Search Documents

By Xie Junjie, Li Shina, Ma Ruixin, Min Changli, Yin Zichen, Li Kang, Shi Zhuonan

Cesium and rubidium were effectively separated by zinc ferrocyanide coprecipitation method, and the effect of precipitant addition amount on the separation of cesium and rubidium was studied. Under the conditions of Zn/Cs molar ratio of 0.45 and Zn/Fe molar ratio of 1, the precipitation rate of cesium is 84.01% and the separation factor of Cs/Rb is 164.65. The thermogravimetric curves of the sediment were measured, and the effects of roasting temperature, roasting time, and leaching liquid/ solid ratio on the extraction of cesium were studied. Almost all of the cesium was extracted under optimal conditions: roasting temperature of 600 °C, roasting time of 3 h, leaching temperature of 25 °C, leaching time of 0.5 h, and liquid/solid ratio of 5:1 mL/g. After the leaching process, the leach liquor with high concentration of cesium of 80.17 g/L was obtained. Finally, the leach liquor was further purified by solvent extraction, and the purity of the cesium chloride product reached 99.66%.

Mar 17, 2024

By Robert C. Cifelli

INTRODUCTION Background and Objectives Underground coal mining is a vital component of West Virginia's economy. However adverse environmental effects including ground subsidence and aquifer dewatering are often associated with such mining activities. Many families in northern West Virginia still rely on private water wells and springs for domestic water needs. In such areas where underground coal extraction and land subsidence have occurred, a disruption of the ground water flow system commonly exists with subsequent drainage of water to lower levels that may extent as deep as the mine workings; this causes loss of water supplies to landowners and represents a nuisance to mining companies 2 This report represents a summary of an M. S. thesis project in geology at West Virginia University by the senior author (3). The intent for this study was to document the effects of underground coal removal on ground water levels at selected mine sites in northern West Virginia, as observed from water wells, springs, and streams. This research should be useful to coal companies and regulatory agencies and aid in recommendations of future water well locations and specifications in areas of existing or proposed underground coal mines.

Jan 1, 1986

By Immo H. Redeker

The Kings Mountain area of North Carolina is the lithium pegmatite center of the U.S., if not of the whole world. We have two spodumene and by-product mineral producing companies, Lithium Corp. of America, and Foote Mineral Company. We also have Kings Mountain Mica and Kings Mountain Silica Companies producing mica. feldspar, quartz and clay from weathered pegmatites in that area. Figure 1 gives the location of the spodumene pegmatite area in North Carolina. The two spodumene producers mine typical pegmatite ore in open pits after removing amphibolite or mica schist overburden which is sold to aggregate producers. The ore reserves are discussed elsewhere in this session. They are in the order of plus 50 million tons but not unlimited. 1.2 The major minerals found and concentrated from the North Carolina spodumene pegmatite ores are tabulated on Table 1.

Jan 1, 1977

By Dave Southworth

After Abe Lee discovered gold (in April 1860) near the site of present-day Leadville, Colorado, he and is group staked nearly all of California Gulch with "speculative claims." They did so in an effort to grab any property that might be potentially profitable. But the plan did not work. New prospectors demanded a miners' meeting, from which arose the official "Bylaws of California Mining District, California Gulch, Arkansas River." These bylaws, adopted on May 12, 1860, established provisions as to the number, size and type of claims that could be filed. Fair laws invited more newcomers. By mid-summer, 5,000 people with tents and wagons were scattered from one end of the gulch to the other.Among the earliest arrivals to the region that spring were Horace Austin Warner Tabor and his wife, Augusta. H.A.W. Tabor, who was to become a pillar in the development of Leadville, arrived at California Gulch during a food shortage. He sacrificed his oxen so that hungry miners could eat. By doing so, he immediately became the friend of many. Augusta established a little store where she sold her baked goods and provided meals. Like most of the men, Horace prospected the surrounding hills. He only did so, however, for a short time. California Gulch yielded more than $5 million in gold during the next five years. By 1866, however, the placer gold was gone and most of the miners had packed up and left. Charles J. Mullen and Cooper Smith, who were grubstaked by a Philadelphian named J. Marshall Paul, found a new, rich lode at the Printer Boy Mine in 1868. It was the first underground gold mine in the Leadville area and marked the transition from surface mining to underground hard rock mining. Its discovery created a new but modest flurry of activity. Heavy black sand covered the region and made gold mining difficult. In 1875 William Stevens and Alvinus Wood decided to have the sand assayed. They discovered that it contained 15 ounces per ton of silver and was rich in carbonate. Stevens and Wood kept their find a secret for nearly two years. When the word spread in late 1877, the silver boom was on. In 1878 prospectors, merchants and others trickled into town from all directions. Dr. David H. Dougan closed his office. in Alma, crossed Mosquito Pass and set up shop in Leadville. Nobody seemed to need a doctor, however, and Dougan sat in his office for 28 days without a customer. On the 29th day he received word that there had been a mining accident and he was needed immediately. -That was the begin¬ning of his illustrious career in Leadville. Dougan was a successful physician, became mayor in 1881 and was later president of the Carbonate National Bank. Leadville was a simple community of log structures in 1878. By June of the following year, however, it had blossomed considerably. According to Cass Carpenter, as of May 1,1879, Leadville had "...19 hotels, 41 lodging houses, 82 drinking saloons, 38 restaurants, 13 wholesale liquor houses, 10 lumber yards, 7 smelting and reduction works, 2 sampling works for testing ores, 12 blacksmith shops, 6 livery stables, 6 jewelry stores, 3 undertakers and 21 gambling houses where all sorts of games are played as openly as the Sunday School sermon is conducted." Additionally, there were 36 brothels. When George E. King and other architects arrived, Leadville took on an air of elegance and sophistication. In sharp contrast to some of the Victorian-style, gingerbread-laced homes in Leadville, its suburbs were comprised of many tenement shacks and plain cabins mixed with a few commercial buildings, many mines and smelters. Mines sprinkled the area east of Leadville like pepper from a pepper shaker. Wherever there was a cluster of mines, a camp usually sprang up. Most were very close together. South of Leadville the giant Arkansas Valley lead smelter sprawled out between Stringtown and Bucktown in an area known as Smelter Valley. Founded in 1879 as the Billing and Eilers Smelter, the Arkansas Valley plant was operated by the American Smelting and Refining Company. Several other smelters operated in the vicin¬ity. In April 1878, Horace Tabor grubstaked prospectors August Rische and George Hook. For $64 worth of supplies and tools, he was guaranteed a one-third interest in their findings. Rische and Hook discovered the Little Pittsburg (often spelled Pittsburgh) Mine and made Tabor an instant millionaire. Tabor once purchased a "salted" mine, the Chrysolite; but instead of considering it a bad deal, he further developed the property and struck rich silver ore. Later, Tabor purchased the Matchless Mine for $117,000, possibly the only investment he made without partners. During its peak years, the Matchless yielded $1 million worth

Jan 1, 1998

By D. A. Norrgran, J. A. Wernham

Introduction In view of the continuing depletion of natural resources, requirements for energy conservation, plant optimization and hazardous waste management, and environmental consciousness, recycling and secondary recovery of materials are being developed with increasing interest Many secondary recovery processes are being developed that apply mineral processing technology. Gravity separation, magnetic separation and flotation have all emerged as explicit methods for recovering residual values from various process streams and hazardous constituents from waste streams. Recently, a technique for concentrating metallics has been successfully reintroduced. The concept of the alternating magnetic field eddy-current separator was developed over a century ago using rudimentary electromagnets (Patent 400317 issued to Thomas Edison on March 26, 1889). Widespread acceptance was, however, hindered by high costs, marginal results and poor economic incentives for secondary recovery. With the recent increased interest in secondary recovery and the development of high-energy rare earth permanent magnets, the eddy-current separator has now gained prominent acceptance. The separation forces imparted by an eddy current separator are the function of the magnetic field intensity and the alternating frequency of the magnetic field. The evolution of permanent magnets has provided a cost effective alternative for the generation of high-intensity magnetic fields. High-energy rare earth permanent magnets have substantially reduced the capital and operating costs over the electromagnetic circuits employed in antecedent eddy-current separators. Specifically, in recent years, the strength of permanent magnets has increased several fold with neodymium-boron-iron rare earth magnets now providing an energy product of 35 million gauss-oersted. Figure 1 shows the evolution in the strength of permanent magnets. The development of these rare earth magnets has led to the design of circuits possessing a magnetic force an order of magnitude greater than that of conventional permanent magnetic circuits. The eddy-current separator has been successfully applied in several metal sorting and recovery operations. Most common is the sorting of metal from shredded automobile scrap and municipal waste. With the advent of high-frequency, high-intensity magnetic fields, the separator has advanced to the point where it has direct application in the beneficiation of fine sized metals. Relatively fine sized (-1/4 in.) metal bearing slags and spent foundry casting sands as well as precious metal hearing electronic scrap demonstrate excellent metallurgical response to the eddy-current separator, and applications have progressed to finer materials and more selective separations. Theory Electrical currents are induced in all conductors when exposed to an alternating magnetic field. The induced current generates a magnetic field in the conductor that opposes that of the alternating magnetic field. Figure 2, is a schematic illustration of generated eddy currents. In this particular example, the alternating magnetic field is produced by a series of permanent magnets mounted on the circumference of a rotor. The permanent magnets have alternating polarity. As the rotor revolves, an alternating magnetic field is produced, and the rate of revolution determines the frequency of the alternating magnetic field. When a conductor, such as a metallic disc in the illustration, is placed in the alternating magnetic field, a closed loop current flow occurs. The current loop in the conductor produces a magnetic field that is a mirror image of the alternating magnetic field. At any point in time, the induced magnetic field in the conductor directly opposes the alternating magnetic field. This opposition of magnetic fields produces an instantaneous repulsion in the conductor. The conductor is consequently repelled from the rotor. The alternating magnetic field has no effect on nonmetallic materials as they pass through the magnetic field and discharge the rotor in a natural trajectory. [ ]

Jan 1, 1992

The 28th annual American Mining Hall of Fame Awards Banquet and fundraiser sponsored by the Mining Foundation of the Southwest will be held at the Marriott University Park Hotel, Tucson, AZ on Saturday, Dec. 4, 2010. The Mining Foundation of the Southwest is a nonprofit organization whose objectives are public education about the mineral industries, and recognition of outstanding accomplishments in and contributions to the fields of mineral and fuel resources. Funds are being raised to the support the foundation?s educational programs. Among these is the Educational Outreach Program operated jointly by the foundation and the Arizona Department of Mines and Mineral Resources.

Jan 1, 2010

By F. J. Sotillo

The objective of this investigation was to determine the feasibility of using a high-pressure roll mill (HPRM) to improve the separation efficiency of dolomite from apatite in downstream operations when treating high-dolomitic pebbles. High-dolomite samples from four phosphate mines were used for the test program. The research work plan included sample characterization studies; INSTRON tests to develop preliminary crushing data; high-pressure roll mill evaluations to determine crushing parameters, such as feed rates, rolls speed and gap, and applied torque, pressure and energy; and screen, microscopy, and flotation studies to assess dolomitelapatite separation efficiency. The results of the HPRM tests show that commercial products for all four mines can be obtained. Recoveries of 74-82% of the P2O5 and rejections of 46-83% of the MgO were reported with an specific energy consumption of 0.2-0.5 of that of a laboratory rod mill.

Jan 1, 1998

By Charles Dumaresq

The management of mine tailings poses a complex range of potential risks, including physical risks, such as the risk of catastrophic failure of a tailings facility and chemical risks such as the risk of long-term leaching of contaminants into the downstream environment. If these risks materialize, they can lead to a wide range of impacts on people and the environment, including human fatalities and severe impacts on downstream ecosystems, and the costs of recovery borne by industry, communities, governments, and society as a whole can be immense. Tailings facility failures in Canada (2014), Brazil (2015 and 2019), South Africa (2022), and in other locations around the world underscore how high the stakes are when mines produce and manage tailings (WISE Uranium Project 2019). Understandably, many people do not trust the mining industry to manage tailings responsibly. As an industry, it is our responsibility to manage tailings in a manner that is responsible and strives to minimize harm associated with tailings management, including effectively managing both the physical and chemical risks associated with tailings. Standards have an important role to play in responsible tailings management by setting expectations for standards of care and providing a means to measure and report on performance. In jurisdictions with strong legal requirements for tailings management, standards play a complementary role, pushing performance improvements in areas that may be difficult or impossible to address in legal requirements. In jurisdictions where legal requirements are lagging, standards may represent the de facto leading practice and may be the primary tool to help ensure responsible tailings management. Implementation of standards can help companies demonstrate that tailings are being responsibly managed and help build trust and credibility. Most importantly though, standards are important tools to help ensure that the risks associated with tailings are reduced, and that remaining risks are effectively managed. However, we must recognize that conformance with standards can have a down-side – the proverbial two-edged sword. Having standards is vital but there is a risk that implementing standards becomes a “box checking” exercise, with ongoing conformance leading to complacency. We must not allow ourselves to fall into the trap of believing that, just because we are complying with applicable standards and laws, we are therefore doing our best, and that “it can’t happen to us.” In addition, if conformance becomes the goal and the standard does not have mechanisms to drive continual improvement, then once the standard is met, there may be no incentive to improve. The point of complying with standards is not to pass the test. The point is to manage tailings responsibly, prevent catastrophic failures, and minimize harm. The point is to do better, because we must do better. To do that, we need to strive not for conformance, but for excellence in tailings management, driven by continual improvement and a quest to do better.

Feb 1, 2025

By M. Dayne Aldridge

A discussion of the definition of automation in mine ventilation applications is presented. The results of theoretical studies, experiments and practical experience from work in the United Kingdom, Belgium, Poland, the Soviet Union and the United States are summarized. Conclusions are drawn from these efforts and the prospects for the future development of automatic mine ventilation systems are explored.

Jan 1, 1978

By F. Calizaya

A booster fan is an underground ventilation device installed in the main airstream to handle the total quantity of air circulated to one or more working districts. It is installed in a permanent stopping and equipped with airlock doors, a monitoring system and interlocking devices between the main fan and the booster fan. When adequately installed, a booster fan can be used to reduce the main fan pressure, reduce leakage and decrease the power consumption. However, an inadequate installation can increase the likelihood of mine fies and recirculation of air contaminants. This study identifies hazards associated with the operation and maintenance of booster fans. It analyzes the accompanying risks and recommends control measures to reduce those risks to acceptable levels. The ventilation network of an existing coal mine was updated to include a booster fan. The hazards associated with the operation of this fan were identified, the risks analyzed and the esponse to each failure mode established.

Mar 1, 2014

By Takayoshi Otsuka, Taher Elsamni, Ashraf Bou-Krisha, Takaya Takimoto

"INTRODUCTION Tunnel is a closed space structure and it is necessary to ensure the sufficient time and route for safe evacuation for the tunnel users in case of a tunnel fire. In order to do so, damages and collapse of the tunnel linings and the secondary disasters can be avoided. Furthermore, the road tunnel is one of important infrastructural facilities and stopping its function for a long time for a tunnel fire could cause a great economic loss. Therefore, the tunnel structure shall be the one which can be repaired as soon as possible, and the fire protection methods need to be selected among those which enable the service to start as early as possible. The necessity of the fire protection works is evaluated for the tunnel structure with the consideration of the expensive tunnel construction cost and the economic effects of the tunnel service. Naturally, the fire protection works, which can protect the tunnel linings from the tunnel fire with small repairs, are inevitable. Design engineers of the fire protection works estimate the scale of fire from the degree of damages on the linings and its repair cost, the effect of fire extinguishers placed inside of the tunnel, the secondary disasters in accordance with the tunnel lining damages if any, and the ratio of fire protection cost calculated from tunnel operation cost. Based on this information, the engineers design the fire protection works according to the permissible limits Among the design cases of the tunnel fire protection in Japan, as shown in Table 1, there is no cases that used the fire temperature-time curve to design the fire protection works for large fire caused by vehicles catching fire. However, the most of cases used 30-60 minutes for fire duration based on the entry prohibition of dangerous goods carrying vehicles or the effect of early fire fighting. This paper will study the variation between different methods used for fire protection in road tunnel in Japan to evaluate them and try to found some recommendations. Especial l care will be attention to Polypropylenes (PP) which is starting to be applied lately."

Jan 1, 2016

By J. Gibson

"INTRODUCTION As one of the most pressing and important political debates of this century, climate change has captured global attention and is forcing governments to take action towards decreasing GHG and carbon emission levels below what was previously thought to be necessary. With the ever-increasing price of diesel fuel accompanied by the popular topic of carbon taxes and greenhouse gas emissions, the mining industry is looking to industry specialists for assistance. The benefits of a no-idle policy reach far beyond carbon reduction and fuel savings, ranging from decreased maintenance to increased engine life. With products like battery powered A/C systems and diesel-fired heaters, going no-idle is easier today than ever before. With both systems being manufactured to withstand the harsh environments of the mining industry, the end user will see a seamless change from conventional, inefficient belt-driven systems to future, stand-alone mobile equipment HVAC. THE HISTORY OF GHGS AND CLIMATE CHANGE In 1896 Svante Arrhenius first claimed that the combustion of fossil fuels may eventually result in enhanced global warming, but not until 1955 did Gilbert Plass draw global attention to global warming by summarizing that adding carbon dioxide to the atmosphere would intercept infrared radiation and thus warm the earth. Then in the early 1960’s Charles Keeling developed modern technology to produce concentration curves for atmospheric CO2 (Figure 1). In 1988 the Intergovernmental Panel on Climate Change (IPCC) was founded by the United Nations after acknowledgement of a rising global annual temperature. The IPCC consists of over 2500 scientific and technical experts from more than 60 countries, and because climate change could not be solved by a single country, the Kyoto Protocol was negotiated in 1998 requiring all participating countries to reduce their GHG emissions by at least 5% from the 1990 levels. The Protocol was signed by 186 countries in 2001 (since then several countries have retreated from the agreement, including the United States)."

Jan 1, 2015

By N. Magdalinovic

Generally speaking, erosion, as a process which entails degradation of surface layers of earth under the influence of the mechanical energy of surface waters, and from the point of view of biosphere sustainability, is a harmful process. This is absolutely true when agricultural and forest areas are concerned. However, if erosion is viewed selectively, this general definition about its harm raises serious questions. In other words, the erosion which takes place in the terrains where there is no vegetation because of the geological composition of the soil, does no harm. On the contrary, if the mineralogical composition of such terrains is characterized by a presence of precious and rare metals, erosion can be very useful. It contributes to the creation of new alluvial deposits of these metals in the waters in the plain land. It is here that torrents from hills come down and cause erosion. And finally, if there were no erosion, there would be no renewable deposits of gravel and sand.

Jan 1, 2007

By St. E. Deák

This paper focuses on maintenance of underground salt air curative quality using environmental friendly solutions. Possible ways to preserve its curative properties, in relation with the admissible salt air quality parameters, are analyzed. In situ investigations regarding microbiological impregnation in walls and the air inside the Romanian salt sanatorium were initiated. The results of a pilot project, which is in progress at Praid salt mine, are presented. After the end of the investigation at this site, investigations will continue in other Romanian salt mines, such as Slanic Prahova, Targu Ocna and Cacica.

Jan 1, 2006

By Yuexin Han, Wenbo Li, Xinran Zhu, Pengchao Li

A multi-stage fluidization magnetization roasting is a promising method to treat limonite ore. The dehydroxylation of limonite ore is a key reaction in the pre-heating stage. In this study, the dehydroxylation mechanism of limonite was studied in a laboratory fluidization roasting reactor. The samples were characterized using in situ X-ray diffraction, Fourier transform infrared spectroscopy, and simultaneous thermogravimetry and differential scanning calorimetry analysis. The phase transformation and kinetics analysis were studied. Results indicated that the dehydroxylation occurred at the temperature of 250–350 °C with the vanish of hydroxyl functional groups (-OH). The dehydroxylation kinetics followed the 2-D diffusion (Jander) reaction model G(α) = [1 − (1 − α)1/2]2, and the calculated activation energy was 113.43 kJ·mol−1. This study is conducive to exploiting limonite ore resources using magnetization roasting technology.

Nov 2, 2023

By Takashi Sasaoka

About 200 M tons of coal were imported into Japan in 2007 and Indonesia was its second largest exporter, accounting for about 30 M tons (12% of the total imported coal). Indonesia produced about 200 M tons of coal, about 75% of which was exported in 2007. As the Indonesian government has decided on an energy policy wherein 33% of the country?s primary energy demand will be met by coal by the year 2025, the domestic demand for coal has increased dramatically in recent years. Over 99% of the coal produced in Indonesia comes from surface mines. However, the conditions of surface mines are worsening each year: the stripping ratio is increasing, approaching the economic ratio, and the infrastructure for coal from inland mining areas is insufficient for such intense mining operations. To meet the demand for coal in Indonesia and the rest of the world, underground mines have to be developed. However, mining engineers and/or miners in Indonesia do not have a lot of experiences, expertise and know-how concerning the plans and operations of an underground coal mine. In addition, the industry faces a lot of problems which include poor conditions such as a steep coal seam, groundwater problem, stability of highwall, etc. Under these situations, a mine targeted in this research attempts to develop a new underground mine from an open-cut highwall because the stripping ratio in the surface mining area has almost reached the limitation of economic value. This paper discusses the possible development of a new underground coal mine from an open-cut highwall by means of field observation and numerical analysis.

Jan 1, 2009

By R. E. Thill

An ultrasonic, pulse-immersion apparatus and method are described for determining the effects of moisture on the dynamic elastic properties of rock. The method provides an alternative approach for assessing the moisture sensitivity of rocks. Ultrasonic wave velocities are continuously monitored in immersed rock samples as a function of water absorption and time up to saturation. Moisture effects on compressional wave velocity vary as a function of the type of rock and the time and amount of water absorption. Regression analyses are used to curve-fit plots of the data and to derive empirical expressions for compressional wave velocity as a function of water content for different categories of rock. Results indicate that compressional wave velocity can be used to predict both the moisture content and its effect on strength and deformational properties of rock. These results have potential for detecting or monitoring bad roof conditions in situations where the mine rock exhibits strength degradation with moisture absorption.

Jan 1, 1986

By John Newby, Ulf Gwildis, Ken Massé, Guillaume Roux

How to connect an effluent conveyance tunnel to riser shaft and diffuser arms of an outfall system is dictated by the ground conditions, which ideally include rock or soil strata of low permeability. Where such favorable conditions are beyond reach, both the complexity of designing and the risk of constructing this crucial system connection increase disproportionally. This paper describes the considerations that went into the approach of connecting a 5-m-diameter TBM drive with the in-river riser shaft of the Annacis Island WWTP New Outfall System in the highly permeable Fraser River sands at hydrostatic pressures exceeding 3 bar.

Jun 23, 2024

By Hongling Wang, DI WU, Shuai Li, Hui Shu

Isothermal reduction experiments on carbon-bearing pellets of copper slag were investigated by the thermogravimetric method with biomass carbon as a reducing agent. The results indicated that the reduction process of copper slag‑biomass composite pellets was dominated by gas phase diffusion, and the apparent activation energy was 88.44 kJ/mol. In the temperature range from 1000 to 1200 °C, the metallization rate of pellets increased with increasing temperature, and the maximum metallization rate was 78.4%. The optimal reduction temperature of CSBCP (copper slag-biomass composite pellets) was 1200 °C.

Nov 23, 2022

By H. M. King

A combination of chemical, statistical, geographic, and microscopic analyses reveal that sulfur in West Virginia coals is extremely variable in both form and abundance. Coals in southern West Virginia typically contain less than 1% total sulfur with organic sulfur being the dominant species. Northern West Virginia coals average about 2% total sulfur, mainly contributed by sulfur minerals. In addition to these regional trends, significant variations in sulfur form and abundance exist both vertically and laterally within individual seams. On both regional and local scales, the pyritic sulfur component can vary significantly in mineralogy, particle shape, maceral association, and particle size.

Jan 1, 1986