Search Documents

By D. Stone, R. Pakalnis, B. Seymour

Most mines using backfill routinely carry out quality control (QC) testing of backfill mixes with unconfined compression test cylinders. This is true for paste operations, hydraulic fill operations, and cemented rockfill operations worldwide. However, a large number of mines simply do not prepare and test the backfill samples in a consistent manner and fail to properly analyze or interpret the test results. Conventional concrete test criteria are not applicable given the differences in the mix constituents and the fact that a large number of the backfill QC test cylinders typically fail to achieve the target strength. Standard industry practices are needed to improve the analysis and interpretation of QC test results and to provide a better means of determining if the backfill is achieving its intended target strength. This paper will attempt to lay the groundwork for standard industry practices and will address several key questions raised by operators, such as how laboratory test data compares to in-stope performance, and how many QC tests should fail before a red flag should be raised. INTRODUCTION Although paste backfill is widely used throughout the mining industry, cemented rockfill (CRF) remains as the backfill of choice in places like Nevada where very poor ground conditions mandate the use of underhand mining. The safety and stability of undercut entries beneath backfill is a function of the quality of the cemented fill, which is typically assured through routine quality control testing. In the absence of a backfill quality standard, most mines rely on concrete standards to design and interpret their backfill quality control programs. In the USA, these standards are developed and published by organizations such as the American Society of Testing and Materials (ASTM) and the American Concrete Institute (ACI). However, the application of these standards to cemented backfills can be very difficult owing to the high degree of variability in backfill mixes and the resulting variability in test results. To illustrate, the concrete industry standards denote that an acceptable (passing) test result occurs when the average strength of the duplicate test cylinders exceeds the target strength and no single test result deviates from the target strength by more than 10% (ACI 214R). Remedial measures must be taken if three consecutive tests fail. With mine backfills, it is safe to say that these criteria are rarely achievable. A further, more dramatic example is the accepted coefficient of variation for concrete QC cylinders. According to ACI 214R, the coefficient of variation (CV) should range from below 3% (excellent rating) to above 6% (poor rating). However, if this analysis method is applied to several backfill QC databases from operating mines, coefficients of variation are calculated on the order of 50%. Clearly, there is a need to develop better industry practices for assessing the quality of mine backfill and to assist mine operators with the interpretation of test results and the development of action plans in the event of undesired outcomes.

Jan 1, 2019

By Robin J. Hickson

The Grasberg copper-gold deposit was discovered in the spring of 1988, one year before the planned closure of Freeport Indonesia's original Ertsberg openpit copper mine. In spite of Grasberg's remote location, 600 m (1968 ft) above the Ertsberg, atop a hitherto inaccessible mountain, Freeport-McMoRan brought its latest open-pit mine into production in the last week of 1989, less than two years after discovery. Freeport Indonesia's (FI) copper-gold mining operations are located in Irian Jaya, the easternmost province of Indonesia on the western side of the island of New Guinea. Fl's six ore deposits are all located within a 10- x 10-km' (3.9- x 3.9-sq mile) Contract of Work area. They are all between the elevations of 2900 and 4300 m (9515 and 14,100 ft) above sea level, some 96 km (60 miles) from the island's southern coast. A 118-km (74-mile) access route connects FT's port site of Amamapare on the Arafura Sea to the project area. The first section is an 18-km (11-mile) barge waterway. The final 100-km (63mile) is a two-lane gravel highway. The highway terminates 9 km (5.5 miles) beyond the FI townsite at the project's central mill, some 2850 m (9250 ft) above sea level. The mining areas are separated from the mill by a 780-m (2560-ft) sheer cliff face. The world's longest free span tramway system, with a total length of more than 1.6 km (1 mile), is the only means of access for men and materials between the mill and the surface mines. Weight restrictions for the tramway for equipment considered for the project are 15.4 t (17 st). The minimum clear width dimension of two tunnels along the portsite access road is 5.6 m (18.4 ft).

Jan 1, 1991

By R. Wensel

A composite material consists of two or more dissimilar components. These dissimilar components retain their identities when mixed together and contribute to the properties of the composite. A composite usually consists of two parts, the matrix and the reinforcing material, or extender that is added to the matrix. Typical materials used as the matrix in composites are metals, polymers, and ceramics. The reinforcing material can be added for any number of reasons. For instance, if the matrix is expensive, an inexpensive filler may be added to the matrix to lower the cost of the product without sacrificing properties. An example of this is calcite (CaC03) which is added to systems such as polyvinyl chloride (PVC), to lower the cost. Reinforcements may also serve as a means to enhance the properties of the matrix material. For example, carbon fibers are frequently added to plastics to increase their strength, and glass spheres may be added to plastics to improve flexural strength. Mg(OH)z is added to polymers to give the property of fire retardancy. The latter is the focus of this paper.

Jan 1, 1995

By Ping Li, Baokun Zhou, Lei Yang, Changfeng Li, Erhui Zhang

A uniaxial compression experiment was conducted on standard sandstone specimens to explore the sandstone’s mutation characteristics and early warning interval during deformation and failure. Meanwhile, acoustic emission (AE) and digital image correlation (DIC) techniques were introduced to realize multi-field analysis and cross-validation from the stress field, deformation field, and elastic wave field. The mutation characteristics of rock failure were investigated based on the cusp catastrophe theory. The results showed four mutation points in the destabilization process of sandstone: compressional density, yielding, destruction, and residual retention. As an internal activity characteristic of the sandstone failure process, AE directly reflected the dynamic failure process of sandstone. The stress variation was closely related to the evolution of AE characteristics. Sandstone loading failure was a process of the mutations of releasable elastic strain energy, dissipative energy, and releasable elastic strain energy. The mutation of dissipative energy was used as the starting mark of the sandstone warning state, and the second mutation of releasable elastic strain energy was used as the end mark of the sandstone warning state. Besides, the warning range corresponded to the loading time of 178 to 208 s. Finally, the sandstone instability warning interval was re-determined from deformation field evolution characteristics in the sandstone damage process, with a loading time of 180–204 s. This was consistent with the warning interval specified using the cusp catastrophe theory. The combination of AE, DIC, and cusp catastrophe theory revealed the mutation characteristics and early warning interval of sandstone failure. Hence, the results provide significant importance to predicting rock failure.

Aug 23, 2023

By Boris J. Kochanowsky

In the mobile crushing unit system trucks are replaced by a conveyor resulting in a "continuous" almost "fully-automated" operation with all its attendant advantages. In consequence, overall operating costs are greatly reduced. Because of the new designs of large mobile crushing units that have been brought on-to the market, the use of these plants has increased significantly during the last three years. This paper describes the designs of new mobile crushing units, and emphasizes the advantages that such plants offer to the rock products and mining industries. It examines operating costs, and indicates the conditions in which the application of these plants is most profitable.

Jan 1, 1968

By Simon T. Johnson, Robert J. Fowell

The application of roadheading and drag tool equipped machines requires an assessment of both cutting performance and tool consumption. Neither parameter can be assessed purely from compressive strength and tool consumption is often neglected, at a cost to the project. Results from in-situ monitoring show that a measurement of relative abrasivity using the Cercharscratch abrasivity test provides a basis for the assessment of tool consumption. This can be modified by also considering the effects of the machine specification and the rock mass quality.

Jan 1, 1986

By R. H. Roberts

The Environment Weipa is located at 12° south latitude on the west coast of Cape York Peninsula, North Queensland, Australia. The climate is tropical with most of the 1 600 mm. average annual rainfall falling between November and March. During the short winter months (May/ August) the weather is clear and pleasant, with temperatures seldom exceeding 27°C.Throughout the remainder of the year, conditions are frequently oppressive due to consistent high ambient temperatures accompanied by high humidity. The terrain is of low relief, and generally not more than 6 to 10m. above mean sea level adjacent to the coast. The coastline features numerous short estuaries which discharge run-off from the heavy rains collected by creeks and rivers. The whole area is covered by an open forest, the predominant species of which is Eucalyptus tetradonta. These eucalypts have only limited commercial value and are heavily infested with termites. Despite the fact that Weipa is close to the location of the first reported sighting of the Australian coastline by a European (William Janz - 1606), it remains very isolated. There is no developed road or rail connection to centres of population, so that transport of practically all products, personnel and materials to and from Weipa is by sea and air. Cairns (population 49 000) is 580 km. by air and 670 nautical miles by sea; Brisbane, the

Jan 1, 1977

By G. G. O. O. Uwadiale, M. A. Kollere, M. A. U. Nwoke

Birnin Gwari and Alawa graphite deposits were upgraded by flotation. Using 0.5 kg/t kerosene and 0.25 kg/t sodium silicate, flotation concentrates grading 90.7% and 88% Cg with recoveries of 86.2% and 84% were produced from Birnin Gwari and Alawa graphite samples, respectively. The combination of 0.5 kg/t kerosene, 0.2 kg/t pine oil and 0.25 kg/t sodium silicate yielded high-grade graphite (92.3% Cg) with a recovery of 83.9%. Flotation with refined rubber nut oil and kerosene, at a 1:1 ratio, produced a concentrate grade of 86.3% Cg with a recovery of 90.4%. With acid leaching of the flotation concentrate, a high-grade graphite concentrate containing 98% Cg was produced.

Jan 1, 1998

By Edwin B. Wilson

Electric power generation remains the greatest market for coal in the United States. In 1967, about 272 million tons of coal, amounting to over 51 percent of total coal consumption, were burned to satisfy this nation's hugh demand for power. The size of the utility market is currently five times that of 1941 and continues to grow with the demand for more and more energy. A major reason for this strong market has been the ability of the coal industry to supply a superior product for combustion while maintaining competitive prices. Now that the coal industry is engaged in intensive competition with nuclear power for future energy demand, it becomes ever more imperative that superior coal products are produced. One important problem when burning some coals is a liquid phase corrosive attack on boiler tube metal in the superheater and reheater areas of the furnace where steam temperatures may exceed 1050°F.

Jan 1, 1969

By I. Raposo, I. Moreno-Ventas, A. Palma, M. J. Díaz, M. Vázquez

The oxidative degradation kinetics of chalcopyrite have been studied by thermogravimetric analysis (TGA). The obtained data are necessary for the kinetic description of the flash fusion process, which can contribute to the optimization of the smelting process in copper extractive metallurgy. Activation energy (Ea) evolutions of the involved processes have been determined by several isoconversional methods; in this sense, the chalcopyrite oxidation processes could be adequately described, among studied models (E1641–16, Ozawa–Flynn–Wall, Kissinger–Akahira–Sunose and Friedman), by the Kissinger–Akahira– Sunose kinetic model. Using this method, Ea and A values are found to be very dependent on the conversion. Under lower conversion levels, higher Ea and A values have been calculated with respect to that found for medium and higher conversion levels.

By Robert W. Bruhn

Ground movements associated with high extraction underground coal mining, such as pillar retreat and longwall, are sometimes large enough to disrupt the ground water regime as well as damage buildings and other surface structures. A U.S. Department of Energy/Bureau of Mines- sponsored subsidence study currently underway at Kitt Energy Corporation's Kitt No. 1 Mine near Philippi (Barbour County), West Virginia has provided an opportunity to monitor the ground water response above a mine panel during both developmental and pillar retreat mining. The initial findings concerning ground water effects presented in this paper indicate that total extraction mining produced significant water level declines in deep-lying strata but had little effect on water bevels at shallower depths.

Jan 1, 1985

By Michael Casson

With the mining industry changing rapidly due to mergers, acquisitions and fluctuating market pricing, today?s market for coal, minerals, ores and aggregates demands electrical apparatus that perform every time with maximum efficiency and with consideration for personnel safety. This is especially true in existing mining operations where every payload counts. Draglines are the workhorses of surface mining operations, and reliable and efficient operation is absolutely critical to success. However, the inherent disadvantages of using dc motors and motor-generator (MG) sets can significantly impact productivity and return on investment (ROI).

Jan 1, 2013

By Sotiris Psomas, Colin M. Eddie

"Steel Fibre Reinforced Concrete (SFRC) Segmental Tunnel Linings have successfully been used for over 20 years in the UK and have been adopted in a number of high profile projects such as High Speed 1, Crossrail, Thames Tideway, as well as High Speed 2. Tunnel linings and especially SFRC design are not covered in the Eurocodes. This shortage of SFRC tunnel design rules seems to be partially addressed by several international publications. However, in the UK, the ‘design-assisted by testing’ (DAT) approach has also been adopted. The Paper discusses the UK’s best design practice and focuses on the DAT methodology as applied in the case of the 6.9km (4.3miles), 7.8m (25.6 feet) ID Lining for the £635million Lee Tunnel Project. The design approach, the full scale testing at the Building Research Establishment (BRE), and the construction innovations are presented. This experience will be transferred to the £4billion Thames Tideway Tunnel.INTRODUCTIONSteel Fibre Reinforced Concrete (SFRC) has been used for Tunnel segments for more than 20 years. The first application of SFRC in the UK was for the Heathrow Baggage tunnel (1994). Since then significant size tunnels have been designed and constructed, such as the Jubilee Line (1999) High Speed 1 (CTRL, 2006), Crossrail (2014), Lee Tunnel (2014) and the scheduled 25km Thames Tideway (‘Super Sewer’) and High Speed 2 rail tunnels. However one the main obstacles in achieving streamlined design and improving efficiency are the lack of appropriate design guidelines for SFRC tunnel segments. This issue will – to some extent – be addressed by a number of current documents on tunnel FRC design either being produced by BSi (PAS8810, expected 2016), ACI (544.R) and ITAtech (Design Guideline PCFRC, 2015) in an effort to advance the design of SFRC and take into consideration the recent developments in Steel and Macro-Synthetic FRC technology."

Jan 1, 2016

By Hossein Ghaedi, Hadi Fattahi

Despite the significant role of coal in the economic progress of nations, the occupational and health risks associated with its mining pose a major concern for industry stakeholders. The occurrence of roof collapses in coal mines remains a critical factor leading to substantial loss of life and financial damages for miners. Therefore, accurately predicting the roof fall rate (RFR) holds paramount importance. However, the uncertainty surrounding rock parameters in mines hinders the application of conventional methods to assess roof collapse rates in coal mines. To tackle the challenges associated with predicting roof fall rates in underground coal mines, this study proposes a novel solution by leveraging the Rock Engineering System (RES) method. The investigation is grounded in a dataset comprising 109 data points, encompassing crucial input parameters like depth of cover (DOF), primary roof support (PRSUP), intersection diagonal span (IS), mining height (MH), and coal mine roof rating (CMRR). In the model construction phase, 80% of the data (87 points) were utilized to build the RES model. A critical aspect of this study involves the evaluation of the RES model’s performance against alternative regression techniques, namely linear, power, exponential, polynomial, and logarithmic regression. This comparison was executed using the remaining 24 data points (20% of the dataset) for rigorous evaluation. Employing key statistical metrics such as mean square error (MSE), root mean square error (RMSE), and squared correlation coefficient (R2), the study systematically demonstrated the superior accuracy of the RES-based method compared to other approaches. In conclusion, the outcomes strongly support the efficacy of the RES method in predicting roof fall rates, not only in the specific case studied but also indicating promise for its application in other underground coal projects. This underscores the potential of the RES method as a reliable and versatile tool for forecasting roof fall rates in the complex and critical context of underground coal mining.

Mar 19, 2024

By J. Paraszczak

Water-powered jackleg rock drills, introduced recently in South African mines are reported to be more efficient, faster and more comfortable to operate than conventional pneumatic drills. A comparative testing of both drill types was performed in Quebec. Based on its results and time studies done in the mines, water-powered drilling has been reviewed with regards to drilling rates achieved, infrastructure needed, side effects, health and safety considerations. This study shows that the application of water-powered drills may help increase footage drilled and improve working environment, but under specific conditions. The examples of such applications are given in the conclusions.

Jan 1, 1995

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Colorado School of MinesResearchers at Colorado School of Mines (CSM) have developed computational fluid dynamic (CFD) models to study gas distributions and explosion and fire hazards in longwall gobs. In underground coal mines, methane continuously emitted from surrounding strata mixes with air from active mine workings and may form explosive gas zones (EGZs). Some western United States coal mines are also prone to spontaneous combustion (spon com). Insight into oxygen concentrations within the gob is crucial for assessing spon com hazards and mitigation strategies. Nitrogen injection used in conjunction with progressive gob sealing can reduce EGZs and spon com hazards by forming a dynamic seal that separates the methane in the gob from the air that ingresses from the face. This paper describes CFD modeling simulations studying the formation of such dynamic seals by optimizing the nitrogen injection locations. The impact of nitrogen on oxygen ingress and formation of EGZs is discussed. Optimum nitrogen injection quantities and injection locations were determined. Dynamic seal formation is most effective if the headgate nitrogen injection locations are split between the first crosscut inby the face and a second location about 300 m (1,000 ft) further inby. INTRODUCTION Underground longwall coal mine ventilation systems are designed to dilute hazardous gases and to provide breathable air to miners working in the area. Methane gas is liberated as the mining process extracts the coal and disturbs the surrounding strata. Methane mixes with the ventilation air and often produces explosive gas zones (EGZs) within longwall gobs (Brune 2013). Past CFD modeling research of underground coal mine ventilation systems has shown the effects of face air quantity on EGZs (Worrall 2012) and nitrogen injection to control spon com (Balusu et al. 2005; Ren et al. 2012; Ren et al. 2011; Smith and Yuan, 2008; Yuan and Smith, 2014). Other modeling approaches include network ventilation models of oxygen ingress (Dziurzynski and Wasilewski, 2012), and coupled Linear Network CFD algorithms (Wedding 2014). In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), CSM researchers are using Fluent®, a CFD software package by ANSYS, Inc., to model gas compositions and flows in underground longwall gobs. Figure 1 shows a progressively sealed gob with a U-type ventilation system in a three entry development. As the longwall advances, seals are constructed along the headgate in the crosscuts between the center entry and the gob. Additional gob isolation seals are built to block off the headgate entries inby the face. Nitrogen is injected through the seals in the first two crosscuts on the headgate side and at the first crosscut inby the face on the tailgate side, as shown in Figure 1."

Jan 1, 2015

By Stephen Njoloma, Ivan Hee, Ravi Jain, Mina Shinouda

"INTRODUCTION DC Water’s First Street Tunnel (FST) is comprised of a collaborative effort between DC Water, DC Water’s Project Consultants Organization (PCO) led by Greeley & Hansen and McMillen Jacobs Associates and the design-build team of Skanska, Jay Dee, and Parsons Brinckerhoff. The fast-track project includes elements that were designed by the PCO and released for construction by DC Water prior to Notice to Proceed (NTP) and elements designed by the Design-Builder from 30% to released for construction after NTP. This required effective communication and technical coordination for integrated engineering and efficient construction. The project, constructed in an urban residential neighborhood, included innovative construction methods such as multiple location ground freezing, utilizing a centralized freeze plant, to minimize community impact. The means and methods chosen for cast-in-place shaft linings, precast segmental tunnel lining, microtunneling, sequential excavation method (SEM) adits and near surface elements reflected the immediate and sensitive surroundings, which varied by construction staging area (CSA). Technical aspects of the project, relative to the evolution from pre-bid to construction documents, are discussed along with modified designs to suit means and methods. SCOPE OF WORK In 2012, four major storm events swept through the District of Columbia and hit the Northeast Boundary sewer shed particularly hard with the neighborhood experiencing severe flooding. The extreme nature of the flooding, the damage to private property, and the health risks associated with exposure to sewage led to a multi-agency response and community calls for answers and action. The Mayor assembled a Task Force to evaluate a range of potential actions to address combined sewer flooding including engineering, regulatory, code revision, and management improvements. The Northeast Boundary Neighborhood Protection Project was the outcome of the Mayor’s Task Force; it is a three-step infrastructure initiative designed to offload the undersized sections of the existing collection system that serves the Northeast Boundary drainage area by implementing the McMillan Stormwater Storage Project, First Street Tunnel Project and the future Northeast Boundary Tunnel Project. Until the Northeast Boundary Tunnel Project is completed, the First Street Tunnel Project will add 8 million gallons of combined temporary sewer storage in a new tunnel under First Street NW to relieve undersized sewers that traverse the Bloomingdale neighborhood."

Jan 1, 2016

By M. A. Girts

Wetlands can be constructed inexpensively on mined lands to treat small flows of acid mine water. Metals are removed from the water by the wetland vegetation and indigenous bacteria. Full-scale field tests initiated at over 20 mine sites during 1984 and 1985 indicate that water quality can be upgraded to meet discharge standards with relatively minor maintenance requirements. Iron concentrations of 25-85 mg/L in the influent water fall to less than 2 mg/L during flow through a small wetland. Manganese can also be removed, though somewhat less efficiently. At the discharge, pH is easily raised to 6 by flow over limestone.

Jan 1, 1986

By Muhammad Kamran, NIAZ MUHAMMAD SHAHANI

This study elucidates a new idea to predict mine fire levels by employing several machine learning techniques. A total of 120 patterns of various mine fire influencing parameters, such as oxygen, nitrogen, carbon monoxide, and temperature, were compiled from the Adularya coal mine in Turkey. Techniques like t-distributed stochastic neighbor embedding (t-SNE) and k-means clustering were used to process the data, and support vector classification (SVC) was executed to predict various levels of the mine fire. The results revealed that the proposed model has higher credibility to predict the various levels of underground mine fires.

Feb 14, 2022

By Jan Wolski

Increasing interest in the Bucket Wheel Excavator (BWE) technology calls for a universally understandable definition of suitable performance factors which would reflect the unique features of this technology. The importance of properly designed and calculated performance factors for the BWE systems cannot be overemphasised. They are used by all levels of management in any mining organization for a wide variety of purposes, in particular for budgeting, for selecting new equipment, for monitoring current equipment and for comparison with other operations.

Jan 1, 1984