management services for an approximately 1,165-ft deep, 18-ft excavated diameter vertical shaft that opens to a 92-ft diameter flat roof gallery. The geotechnical data for the site was based on information available from literature and from data obtained during core drilling and from in-situ testing in a 1250-ft deep borehole. Wire line coring was conducted using a HQ, 10-ft long core barrel with a mud-rotary drilling method through sedimentary bedrock. The geometry of the shaft and the bottom gallery is shown in Figure 1(a). GEOLOGIC SETTING AND STRUCTURAL GEOLOGY The stratigraphy at the site includes a series of interbedded marine limestone, shale, claystone, siltstone, sandstone, and chert units. Limestone and shale are the predominant lithologies in the upper approximately 675 ft, while the lower portion contains five distinct sandstone units and more abundant shale, claystone, siltstone, and coal than the upper zone. A cherty sandstone at a depth of 1,130 below ground surface (bgs) was encountered. At a depth of about 1,000 ft to 1,116 ft bgs, a non-marine sandstone unit was encountered. This sandstone is the hydrocarbon bearing layer. Joints and fractures observed in the limestone had dips ranging from 0 to 90 deg. from horizontal with joint and fracture surfaces that ranged from planar to irregular and smooth to rough. Several, near vertical shear planes with slickensides were observed with surfaces that were generally smooth and planar. RQD values for the limestone ranged from 0 to 100 percent but in general were good to excellent."

Jan 1, 2016

By NARAYAN K. BHAGAT, ARVIND K. MISHRA, C. Sawmliana, Rakesh Kumar Singh, Panchanan Hembram

Mining operations in close proximity to dwellings and sensitive structures present challenges in terms of mitigating the undesirable effects of blasting while maintaining productivity and ensuring the safety of surrounding communities. This paper explores the application of advanced blasting techniques, including the use of electronic detonators and the splitting of total explosive charges, to address these challenges. A series of experimental blasts were conducted, comparing blasts conducted with and without splitting of holes, to assess the impact on ground vibrations. The results demonstrated significant reductions in vibration magnitudes when implementing controlled blasting practices with splitting techniques. The findings highlight the importance of total explosive charge in determining ground vibration magnitudes within the danger zone of mine workings. The use of electronic detonators provided precise control over blast sequencing, contributing to safer and more efficient mining practices. These advanced blasting methods offer a practical and innovative solution for conducting safe mining operations near dwellings and sensitive structures, ensuring compliance with safety regulations while sustaining productivity.

Jan 23, 2024

By B. Govindarajan, L. S. Rao, T. C. Rao, B. R. Rao

Laboratory leaching experiments were conducted to extract potassium from glauconitic sandstone, and the effects of important variables were studied. The reduced time plot (RTP) for all of the variables obtained from the experimental data has been quantified by this simple equation: R = 100 (1 - exp (-0.693 *(T/T50)0.605) The time required for 50% extraction (T50) has been correlated by a regression equation to variables such as acid strength, temperature, fluorite: glauconite ratio and % solids. Both of these equations were used to predict the extraction percentage at different process-variable levels. In addition, several other experiments were conducted at arbitrary levels of the variables to verify the equations developed.

Jan 1, 1994

By K. D. Luxbacher, E. C. Jong

Perfluoromethylcyclohexane (PMCH), a member of the perfluorocarbon tracer group of compounds, has been shown to be a viable supplement to the widely used tracer gas sulfur hexafluoride (SF6). This viability stems from the fact that PMCH can be used concurrently with SF6 while maintaining adequate chromatographic separation and comparable sensitivity during analysis. However, the release of PMCH in an underground mine ventilation system is challenging due to its physical characteristics. While SF6 exists as a gas at room temperature and pressure and can be accurately released by a variety of means, PMCH exists as a volatile liquid at room temperature and pressure, preventing it from being deployed in a similar manner. One method to release PMCH is to use a permeation plug passive release vessel (PPRV), which allows for the controlled release of the gas. This paper presents the results of a study evaluating various preparation techniques, plug thicknesses and plug materials of an aluminumvessel PMCH release source, so that a source appropriate for the mine scale may be developed.

Jan 1, 2015

By James J. Fallon

The industrial minerals industry is defined loosely and a specific list is presented. Criteria by which to judge prospects and examples are provided. General trends of the industry are observed.

Jan 1, 1984

By Gino Vogt

In mechanized tunnelling operations performance, consumption and safety are main factors for jobsites. One of the most important components effecting these factors, especially in slurry TBM operations, are Slurry Treatment Plants (STPs). Inadequate/ suboptimally dimensioned and designed STPs create bottlenecks for tunnelling operation and jeopardize time schedules and performance. Inefficiently planned STPs could drastically increase consumption figures such as electrical power, bentonite, water and polymers, etc. Inaccurately selected and treated suspension properties can cause a high-risk potential for the whole job. This paper debates the relevant key parameters for STPs from start to finish of a project and its results in influencing factors from the manufacturer´s point of view.

Jun 13, 2021

"A carefully planned laboratory test program is the foundation for the successful development of a sulfide flotation process. In this paper, the development of a copper-molybdenum flotation process is described. However, the concepts discussed can be applied to most sulfide flotation systems and to many industrial minerals projects as well. Each step is examined, beginning with sample procurement and covering sample preparation, flotation test preparation grinding, scoping flotation tests for reagent scheme selection, rougher flotation parameter evaluation and cleaner circuit evaluation, through to locked-cycle testing and pilot plant design and operation. Ore variability and modeling to determine the response of various ore types to the optimum conditions established is also examined.IntroductionA carefully planned laboratory test program is essential for the successful development of any sulfide flotation process. These programs usually begin with a series of batch tests on several ore type composites to evaluate appropriate reagent schemes and delineate optimum rougher flotation conditions, such as primary grind size, flotation pulp density, flotation pulp pH and retention time. Cleaner parameters such as regrind size requirements, cleaner pH, pulp density and number of stages are then defined. Semicontinuous locked-cycle tests are performed using the parameters established in the batch tests to determine the effect of middling streams recirculation on flotation performance. The data generated and the experience gained in the locked-cycle tests may be used to design and operate a continuous pilot plant if relatively large amounts of concentrate are required for further process development, such as optimization of byproduct molybdenum production from bulk copper-molybdenum concentrate.A comprehensive ore variability program is undertaken to determine the response of various ore types to the optimum conditions established. These ore variability programs often test hundreds of samples in standardized batch rougher and cleaner tests to ensure that the orebody is well understood.This article describes the development of a copper-molybdenum flotation process, but the concepts discussed can be applied to most sulfide flotation systems and many industrial minerals projects. The block flow diagram in Fig. 1 provides an overview of the development process."

Jan 1, 2016

By Ma Lianren, Wang Duolun, Chenzhe Li, Hongyan Xie, Fenglan Luo, Huixin Jin

In this study, the oxidation of low-grade pyrolusite to potassium manganate in alkaline solutions under O2 pressure has been investigated. The effects of different conditions on the high-grade and low-grade pyrolusite leaching process were investigated based on thermodynamic calculation, as well as the reaction mechanisms and kinetics of the low-grade pyrolusite during the leaching process. The results showed that the manganese conversion rates of the two types of pyrolusite were almost the same, and reaching 99% for high-grade pyrolusite and 96% for low-grade pyrolusite under optimal conditions. The optimum condition for low-grade pyrolusite sample JM-2 was achieved as 0.5 MPa of the oxygen partial pressure, 55% of KOH, 14 of the initial alkali-manganese ratio, and ≤ 48 μm of the mineral granularity at 260 °C within 150 min of leaching time and 500 rpm. In alkaline leaching of low-grade pyrolusite, Mn(IV) was oxidized into Mn(VI). The particles changed from large particles to flakes and finally formed crystals. Finally, the shrinking core model was used to fully describe the leaching kinetics of the manganese. It was demonstrated that the leaching of manganese was controlled by the chemical surface reactions and the activation energy which equals 115.9121 kJ/mol.

Dec 3, 2022

By Kasimcan Koruk, Julian M. Ortiz

Building a geological model is important in resource estimation, as it defines the extent of domains for estimation. Geological models are built by assigning a domain to the samples, based on logging of different features related to lithology, alteration, and mineralization. Then, the extent of these domains is determined using geometric or geostatistical tools. However, these models should account for uncertainty, since the actual extent of these domains is not known and must be extrapolated from the labelled samples. With the availability of geochemical datasets and machine learning techniques, employing multiple variables to build resource models should be considered. This article proposes a two-step machine learning approach with an ensemble implementation to define geological domains and their uncertainties. First, an unsupervised binary clustering method labels the geochemical samples into two domains. These labelled samples are used to inform a geological domain model built by support vector classification. This application is repeated with subsets of variables and subsets of samples, leading to an ensemble learning method. Weak models are produced with each subset of samples and variables, and combined to devise a stronger learner. The final model accounts for uncertainties thanks to the ensemble implementation. The proposed workflow is demonstrated on a dataset from a porphyry copper deposit, applied hierarchically to define four domains. Performance is comparable with traditional methods, but provides the advantage of allowing domain knowledge in the selection of the variables, and generates domain boundaries that can be controlled in terms of their continuity and smoothness.

Oct 11, 2023

By Vincent T. Ricca

Acid mine drainage is a serious water pollution problem, for its contaminants will eventually effect the quality of the receiving streams. According to the Appalachian Regional Commission (1969)1, 10, 500 miles of streams have been polluted by mine drainage, and 70 percent of this acid pollution is accounted for by underground mines. Due to the severe damage to aquatic life, to recreational and industrial use, and to domestic water supply, more stringent mining and anti-pollution laws have been legislated and coal mine operators are required to treat the mine water discharges to meet the minimum standards. For years now, abatement and treatment methods have been extensively studied. Progress reports presented in the Fourth Symposium on Coal Mine Drainage Research, 1972 1 suggest that a thorough investigation and understanding of the basin discharge is necessary in order to cope with the mine drainage problem. The extent of mine water discharge contamination can be considered as a function of the basin streamflow and acid generation load.' A conservative treatment cost estimation these days is $0.40 per 1, 000 gallons for water with 100 ppm iron, 500 ppm acidity. These figures need not include collection and pumping costs nor the cost of dispersing of chemical waste by-products. To achieve optimal abatement and treatment of mine drainage, predictions of the quantity and quality of mine water discharges are needed. Basin discharge is a continuous process and it can be considered as a. macro-system. This system can be subdivided into micro-systems to describe the various mine discharge .types in the basin. The mining activities could produce acid water discharges from deep mines, stripmines, or associated gob piles. A total study entitled ?Resource Allocation to Optimize Mining Pollution Abatement Programs?* will consider all of these sources. However, this paper will discuss only one micro-system, the drift (deep) mine type. We will look at a single mine and its watershed. The total research project considers a multiple mining complex in an extensive stream basin.

Jan 1, 1973

By A. D. S. Gillies

Loss of visibility due to the occurrence of atmospheric fogging in underground mine airways can lead to a reduction in travel times and loss of production efficiency, an increase in the frequency of vehicular and foot traffic accidents and difficulty in checking rock surfaces for instability and loose material. Where hot and humid surface air meets colder underground air, conditions for fog formation nay be present. Further, suspended particulate matter from diesel exhausts or stoping operations together with slow movement of air along passageways nay contribute to formation. The study describes an investigation being undertaken with the cooperation of Kennecott's Ozark Lead Company to identify causes of the problem.

Jan 1, 1982

By EREN KOMURLUR, ATILA GURHAN CELIK, IBRAHIM GUNES

In this study, laboratory and site studies were performed to investigate the usability of a new insertion apparatus designed for the split-set type of friction bolts. The new apparatus decreases the friction during the bolt insertion by a temporary diametric compression of the split tubes. According to the results, the new precompression apparatus was found to be advantageous in terms of the insertion practicality and prevention of the buckling problem. By allowing increases in the ratio of bolt diameter to drill-hole diameter, the new apparatus was found to supply relatively high normal stresses and friction capacity in drill holes after opening its clamping mechanism.

By Jeremy Maurer, Duah Philip, Awuah-Offei Kwame, Donya Otarod

Land use impact assessment for mining is time- consuming and expensive. Because of mining’s impact on biodiversity, land use assessment methods that evaluate biodiversity are important for mining land use impact assessments. Remote sensing, in particular satellite multispectral sensing platforms such as Sentinel‑2 and the Landsat mission series, have been used to assess and quantify biodiversity through proxy variables such as NDVI (Peña-Lara et al., 2022). The objective of this paper is to present results of a comparative study of land use and biodiversity based on multispectral satellite observations and production data from copper and cobalt mining in the Democratic Republic of Congo. We quantify the relationship between different spectral bands and vegetative indices and the production data provided by the mining companies and measure correlations. The results suggest that remote sensing could be a cost- effective means of assessing biodiversity impacts of mining.

Feb 1, 2025

By Irene Bendanillo, Canon Cheung, Justin Lianides, Derek Penrice

The SLAC National Accelerator Laboratory’s two-mile-long particle accelerator generates the world’s brightest X-rays from its Linac Coherent Light Source (LCLS) freeelectron laser. This facility has driven groundbreaking discoveries in medicine and industry. The LCLS-II-HE project will provide a significant increase in laser energy, allowing cutting-edge research in fields including biology and environmental science. A key project component is the Low Emittance Injector Tunnel (LEIT), a 240-foot-long tunnel to be built alongside the existing accelerator and connected to it via a 30-footlong Transfer Tunnel. This paper discusses site and scientific constraints that led to the selection of the LEIT configuration: tunnels to be constructed using the sequential excavation method in mixed-face conditions comprising native rock and placed backfill, and critical design considerations including protection of overlying and adjacent historic structures and structural accommodation of near-fault seismic loading.

Jun 13, 2023

By V. Claremboux

The transformation of raw iron ore into high quality steel can take place via several processes. A general consistent theme involves the upgrading of the iron ores via methods such as flotation and magnetic separation, the preparation of an agglomerate such as via pelletization or sintering, the smelting of the agglomerate into a high grade iron product, and the further refining of iron into specific steel alloys. Each of these steps admit potential for optimizations and alternatives, and the process overall is critical to meeting the world’s continuing iron demands.

Feb 1, 2025

By James C. Franklin

Companies are constantly searching for more effective methods of controlling and reducing costs. In recent years increased emphasis has been placed on cost reporting to the middle manager and down to the first-line foreman because this is the place where the money is really spent. Traditionally, operations management has been relegated to using cost systems designed by financial management for the use of financial management. They reflect the machinery necessary to produce profit and loss statements, and so-called cost reports emanating from these systems frequently have a heavy orientation toward product costing rather than the cost that an individual manager or foreman actually controls. In addition to direct operating costs by function or product type, they often include overhead allocations from local operations as well as from the home office. This type of full-absorption costing has many worthwhile uses but is of little or no use to operations management for cost control purposes. It is particularly discouraging to many supervisors because it includes so many categories of cost over which they have little or no control. It is for this reason that modern, aggressively managed companies are increasingly moving in the direction of responsibility cost reporting. It is the objective of responsibility cost reporting to report only direct operating costs over which the individual manager or foreman has complete control, thus facilitating cost control by fixing responsibility for cost.

Jan 1, 1979

By C. H. Grant

On the Mesabi Range, Ammonium Nitrate is used for blasting a variety of materials having widely varying blasting characteristics. The materials vary from hard, dense, magnetic taconite, which requires heavy blasting, through relatively soft, earthy, direct shipping ores, which require only light blasting to facilitate shovel operation. In view of the fact that materials gradational between these two end members are encountered in large tonnages, it is evident that a wide range of blasting situations face the mine operators on the Mesabi Range. In April of 1956, at Cleveland-Cliff s Hawkins Mine near Nashwauk, Minnesota, a fertilizer grade of Ammonium Nitrate prills was first used as a blasting agent. This first attempt was made without the addition of any carbonaceous material and even though it did go off, the force was not sufficient to produce the required results. Fuel oil was then added In the amount of one gallon for each 80 pounds of Ammonium Nitrate, with the oil and Ammonium Nitrate being added to the hole simultaneously. This blast was successful. Since then most of the mining companies have used Ammonium Nitrate, experimenting with various ratios of oil and fertilizer, mixing these ingredients either before or during loading of the holes. Since the additional of fuel oil to the Ammonium Bitrate before loading produces a more uniform saturation, most companies have adopted the method of pouring the fuel oil directly into the Ammonium Nitrate bags and then pouring the mixture into each hole. The ratio of 3- ½ quarts of fuel oil to each 80 pound bag of Ammonium Nitpate prills is now being used.

Jan 1, 1958

By A. T. Yu

A recent analysis completed by the United States Department of Commerce predicts that the 1968 Gross National Product will reach a record high of 864 billion dollars. As our nation annually increases its total output of goods and services, as has been the trend, the consumption of steel and its most basic raw material - iron ore - also must increase, To deliver the most economical unit of iron ore to the blast furnace, each segment of the transportation system must be co-ordinated and utilized to its highest degree of efficiency. In some cases, such as with the water segment of the system, a new investment in capacity will be required.

Jan 1, 1968

By P. S. Sundar

A laboratory method for the simulation of in-situ leaching of uranium was developed under contract to the Interior Department's Bureau of Mines. Simulation tests using sulfuric acid, ammonium bicarbonate and sodium carbonate as reagents and hydrogen peroxide as oxidant were carried out with representative ores from Texas and Wyoming. The tests not only yielded recovery rates of uranium and permeability changes, but also qualitative inferences on the chemical and physical phenomena which occur underground. Leaching with basic solutions was found to be kinetic constrained and with acid solutions, equilibrium constrained. The rapid permeability changes observed when leach solutions were introduced, were probably caused by gas blockages in the packing. Precipitation of calcite or gypsum and the reaction of clay to leach solutions had slow and gradual effect on the packing permeabilities.

Jan 1, 1978

By R. Schlüter

"The “Biohydrometallurgical Center for Strategic Elements (BHMZ)” is a cooperation of 13 departments of the Technical University Bergakademie Freiberg fostering interdisciplinary research along the whole (bio-) hydrometallurgical process chain to extract indium and germanium from sulphide ores. Research comprises methods to (i) bring the respective metal from the source material into aqueous solution and (ii) different approaches to extract pure metal or metal-containing materials from the solution. Within the BHMZ the Department of Underground Mining Methods deals with the design and implementation of an underground testing facility for bacterial in-situ stope leaching in its own “Research and Educational Mine”. The intention is to investigate innovative approaches for leaching technologies by crack initiation due to hydraulic fracturing or water pressure blasting under consideration of leaching kinetics and underground conditions. It is planned to set up two testing units comparing energy input and the metal output of conventional (blasting) as well as one of the innovative technologies. Aim of subproject is to establish an innovative and sustainable method ready for up-scaling. BACKGROUND Metals like copper and zinc mainly occur as sulphide ores in nature. Due to the insolubility of these sulphide minerals the respective metal is commonly extracted by pyrometallurgical processing methods. These methods require several steps of enrichment of concentrates such as flotation and roasting (Figure 1) under extensive energy utilization. Additionally, this arouses the emission of sulphur dioxide gas which can have a negative impact on the environment in form of acid rain, as long it is not caught by sulphuric acid facilities (Schippers et al. 2011). However, to treat the ore on the surface either open pit or underground mining operations are necessary. This implies operation steps from excavating, loading, and conveying/hauling, to dumping with the sub-processes crushing and stashing. Due to the tendency of increasing depth, more complex ores and decreasing ore grades of the mineable deposits as well as increasing energy and environmental costs these conventional mining and processing methods become in general more costly and difficult to apply. Hence, hydrometallurgical processes and especially the suitability of bioleaching as an alternative in-situ method for future mining projects should be examined. Leaching by means of microorganisms is a combination of mining and processing by converting the insoluble metal into an aqueous form. This technology is an economically beneficial and environmentally friendly alternative to pyrometallurgical processing methods especially for primary and secondary low grade ores. Mainly the extraction of copper but also of zinc and lead from sulphide ores is state-of-the-art in surface leaching operations like heap and dump leaching (Figure 1)."

Jan 1, 2015