Search Documents

By Robert W. Elayer

For the design of a coal mine and process plant, a comprehensive foundation of geologic information is essential. Historically, the development, collation, and use of this information for design have been costly and time consuming. With the application of a digital computer, however, the effort expended can be reduced and maximum effective use of the geologic information realized. The purpose of this paper is to demonstrate the feasibility and convenience of using a computer to Store and manipulate geologic data for use in mine and process plant design.

Jan 1, 1975

By Ray Nivens, Umit Turunc, Caroline Sui, Nick Morrison, Douglas Steiner

"In most copper mines and concentrators, mill water is continuously recovered and reused, with fresh water added to make up for losses. When mixed, these water chemistries can lead to severe scaling, especially in pipes, tanks and pumps on the mill water supply side, reducing flows and causing significant production losses.At KGHM Robinson Nevada Mining Company, increases in the fresh water addition ratios resulted in severe scaling problems and premature pump failures thereby jeopardizing plant production. What initially appeared to be a few isolated scaling events eventually unfolded into a recurring pattern of water supply-related production losses with increasing severity. Through completion of detailed root cause analysis, chemistry modeling, laboratory work, in-plant testing and system engineering, the mechanisms of scaling were identified and addressed.Advancements in fresh water addition practices and antiscalant application methods resulted in a stepwise reduction of the mill water scaling. Cost savings and production benefits were significant to the plant’s financial metrics.IntroductionThe production of mineral and metal concentrates using the flotation process requires large quantities of water. Flotation is utilized as the primary means for beneficiation with sulfide ores. Mined ores are crushed and ground into a slurry of 20-55% solids. For each ton of ore, 400-900 gallons of water1 are needed to supply the grinding mill. Additional water is needed in the flotation circuit as well. With many modern mills operating at2 11,000-165,000 tons/day, water supply volumes can be upwards of 3,000 gpm to 100,000 gpm of flow.For plants operating at or above capacity, disruptions and restrictions in water supply flow can have a direct impact on the production and recovery of the metal. Water supply flow can be limited for a wide variety of reasons but of interest are those limitations that are due to mineral scaling. Mineral scaling is the selective point precipitation of inorganic species above saturation concentrations. Precipitated species form flow-restricting deposits in the mill water system (tanks, pumps, pipe and valves), that will eventually impact water supply to the concentrator."

Jan 1, 2017

By Jieliang Wang, Shiwen Yi, Zhao Cao, Peng Zu

Bayan Obo ore contains mainly bastnaesite, monazite and associated iron, fluorite, calcite, dolomite, barite, and trace amount of columbite. Due to its complex mineral compositions and similar mineral properties, it is difficult to separate and obtain rare earth and fluorite concentrates with high purity by conventional magnetic separation and flotation. In this paper, a stepwise magnetic separation process comprised of wet permanent magnetic separation (PMS), wet electromagnetic separation (EMS), and superconducting magnetic separation (SCMS) was proposed to pre-concentrate iron, rare earth, and fluorite minerals from Bayan Obo ore. The results showed that iron, rare earth, and fluorite preconcentrates with high purity and low impurity content could be achieved, which might be helpful to shorten the technological process and improve the separation efficiency for the subsequent flotation of iron, rare earth, and fluorite minerals.

Sep 15, 2020

By T. A. de Almeida, M. de Paiva Bueno, M. Powell

The mining industry is one of the foundations of modern society, providing not only the raw materials needed to maintain a contemporary lifestyle, but also serving as a basis for the development of future technologies. From the most basic components of an appliance to the materials needed to design an electric car or a space rocket, each raw material has gone through a painstaking procedure of extraction and processing, and ways to make this process more efficient will be of great help to meet an ever-increasing demand for minerals. One of the biggest challenges when extracting mineral resources is to measure the variability of the mineral body prior to processing. Comminution is the most power-demanding stage, and the lack of geometallurgical testing, often for financial reasons, may result in an inefficient operation. The Geopyörä Rock Breakage test was developed with the objective of making mineral variability data more accessible by providing both standard comminution parameters and rock mechanical properties at low cost, and with a modest sample size, allowing a larger number of samples to be tested to reduce uncertainties and assure productivity. The objective of this paper is to present the results of an extensive validation of this new rock breakage method against two of the main tests currently in use, namely the SMC® and Bond ball mill work index tests. More than 100 samples have been tested and the results compared, showing that the new method can accurately estimate the parameters of the traditional tests. This confirms that the new test is a reliable tool for comminution and geometallurgical tests.

Feb 1, 2023

By G. Guzman, L. Sevilla, M. Botz

"Newmont Mining Corporation operates the Yanacocha mine in Perú and the gold milling section of the property includes a Sulfidization-Acidification-Recycle-Thickening (SART) plant to remove copper from pregnant leach solution. Since its commissioning in 2008, the plant has been intermittently operated as needed to remove copper upstream of a carbon adsorption circuit. However, starting in 2015 Newmont expects the plant to operate on a more continuous basis in response to higher copper ores that will be processed in the gold mill. In anticipation of this, Newmont conducted a campaign in May 2014 with stockpiled high-copper ore to evaluate performance of the SART plant with elevated levels of copper in feed solution. Results from the campaign demonstrated the SART plant is capable of efficiently treating high-copper leach solution. During the campaign, leach solution copper levels ranged from about 100 to 700 mg/L, and copper removals ranging from about 56% to +99% were achieved. The median copper removal efficiency observed during the campaign was about 94%. The primary plant modification determined necessary following the campaign was the need to improve consistency with sulfide dosing. INTRODUCTION Copper removal from cyanide leach solution can be affected through the addition of sulfide at acidic pH to precipitate copper sulfide as a solid. There has been renewed interest in the process in the past several years due to the increasingly common issue of high copper levels in cyanide leach solutions. The term Sulfidization- Acidification-Recycle-Thickening (SART) is used as an acronym for the process according to the primary unit operations utilized. At a pH of approximately 4.0 to 5.0, the addition of soluble sulfide to a copper-bearing leach solution will result in the precipitation of copper sulfide (Cu2S) solid. The overall acidification and sulfidization reaction is (assuming the use of sulfuric acid for pH adjustment): 2Cu(CN)3-2 + 3H2SO4 + S-2 ? Cu2S(s) + 6HCN(aq) + 3SO4-2 The above reaction is written relative to the copper-cyanide complex 2Cu(CN)3-2, though analogous reactions also take place with the other common copper-cyanide complexes Cu(CN)2- and Cu(CN)4-3. Sulfide in the above reaction (S-2) is normally supplied as sodium hydrosulfide (NaHS) purchased in solid or concentrated liquid form. Two characteristics of this reaction that are beneficial to a leaching operation are: 1. Copper is removed from solution as Cu2S (synthetic chalcocite) solid, which can then be sold to a smelter for its copper value. 2. Cyanide that is complexed with copper in the leach solution is released as free cyanide, thereby regenerating cyanide that can be recycled to the leaching operation for continued use."

Jan 1, 2015

By Ryan Marsters, Adam Pring

The Rawah Ditch is a mountainous water supply diversion which supplies Larimer County, Colorado with water since 1903. The ditch includes two historic tunnels excavated by drill and blast through a gneissic rock buttress. Both rock tunnels were failing with annual convergence. After a snowshoe-accessed eld investigation, nite element modeling, and an alternatives analysis, a diameter DE pipe was inserted within each tunnel and the annulus lled. The proect was implemented in an Alternative Delivery contract lasting ve months from eld investigation through procurement and construction.

Jun 23, 2024

By Dr. Jack M. Gillette

A system of models which simulate surface coal mining operations has been developed for use in mine planning and economic evaluations. Micromodels simulate individual mine operations for equipment selection and mine planning. Macromodels simulate all operations in the complete mine for economic evaluation of reserves. A cash flow analysis model makes a complete discounted cash flow analysis to deter-mine a required coal sales price or return on investment for evaluation of any mining project.

Jan 1, 1978

In 1981, North American Degerstrom Contracting began gold mining on the Little Rocky Mountain Range, near Zortman, MT. In the past four years, the price of gold has fluctuated from a high of $16/g ($500 per oz) to a low of $9.60/g ($300 per oz). With that kind of a moving target, profitability presents a management challenge. Based in Spokane, WA, Degerstrom employs 85 people at the mine. It is one of the largest heap leach operations in the nation. Last year, 8 Mt (9 million st) of low-grade ore was moved to the leach pads in a two-shift, five-day operation. The current pit being worked produces 218 kt/m (240,000 stpm) of leaching ore. Ore fragmentation critical The gold bearing ore has no defined patterns or seams. It is an igneous intrusion resulting from volcanic activity. It occurs spontaneously throughout the range. To recover the gold, areas are staked out and core samples are taken and analyzed. These data determine if the ore is rich enough to mine. Once mining begins, an average of 150 holes are drilled and blasted on a two-day rotation. Five Ingersoll-Rand T4s drill on a 4- x 4.5-m (14- x 15-ft) spacing to a 7.6-m (25-ft) depth. "When we first came to this site, we drilled on a 3.6- x 3.6-m (12- x 12-ft) pattern," said Paul Baker, superintendent for N.A. Degerstrom Contracting. "We did some experimenting using a high density emulsion in the bottom of the hole and filling the rest with regular Anfo." The high density emulsion saved the company on overall drilling and blasting costs since the holes could be spaced on a wider pattern and still achieve the high degree of fragmentation needed for leaching. Blasting is important because the gold lays in the natural strata of the rock. Also, the ore is not crushed before it goes to the leach pads. So complete fragmentation is critical. Terrain dictates loading/hauling system The shot ore is worked in 6 m (20 ft) benches by two Caterpillar 245 front shovels equipped with 3 m3 (4 cu yd) buckets, a 992C wheel loader with a 12.6-m3 (16.5-cu yd) bucket, and a 988E high lift fed by a D9H. A Caterpillar D10 tractor trap dozes to the loader. According to Baker, the 6 m (20 ft) bench is an efficient lift for the front shovel and the wheel loader. In tight quarters or in a pocket of ore, Degerstrom uses the 245s. For high production areas, the wheel loader is used. The hauling fleet includes 28 Cat 773 off highway trucks. The 45 t (50 st) trucks are seven pass loaded by the 245s with a 25-second cycle time per bucket load. The 992C loads the trucks in two passes in less than 30 seconds. The cycle time is four to five minutes for a 1.2-km (4000-ft) haul on grades that average 10%. Grades, in some places, exceed 16%. "We use the 773s because they have a low weight-to-horsepower ratio - that's what you need in steep country," Baker said. The trucks haul the shot ore to the leach pad. Currently, Degerstrom is working a pad that has a capacity for 5 Mt (5.5 million st) of ore. Building the leach pads The base of the pads resemble a large drainage basin. They take about one month to construct. A 0.3-m (1-ft) layer of impervious bentonite clay is hauled in and leveled by a Cat D9H tractor. A 30-mm (1.2-in.) PVC liner is then laid in place on top of the clay base. It, in turn, is covered with tailings from an old on-site mill. Degerstrom uses the tailings to protect the liner from tears when the ore is dumped. The ore is leveled and built up in 9 m (30 ft) lifts by the D9H. The tractor rips the top layer. Then, a network of plastic irrigation pipe is put in place to distribute a cyanide solution over the surface. The leaching solution percolates through the ore and dissolves the gold. The solution drains from the pads and is pumped to a 22.7-ML (6-million gal) pregnant solution holding pond. The liquid then goes through two separate filtration units. One unit removes entrained solids and the other side adds a zinc dust to precipitate the gold. This is collected on filters. The affluent then returns to a solution holding pond for redistribution through the pipeline network. Typically, 80% of the pad's potential recovery takes place in the first 30 days of leaching. The process stops when the ambient temperature falls below the cyanide's freezing level. And each pad has a leach cycle of four to five years before recovery values decline to a point where further leaching becomes uneconomical. At Zortman, it takes 9 t (10 st) of ore to produce 31 g (1 oz) of gold. It is therefore critical to keep total production costs down and efficiency high.

Jan 1, 1986

By William Gleason

"There are signs that the commodity downturn that has battered the mining industry for the past five years is beginning to ease up. As the dust begins to settle and mining companies begin to take stock of the battle, Newmont Mining Corp. will be one that is standing strong with just a few scrapes and bruises thanks in large part to the leadership of president and chief executive officer Gary Goldberg and his right hand man and chief operating officer, Chris Robison.As he closes in on retirement (for a second time) Robison, a third-generation miner from Nevada, took time to speak with Mining Engineering about a 33-year career in which, among other things, he is credited with not just helping Newmont survive the turbulent times but with steering the company to a safer, more productive and more profitable heading.“I think we did it better than anyone else,” Robison said when asked how the company fared during the past five years. “We didn’t talk about it a lot, we just put together a strategy and we delivered.”What Newmont, the world’s second-largest gold mining company by production, delivered since Robison took the position of chief operating officer in 2013 are improvements in costs, porduction, projects and safety.Operating under the mantra of “live within your means,” Robison was pulled out of retirement from Rio Tinto and into a challenging situation at Newmont. The price of gold was in a nose dive from a high of nearly $58/g ($1,800/oz) and heading to levels closer to $38.60/g ($1,200 oz).“Newmont is a big ship that can’t be turned, but has to be steered,” said Robison. “We recognized that we had to set a new course. The direction the ship was going was great for $1,600 to $1,800/oz gold but we were chasing ounces.”Like the rest of the gold mining sector before the falling gold prices, Newmont was focused on volume and was looking for gold wherever it could be found. The slogan at Newmont in 2011 was “7 million ounces a year by 2017.”When Robison came on board it was a different reality.“We had to begin focusing on value over volume as the cornerstone of Newmont going forward,” he said."

Aug 1, 2016

By C. J. Bise, P. Bucks

Central Appalachian coal reserves are a valuable natural resource in high demand, both domestically and internationally, justifying efforts to increase percentage recovery through pillaring. Unfortunately, the challenge associated with pillar extraction introduces additional safety risks during the activity. Although pillaring developed prior to mechanized mining, current technology and mining practices have made this form of mining highly modernized. However, current fatality trends suggest that work still needs to be done to control the residual risk that is not controlled by modern practices, such as those having a personnel-performance-based component. This paper investigates the application of modern coal pillaring techniques and will present a risk-management-based strategy that targets personnel-performance-based risk, in order to improve the ability of safety engineers, managers and trainers to provide training programs addressing the needs of pillaring sections.

Jan 1, 2012

By Christopher E. Dianora, Matthew Sorrell, Eileen Test

"Constructed between 1939 and 1945, the Rondout-West Branch Tunnel (RWBT) portion of the Delaware Aqueduct is 45 miles (72 km) long. The New York City Department of Environmental Protection (NYCDEP) first identified suspected areas of leakage from the RWBT in the 1990s. A $1 billion project is underway to mitigate the leakage through the construction of a bypass tunnel around the area of most severe deterioration, a 2.5-mile (4 km) section located beneath the Hudson River. Two shafts, 800 and 900 feet (244 and 274 m) below the ground surface, are being sunk to support the tunnel construction. The deep shafts will be subjected to high groundwater pressures and have been designed to accommodate multiple tunnel portals. This paper discusses the engineering decisions and analyses leading up to the final design. INTRODUCTION Project Background The New York City Department of Environmental Protection (NYCDEP) provides over 1 billion gallons (3.7 billion liters) of water to over 9 million residents of the City of New York and surrounding communities each day. This water is stored in upstate reservoirs and conveyed to the City via a system of aqueducts and tunnels. Water is delivered to the City almost completely by gravity and consists of three systems: the Croton, the Catskill, and the Delaware. The Delaware System is the largest of the three and supplies between 50% and 70% of the City’s daily water supply. In the 1990s, the NYCDEP discovered leaks in the central 45-mile-long (72 km) portion of the Delaware Aqueduct known as the Rondout-West Branch Tunnel (RWBT). The leaks release between 15 and 35 million gallons per day (MGD) (132.5 million liters per day) and are concentrated in two areas near Wawarsing and Roseton, New York. As part of the Rondout-West Branch Bypass Tunnel and Wawarsing Repairs Project (Bypass Tunnel Project), the leaks in the Wawarsing area will be repaired by grouting from inside the existing RWBT, and the leaks in the Roseton area will be mitigated by constructing a bypass tunnel parallel to and 1,750 feet (533 m) north of the leaking portion of the existing RWBT. Two deep shafts will be excavated on either side of the Hudson River: Shaft 5B in Newburgh and Shaft 6B in the Town of Wappinger."

Jan 1, 2016

By Alessandro Boscaro, Daniele Martinelli, Cristina Gabriela Oñate Salazar, Daniele Peila, Carmine Todaro

"The wear phenomenon in TBM machines is not a simple issue, as many parameters are playing an important role on the consumption of the tools during a tunnel excavation. The action of the wear due to the contact with the soil can occur on the excavation tools, on the cutterhead, in the excavating chamber and on the screw conveyor. The test developed at the Laboratory “Tunnelling and Underground Space Center” of the Politecnico di Torino is aimed to reproduce the interaction between the tools and the excavated material, simulating the excavation conditions in terms of soil conditioning and water content. The test, which is not standardized, is studied to evaluate the wear in a global point of view. The present work starts by testing the influence of the use of chemical agents during the conditioning phase on the drop of the wear phenomenon, in terms of metal weight loss. 1. INTRODUCTION The wear phenomenon of the excavation tools used in TBM tunneling machines is playing recently a major role in the design stage of full-section tunnels in both soils and rocks. Concerning EPB excavation technology, the main issue regarding productivity is the wear of its components (Peila et al.,2012), which increases the so called dead time in the whole process. The friction generated between the components and the ground causes the consumption of the tools and other metallic components in contact with the ground, described as primary and secondary wear by Nielsen et al. (2006a). This leads to downtime, with risky and complicated maintenance operations (Peila and Schulkins, 2009), as occurred in recent tunneling works in Liguria (Italy). The study of this argument in granular soils is very delicate, as it encloses not only the properties of the excavation tools, but also the characteristics of the ground to be excavated (hardness, mineralogy composition, shape and dimension of the particles and moisture content). The penetration mechanism is based on the scraping of the ground, by mean of cutting tools, with its consequent consumption. Concerning the rocks, the excavation principle is characterized by crushing the rock mass matrix by applying high compressive stresses through cutting disks. In such a way, to avoid frequent downtimes and their consequent economic losses, it is very important to study this subject and therefore understand and forecast the durability of the components, in order to try to maximize the productivity of the machine by reducing the frequency of maintenance stoppings."

Jan 1, 2016

By Erik Sundström, Magnus Nygren

Having seen significant improvements to accident rates in the last 40 years, companies in the Swedish mining industry now show a greater focus on the development of safety cultures throughout their organisations and workplaces. However, there is a lack of research examining the different safety initiatives and strategies practiced in the industry today. This study explores the potential influence and consequences such initiatives may have on the development of safety cultures in the Swedish mining industry. Twelve interviews with experts on safety initiatives from four different Swedish mining organisations were conducted and analysed in a process based on qualitative thematic analysis to identify notable connections to safety culture development. The results of these interviews highlight proclivities in the implementation and use of safety initiatives such as subjects of focus, methods and desired effects. This enables the interpretation of the conceptualisation and methods for the development of safety culture in these organisations based on their approaches to safety development. We believe the results of this study can serve as support for discussions on safety culture development in the Swedish mining industry, and be of interest for international mining industries, in addition to approaches to research in this field. However, we also believe it is important to emphasise the opportunities to approach safety culture in mining from different perspectives than those common today.

Jul 19, 2023

By David G. Chedgy

It is probably safe to assume that most operating personnel working in coal preparation plants are exposed to noise levels in excess of the MESA Noise Regulations unless they are wearing ear protection. The excessive in-plant noise levels have received little attention until recently. Noise control has not been an important design consideration in existing coal preparation plants. This situation is rapidly changing as plant owners and plant operators are requiring that new coal preparation plants be designed to provide a safe noise environment for operating personnel and also meet MESA Noise Regulations. This paper discusses the noise exposure hazards, noise generating mechanisms, and some possible noise control solutions for typical coal preparation plants.

Jan 1, 1975

By William Gleason

For the first time in many years, the Liebherr Group chose to host its annual conference for the international construction trade press in the United States. The reason for the move is simple ? mining. Like other large corporations, especially those in the construction fields, Liebherr felt the effects of the global economic crisis that began in 2008. The slowdown in the housing market was especially hard on Liebherr?s mobile crane and earth moving divisions. The mining division, however, while affected by crashing commodity prices that led to cancelled orders and the loss of financing for some customers, was not battered as badly as the other divisions. And now, with the price of commodities once again on the rise, it seems that it will be Liebherr?s largest machines that lead the family-owned company to better days. ?We can report that our generally optimistic view during the crisis has proved adequate,? said Joachim Janka, president of Liebherr mining equipment, at the conference in Williamsburg, VA, just down the road from the company?s mining truck division global headquarters in Newport News, VA. ?Since the third quarter of 2009, our mining equipment activities have been recording once more a strong and steady demand. This has already yielded a substantial increase in market shares for our product lines of large mining shovels as well as for mining trucks.?

Jan 1, 2011

By H. N. Dougherty

"The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) ventilation gallery was used to study methane-air flows around a continuous miner mockup with water sprays and a scrubber fan. Methane gas was released from pipes located at the face to simulate face gas emissions. Methane concentrations and air velocities were measured while varying parameters such as airflow quantity, entry width (sump or slab cut), and face ventilation configuration (blowing or exhausting curtain). Test data showed a similar pattern of methane concentrations at both low and high airflow quantities, but a difference in the distribution of methane concentrations between narrow and wide entry widths. Most tests showed that blowing face ventilation was more efficient in diluting methane than exhausting ventilation, similar to observations made in previous empty gallery studies. The patterns of airflow and methane concentrations observed in this testing can further improve the understanding of airflow in and around the CM and face, promoting effective use of face ventilation to improve the health and safety of miners. INTRODUCTION Attaining an accurate understanding of airflow distribution at the continuous miner face is instrumental in maintaining a safe mining environment. US mining regulations require that sufficient airflow must be directed to the deepest penetration of the face and render harmless contaminant gases, as verified by the Mine Safety and Health Administration (MSHA). Currently, continuous miner face air readings can be taken in the last open crosscut and at the inby end of the curtain mouth. By measuring adequate airflow in a pre-determined area it is accepted that a sufficient quantity of that air exists to sweep the face of harmful dust and gasses. Unfortunately, due to the location inaccessibility, precise face velocity readings cannot be measured in situ. Face velocities may be estimated through computer-simulated programs based on laboratory models. Improving upon previous empty gallery testing and to more effectively determine representative face methane readings, a mockup of a continuous miner with water sprays and a scrubber fan was used in the current study to further refine face airflow conditions that would be closer to actual mining conditions."

Jan 1, 2016

By Y. Luo

Although considerable progress has been made in the last decade in predicting surface subsidence over longwall panels, a number of important issues deserve further studies in order to improve the techniques and accuracy of subsidence predictions. Some of the problems are: (1) subsidence over the chain pillars between mined longwall panels; (2) subsidence development process after face stop due to either a vacation or the completion of a longwall panel; and (3) subsidence initiation and development process over the setup entry area in the initial stage of mining a longwall panel. In this paper, the measured data related to the targeted problems are presented, the data analysis techniques are briefly introduced, and some of the prediction methods developed based on the collected data are proposed. The proposed methods can be used as supplemental tools for the existing subsidence prediction models to improve their prediction accuracy.

Jan 1, 1991

By D. W. Cooper

The AMAX of Canada Limited Kitsault mine is located approximately 150 kilometers, by air, north of Prince Rupert, British Columbia at the head end of A1 ice Arm, just east of the southern tip of the Alaskan Panhandle. It is presently only accessible by sea or air, although a road is being constructed by the company which will provide access to Terrace, a commercial centre with a population of about 15,000. The topography is typically coastal mountainous with peaks rising to 2,100 meters around the head end of the inlet. The concentrator is at an elevation of 515 meters with the mine at 630 meters. This open pit molybdenum mine was previously operated between 1968 and 1972 by British Columbia Molybdenum Limited, a subsidiary of Kennecott Copper Corporation. AMAX of Canada Limited has spent $194 million to refurbish and expand this operation.

Jan 1, 1982

By J. L. Francke

This paper describes the practices and methods used in a study of Time Domain Reflectometry (TDR) as an inexpensive deformation monitoring tool in underground excavations at the Waste Isolation Pilot Plant (WIPP). The WIPP is being developed near Carlsbad, New Mexico, for the disposal of transuranic nuclear wastes in bedded salt 655 m (2 150 ft) below the surface. Data collected from WIPP geomechanical monitoring are used to characterize conditions, confirm design assumptions, and understand and predict the performance of the deep salt excavation. The geomechanical monitoring program encompasses numerous geomechanical monitoring techniques ranging from inspection of observation boreholes to advanced radar surveys. In 1989 TDR was introduced as a monitoring tool with the installation of 12.7 mm (0.5 in) diameter TDR cables in the underground excavations. In 1993, a new TDR system was installed in a separate location. Based on experience with the previous installation, enhancements were implemented into the new TDR system that: 1.) extended the period of performance by increasing cable diameter to 22.2 mm (0.875 in), 2.) increased accuracy in locating areas of deformation by aligning cables with nearby observation boreholes, and 3.) improved data acquisition and analyses using a standard laptop computer, eliminating the chart recorder previously used. In summary, the results of a correlation between the TDR signatures to nearby observation boreholes and geomechanical instrumentation will be presented.

Jan 1, 1996

By Byron C. Hardinge, Michael Sokaski, Paul F. Sands, W. Loring III Mc Morris, David J. Akers

INTRODUCTION In the early days of coarse-coal cleaning by the dense-medium process in Europe, loess was one of the materials used for medium solids. Newly developed cyclones were used to reclaim and thicken the loess suspension. On occasion, when the cyclone thickener at the Maurits mine in the Netherlands plugged, the overflow was found to be filled with clean coal free of impurity. From this observation stemmed the concept of the cyclone as a cleaning device. Development took place during World War II in the laboratory of the Dutch State Mines under the direction of M. G. Driessen. A 15-tph (13.6 t/h) pilot plant was in operation in the laboratory by 1945, when, in September, Driessen made the first public disclosure of the process in a paper presented to the Institute of Fuel in London.51 In April 1945, operation of this pilot plant was observed by H. F. Yancey, who was so impressed with the potential of the cyclone process that, on his return to the United States, a research program on the cyclone was immediately started by the US Bureau of Mines (USBM). This work led to an AIME paper in 1946 in which the first details of cyclone operation on American coals were made available.52 Commercial adoption of the cyclone proceeded in Europe, initially in the Netherlands, Germany, and France. In the United States, where coal is less costly and most of the coals are easy to clean and respond well to simpler cleaning processes, the first cyclone plant was not built until 1961.53 THEORY Before discussing the theory of a dense-medium cyclone, a brief description may be helpful to some readers who are not familiar with its basic operation. In a typical dense-medium cyclone, illustrated in Fig.7-51 a mixture of medium and raw coal enters tangentially near the top of the cylindrical section, thus forming a strong vortical flow. The refuse moves along the wall of the cyclone and is discharged through the underflow orifice. The washed coal moves toward the longitudinal axis of the cyclone and passes through the overflow orifice, or vortex finder, to the overflow chamber. Washed coal is discharged from this chamber, usually through a tangential outlet.

Jan 1, 1991