Search Documents

By Zhenqi Cai

The ongoing Overpeck Valley Parallel Sewer Project of Bergen County Utilities Authority (BCUA), New Jersey, is a US $65 million CSO improvement program to meet a State DEP consent order by 2010. One major program component includes a total of 1.8 km (1.2 mile) long, 1,800 mm (72 in) diameter reinforced concrete pipe (RCP) installed by a Herrenknecht AVND1800AB MTBM. The alignment includes drives through 850 m (2,788 ft) of extremely soft glaciolacustrine varved clay, 980 m (3,214 ft) of loose to medium dense mixed soils containing silty sands, gravels, and boulders, and crosses under the New Jersey Turnpike, US Highway Route 46, and a CSX Railroad Intermodal Yard and a branch mainline. Two types of MTBM cutterheads are being used, one configured for the weak varved clay, and one for the mixed soil conditions. The MTBM is also equipped with a double-steering system consisting of a standard front steering joint and a second trailing steering joint to assist grade control should adequate steering not be achieved by the front primary steering in extremely weak soil conditions. This paper discusses the significant engineering aspects and challenges related to site settings, ground characterization, key MTBM features and performance, and required ground treatment.

By Fred Breu, Ronald E. Heuer

INTRODUCTION The Point Lepreau nuclear generating station was constructed in the late 1970's and early 1980's by the New Brunswick Electric Power Commission. Point Lepreau is a small peninsula on the north shore of the Bay of Fundy, about 55 km west of St. John, New Brunswick. Cooling water for the plant was to be obtained from and discharged into the Bay of Fundy by the system of shafts and tunnels illustrated in Fig. 1. The design engineer for the cooling water system was Albery, Pullerits, Dickson and Associates, Ltd., Toronto. Ferrera-Resco Ltd, Windsor, Ontario, was contractor for construction of the cooling water shaft and tunnel system, which was done between 1976 and 1979. The senior author was project manager for Ferrera-Resco, the junior author served as consultant to Ferrera-Resco on evaluation of certain geotechnical questions which arose during construction. SITE CONDITIONS Geology Except for limited overburden soils at the onshore shaft sites, the tunnels and shafts were constructed entirely in Triassic conglomerate, sandstone, and siltstone, with some shale interbeds. The bedding strike averaged about N6°E, The dip was to the west at about 30° along the Discharge Tunnel and 40° along the Intake Tunnel. Rock along the Intake Tunnel was mostly sandstone and siltstone and more thinly bedded, with RQ D generally in the range of 50 to 60%. Rock along the Discharge Tunnel tended to be coarser sandstone and conglomerate and more thickly bedded, with higher RQ D averaging about 80%. In addition to bedding joints, two other joint systems were identified

Jan 1, 1985

By Edward J. Cording, William H. Hansmire

INTRODUCTION The Washington Metro, a rapid transit system that will serve the District of Columbia, Virginia, and Maryland, has been under construction for about two years. Construction of the Metro by the Washington Metropolitan Area Transit Authority involves a large amount of cut and cover, soil tunnel, and rock tunnel construction. To aid initial construction and improve future designs, performance observations were undertaken on tunnels in the initial construction phase. The University of Illinois Department of Civil Engineering was engaged to carry out a comprehensive program of field observations and measurements for this purpose. One part of the program was on the first soft ground tunnel constructed in the system. The tunnel is a 2200-ft (670 m) twin-bore section, designated Contract A-2, in downtown Washington. Two objectives of this program were to determine the relationship of construction procedure to settlements and to observe the pattern of soil movement around the tunnel as an aid in evaluating underpinning criteria for nearby structures. A test section, consisting t three instrument lines located across the tunnel path, was established prior to mining in Lafayette Park to measure in detail both vertical and lateral soil displacements as the tunnel was mined through the section. The site was selected because it is free from surface structures and access for installation and reading of the instruments was convenient. Load and distortion measurements on the lining were also made within the test section; observations of construction procedure were maintained throughout construction.

Jan 1, 1997

By A. J. Kwitowski

Remote control is usually associated with deep mine, continuous mining machines. This is because thin-seam operation precludes an onboard operator's compartment or the mine has approval to conduct extended cut mining. Using a tethered or radio-linked control box, the remote operator is typically situated 3 to 15 m (10 to 50 ft) from the working face. The operator receives direct operational cues through senses like vision, hearing and feel. Remote control is sometimes touted as a safety feature. However, this is not always true, as operators are not provided protection from roof and rib falls or being crushed between the machine and a rib. Remote control operators are also left exposed to dust and noise. Teleoperation described here is the computer-based, distant control of mining machinery from a protected operator compartment located out of the line-of-sight from the operational site. Video, sound and other sensory information are gathered through sensors and electronically transmitted to and displayed at the operator's location. The teleoperator responds to the information and makes decisions that are initiated by control devices (usually switches). These control commands are then electronically transmitted to the re¬mote machinery and the appropriate machine function(s) are carried out. Teleoperation increases the safety of mining machine operators as it removes them from the immediate vicinity of hazards. The US Bureau of Mines' involvement with teleoperation dates back to 1979. Following feasibility studies, a highwall milling system (HMS) was developed and tested. A deep, thin-seam, room-and-pillar system (TSRPS) has been designed and is currently being surface tested.

Jan 1, 1992

By Y. C. Kim, I. S. Roditis, P. K. Medhi

P. Mousset-Jones I found the article most interesting and timely. I consider it imperative that mine case studies like this one are undertaken and published so that the practicing mining engineer and geologist can obtain a better idea of what is the preferred estimation and grade control technique to use, given the site-specific geology, grade distribution, etc. Mining companies, with operating gold mines, need to be encouraged to either initiate such a study in-house or support a research project by financing a graduate student at a local university. The latter method is preferable since it not only provides research support but also an excellent training opportunity for young mining engineers and geologists. Ideally, what is needed is exploration drill-hole, blasthole, and mine production data that can then be used to assess the efficiency of different estimation and grade control methods by comparing the results obtained using the drill/blasthole data with the actual production data. It is hoped that more mining companies will realize that the rewards from this kind of research greatly outweigh the sometimes perceived problem with releasing data to a university. I noticed that the authors used the blasthole data to represent the actual values, the validity of which relies heavily on the two key assumptions with regards to blasthole assays and in-pit ore-waste selection procedures. Could the authors comment in more detail on these assumptions and what criteria they used to check the validity of the assumptions? Since the article was published, have the authors had the opportunity to compare their estimates with the actual production data? It would be interesting to compare other estimation methods with OK and IK. For example, how well did the polygonal method used at the mine compare with the results given in the paper? I would like to mention that B.L. Kwa completed a similar study (Kwa and Mousset-Jones, 1986) using exploration drill-hole, blasthole, and production data from the Alligator Ridge mine in Nevada. The study compared a variety of estimation methods, including IK, and the final results are shown in Fig. 1. The IK method exhibits the smallest difference between estimated and production results and is closely followed by the indicator moving window (Ind MW) method. Reference Kwa, B.L., and Mousset-Jones, P., 1986, "Indicator Kriging Applied to a Gold Deposit in Nevada," Proceedings, Symposium on Ore Reserve Estimation Methods, Models, and Reality, CIMM Annual Meeting, Montreal, Quebec, Canada, May, pp. 185194. Reply by Y.C. Kim We do concur with Professor Mousset-Jones with respect to the merit of such case studies performed at a local university. In answer to his request for comment on the validity of the two key assumptions made in our paper, we can only say that these are reasonable assumptions that are very difficult to validate. The assumption of blasthole assays being accurate can be partially validated by a careful analysis of the nugget component of blasthole variograms. The assumption that the in-pit ore-waste selection procedure in use was an effective one can only be validated through comparison between the mine estimates of ounces of gold versus the actual recovered ounces of gold at the mill. Neither one of these two assumptions has been validated to date due to several reasons. For example, the mine went through a change in management since the study. Similarly, no compelling reasons have been presented to perform detailed variogram analysis of the blasthole data. We do, however, believe that the obtained results (i.e., indicator kriging performs better than OK in a highly skewed deposit) will remain the same in relative terms, regardless of how valid these two assumptions may be. The most recent comparative study by D. S. Lindsey of the Montana College of Mineral Science and Technology also shows a similar ranking between ordinary kriging versus probability kriging, which is an extended version of indicator kriging. Reference Lindsey, D.S., 1987, "A Comparative Study: Probability Kriging vs. Ordinary Kriging at the Golden Sunlight Mine," MS Thesis, Department of Mining Engineering, Montana College of Mineral Science and Technology, Butte, MT, May, 81 pp.

Jan 3, 1988

By Kirsten Corin, Belinda McFadzean, Cyril O’Connor, Jenny Wiese

The Bushveld Complex of South Africa contains almost 90% of the world’s reserves of platinum group minerals (PGMs). In the flotation of PGMs, there are significant challenges arising from the need to treat ever-decreasing grades of the relevant ore deposits. The major challenge in the flotation of these ore bodies is the control and management of the gangue minerals, particularly silicates such as orthopyroxene, plagioclase feldspar, and pyroxene which are often rimmed with talc which makes them naturally floatable. It has been shown that various polysaccharide depressants such as CMC and guar have different properties in terms of depressing the gangue minerals. Since the PGMs are often associated with sulphides, copper sulphate is widely used as an activator in PGM flotation but can inadvertently activate the gangue minerals as well as reduce the recovery of PtTe2 which accounts for up to 40% of the Pt in the Platreef ore body. Depressants also reduce the mass of solids reporting to the froth and can thus destabilise the froth. This effect on the froth can be mitigated by using higher frother dosages or water of higher ionic strength. Reducing chromite recovery is of critical importance since high levels may negatively affect the downstream smelting process. Chromite recoveries can however be reduced through the application of gravity separation or reducing entrainment through reduced water recovery. In summary, due care needs to be taken to carry out site test work to develop an optimum ratio of collector, frother, activator, and depressant to ensure that the highest grades and recoveries of the PGEs are obtained while reducing depressant dosage as much as possible.

Underground mine designs typically try to avoid extraction beneath streams and rivers of any significant size, especially when the overburden rock thickness between the stream bed and the mine is thin. Potential issues with mining beneath streams include excessive groundwater inflow to the mine; weak ground (roof, floor, and pillar) conditions; horizontal stress effects; as well as stream loss and other potential adverse environmental effects. However, there are times when crossing beneath a stream or river is necessary to move into a new area of mineral reserve without creating additional mine access points from the ground surface. Often, stream crossings are completed without thorough assessment, potentially resulting in increased costs, decreased safety, and, in some cases, failure to advance the mine. Selection of the most favorable location(s) to cross the stream must account for numerous factors and the associated assessment often requires a multidisciplinary approach. Stream crossing investigations often require geological, hydrogeological, geotechnical, and geophysical expertise. Phases of stream crossing investigations include desktop evaluation of maps and aerial photography, stream bed observations, drilling, detailed rock core logging, downhole geophysical surveying, hydraulic conductivity testing (packer testing), geotechnical laboratory testing, assessment, and reporting. The deliverables from a stream crossing assessment typically include geological, geotechnical, and hydrogeological characterization of potential stream crossing locations; classification of favorable and unfavorable crossing locations; recommendations for entry design and pillar sizing; and recommendations for if, and how, to conduct pre-grouting activities. Examples of technical aspects of data collection and assessment are provided based on decades of industry experience conducting stream crossing assessments in various underground mining scenarios.

Jul 28, 2020

By Andres Salazar, Carlos Delgado Robles, Richard K. Preece

Minera Escondida, located in the Antofagasta Region of northern Chile, is the world’s largest producer of copper as concentrate and SX-EW cathode. Projects to increase mill and flotation capacity began soon after start-up in 1990 to off-set decreasing copper grade. Subsequent projects had the objective to increase copper production through heap leach and SX-EW production and a second concentrator. The mine footprint concurrently expanded peripherally from the central high-grade enriched core of Escondida and then into the separate Escondida Norte deposit. Early in the mine life, metallurgical forecasting that was based on metallurgical composites of presumed ore types and historical plant production was adequate for operational planning, plant design, and project valuation. This approach became unreliable, however, as the increase in mine footprint was accompanied by an increased variability in key ore body characteristics such as hardness, copper-iron sulfide mineralogy, and sulfide liberation textures that were not reflected in the geological criteria used for ore type designation. The project study teams turned to small-scale physical and chemical tests to better characterize the spatial distribution of these key ore characteristics. Programs associated with capital growth projects were carried out through the mid-2000s to sample and construct a three-dimensional spatial model of hardness, copper sulfide mineralogy, and rougher flotation recovery from tests on 15-m drill core composites. Mathematical models were developed from the respective ore characteristic data to calculate throughput, flotation recovery, and concentrate copper grade. The spatial models were integrated with the concurrent mineral resource block model using standard geostatistical methods and the metallurgical process calculations were applied to the block estimates. The geometallurgical model, originally constructed on a project basis, is now managed by a dedicated team reporting to the manager of Geosciences & Resources Definition in the Escondida organization. The model has evolved with increasing complexity of the mine and processing plants and currently includes seven forecasting areas for three concentrators and four areas for two leach plants. Metallurgical forecasts of mill throughput, final flotation recovery, and concentrate copper grade still have the highest relevance to mine planning and optimization. Sample preparation, test procedures, and quality control methods are summarized for the ore characteristic tests important to these forecasts. Analytical results from recent annual sampling programs are presented for the hardness indices, rougher flotation recovery, and partial extraction copper analyses. Geostatistical analysis of the SAG mill hardness index is summarized as an example for the spatial estimation process. Mathematic models are presented for throughput (based on hardness indices), final flotation recovery (based on rougher recovery and plant calibration studies), and concentrate copper grade (based on sulfide mineralogy and empirical pyrite rejection studies).

Aug 31, 2023

By Raquel Costa, Aldino Campos, Frederico Carvalho Dias, Pedro Madureira, Patrícia Conceição, Ana Filipa Marques, Andreia Afonso, Maria Ana Martins, António Calado, Luísa Pinto Ribeiro

Since its formation in 2004, the Task Group for the Extension of the Continental Shelf (EMEPC) has been collecting hydrographic, geological and geophysical data to support the extension of the continental shelf beyond 200 NM. In 2008, the EMEPC acquired a 6,000 m rated ROV named "Luso" and has been cooperating with several national and international institutions to increase and improve its operational capabilities to conduct research on deep-sea minerals. The Portuguese continental shelf corresponds to a broad area of the seafloor encompassing different physiographic domains: the mid-Atlantic ridge system, abyssal plains and numerous seamounts. From 2008 to the present, the mid- Atlantic ridge and seamounts have been the most visited sites with the ROV "Luso". Several hydrothermal vent sites are known to occur along the mid-Atlantic ridge to the south of the Azores archipelago and mostly within the Portuguese EEZ. Vent fields were also discovered in the extended continental shelf, namely the Rainbow and the Moytirra sites located to south and to the north of the Azores archipelago, respectively. The most studied seamounts correspond to those forming the Great Meteor chain and the Madeira- Tore rise. All these visited sites are related either with the occurrence of polymetallic sulphides or cobalt rich Fe-Mn crusts and the opportunities to further pursue their exploration will be discussed.

Sep 1, 2014

By J. Drew

Oregon Resources Corporation (ORC), an industrial minerals mining company, is currently engaged in the development of a new process design that will allow the unique paleo-beach placer deposits of southwestern Oregon to be mined efficiently and economically, creating an additional domestic source for chromite, garnet, and zircon. Engineering design has been guided by the variable geology and mineralogy of the paleo-beach placer deposits as well as the need for a dry tailing scheme that resolves a lack of water resources at the placer locations and at the same time eliminates the need for slurry settling ponds, typical of paleo-beach placer operations in North America. Metallurgical study of the placer material was grouped into four distinct samples based on marine terrace deposition, geological facies, and mineralogy. Because the metallurgical samples represented the extremes likely to be encountered in all future Oregon paleo-beach placer ores, the process design is highly dynamic and will successfully adjust to meet the production needs. Water availability at the mining area is seasonal and will not support a typical placer operation?s water requirement needs for heavy mineral concentration. For this reason, ORC has developed a plan to construct the ore processing facilities near Coos Bay, where a municipal source of water is available. Raw ore will be transported from the mining sites approximately twenty miles one way to the processing facility with return loads hauling tailings back to the active pit. The need to haul dry tailings, return dry material to the pit for reclamation, and limit the amount of water being purchased from the municipality has driven the design of a unique water reclamation system. BACKGROUND Location and Access Economic concentrations of ?black sand? or heavy mineral (minerals with specific gravity greater than 2.85) have been recognized and studied in marine placers from Coos Bay to the mouth of the Rogue River, a distance of approximately 75 miles along the southern Oregon coast (Hornor, 1918; Griggs, 1945)(Figure 1). ORC will begin mining existing reserves approximately 20 miles south of Coos Bay in a region known locally as Seven Devils. Ore will be trucked north to the processing site near Coos Bay via use of existing county and state roads, including U.S. 101. The available facilities at the processing site include highway, rail, municipal water and electricity, natural gas, and a deep water port. At the time of this writing, the rail line had been abandoned, but was being pursued by the International Port of Coos Bay. It is anticipated that this will be serviceable at some time in the future. History The southern Oregon marine placers have garnered the interests of miners since 1852, when present day beaches were exploited for gold. The beach deposits were small and irregular in nature and were easily washed away by the major storms the coast endures during the winter months (Hornor, 1918). [ ] In the 1920?s, deposits at the beach were followed upstream to their paleo-beach terrace origins (Pardee, 1934). These terrace placers were mined, but with little success, as the cost of mining and processing was greater than at the present day beach deposits. The greatest effort to understand and delineate the paleo-beach terrace placers came during World War II. As the need for a domestic source of steel hardening chromite was evident, the heavy mineral bearing placers of southwestern Oregon provided just that. The U.S. Geological Survey, under guidance from the Oregon Department of Geology and Mineral Industries, began exploration drilling of the paleo-beach terraces in 1940 (Griggs, 1945). This work was part of the investigation of strategic mineral deposits and would ultimately supply much needed chromite for the war efforts. The first mining efforts began in 1943 by the Humphreys Gold Corporation and the Krome Corporation (Griggs, 1945). Black sand

Jan 1, 2009

By G. Mike Bernard

The Andacollo gold mine is located near the town of Andacollo (population 14,000 people) in Chile’s region four. It is about 56km (35 miles) by paved road from the coastal city of La Serena. Santiago is about480 km (300 miles) south. Site elevation varies between 1,000 and 1,280 m(3,300 and 4,200 ft). The climate at the Andacollo site is moderate but arid. Average annual rainfall is only 130mm (5 in.). Because there is little rain and the temperature varies only a few degrees (14 to 24 C or 57 to 75F), there are no problems with freezing, solution dilution or pad saturation. The climatic conditions are ideal for heap leaching.

Jan 1, 1996

By B. J. Dave, Ashok J. Desai, Allen J. Hulshizer

This paper presents various design and construction considerations involved in developing an underwater installation of lined, large diameter shafts not known to have been previously accomplished for the diameter size, depth or ground conditions identified with the Seabrook Power Station. Outlined approach provides for driving tunnels independent of shaft sinking operation, permits the use of prefabricated shaft lining and incorporates a safe dry tap method for connecting the shafts to the tunnels. INTRODUCTION The Seabrook Power Station, located two miles inland from the Atlantic Ocean, at Seabrook, New Hampshire, is a two unit, nuclear powered, electric generating plant, each unit having a capacity of 1150 megawatts (electric). Typical to all steam driven generators is the requirement for large quantities of water. Requirements for the Seabrook Plant will be met by intaking and discharging approximately 850,000 gpm of ocean water at a considerable distance from the shore line in water depths that render the environmental impact inconsequential. Obtaining, conveying and discharging such large quantities of water represents a major undertaking, particularly under today's environmental controls. Tunnels are well suited to reducing the environmental impact at the Seabrook site by conveying the water about 250 feet deep under the salt marsh (a valuable ecological feature) and under the beach well out into the ocean without any noticeable ground surface disturbance. An alternate approach utilizing trenched piping would have created some disturbances and was environmentally less desirable. The tunnels connect to intake and discharge

Jan 1, 1976

By W. Pariseau, S. Puri, S. Schmelter

Introduction Joints often have profound effects on elastic properties and strength of rock masses and therefore on rock slope stability. In surface mine slopes, joints are usually too numerous to be taken into account individually, so an equivalent properties approach is necessary. Previous work that treats a jointed rock mass as an equivalent composite material of joints and intact rock between resulted in excellent agreement between estimated and true rock mass elastic moduli in case of fully persistent joints (e.g., Pariseau, 1999) Rock mass failure mechanisms on joints and through intact rock were retained obviating the need for an equivalent rock mass strength. Impersistent joints, which are not continuous on a joint plane, can be accommodated (Pariseau, 2003). However, slope stability analysis of a large, deep copper mine indicated a need for computational efficiency even in two-dimensional analysis of vertical sections through pit walls (Puri, 2006). The analyses by the popular finite element method used small elements of bench size near the pit slopes and much larger elements away from the pit walls. The reasons for the graded meshes were numerical quality (small elements) and computational economy (large elements). Small elements contained only a few joints, while the larger elements contained hundreds of joints and led to impractical computation run times (days!). A new modeling procedure that recognizes sufficiently large elements as representative volume elements (REV’s) overcomes this obstacle. A companion improvement recognizes the concept of a representative area element (RAE) in association with joint impersistence and the probability that joint material occupies a considered site. Both are steps towards greater model realism and a practical slope stability analysis procedure. Consider the open pit mine photo shown in Figure 1(a), a companion plan view in Figure 1(b), and the problem of slope stability where high slope angles favor economics but low slope angles favor safety. These competing factors in surface mining generally result in some sections of the mine that have unstable slopes that require monitoring and perhaps mitigating action to improve stability. Although stability of a given section may not be easy to quantify with a single number, useful design guidance can be obtained from a finite element analysis of a proposed mining sequence leading to future pit slopes and profiles. The presence of water from rain and snow melt indicates a need for a coupled analysis that links water pressure, effective stress and total stress (Schmelter, 2001).

Jan 1, 2007

By R. J. Lytle

INTRODUCTION Prior to excavation in soil and rock, it is useful to know the subsurface structure. This is important information both for safety and for equipment scheduling reasons. It is useful to know whether parts of the subsurface might be potentially troublesome or of different character than is generally thought present. By using geophysical probing, it is possible to infer the location and size of these unusual regions. The ground structure is commonly estimated from core samples taken from boreholes. These cores give a detailed knowledge of the structure in the borehole. However, knowledge of the structure exterior to the borehole can only be extrapolated from core data. By using seismic and electromagnetic cross-borehole geophysical probing, remote probing can be used to sense the region exterior to boreholes. A recent advance has significantly improved the state-of-the-art for defining the ground structure between boreholes. This new procedure utilizes large amounts of data and provides a detailed picture of the subsurface. The data processing algorithms used are similar to those in medical imaging of the human body using x-rays, a science called x-ray tomography. This imaging of the ground is called geotomography, which is a shortened acronym for geophysical tomography. Several examples of geotomography applied to imaging ground structure are presented. Our approach has been to probe the ground with electromagnetic and seismic waves. We map the region of interest with signals transmitted between multiple source and receiver pairs lowered in boreholes on opposite sides of the region (Figure 1). The received signals vary according to the transmission properties of the media

Jan 1, 1979

What is the preferred electrolytic cell design and why? Hall: Considerable research remains to be done on electrolytic cell design. Studies are presently being conducted to determine optimum voltage and amperage. Zadra cells, which were used in some of the first carbon plants, are efficient when properly installed. Gold and silver are deposited on large-capacity, cylindrical steel wool cathodes. At times high value sludge falls from the cathode to the bottom of the cell. Rectangular cells, which were developed at some smaller operations in Nevada, require less floor space and have some desirable features in that cathodes can be moved and sludge can be removed from cell bottoms without actually shutting down the circuit. In South Africa two types of cells using graphite and diaphragm configurations are being tested. Duncan: The rectangular cell has one problem it's easy for shortcircuiting to occur. If you don't have a good seal on the side of the tank and on the bottom, the solution is going to want to flow around the bottom and sides of the cathodes and you're going to get poor performance in the cell. That is the advantage the Zadra cell has over the rectangular cell. With good sealing, which is a must, you should be able to get a ratio of the value of the solution going in to the value of the solution coming out of 10 to 1. Ken, can you tell me what you're attaining on the Zadra? Hall: At the Homestake gold operation in Lead, the cathode in the No. 1 electrowinning cell is loaded to about 600 ounces when it is moved to the refinery. At this time the No. 2 cathode is moved to the No. 1 cell. The No. 3 cathode is moved to the No. 2 cell and a cathode with new steel wool is placed in the No. 3 cell. In rectangular cells this sometimes is not possible because the loading on the cathode in the last cell may be as high as that in the No. 1 cell. As Don has pointed out this can probably be prevented by good seal design between cathodes. Potter: At the risk of sounding as though I'm straddling the fence, I really believe that either the round cell, as developed by Jack Zadra, or the rectangular cell will do an acceptable job. The Zadra is a fine unit. Leaks are not unknown but there are not very many. However, the rectangular cell is very saving of floor space. Plastics have been greatly improved during the past year or two and there is a very efficient design for the rectangular cell. It would have six cathodes in it and contain about 25 ft of steel wool. The body of this rectangular cell would be reinforced fiberglass plastic but with an integral lining of a high temperature plastic. I think either cell is so efficient and reliable that I would almost be tempted to flip a coin depending on floor space requirements. Either cell can be used to pull a loaded cathode and to advance the lesser loaded cathodes. Don, what is the configuration of your cell? Duncan: The Pinson rectangular cell has dimensions 2 ft wide, 30 in deep, and 10 ft long-long enough to take a dozen cathodes and anodes. We are currently using six of each but are not up to full capacity as yet. It's a steel tank coated with rubber. We have copper bus bars, which brings to mind that the last cathode in the tank, in one instance, was loaded heavier than the first one. That was probably a function of poor contact between cathodes and the bus bar. You can have erosion of the bus bar and if you don't get current flowing into the anode and out of the cathode, the cells will not function properly. Kappes: Just a few comments on cell design. In an alcohol stripping circuit we are running in Beatty„ NV, we are using PVC pipes for all circuitry piping and a commercial polypropylene electrolytic cell. They seem to be working quite nicely. The cell itself has eight cathodes measuring 18 in2. At six gallons per minute flow into the cell, at an average gold content of about 500 ppm, we seem to get good loading on the first three to four cathodes and not much on the end cathodes. At 12 gallons a minute flow we seem to be seeing gold uniformly along all eight cathodes. We are running at quite a high amperage level, about 400 amps into that cell. Gene McClelland, US Bureau of Mines, Reno Research Center (from the floor): I was associated with a company where the packing density of their steel wool cathodes was much too high and created some short-circuiting problems in their electrowinning circuit. I would like to ask the panel if they can recommend a packing density for cathodes in pounds of steel wool per cubic foot. Hall: The weight of steel wool put on one of our cathodes is 10 lb and the dimensions of the cathode are such that density would be about 0.75 lb/ft3. Duncan: I made a rough calculation and I'm estimating about 2 lb/ft3. Potter: In checking over a number of electrowinning operations, I found apparently very satisfactory operation within the limits that have been mentioned. I have come to a figure of about 0.5-1.0 lb of medium grade steel wool per cubic foot packed as uniformly as possible, of course. One consideration in packing is the fact that there should be good contact between the steel wool and the conductor. Operators tend to compact the steel wool more than would be desirable just to try to maintain good contact.

Jan 10, 1981

By T. A. Rundle, K. Kim, W. M. McCabe, E. C. Gregory

Overcoring tests were conducted at the Near-Surface Test Facility(NSTF) to assess the suitability of five techniques (U.S. Bureau of Mines borehole deformation gauge (BDG), Commonwealth Scientific and Industrial Research Organization (CSIRO) hollow inclusion stress cell, Luleå triaxial gauge (LuH gauge), and Council for Scientific and Industrial Research (CSIR) doorstopper) for in situ stress determination in a closely jointed basalt. This effort is in support of the Basalt Waste Isolation Project, which is studying the feasibility of locating a nuclear waste repository in the basalts of the Hanford Site in southeastern Washington. This paper presents the results from the overcoring study that formed the basis for selection of two techniques to be used during the further exploration of the basalt formations at depth.

Jan 1, 1983

By W. G. Willson, Y. L. Li, P. D. Rao, D. E. Walsh

The combination of high moisture and low heating value has restricted most low-rank coal (LRC) usage worldwide to mine-mouth power generation. The objective of this study was to subject two Alaska low-rank coals to hydrothermal drying to enhance their marketability in the Pacific Rim markets and to evaluate the chemical and physical properties of the dried products as a function of process conditions. Coals from Usibelli Coal Mine and the Beluga coalfield have a heating value of approximately 18.5 MJ/kg and contain about 28% moisture. Hydrothermal treatment (at 275° to 325° C) of lump coal, from the Usibelli Coal Mine and the Beluga coalfield, enhanced the heating value of the material, on an equilibrium moisture basis, from 18.5 MJ/kg to nearly 27.8 MJ/kg. The product coal, with a high heating value and only 0.2% S, is an environmentally-acceptable premium fuel; additionally, with the Hardgrove grindability index of the coal greatly improved, its value is even further enhanced. An increase in hydrothermal drying temperature promotes vesiculation of resinite. Also, ulminite reflectance increased to 0.92%, and ulminite was subjected to widespread vesiculation; this resulted in a coke-like structure indicative that the material went through the fluid stage.

Jan 1, 1993

By K. Burke, G. Zhan, A. Mayer

A cover with capillary barrier effects (CCBE) is being constructed on the AA Leach Pad at the Barrick Goldstrike Mine site near Carlin, Nevada. The purpose of the cover is to eliminate/minimize infiltration of meteoric waters into the leach pad. Laboratory and numerical analyses indicate that Carlin Formation siltstone (TCS), a locally available material, has the necessary hydrologic characteristics when placed on the leach pad to act as a CCBE. A pilot study has been conducted on a small-scale test cover placed on the AA Leach Pad to examine the cover performance under irrigated conditions. The preliminary test results demonstrate that the designed cover is capable of preventing meteoric water infiltration.

Jan 1, 2001

By Rao Balusu, Bharath Belle, Krishna Tanguturi

A collaborative research project is undertaken by Anglo American Coal and CSIRO to develop appropriate strategies for gas and spontaneous combustion management of longer panels. Extensive computational fluid dynamics (CFD) modelling studies have been conducted and calibrated using operational longwall goaf gas data to obtain a fundamental understanding of goaf gas flow patterns in longwall panels of 1.0-km and 3.0-km lengths and a detailed investigation of the effect of various mining and operational parameters on goaf gas flow patterns. The modelling studies have also been used to investigate the performance of various gas drainage and proactive inertisation strategies during various stages of longwall panel extraction. Simulation results indicated that apart from tailgate (TG) side goaf holes, gas drainage from maingate (MG) goaf holes and the mid panel start-up goaf holes would be useful for flat seam field conditions. Operation of 8–10 goaf holes is recommended for field site conditions with high goaf gas emissions of 6000 L/s. The modelling results indicated that the traditional inert gas flow rate of 500 L/s currently used in some mines would be insufficient to achieve effective goaf inertisation in long panels. Results indicate that 3.0- km-long panels would require 1500 L/s of inert gas and there is a need for multi-point inert gas injection strategy for effective goaf inertisation. In this paper, details and results of modelling investigations and recommended strategies for gas and spontaneous combustion management in 1.0-km- and 3.0-km-long panels are presented.

By Rao Balusu, Bharath Belle, Krishna Tanguturi

A collaborative research project is undertaken by Anglo American Coal and CSIRO to develop appropriate strategies for gas and spontaneous combustion management of longer panels. Extensive computational fluid dynamics (CFD) modelling studies have been conducted and calibrated using operational longwall goaf gas data to obtain a fundamental understanding of goaf gas flow patterns in longwall panels of 1.0-km and 3.0-km lengths and a detailed investigation of the effect of various mining and operational parameters on goaf gas flow patterns. The modelling studies have also been used to investigate the performance of various gas drainage and proactive inertisation strategies during various stages of longwall panel extraction. Simulation results indicated that apart from tailgate (TG) side goaf holes, gas drainage from maingate (MG) goaf holes and the mid panel start-up goaf holes would be useful for flat seam field conditions. Operation of 8–10 goaf holes is recommended for field site conditions with high goaf gas emissions of 6000 L/s. The modelling results indicated that the traditional inert gas flow rate of 500 L/s currently used in some mines would be insufficient to achieve effective goaf inertisation in long panels. Results indicate that 3.0- km-long panels would require 1500 L/s of inert gas and there is a need for multi-point inert gas injection strategy for effective goaf inertisation. In this paper, details and results of modelling investigations and recommended strategies for gas and spontaneous combustion management in 1.0-km- and 3.0-km-long panels are presented.