Search Documents

By J. -M. Lopez-Cuesta, C. Petter, B. Otazaghine, M. Batistella, R. Sonnier

"Kaolinite is a dioctahedral aluminosilicate widely used as paper filler and coating pigment. At the best of our knowledge, kaolinite is not widely used in polymer industry. Therefore, in this study, the flame retardant effect of kaolinite in ethylene vinyl acetate copolymer (EVA) and polypropylene (PP) were studied and compared with an alumina trihydrate (ATH) and Talc. Cone calorimeter results shows that the weight percentage of ATH in EVA/ATH composites must be at least 50 wt. % in order to reach an improvement in fire retardancy in terms of pHRR. In the case of EVA/kaolinite, even with 35 wt. % the pHRR is largely reduced. Comparing PP/Talc and PP/kaolinite composites at 30 wt. %, both fillers leads to same reduction in pHRR with a slightly better performance for PP/kaolinite composites. In both cases an intumescent behavior of kaolinite composites was observed that could slow the rate of the rising degradation products, allowing radical recombination reactions. Also, it was observed that kaolinite forms a protective layer on the surface of the samples, which could insulate the material. These behaviors (intumescence and formation of a protective barrier) could reduce the transfer of the degradation products to the flame and explain the better performance of kaolinite composites. INTRODUCTION The use of mineral fillers as fire retardants in polymer matrix are well known and widely studied [1]–[10]. Aluminum and magnesium hydroxides (respectively ATH and MDH) are the most widely used inorganic fire retardants. To achieve fire retardancy with these mineral fillers, about 50-60% loading is required which decrease the physical properties of the composites. The fire behavior of composite EVA has been the subject of many studies [4], [7], [9]–[15]. EVA copolymers are commonly used in the cable industry, due to their high ductility, even at high loading rates. In such applications, the flame retardant systems should be introduced into the polymer to improve the fire reaction. Many flame retardant systems have been tested but the most used industrially relates to formulations based on hydrated mineral fillers (aluminum hydroxide and magnesium hydroxide). Their low cost and reduced fumes generation explains their success. However, to obtain good performance with this type of flame retardants, it is necessary to incorporate high levels (up to 65 wt %), which severely impact other properties such as processability and mechanical behavior. The main modes of action of these flame retardants are the dilution of the gas phase, the endothermic decomposition and a barrier effect created by the inorganic oxide residue which may be improved by the incorporation of other components such as montmorillonites, silicas or talcs."

Jan 1, 2015

By T. W. Meikle

Three nutrient amendments and a biological seed inoculant were evaluated for use in establishing vegetative cover on waste rock substrates. Randomized blocks were placed on three substrates. Treatments included two types of organic fertilizer, mineral fertilizer, Azospirillum bacterial inoculant, plus controls. The seed mix consisted of native grass species adapted to low nutrient conditions. Canopy cover has been monitored for three growing seasons. Results indicate: 1) two of three substrates support plant growth following amendment with organic fertilizers; 2) organic fertilizers increase cover substantially over mineral fertilizer; and 3) Azospirillum had no effect on canopy cover.

Jan 1, 1999

By J. J. Gusek

An 81 hectare (200 acre) tailings impoundment at a taconite operation in Wyoming that ceased operations in 1983 has been a source of blowing dust. The site qualified for reclamation under Wyoming's Abandoned Mine Land (AML) reclamation program. The ultimate reclamation construction included: incorporating commercially available organic amendments and fertilizers into a 300 mm (12 in) thick "cap" of a sterile clay loam cover material, lowering the water level in an adjacent flooded mine pit that was feeding uncontrolled seeps into the tailings basin, constructing a wide tailings pond spillway that allows flood control while minimizing seasonal water level fluctuations in the pond, and building rock berms and rock snow fences for wind erosion control and soil moisture preservation. Tree planting in the protective wind/snow shadows of rock berms and rock snow fences, and the plugging of a decant pipe are planned for future work.

Jan 1, 1998

By N. Myung, G. Hwang, H. Kim, Y. Han, S. Choi

"According to research presently being conducted on selective lithium recovery in seawater, inorganic adsorbents with high selectivity and capacity for capturing lithium ions from liquid lithium resources are called lithium ion-sieves (LISs). Their low toxicity, low cost and high chemical stability make LISs suitable for lithium recovery from seawater. In the present study, the ultrathin LMO nanofibers with controlled diameter were successfully fabricated by an electrospinning technique with a hypothesis that greater aspect ratio (i.e., smaller diameter) would lead to the enhanced recovery of lithium ion from seawater. Design of Experiment (DOE) and dimensionless analysis were performed to systematically optimize the diameter and morphology of nanofibers. Several complementary techniques including FE-SEM and XRD were used to evaluate the physical/physicochemical properties of the nanofibers. Lastly, the lithium ion recovery was tested for the nanofibers with different physical properties using lithium ion solution. INTRODUCTION Demand for lithium resources is increasing in many industries across the world.1-2 However, the conventional resources for lithium is very limited, and it even gets worse to secure the resources due to low grade and/or complexity of feed materials. Much effort has been, therefore, devoted to obtaining lithium from aqueous lithium resources. Several methods such as solar evaporation3-4, co-precipitation5, and solvent extraction6 have been proposed for recovering lithium from an aqueous lithium source, but there are limitations on its use; It takes a very long time or conditions such as temperature, pH and Mg/Li ratio are severe. Lithium ion-sieve (LIS) materials are considered as a good lithium adsorbent because of their unique chemical structure that can selectively separate lithium ion from brine and seawater.7- 10 Furthermore, their low toxicity, low cost, and high chemical stability make LIS suitable for lithium recovery from aqueous lithium resources. Spinel hydrous manganese oxide (HMn2O4) derived from spinel lithium manganese oxide (LiMn2O4) after topotactically extracting lithium from the spinel structure by acid treatment is most widely investigated LIS.10, LIS materials have been actively studied in various forms for easy handling and high efficiency (i.e. membrane11,12, foam13-14, granular15,16). Among them, the 1-D nanostructure LIS with high specific surface area is excellent in efficiency.9 In this study, we present the part of our recently submitted work17. Specifically, we fabricated systemically lithium manganese oxide nanofibers with different diameter as a lithium ion adsorbent using electrospinning technique through design of experiment (DOE). Enhanced lithium ion adsorption properties of the HMn2O4 nanofibers with different diameter were investigated in lithium liquid resources."

Jan 1, 2018

By W. W. McClintock

A column flotation system was designed to conduct release analyses of a very finely disseminated, stratiform, copper ore from the Denali Copper Prospect, Alaska. Chalcopyrite is finely disseminated in a carbonate matrix and pyrite is disseminated in both the chalcopyrite and gangue, requiring grinding to 20 microns for adequate liberation. A 25 mm x 2.4 m glass flotation column was designed. The ore and its flotation tailings were repeatedly floated to obtain a rougher concentrate, which was repeatedly floated to produce release fractions. These were analyzed for copper, iron calcium and magnesium. Release curves were plotted. The procedure was replicated at each of two grinds; 99% and 88% passing 37 microns (400 mesh), and should find application for flotation characterization and process selection. Bond grindability work was also conducted.

Jan 1, 1994

By X. P. Zheng, H. K. Lin

Barium fluorophlogopites were synthesized in the laboratory to investigate the effects of composition and crystal parameters on surface properties and floatability. The negative surface charge of mica is determined by the barium content, the crystal cell volume, the distance between the layer structure and the Ba-O bond length. The higher the barium content, the larger the cell volume and distance between the layer structure, and the longer the Ba-0 bond, the more negatively charged the surface is, and, hence, the more easily adsorbed are cationic collectors. When an anionic collector (sodium oleate) is used, barium oleate forms on the mica surface and hence chemical adsorption occurs.

Jan 1, 1995

By D. Weston

During recent years there has been a great deal of confusion in the North American mining industry with the introduction of new comminution terminology and claims (without substantiative evidence), for various types of equipment in this field. The authors will attempt to clarify the terminology used, and where possible, give illustrations of plant practice with actual operational and pilot plant data. This is considered necessary in order to obtain a clear picture of the comparison of such equipment to the revolutionary change that the Aerofall Mill has brought to the mining industry.

Jan 1, 1964

By G. Biles

The Eskay Creek Mine, a high-grade gold and silver underground mine in northwestern British Columbia started operations in late 1994. For the first three years of operation, ore was crushed to minus 2 inch; blended to satisfy smelter terms and direct shipped to smelters in Japan and Canada. Before commencing the above operations, preliminary evaluations had indicated that an extremely complex metallurgical facility, requiring a large capital investment, would be required to recover the precious and other economic metals. Subsequently markets for raw ore were identified and underground mining and ore transportation operations, at a nominal production rate of 300 tonnes per day, were commenced. Exploration diamond drilling in 1995 and 1996 discovered additional lower grade mineralized zones, which are less economic or uneconomic as direct shipping ore. Testwork demonstrated that these lower grade zones could be upgraded to marketable concentrates in a simple flotation mill. The mill was built in 1997 and has been in operation since late 1997. The mining rate now has increased to 400 tonnes per day including 250 tonnes per day of the direct shipping ore and ISO tonnes per day of the mill ore. Prime Resources Group Inc. wholly owns the Eskay Creek Mine. Homestake Canada Inc. owns 50.6% of Prime's shares and manages and operates the mine on Prime's behalf. This paper discusses the mining and milling operations as well as ore shipment and smelter contracts' administration.

Jan 1, 1999

By P. Amelunxen

Over the past several years, the combination of higher energy and steel costs and the recent commercial deployment of high-pressure grinding rolls (HPGR) technology in hard rock mining have led many multinational mining companies to evaluate the suitability of HPGR technology for their particular comminution circuits. HPGR technology is perceived to require a higher capital investment while delivering lower long-term operating costs. This paper undertakes a critical evaluation of this perception. By evaluating the capital and life-of-mine operating costs of competing circuit designs for soft, medium and hard ores, the HPGR break-even point can be identified, at which the incremental capital cost of an HPGR circuit is equivalent to the net present value of the projected operating cost reductions. For ores with hardness parameters above the break-even point, HPGR circuits could offer economic benefits, while for softer ores, SAG mill/ball mill/pebble crushing (SABC) circuits are likely to be more economical and energy efficient. This evaluation considers both an SABC reference circuit and a traditional stage crushing configuration. Other influential factors are also discussed.

Jan 1, 2011

By J. P. Bunch

As the number of environmental laws continues to steadily increase and the economic penalties for contamination problems become more severe, environmental management represents an important management function within today's U. S. mining industry. The economic impact to a mining company for contamination is not only realized in legal fees and fines but also in the cost of doing normal business. For example, a mining company with contaminated property applying for a loan may be refused because of a lending institution's reluctance to finance due to liability concerns. Or, an insurance company may decide to greatly increase its annual premiums because of existing or potential contamination problems. One of the main duties of the environmental manager is to seek ways to reduce these types of problems by eliminating contamination or by knowing what problems exist and designing corrective measures to prevent the situation from worsening.

Jan 1, 1990

By Yongsik Jeong, Kwangmin Kim

Conventional tailings slurry contains a significant amount of water, and water management is key to ensuring the stability of a tailings storage facility (TSF). Simply reducing the water content in the slurry before discharging it from the mill could be an effective way to improve TSF water management. This study investigated the potential for using an environmentally friendly polymer as a new drag reduction agent (DRA) to reduce frictional pressure loss and also conserve water. It entailed conducting pipe loop tests to assess the polymer’s effect on pressure loss in tailings flow and then applying the test results to validate a numerical model using computational fluid dynamics (CFD). The model was also used to determine the polymer’s optimal concentrations at given solid concentrations and flow rates, its effect on energy efficiency for tailings transportation, and its potential for saving water. A case study for a mid-sized, hard-rock mine with a throughput of 50,000 t/day found that the solid concentration could be increased from 30 to 45% with no pressure loss by applying 1996 m3 of the polymer per day. Adding the polymer also resulted in water savings of 57,552 m3/day. The results of this study demonstrated the potential for using the new DRA not only to improve TSF stability but also to save water.

Jun 29, 2020

The future phosphate rock deposits in South Florida contain a significant fraction of dolomite. The high MgO content of the rock is undesirable in the production of phosphoric acid. Several flotation schemes have been attempted to separate dolomite from phosphate rock. Alternately, Selective Flocculation process has been suggested to separate dolomite from apatite. A high MgO content rock was simulated by a 30:10:60 synthetic mixture of apatite, dolomite and silica. Single mineral selectivity was observed in the mixed mineral systems apatite-silica and dolomite-silica with Polyacrylic acid (PM) and Poly(ethylene oxide) (PEO) flocculants respectively but not realized in apatite-dolomite system with PEO flocculant. Heteroflocculation, suspected to be the major reason for loss in selectivity, was minimized by addition of a Site Blocking Agent (lower molecular weight fraction of PEO). Process parameters such as size reduction schemes, flocculant/SBA dosage, and pH were investigated to achieve the desired separation. The selectivity obtained in binary mixed mineral tests was translated into the ternary mixed mineral system, viz. apatite-dolomite-silica. In this presentation surface chemical characterization of the samples and their flocculation behavior will be discussed.

Jan 1, 1994

By D. Boreck

The Bureau of Mines is conducting research on the feasibility of incorporating in situ stope leaching into active underground metal mines. Stope leaching, a modified in situ leaching technique, proposes to recover metals by leaching fragmented ore in existing underground openings and collecting and processing the metal-bearing solution to recover the valuable metals. If leaching solutions escape from the stope, either through geologic discontinuities or highly permeable zones in the rock, valuable metals dissolved in the solution may be lost. Escaping solutions may also contaminate ground waters. Consequently, in fractured rock, the characteristics of the fractures in the vicinity of the leaching stope must be understood before introducing actual leach solutions into the stope. Effectively characterizing a rock mass requires the integration of several disciplines including structural geology, borehole geophysics, hydrology, geochemistry, and mining engineering. This paper will focus on the general geologic and geophysical techniques that can be used to characterize the rock mass at an underground simulated stope leaching site. The results of several geophysical logging methods, tested at the site, are compared to the geologic core descriptions. Then, the? effectiveness of the different geophysical techniques in delineating fracture zones will be assessed. Knowledge gained through the geologic and geophysical analyses can be used to supplement results from hydrologic testing. This information can also be utilized in designing blast patterns and developing strategies for controlling or blocking movement of escaping leach solutions.

Jan 1, 1991

By Christopher Newman, Andrew Minckley

With underground stone operations developing in deeper and more geologically complex conditions, accurate pillar stability analysis becomes for the evaluation of engineering design. This paper provides engineering-based recommendations for applying LaModel to evaluate multiple-level room-and-pillar stone mines in both shallow and deep cover. It provides practical guidance on model calibration using field observations, selection of input parameters, and interpretation of results to inform design and operational decisions. The analysis demonstrates LaModel’s effectiveness in simulating pillar load transfer, stress redistribution, and failure mechanisms in complex mining geometries where empirical methods may be inadequate.

Feb 22, 2026

By Z. Scopa, E. Tarshizi, R. Setterlind, L. Frost, R. Livernois

"THE MINES OF THE FUTURE The mines of the future present a host of challenges, which may appear exciting or daunting depending on one’s perspective. Whether some sectors of the public recognize it or not, the demand for raw resources is not going away any time soon. In fact, it is rising as global population grows, urbanizes and attempts to steadily increase quality of life. Yes, at the same time that much of the highly developed world is calling for greener goods, reduced consumption, and cleaner production, in other areas there are cries for clean water and sanitation, consistent energy supply, access to health care and education, personal security, and support for basic human rights. The balancing act for sustainable development of our global society is indeed precarious, and the mining community is necessarily a key player. Fortunately, many industry members have accepted this role and the responsibility to provide leadership and a solid foundation for progress. Looking ahead, we need new generations of leaders, many of whom will be mine engineers, which are ready to tackle all sorts of complex problems. There are tremendous needs just for technological innovations. Increasingly tough deposits will require that we continue to expand scale toward “super” pits and “deep” underground mining fully develop unconventional recovery techniques like in-situ leaching and gasification or deep-sea extraction, and seriously consider off-earth endeavors. Such work will take entirely autonomous equipment; novel separations, processing and recycling methods; and systems that can withstand extreme physical conditions – just to name a few. It will also take a level of systems integration never-before seen in our field, complete with big data issues, sophisticated analytics and modeling efforts, and cyber-security challenges. Moreover, increasingly complex environmental problems will require creative solutions. Addressing issues like pollution control across multiple media, emerging contaminants, optimal management of wastes, selective mining, and shared use of resources between mine operations and surrounding communities and ecosystems are among top priorities. Really, a complete paradigm shift must occur, such that our focus is on overall improvement of environmental conditions, rather than minimization of impacts. A similar shift will be required in the social realm. How can we make miners safer and healthier on-site and off? How can we contribute to communities such that they are better off, now and long-term, for having a mine next door? How can we help transform artisanal mining practices to also contribute to sustainable development? How can our work be a factor in increasing economic and political stability? How can we improve the public understanding of raw resources and the need for mining enterprises?"

Jan 1, 2017

By R. M. Hernandez

The Bureau of Land Management (BLM) constructed four passive biochemical reactor systems (BCRs) to treat mining influenced water (MIW) in the Bunker Hill Superfund area near Coeur D?Alene, Idaho between 2002 and 2003. Initially, the BCRs operated very effectively. However, in the past couple of years, the zinc removal effectiveness of the four BLM BCRs has declined [1]. The central objective of this study was to characterize the microbial communities and substrate present within the BLM BCRs and to use these factors to propose strategies to promote sustained sulfate reduction levels. Microbial communities were characterized by quantifying total bacteria and sulfate reducing species. Substrate was characterized by quantifying the percent organic, acid soluble organic, acid insoluble organic, and bioavailable material within the BCR. The results suggest the depletion of bioavailable organic substrates is the primary cause of the decline in zinc removal and not the microbial community structure. The ability to assess the amount of bioavailable organic substrate and microbial community is important to the understanding of the sulfate reducing capacity of the BLM BCRs and developing strategies to facilitate performance enhancement of the current BLM BCRs. The characterization of organic substrate and microbial community structure are also important to improving design of future passive treatment systems for mining influenced waters.

Jan 1, 2010

By Tsunenori Shibata, Kazunori Jimbo, Kaoru Toya, Masafumi Matsumoto, Jinya Mitsui, Toshinori Tsuji

"The Toyama Line is under construction as a natural gas pipeline with a length of 102 km from Itoigawa City to Toyama City. A 2 km-long tunnel section of the pipeline that we are reporting here is being excavated in a mountain area away from an urban area. The geology under which the tunnel is constructed is collapsible fractured breccia slate and Holocene sandy soil. Other tunnels of the Hokuriku Expressway and Hokuriku Shinkansen are in service above the tunnel route. From the starting shaft on Toyama side, conventional tunneling was adopted to facilitate excavating the base rock layer and maintain enough distance from the Hokuriku Expressway tunnel. From the starting shaft on the Itoigawa side, TBM tunneling was adopted to cope with the unconsolidated soft ground for a 200 m-long section from the shaft. We will discuss the issues and countermeasures concerning the selection of a tunnel route and excavation methods, performance of both conventional and TBM tunneling, and underground connecting of these tunnels excavated by conventional (NATM) and TBM methods under a high groundwater pressure up to 1.2 MPa. INTRODUCTION AND BACKGROUND The International Petroleum Exploration Teiseki Co., Ltd. (INPEX) is constructing a high-pressure main pipeline network in the Toyama Prefecture area to promote the use and reliable supply of natural gas as shown in Figure 1. As part of the Toyama line project that has a total length of 102 km, A-1 construction, the nearest section to the tunneling starting point in Itoigawa City, where various tunnel excavation methods have been adopted to install the high-pressure pipeline 20 inches in diameter, a 2 km tunnel in the A-1 construction section discussed here is to be excavated by conventional and TBM methods in a mountain area. Based on environmental studies such as traffic jams due to frequent traffic of heavy vehicles disposing of soil, and the effects of dust, noise and vibration during construction, we selected the route to install the gas pipeline in a mountain area as shown in Figure 2, where the impact on the surrounding environment could be minimized."

Jan 1, 2016

By D. D. Harbuck

The U.S. Bureau of Mines investigated germanium and gallium extraction from an ore containing 0.089% Ge and 0.036% Ga. While previous researchers concluded that a reducing agent such as 502 is needed to extract germanium and gallium from such ore, this research showed that high extractions (87% Ge, 97% Ga) were possible using sulfuric acid alone, if the acid concentration were properly controlled. This control was achieved using a two-stage counter-current leach circuit. Microprobe analyses revealed that the non-extracted germanium is in solid solution with quartz, and therefore cannot be leached with 502 or sulfuric acid.

Jan 1, 1991

By D. R. Nagaraj

Secondary Ion Mass Spectroscopy (SIMS) was used to study copper ion adsorption, and its effect on subsequent sulfide collector adsorption, on pyrite and pyroxene minerals under flotation related conditions. Copper was found to adsorb on both of these minerals and cause enhanced sulfide collector adsorption. The distribution and depth profile of copper and collector on these mineral surfaces were obtained by using SIMS in the imaging mode. The results of this study have provided a valuable insight to understanding pyrite and gangue flotation observed frequently in operating plants.

Jan 1, 1995

By M. J. Meulendyke

An extensive program of marked ball wear testing (MBWT), laboratory corrosion studies, and worn ball surface analyses has been used to gain insight about the role of corrosion in the overall wear process. In some environments, localized corrosion is observed; the actual wear mechanisms in such cases are pitting/spalling and abrasion. Factors affecting the occurrence of pitting include the abrasiveness of the ore, corrosivity of the slurry, corrosion resistance of the media, and galvanic coupling effects. Elimination of pitting substantially improves overall wear resistance. When pitting is not observed, the contributions of general corrosion are significantly less.

Jan 1, 1984