Search Documents

By S. S. SHINDE, P. C. JIKAR, N. B. DHOKEY

Mill scale is an oxide waste product of the steel mills, which contains around 70% iron and other allied impurities. In the present context, a dynamic prototype counter current reactor (CCR) has been used for experimentation and simulation of particle bed by using discrete element method (DEM). Mill scale was pulverized to ASTM mesh range 140 (106 μm)/ + 270 (53 μm), and then it was oxidized in CCR to make single oxide Fe2O3 phase by maintaining required thermodynamic conditions such as pure oxygen at 1100 °C. Then this oxidized powder was subjected to reduction reaction in CCR having gas mixture ( H2:N2) ratio of 1:4 at 875 ± 5 °C for filling degree (fd) and reactor revolution (ω) ranging from 5.38 to 16.14% and 2 to 5 rpm, respectively. A creeping fluid flow condition (Re ˂ 1) and natural heat convection (Gr/Re2 ˃˃ 1) has been maintained while undergoing solid–gas reaction. Besides particle bed behavior has been quantified by Froude number (Fr) for the optimum operating window. The simulation was validated by the experimental results of reactor reaction product by X-ray diffraction (XRD) and scanning electron microscope (SEM) images. Prevailing heat transfer mechanism and reduction reaction mechanism has been established for solid–gas counter current conditions.

Nov 22, 2021

By Bryson D. Trexler

Slope stability in open pit mines is governed by rock structure, rock quality, ground water conditions, blasting, pit geometry and excavation method. Of these factors, the control of ground water pressures often represents the primary tool to improve slope stability. Production equipment has recently been used to stabilize two slide areas by dewatering using blasthole drills for vertical holes and secondary drills for horizontal holes. This paper describes both of these dewatering programs and contrasts an earlier slope stabilization program that employed a subcontracted horizontal drill.

Jan 1, 1983

By R. Venugopal, V. K. Saxena, S. K. Tripathy

"This study was carried out to understand the impact of variation in material morphology on the efficacy of microwave pretreatment. Three different types of mineral matter – coal, iron ore and manganese ore – were treated with microwaves at different energy levels, from 180 to 900 W, for different time durations of one to five minutes. The treated samples were subjected to microscopic, milling and liberation studies. Coal is a porous and amorphous material with low dielectric constant, and grinding of the microwave-pretreated coal samples resulted in an 18.18 percent reduction in the 80 percent of passing particle size, or d80, and a 17.1 percent increase in carbon recovery. The microwave-pretreated soft and friable manganese ore samples showed a 47.82 percent reduction in d80 during grinding and higher manganese recovery of 42.46 percent during liberation analysis. The microwave pretreatment and milling of hard and banded iron ore reduced the d80 by 20.83 percent, but no improvement was observed in mineral liberation. Coal showed better results during treatment at lower energy levels of 180 W for one to three minutes, whereas the minerals needed higher energy of 900 W for five minutes. Particle size analysis indicated rapid size reduction up to an energy input of 25 Wh. This effect diminished with increased energy input.IntroductionComminution is an important unit operation in mineral processing plants for the purposes of size reduction and mineral liberation. But most comminution technologies are energy inefficient and only a small amount of energy is consumed in real size reduction, with the rest wasted. High-grade mineral resources have been exploited on a large scale for the last century, and the upgrading of low-grade resources is now required to fulfill the needs of industry. Pretreatment methodologies for comminution will play a crucial role in the upgrading of low-grade mineral resources. Researchers have studied various pretreatment methods to develop an energy-efficient and techno-economically viable solution to improve mineral liberation and product fineness with minimum energy consumption. Most of these studies were focused on the use of chemical additives, thermal, ultrasonic and microwave treatment, and electric disintegration (Klimpel and Austin, 1982; Norgate and Weller, 1994; Gaete-Garreton, Vargas-Hermandez and Velasquez-Lambert, 2000; Wilson et al., 2006; Kumar et al., 2010; Wang, Shi and Manlapig, 2011; Singh et al., 2012)."

Jan 1, 2017

By Saghar Farajzadeh, Fatemeh Kazemi, Ataallah Bahrami

Spirals, the most common equipment for the separation of heavy minerals such as chromite, are greatly affected by size distribution and the liberation degree (hence the specific gravity and size) of the feed particles. In this study, the efficiency of spirals in separation of low-grade chromite particles has been investigated by studying the distribution of grade, size distribution and liberation degree of feed, concentrate, and tailings of spiral. For this purpose, mass balance constraints were applied to the spiral-containing chromite processing circuit. Afterwards, the grade variations and size distributions have been investigated. According to the results, when the feed to the spiral has a larger size distribution, the enrichment ratio of the feed is 1.32 and, with the smaller feed size, this value has increased to 1.99. When the spiral feed has a larger size distribution and higher specific gravity, the recovery of chromite increases with increasing particle size up to 250 microns, and then with increasing particle size, recovery decreases with a relatively steep slope. Evaluation of spiral efficiency with respect to particle liberation degree has also shown that despite the high degree of liberation of spiral feed in size fractions smaller than 75 microns (88.9%), the liberation degree of spiral concentrate and tail in this faction is equal to and less than that of feed, which can indicate poor spiral performance in these size fractions.

Oct 27, 2020

By S. A. Anzalone

The Helvetia copper deposit is a large undeveloped Laramide porphyry copper system located in the Santa Rita Mountains, Pima County, Arizona. This porphyry copper system consists of four areas of copper mineralization: Rosemont, Peach-Elgin, Broadtop Butte, and Copper World. Asarco refers to the four areas collectively as the "Helvetia Deposit". Mineralization and alteration are primarily contact pyrometasomatic, and zoning of hydrothermal alteration and sulfide mineral assemblages are similar to those observed at the Twin Buttes and Mission copper mines located approximately 32 km west of Helvetia. Asarco acquired the Helvetia Deposit in 1988 and has continued the exploration and development effort since then. A considerable amount of excellent geological work has been completed in the area but little information has been published on developments since the mid-1950's. The geology of the deposit as developed by numerous geologists over the past 75 years and the large, bulk tonnage low grade copper deposits outlined in recent years will be briefly reviewed in this paper.

Jan 1, 1992

By S. K. Pan, R. Venugopal, L. A. Kumaraswamidhas, Rakesh Prasad, Chandan Pandey

Cold compressive strength (CCS) and apparent porosity (AP) of pellets are essential properties regarding the burden of blast furnaces. The optimal required values for industries are 2.5 KN CCS and 21% AP. Blaine fineness and firing temperature are the decisive parameters analyzed here. During firing, microstructure phases such as silicate, hematite, and pore are formed. The phase’s grain density during induration influences the pellet’s CCS and AP. The influence of the factors over the response is evaluated by I-optimal (response surface methodology) design. Blaine fineness, firing temperature, pore phase grain density (PPGD), silicate phase grain density (SPGD), and hematite phase grain density (HPGD) affect the CCS and AP of pellets. The RSM-I-optimal predicted responses with a coefficient of determination (R2) of 0.89 for CCS and 0.91 for AP of iron ore pellets. Optimal conditions were Blaine no. = 1668 cm2/g, 1250 °C firing temperature, PPGD value 90 no/mm2, SPGD value 250 no/ mm2, and HPGD value 490 no/mm2, with 4.5 KN CCS 27%. The induration processes were investigated through statistical design of experiments for process optimization. Statistical analysis indicated the direct and interactive influence over CCS and AP. In this study, RSM-I-optimal modeling is used for iron ore pellets processing. The I-optimal prediction could be applied to make the process economical because information is obtained through fewer experiments.

Aug 18, 2020

By Ronald W. May

The Lower Cretaceous McMurray Formation in northern Alberta contains bituminous sands interbedded with other sediments which form the reject encountered during mining operations. Grade prediction is based on a combination of geological interpretation, computer modelling and past mining experience. In addition to estimates for ore, an accurate estimate of "waste" or "reject," are required for Mine Planning. This study investigates the ability of point-kriging using geostatistics, to augment the existing data base of drill-holes in a study area on Syncrude's leases. This approach enables the assessment of potential "worst" case - "best" case scenarios within the context of Mine Planning.

Jan 1, 1985

By Wolfgang Pietsch

DR iron') is a generic term for metallized product that results from the direct or solid state reduction of iron ore. In direct reduction, iron oxides are reduced to metallic iron in the solid state without an intermediate melting step. MIDREX ® Iron is the DR iron material produced in the MIDREX ® Direct Reduction Process. Except for some thermal and mechanical degradation, the external physical form of as-reduced DR iron is the same as the feed material. Chemically, oxygen associated with iron is removed leaving a very porous structure. Figure 1 is the scanning electron micrograph (SEM) of the internal surface of a MIDREX Iron pellet obtained from a Swedish oxide pellet during reduction at 760 °C. Figure 2 is the SEM of a polished and etched cross-section through the same pellet showing the amount of intraparticle porosity. As a result of this high porosity, apparent density of DR iron is relatively low, typically a¬round 2 g/cm3, and specific surface is extremely high, typically around 1.0 m2/g or more. Both density and specific surface depend on the raw materi¬al and the operating conditions of the direct reduction plant. Normally, more than 97% of the available iron is reduced into metallic iron with the rest mainly in the form of wustite (FeO). During direct reduction, the gangue in the iron remains essentially unchanged. Removal of oxygen and the corre¬sponding reduction in weight result in a slightly higher percentage gangue in the product than in the raw material.

Jan 1, 1976

This paper presents the results of column flotation of a fine feed sample of Florida phosphate. A central composite design is used to study the main and interaction effects of parameters affecting column efficiency. The statistical design is also used to determine the optimum conditions. The results indicate that, depending on the experimental conditions, it is possible to achieve a concentrate of high grade and recovery. A concentration of 15 ppm of non-ionic frother is found to be enough to maximize the recovery at the pH of 9.5.

Jan 1, 1999

By Rebecca Boakye, Zohreh Kazemi Motlagh, Virginia T. McLemore

The most significant uranium (U) deposits in New Mexico are sandstone-hosted deposits in the Morrison Formation (Westwater Canyon Member), where >169,500 short tons of U3O8 were produced from 1950 to 2002. In addition, >9076 pounds of vanadium (V, a critical mineral) and some molybdenum (Mo) were produced from these deposits. These and other U deposits (limestone-hosted, U-veins) in New Mexico also contain critical minerals. Critical minerals are mineral resources that are essential to our economy and whose supply may be disrupted; many critical minerals are 100% imported into the U.S. Some sandstonehosted, limestone-hosted, and U-vein deposits are elevated in heavy rare earth elements. One sandstone-hosted sample contained 0.3 ppm Re (critical mineral), 659 ppm Se and 408 ppm Mo. The arsenide five-element vein deposits in the Black Hawk district are mineralogically and texturally complex, low- to moderate-temperature, hydrothermal, structurally-controlled, Ag-Co-Ni-Bi-As bearing carbonate vein systems with local minor elements. Mineralized samples from Black Hawk contain up to 9970 ppm Ag, 8540 ppm As, 5690 ppm Co, 72,400 ppm Ni, 57 ppm Bi, 165 ppm Sb, and 32,600 ppm U.

Feb 22, 2026

By S. G. Malghan

Flotation is the primary method for copper minerals separation from porphyry ores. The need to process difficult-to-float porphyry copper ores presents challenges to engineers and scientists in several areas. This paper is concerned with summarizing generalized problems faced in the processing of porphyry ores and treatment methods to overcome the specific problems. Though some of the problems are interrelated the problems have been classified into three broad catagories. The case studies of some of the successful applications of innovative methods to solve problems related to ore mineralogy, metallurgical aspects of ore treatment and process variables show that quite often the problems are solvable by a judicious choice of flotation variables.

Jan 1, 1984

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

Many modern industries rely on rare earth elements (REEs) to produce products that are essential to both civil and defense applications. In a prior study (Vass et al., 2019), we showed that REE grades in acid mine drainage (AMD) and associated byproduct precipitates from AMD treatment (AMDp) warrant evaluation as a feedstock for REE production. The current work extends that effort through a broad survey of 141 AMD treatment sites in Northern and Central Appalachia. In this study, 185 raw AMD and 623 AMDp field samples were obtained and analyzed to assess the REE and major metal concentrations. Results show that an average of 282 μg/L and 724 g/t of REEs occur in AMD and AMDp, respectively. Additionally, both basins contained similar distributions of REEs, and these distributions tended to favor heavy and critical REEs when compared with traditional REE ore deposits. 

The Bureau of Mines has studied 260 underground coal mine fires which occurred from 1970 through 1989. Every fire had the capacity to be hazardous to life and property, however upon closer examination some were found to be inherently more dangerous than others. Our research involved reviewing and recording specific information contained in published Mine Safety and Health Administration fire accident reports. The objective was to determine if degrees of hazard relative to fire source or location could be construed from information contained in the reports. We specifically looked at the propensity for fires to cause injuries and fatalities as well as the need to seal the area in order to extinguish the fire. Relative to all underground locations, this review found that fires occurring in main haulage-ways were most likely to cause injuries and fatalities as well as require sealing of at least the immediate area to extinguish.

Jan 1, 1993

By R. M. Cox

Pneumatic coal loading and conveying systems provide alternative methods for the safe and efficient mining of the thin high-grade coal seams found in the Southern Appalachians. Pneumatic systems eliminate most of the health and safety hazards associated with the operation of conventional mining and haulage equipment in small low-coal mines by removing powered mobile equipment from the mine. Ventilation is also improved by the coincidental removal of gas and respirable dust from the mine by the operation of the pneumatic loading and conveying system. Other significant advantages of pneumatic coal recovery systems are relative simplicity, operating flexibility, low capital cost, quiet operations, environmental benefits, and ease of automation. The design considerations and field evaluations of experimental prototype pneumatic coal loading and conveying systems, installed and operated in small thin-seam mines, are presented in this report. In addition, fundamental design criteria and recommendations for the installation and operation of a variety of pneumatic coal loading and conveying systems are proposed, which offer alternative coal recovery systems that alleviate the serious health and safety concerns of current small mine operations.

Jan 1, 1999

By M. Fan, A. Hobert, W. van Dyk

Low flotation recovery and selectivity have been long-standing problems in the treatment of most ultra-fine phosphate ores. This paper investigates the improved flotation of two ultra-fine Brazilian phosphate ores from Itafos’ Arraias project. These ores are predominantly composed of quartz, muscovite, apatite and a Ca-Al phosphate. As a result of fine phosphate dissemination and associated grinding requirements, column flotation was selected for the metallurgical test program to address the inherent limitations of fine particle flotation using conventional flotation cells. Accordingly, both benchtop Denver cell and laboratory column flotation tests were conducted to optimize their respective flotation responses. Improved flotation performance was achieved using column flotation as compared to benchtop mechanical flotation. In column flotation, a P2O5 concentrate grade of 30.5-31.0% was yielded at a flotation recovery of 83.7-85.1% for the 38x0µm generated ultrafines. The benefits of Eriez’ column flotation technology realized from this study include a higher degree of selectivity, increased recovery, and reduced collector dosage as compared to bench-scale mechanical flotation.

Mar 2, 2022

By Peng Gao

Coal-based reduction followed by magnetic separation is an innovative technology used in processing refractory iron ores. Given that size is essential to the separation of the metallic iron from the gangue, the morphology of metallic iron particles and their evolution during coal-based reduction are investigated in the present work. The size of the metallic iron particle increased from 128.76 µm to 565.70 µm when the reduction time increased from 20 min to 60 min at 1,225° C and C/O (i.e., the amount of coal addition in terms of the gram-atomic ratio of the fixed carbon in the coal added to the combined oxygen in iron oxides) of 2.5. Based on our microstructural and metallographic analysis, the iron ore reduction process can be divided into three stages: (1) metallic iron particle formation, (2) iron oxide reduction and metallic iron assembly and (3) metallic iron particle growth. Almost all iron oxides are reduced to metallic iron in the second stage. These newborn metallic iron particles are energetically active and able to assemble and grow, and are eventually separated from the gangue. The large metallic iron particles benefit the subsequent magnetic separation process.

By John S. Wakeman

The initial step in the pelletizing of iron ores is the production of green balls. The importance of this step cannot be overemphasized as the physical quality of the green balls has a very significant effect on the subsequent induration process, regardless of the type of the indurating equipment employed. The ability of the green balls to withstand the rigors of handling, distribution, compaction and drying will have an effect on the degree of success of any pelletizing operation. Many factors affect the physical quality of the green balls including the prior processing of the iron ore, the characteristics of the balling feed and the type and quality of the binder used (if any). When working on the development of a new project or studying an existing operation, it is often desirable to determine what effect variations in these factors will have on green ball quality. It is generally impractical to make these determinations on a commercial, or even pilot plant scale, especially when the number of variables to be studied is large. Because of this, many organizations have developed batch techniques for producing green balls to enable them to perform such investigations with a minimum of time and expense. The batch balling method is at best, only an approximation of commercial balling systems. Many practitioners employ the use of pre-formed seed pellets to initiate a batch run. Thus, the growth mechanism encountered in any experiment is essentially snowballing. Unless an instability is introduced into a balling test (such as an excessive initial feed rate or an unusual feed material characteristic) the growth mechanism of coalescence is not present to a significant extent nor is it desirable. In a continuous operation, both mechanisms are present and necessary to sustaining the system. The batch balling technique thus produces pellets in an idealized manner and cannot be used to directly predict commercial green ball qualities. A general relationship does exist however, and the procedure is fairly sensitive to variations in test parameters. Although many refinements to this technique have been introduced over the years, batch balling is still essentially an art and subject to "operator effect". Therefore, to assure consistant and reliable results, skilled technicians who carefully adhere to established practice must be utilized.

Jan 1, 1971

By B. Schimm

Improve the mines productivity by simplifying the mining process, for these tasks the Wirtgen Surface Miner offers an attractive alternative. Surface Miners cut, crush and load material in one operation with only one machine. The cutting depth is controlled exactly.

Jan 1, 1997

By Basilio Giurgola, Federico Bonaiuti, Norbert Fuegenschuh

The North East Boundary Tunnel (NEBT) project in Washington, D.C. requires design and construction of several SEM adits which have to be built between lateral shafts and the NEBT-TBM Tunnel. The paper describes ground improvements, the actual excavation, and also the final lining works. Schedule and sequencing restrictions provided some unique challenges which had to be considered when designing and constructing these mostly short, but essential portions of the project

Dec 1, 2022

By Y. J. Wang

This paper deals with the application of linear programming to the solution of mine ventilation network problems which involve only the controlled splitting of air. An airway whose air quantity is to be controlled to a prescribed value is called a "fixed-quantity" airway. In a network where the fixed-quantity airways are increased in number and are distributed such that the air quantities for the remaining airways are uniquely determined by Kirchhoff's first law, the problem reduces to determining the head losses and locations for air regulators and fans. This is one of the network problems encountered most often in underground coal mines. By formulating Kirchhoff's second law as a set of linear constraints and the total air horsepower supplied by fans as a linear objective function which is to be minimized, the problem is analyzed through the technique of linear programming. Some important properties of the problem are discussed and examples are presented.

Jan 1, 1971