Search Documents

By H. B. Oblad

Coal/pyrite fines were froth floated in a laboratory cell to examine the rate of pyrite recovery during conventional coal flotation. The effects of collector, particle size and carbon to total sulfur ratio on the kinetics of recovery were investigated. These data coupled with microscopic examination suggest that miniscule amounts of coal that remain attached to the pyrite surface affect the rate of flotation of pyrite.

Jan 1, 1985

By Avula Rajashekar Yadav, Sreenivasa Rao Islavath

Barrier pillars and gateroads play a vital role for the safe exploitation of coal from the panel in the longwall workings. The barrier pillars and gateroads are subjected to the front abutment and side abutment loads during the retreat of the panel. These structures may fail if the developed load on them is higher than their strength. The stability of the longwall structures such as barrier, gateroads and face is paramount in extracting the coal from the panel safely. For this, a deep longwall mine in India is chosen for the study using a 3D numerical modelling technique. In this paper, three critical conditions such as scenario 1 (no side goaved-out panel), scenario 2 (with side goaved-out panel) and scenario 3 (with two side goaved-out panels) are taken. For each scenario, five retreat distances such as 100, 125, 150, 175 and 200 m are considered for detailed investigation. The development of vertical displacement in gateroads, vertical stresses on barriers, vertical stress concentration factor, abutment zone and yield zone for longwall face are extracted and analyzed. Also, the safety factor of the barrier and longwall face is estimated considering the Hoek–Brown rock mass failure criterion. From the study, it is observed that the maximum vertical displacement of 121 mm in TG3 at scenario 3 for a retreat distance of 200 m and a minimum vertical displacement of 33 mm in TG2 for a retreat distance of 100 m at scenario 2. The development of vertical stress on the barrier is found to be between 8.78 and 13.40 MPa, and the safety factor of the barrier lies in between 1.56 and 1.80. The study also revealed that the yield zone at the longwall face lies within 2 to 3 m.

Dec 29, 2023

A comparison of gold, platinum and sulfide ion selective electrodes was made in this investigation for determination of Eh in solutions containing sulfide ions as a model system. The comparison was made in terms of the accuracy of the measured response, response time, pH dependence, and reproducibility of measurement. In addition, the sensitivity of each electrode towards changes in sulfide ion concentration was measured in terms of the change in measured Eh per decade change in concentration of sulfide ions. On the basis of a detailed investigation of the electrode processes occurring at the surface of gold and platinum electrodes, it was postulated that within the pH range investigated these electrodes respond to changes in the hydrosulfide ion, HS-, concentration in solution. In comparison, the sulfide ion selective electrode is known to respond to changes in the sulfide ion, S-, activity in solution. Although the potentials measured with gold and platinum electrodes were mixed potentials, pretreatment procedures can be used to obtain a signal suitable for process control. For control of sulfide ions in flotation pulps, the use of a gold electrode pretreated at 1.0 V with respect to a standard hydrogen electrode is recommended.

Jan 1, 1990

By Rob Thomas

It is generally agreed that standing support should be installed in roadways that will for various reasons, be holed through with a longwall. Considering the magnitude of the associated abutment loading in conjunction with the need to ensure that the material used is cuttable, some form of cementitious support is often used.

By J. B. Davis

Isotope analyses distinguish biogenic sulfur ores from non-biogenic ores, but do not distinguish bioepigenetic from biosyngenetic ores. Sulfur deposits of salt dome caprocks and of bedded Permian evaporites of west Texas, however, are clearly bioepigenetic. Anhydrite, introduced by salt diapirs into geologically younger sediments, is converted biogenically to sulfur and calcite in the presence of petroleum; for example, in Challenger Knoll, a salt dome at a water depth of 3600 m in the Gulf of Mexico. Bedded evaporites of west Texas in association with petroleum show an obvious epigenetic replacement of the anhydrite layers by biogenic sulfur and calcite

Jan 1, 1978

By Jim V. Rouse

Adverse water-quality impacts of uranium mining and milling activities on both surface- and ground-water resources in the Grants Mineral Belt have recently been documented.1 In some cases, the impacts resulted in violation of existing regulations and license conditions and have endangered public health. Unfortunately, industry-sponsored ground-water monitoring programs do not adequately record the actual impacts of mining and milling on ground-water quality.

Jan 1, 1976

By R. B. Tippin

Great Salt Lake Minerals & Chemicals Corporation (GSL), a subsidiary of Gulf Resources & Chemical Corporation, is located on the east side of the Great Salt Lake, approximately 20 miles from Ogden, Utah. GSL processes brine from the north arm of the lake to produce potash, salt cake, salt and magnesium chloride brine. Potash fertilizer, in the form of K2SO4 is GSL's primary product. The GSL Sulfate of Potash Complex The GSL potash complex (depicted in Figure I) is divided into a solar evaporation pond system and the process plants. The solar,evaporation system consists of a 17,000-acre (68.8 Km2) ponding operation where the various salts deposit during the summer evaporation season, and a harvesting operation which recovers the deposits during the remainder of the year. The harvest is either preconcentrated in the flotation plant or processed directly in the chemical plant where sulfate of potash (SOP) is produced. The chemistry of the lake brine results in a solar deposit con¬taining primarily kainite (KCl-MgSO4.3H20), schoenite (K2SO4?MgSO4^ 6H2O), and halite (NaCI), with some carnallite (KCl.MgCl2.6H20) and epsomite (MgSO4.7H20). Other minor minerals may be deposited, depending upon the weather during the evaporation season. Each year, the solar deposit in the evaporation ponds will greatly depend upon the summer weather conditions, which have in the past proven to be quite unpredictable. Weather may alter both the quantity of the solar deposit and the composition of this deposit. During, a "short" evaporation season, the tonnage deposited decreases, but depending upon the short-term weather, the potash mineral content

Jan 1, 1977

By James T. Baxter

Underground mining of limestone is becoming increasingly attractive in Illinois. Most quarries are near rivers on the western and southern borders where competition for land use is intensive. Increasing demands for stone can be met by expanded mining with access by edits in existing quarries and by inclines and shafts at downdip sites. Geologic, hydrologic, and engineering conditions indicate that deep mines in the Ste. Genevieve, St. Louis, Salem, Ullin, and basal Burlington Limestones of Mississippian age and in the Moredock Limestone Member of the Dunleith Formation of Ordovician age are possible, but development will require prudent exploration and planning to ensure that the product will be of good quality.

Jan 1, 1978

By John A. Haggman

Philippines is a country that is richly endowed in mineral wealth. In 1988, Climax Arimco Mining Corp. (CAMC) geologists found the Dinkidi porphyry gold-copper deposit in Nueva Vizcaya province. It is the most significant mineral discovery in that country in recent times. To date, the company has defined indicated resources of 124 Mt (136 million st) of 1-g/t (0.029-oz/st) gold and 0.4% copper. This includes a high-grade core of 7.9 Mt (8.7 million st) of 6-g/t (0.175-oz/st) gold equivalent. Total contained metal is 124.4 t (4 million oz) of gold and 499 kt (1.1 billion lb) of copper. Dinkidi's discovery resulted from initial geologic reconnaissance and recognition of the intrusive complex that is exposed at surface and anomalous in its topographic expression. This was followed by systematic exploration. This includes extensive gradient array induced polarization (IP), ground magnetics, geochemical sampling and diamond drilling. This later defined a further 16 satellite porphyry targets in the Didipio region. Climax was been granted a Financial and Technical Assistance Agreement contract with the Philippine government. It allows 100% foreign ownership of mining projects. After four years of negotiations, Climax was the first company to have such an application granted. Some 120 applications from numerous international mining companies are waiting for approval following implementation of new Philippine Mining Act of 1995. Exploration history Didipio is located 200 km (125 miles) north of Manila at an elevation of about 700 m (2,300 ft) in the remote Sierra Madre mountains. This region remains mostly unexplored. The property is accessed by 25 km (15 miles) of logging track from the town of Cabarroguis, Quirino. The area experiences an average rainfall of about 3,000 mm (118 in.) a year. Most of it falls during the July-to-November typhoon season. Didipio was first recognized as a gold province in the 1970s when native Ifugao and Ilongot hunters discovered alluvial gold in the region. The region had been prospected over the years by local companies. They were mostly prospecting for alluvial gold. However, in 1988, Climax Mining geologists identified the potential of an obscure razorback ridge protruding from the alluvial valley floor. This ridge, later named Dinkidi by Climax, was the site of several small- scale tunnels. Locals had mined narrow quartz stockwork veining and sluiced soft argillic alteration zones, using irrigation canals and sluice boxes to catch free gold.

Jan 1, 1997

By R. E. Le Messurier

GENERAL DESCRIPTION The mines are located at Broken Hill in the western part of New South Wales, Australia, 930 km west¬northwest of Sydney. Mining Methods Where pillars must be left between stopes, extraction of a block of ore between two or more levels is carried out in stages: 1) Stopes are mined overhand by horizontal cut¬and-fill stoping, or by long-hole stoping. The various methods of horizontal cut-and-fill stoping used are desig¬nated as: -Loader cut-and-fill stoping with horizontal blast¬holes and diesel load-haul-dump (LHD) units. -Open stoping with horizontal blastholes and com¬pressed air or electric scrapers, or with diesel or electric LHD units. Square-set timber stoping, where ground condition precludes open stoping. The backs are sup¬ported with timber square sets. Pattern rockbolting of the backs may be used as an intermediate stage between open stoping and square-set stoping. 2) Vertical pillars are mined by undercut-and-fill stoping or by vertical crater retreat stoping. 3) Where a horizontal pillar has been formed below the level above the primary stope, this level pillar, usually 6.1 to 8.2 m in depth, may be mined by over¬hand square-set stoping or by undercut-and-fill. Long-hole stoping is used at the Zinc Corp. (ZC) and New Broken Hill Consolidated (NBHC) to mine parts of the zinc-rich A and B lodes. Drilling is carried out from drill drives and, in some cases, sills. Hole sizes used are 165 mm (61/2 in.), 110 mm (4'h in.), and 65 mm (21/2 in.) nominal diam with hole lengths being limited to 50, 30, and 20 m respectively. Ammonium nitrate-fuel oil (ANFO) and water gel explosives are used. Broken ore is loaded from drawpoints at the bottom of the stope using rubber-tired diesel-driven LHD units which deliver ore to an orepass. Annual production at Zinc Corp. and NBHC accord¬ing to mining method is given in Table 1. At Zinc Corp. mining is being carried out at depths varying between 200 and 832 m. At NBHC it ranges from 528 to 915 m below the surface. The average travel time to the stope is 30 to 45 min. GENERAL ORE BODY REQUIREMENTS Size, Shape, and Dip There are six separate lodes which carry minable ore in the mines of Zinc Corp. and New Broken Hill Consolidated. The lowest of these and the main ore bodies presently being mined at Zinc Corp. are the lead lodes, consisting of a siliceous fluoritic ore body (No. 3 lens) and overlying it a calcite rhodonitic ore body (No. 2 lens). Each possesses characteristic ratios of lead, silver, and zinc, although the grade within each lens is variable, in places being as high as 30% Pb. There are also low¬grade portions which consist chiefly of poorly mineral¬ized rhodonitic material. No. 3 lens terminates within the Zinc Corp. leases, while No. 2 lens continues into the NBHC leases where it continues to provide a significant proportion of pro¬duction from the mine. Overlying the No. 2 lens are the various zinc-rich ore bodies. In ascending sequence these are lower No. 1 lens, upper No. 1 lens, A lode, and B lode. A typical assay for the small No. 1 lens group ore bodies is 8% lead, 50 g/t silver, and 20% zinc. The `A' lode is a large low-grade ore body in which the higher grade sections assay 4% lead, 30 g/t silver, and 10% zinc; larger quantities of lower grade ma¬terial also occur. B lode, the main zinc lode, typically assays 5% lead, 30 g/t silver, and 17% zinc. B lode increases in size as it extends south, and in NBHC is a major ore body, contributing about 52% of the production. All the lodes pitch south, the average pitch being 0.52 rad (30°) in the Zinc Corp. leases and rather flatter than this in the NBHC leases (see Figs. 1-3). The ground is all competent rock. Production requirements at Zinc Corp. are 900 000 t and 1 200 000 at NBHC.

Jan 1, 1982

By A. P. Schissler

2013 has seen metals, industrial minerals, and coal all reduce in price due to market and geo-political factors. Many companies are taking write-downs to recalibrate their reserves and have enacted focused cost reduction programs. The public domain includes statements where companies have operating cost reduction goals in the $500 million range. Zero-base staffing & budget analysis is a means to achieve optimal employment and cost levels for a given level of production. The method involves measuring the work to be done similar to Lean. Lean is a method to review each step of production and remove anything that doesn?t add value or is necessary to complete finished goods. Zero-base methodology has been applied to mines worldwide producing realistic and sustainable levels of staffing and costs based on the quantity of work. The objective of this paper is to provide the framework of zero-basing with examples of application.

Feb 23, 2014

By J. J. Renton

The iron disulphide minerals, pyrite and to a lesser extent marcasite, are ubiquitous to coal and coal associated rocks and are the source of nearly all the environmental problems associated with the mining, processing and utilization of coal. The iron disulphides as well as the other minerals in coal exhibit systematic spatial pat- terns of distribution on both regional and local scales and show predictable associations, most of which are determined by the geochemical-sedimentological controls under which they form. It is the purpose of this paper to discuss the geochemical-sedimentological conditions responsible for the formation of coal minerals with special emphasis on the formation of iron disulphides, to illustrate the regional and local patterns of mineral occurrence within coal, to present the microscopic associations of the iron disulphides and finally, to discuss the most important single environmental aspect of the iron disulphide content of coal and coal associated rocks; the production of acid mine drainage.

Jan 1, 1986

By M. Akser

Ilmenite, rutile, and zircon deposits of commercial importance have not been reported to-date from Turkey. However, information from recent reconnaissance activities indicates the possibility of an economically viable heavy-mineral deposit along the Black Sea coast of Turkey in the vicinity of Ormanli, northwest of Istanbul. Consequently beach and sand dune samples were collected from that area for additional analysis. Laboratory methodologies, designed to simulate standard industrial heavy-mineral plant practices, were used to analyze and evaluate the samples. Based on the analyses, and current market needs, none of the deposits in the Ormanli area qualify as a commercial heavy-mineral deposit.

Jan 1, 1995

By William A. Rehrig

During recent years, there have been frequent investigations on the geochemistry of biotite. This work has emphasized, and no doubt was prompted by, factors related to mineral exploration, particularly for those deposits of the porphyry copper type. A large number of papers have been devoted to the obtainment of trace-element data from plutonic biotite. These data have been used to extract primary geochemical information pertaining to the parent magna and the hydro-thermal system which together give rise to porphyry copper deposits. In two early works, Putman and Burnham (1963) and Parry and Nackowski (1963) analyzed base metal contents of ferromagnesium minerals, primarily biotite, from various barrenfmineralized plutons of the Basin and Range Province. One similar conclusion from the two studies was that the Cu, Zn, and Pb contents of magmatic biotite served as indicators of ore development within the granitic rocks genetically related to ore. This theme was then pursued vigorously by a number of authors until the present time. Results, however, have been contradictory, as reviewed by Coope (1974). For example, studies by A1 Hashimi and Brownlow (1970), Lovering et a1 (1970), Putman (1972), and Graybeal (1973) continued to support positive primary relationships between the trace-metal content (usually copper) of biotite and associated sulfide mineralization. By studying biotite in close spatial association will sulfide occurrences, Putman (1972) and Graybeal (1973) developed models for base metal partitioning in magmatic systems based on their discovery of inversely distributed copper between silicate (biotite) and sulfide phases. Conversely, research by Bradshaw (1967) and Blaxland (1971) plus the recent findings of Parry and Jacobs (1975) and Kesler et a1 (1975) found little if any evidence to support a correlation of biotite base-metal or

Jan 1, 1976

By S. Vivek

An atomic force microscope (AFM) was used to measure the surface forces between silica plate and glass sphere in sodium oleate solutions. Hydrophobic forces were observed when the two surfaces were activated by CaOH+ or MgOH+ ions. The force measurements conducted in the absence of the surfactant showed that the activated silica surfaces do not exhibit the primary hydration forces that have been observed between unactivated surfaces. The activation mechanism was studied by calculating the contributions from electrostatic and chemical interactions to the total free energy change. The results suggest that the adsorption of the hydroxo-complexes is controlled mainly by the lateral interactions between the adsorbed species on the silica surface.

Jan 1, 1999

By A. Aly Selirn

An economic simulation model was developed to predict the amount of copper recovered from copper oxide deposits and the cost of producing it as a function of the deposit parameters. The economic simulation model includes models of fragmentation design and cost, copper extraction, solution distribution and recovery, effluent solution cutoff grade, and financial analysis. Cost and price indices were also developed to evaluate the economic feasibility of in situ leaching operations as a function of their starting date. Application of the models to various properties having the same area and different ore thickness shows that the effluent solution cutoff grade does not vary with the ore thickness nor with its grade. The percent of copper recovery is, however, shown to increase with the increase in the ore thickness and is independent of the ore grade. it is also shown that while the profit per unit of extracted copper increases with the increase in ore grade or ore thickness, the rate of return on total investment does not show any correlation

Jan 1, 1977

By R. K. Clifford

The formation of elemental sulfur on the surface of sphalerite in aqueous systems was investigated. Hallimond tube flotation tests showed that unoxidized sphalerite did not float well without a collector. Flotation recoveries of greater than 95 percent were obtained without the use of a collector or frother after the sphalerite had been reacted with oxygen under pressure and water at pH 2.8 at room temperature. High flotation recoveries also resulted when sphalerite was reacted in acidic solutions in the presence of platinum sponge, titanium sponge, 316 stainless steel, copper turnings, or [10-5M++]. Conditions which produced high flotation recoveries of sphalerite yielded contact angles of 37° to 40° and also produced elemental sulfur. The increase in elemental sulfur on the surface of sphalerite was detected by elemental sulfur extraction with petroleum ether, electron spectroscopy for chemical analysis (ESCA), and the electron beam microprobe. The quantity of elemental sulfur formed was insufficient to be detected by infrared or Raman spectroscopy, or by the optical microscope or by the scanning electron microscope. An electrochemical type reaction for the production of elemental sulfur in acidic solutions was proposed. The cathodic reduction of oxygen was the slow step which needed to be catalyzed. A chemical type reaction which produced H2S rather than elemental sulfur was evident in non-oxidizing conditions.

Jan 1, 1974

The nature of adsorbed calcium carboxylates (oleate and stearate) has been investigated by in-situ/ex-situ Fourier transform infrared internal reflection spectroscopy (FTIR/IRS). Previous spectroscopic studies in alkaline solution have shown that adsorbed carboxylate is characterized by a C-O stretching vibration at about 1550 em?1 for less than monolayer coverage. Similar results were found in this study. More specifically, in this study such a singlet at 1550 cm-1 was found for LB monolayers of calcium distearate transferred as a condensed layer at a high film pressure to the surfaces of fluorite and germanium. Normally the spectrum of bulk calcium distearate reveals a doublet at 1575 and 1540 cm-1, characteristic of a three dimensional 7-fold coordination for calcium carboxylate complexes. This doublet is generally found for carboxylate multilayers formed by spontaneous adsorption at the surface of calcium minerals. In this regard, the spectral evidence suggests that whenever the calcium dicarboxylate is constrained at a surface as a condensed layer, the 7-fold coordination can not be satisfied and the surface carboxylate is forced into a two dimensional symmetrical coordination with a singlet at 1550 cm-1. On the other hand, if the Langmuir-Blodgett (LB) monolayer calcium distearate film is transferred at a low film pressure the doublet is observed. This analysis is further confirmed by the spectral results for LB transferred calcium distearate monolayers at a hydrophobic silicon surface. Even though these are condensed monolayers formed at high film pressure, the carboxylate group, oriented away from the surface, is no longer constrained by the surface force field, and thus exhibits the characteristic doublet of the bulk calcium distearate salt.

Jan 1, 1998

By Mark Colwell

This paper summarizes the results of a research project whose goal was to provide the Australian coal industry with a longwall installation roadway (faceroad) design methodology that could be utilized by suitably qualified colliery personnel. This goal was achieved in 2012 and the design methodology (and software package) is referred to as Analysis and Design of Faceroad Roof Support (ADFRS). The intended benefits to underground operations, in the provision of this information and resource, are a safer and more productive workplace.

By Ezz El Din Abdel Hakim Khalaf, Khalid S. Essa, Marc Munschy, Mohamed A. S. Youssef

This study focused on joint interpretation of the aeromagnetic and radiometric data to allocate and describe the structural elements and mineralization zones such as uranium, gold, and sulfide in the Gebel Umm Tineidba and its surroundings, Eastern Desert, Egypt. The study region is covered by exposures of Precambrian rocks such as gneisses, migmatites, ophiolitic mélange, metavolcanics, younger granites, and Quaternary sedimentary covers. The application of the total intensity magnetic and reduced-to-pole maps, power spectrum, analytic signal, tilt-angle, and local wavenumber maps helps in recognizing magnetic sources distribution, lineament features, and mineral zones delineation. The obtained results indicate that the depths of the deeper NE–SW, NNE–SSW, and N–S trending structures extend from 400 to 1750 m and shallower ones range from 100 to 400 m. Finally, the main trends of these structures affect the probable mineralization zones.

Sep 22, 2022