Search Documents

By R. K. Jade

Although several studies in combining and bifurcating flows in two-way junctions and splits are reported, deviations persist in the estimated shock loss coefficients (SLCs). Due to their complex nature, more work has to be done to be able to correctly predict flow losses at these locations. In two-way splits, the flow at bifurcation is known to be characterized mainly by two recirculating zones in the downstream branches, whereas, in a junction one recirculating zone is observed immediately downstream of the main branch. The relative flow rate in the branches (quantity ratios) is treated as the only parameter defining the losses at these locations. However, the effect of wall roughness, if any, on SLCs becomes important for mine ventilation. This paper presents the critical determinants of shock losses at splits and junctions at varying quantity ratios. The flow at 90º split and junction was examined both experimentally and numerically for Reynolds number in the range of 1.0×104 to 1.6×105. With a well designed laboratory setup, using precision instruments, velocity and pressure measurements were carried out, by using two scales of wall roughness. 3D numerical simulations for these experiments were conducted by using ANSYS CFX modeling tool. CFD simulations yielded results that are reasonably close to experiments, providing high degree of satisfaction in numerically predicting losses across the splits and junctions. However, comparisons of these numerical simulation results with existing literature standards showed significant under-estimation of shock losses by the standard literature by as much as 50%. A clear rise in the magnitude of shock losses was noted in both the approaches, with increased wall roughness. Based on the current studies, predictor equations incorporating quantity ratios are developed for accurate estimation of shock losses. Further investigations on roughness are needed, before one is able to incorporate wall roughness into the prediction of SLC.

Jan 1, 2009

By Yngve Jordal, Sverker Hartwig

The IVAR Project is Norway's largest sewer project presently under construction. One part of it is an 8.1 km (26 575 ft) long, 3.5 m (11 ft 6 in.) diam tunnel, bored in one year. The tunneling project has been running smoothly; however, not everything has been easy. A few of its features are highlighted in this paper: The use of 9 0 (12 cu yd) muck cars on a double track back-up in such a comparatively narrow tunnel. Employing only four men in the tunnel, including the loco driver. A quartzite dyke - 96% quartz with 350 MPa (50 000 psi) and more compressive strength - turned out to be 640 m (2 100 ft) thick instead of the predicted 90 m (300 ft). Passing under a gaseous swamp with only same 5 m (16 ft 5 in.) of rock cover on top.

Jan 1, 1991

By Steve Kral

In 2002, many in the mining industry — companies, academia and government — realized that the industry would soon be facing a serious shortfall in salaried and hourly employees. Depending on whose numbers are to be believed, 20 percent to 50 percent of current mining professionals are expected to retire within five to 10 years. And there are not enough students currently enrolled in mineral-related programs to the fill the need. Part of the impending shortage in professionals was brought on by the industry’s negative image, which discouraged students from enrolling in mining engineering programs. Another part was that the industry was in the doldrums and was seen by the public as a dying industry.

Jan 1, 2006

By Wern-ping Chen

Technical and non-technical challenges exist in each mega infrastructure project. It?s no exception to the first US underground PPP Port of Miami Tunnel (POMT) project in Miami, FL. The POMT will connect two man-made islands, the Dodge and the Watson Islands, under the Biscayne Bay within highly porous limestone formation. Permeability as high as 0.1 cm/sec has been identified. Its 41-ft outside diameter, if constructed, is the largest precast segment lining in the US. Besides its geological and hydro geological challenges and risks, local community influence and impacts have controlled the fate of this project. This paper describes its tender design enhancements and the evolving of its slow advancement in resolving local community issues.

By Kent von Maubeuge, Charles R. Landis

The global bentonite industry is a dynamic market balancing a range of end uses with an ever growing number of bentonite producers. In addition, markets in developed countries are elevating the level of detail and transparency for materials reporting in programs, such as the Registration, Evaluation, Authorization and restrictions of Chemicals (REACH) program in the European Union. Bentonite is impacted by programs of this nature. The majority of the bentonite products sold around the world are sodium bentonites. These sodium bentonites consist either of natural sodium bentonites, or naturally occurring bentonite dominated by divalent interlayer cations (Ca+2 andMg+2) subsequently exchanged with sodium cation. The latter variety is often called “sodium-activated“, or “soda-ash treated” bentonite. Once exchanged with sodium, these bentonites are often difficult to distinguish from natural sodium bentonites using common commercial testing protocols. Due to their similar colloidal and bulk chemical properties; the lack of test procedures designed specifically to identify this product feature; and the failure to completely or effectively explain their differences, sodium-activated bentonite is often considered to be identical to natural sodium bentonite in the industry. This article defines both general types of sodium bentonite and presents a technique that could serve the industry as a tool to confirm the variety of sodium bentonite in question. Specifically, geochemical properties such as carbon (C13/C12) and oxygen (O18/O16) isotopic ratios can distinguish activated, even slightly activated bentonites, from bentonites not introduced to additional sodium during manufacture.

Jan 1, 2004

By A. K. Majumder

Particle motion in fluids is a subject of considerable practical importance to engineers working in fields such as hydraulics, river mechanics, chemical engineering and mineral processing. Many mathematical models have been proposed to predict the terminal settling velocities of particles in a fluid medium. The selection of an appropriate mathematical model has, therefore, become a challenging task for practicing engineers. This paper reports on an attempt to identify some of the useful models found in the literature for predicting particle-settling velocities in a fluid under free- and hindered-settling conditions. From this study, it was concluded that there is no well-accepted model validated by experimental data available for predicting particle hindered-settling velocities in a suspension of polydisperse and polydens particles. Collective efforts should, therefore, be made towards developing a hindered-settling model, as this is an absolute prerequisite for many model structures in mineral processing and other engineering disciplines.

Jan 1, 2007

By J. Pesl, R. Hurman Eric

Metal-slag phase compositions of molten iron and ilmenite smelting slags or solid titanate phases were determined between 1500° and 1700°C. The influence of oxygen partial pressure and impurity oxide additions including Al2O3, Cr2O3, MgO and SiO2 were investigated along with amount of reductant-carbon. The XRD revealed that the quenched slag crystallized as pseudobrookite (M3O5) solid solution in equilibrium with iron. Silica additions formed separate silicate phases because of its immiscibility in the titanate phase. Under strong reducing conditions iron oxide was almost completely reduced and the slag phase solidified as a consequence thereof. Cr2O3. SiO2 and MnO were also reduced to a high degree. Under weak reducing conditions the slag was fully molten and non of the impurity oxides were reduced. A significant portion of manganese, some magnesia and silicon, in the form of SiO gas, were removed via the gas phase due to their considerable vapour pressures. Alumina was not reduced under the applied conditions. A comparison of the experimental results with industrial data clearly suggested that industrial ilmenite smelting process operated under non-equilibrium conditions.

Jan 1, 2005

Basic parameters affecting the stability of foams have been studied. We used the thin film pressure balance (TFPB) technique of Scheludko and Exerowa (1959) to measure the surface forces in foam films stabilized with various frothers such as pentanol, octanol, MIBC, and PPG. The results were compared with the froth stabilities measured using the shake tests and the film elasticity calculated using the model developed by Wang and Yoon (2006). It was found that the froth stability is controlled by both film elasticity and surface forces (or disjoining pressure), the relative contributions from each changing with frother concentration and type.

Jan 1, 2006

By Keith E. Meyers

Condition monitoring is a viable troubleshooting practice among many industries to extend equipment performance, minimize unplanned downtime, reduce maintenance and repair time and costs, and increase related aspects of plant safety. But obstacles abound for mining, mineral-processing and cement operations striving to implement the technologies. Harsh machine environments can muddy efforts. High vibration in machinery can interfere with wide-spread rollout. Staff expertise or skills may be lacking. And costs may be prohibitive. Fault detection has emerged as a practical and cost-effective solution to identify process and machinery faults before failure interrupts productivity or jeopardizes worker safety. Fault detection can be a stand-alone system or connected to plant automation.

Jan 1, 2005

By Amanda Elioff

Success of the Gold Line Eastside Extension rail tunnels in Los Angeles has prompted Metro?s planning for two new rail lines to include underground alternatives. The Westside Extension Transit Corridor alternatives include up to 17 miles of subway to be constructed in soft ground. The routes will require construction in Los Angeles? ?Potential Methane Zone,? not considered for subway construction until recently. Slurry face TBMs will likely be specified. The Regional Connector, through the downtown area, includes one underground alternative with 1.7 miles of tunnel as well as three underground stations in soft ground and rock. Challenges will include tunnel and station construction under narrow streets. This paper will describe the alternatives, planning, geologic conditions and tunneling concepts for both planning studies.

By X. Shi

This paper presents design and implementation details of a fuzzy-behavior-based controller for an automated excavator. The robotic excavator is equipped with sensors, actuators and an embedded control system. The excavator controller uses neural-networks to interpret forces and torques gathered during the excavation process from bucket-mounted force sensors. Implementation details card experimental results using the fuzzy-behavior-based excavation controller are given for several excavation tasks. These excavation tasks demonstrate some of the complex skills that are essential for an autonomous mining-excavator controller.

Jan 1, 1997

By P. Creevy, P. F. Mousset-Jones, G. Danko, A. D. S. Gillies

The surface heat transfer coefficient is measure of the rate of heat transfer from exposed rock surfaces to the ventilating air. Knowledge of its value is of particular importance to accurately simulate the early stages of rock cooling after the opening of an excavation. A number of theoretical formulae for the calculation of the coefficient are available for use in mine climate simulation. However, direct determination by in situ measurement is preferred. Instrumentation, which has been developed for in situ mine measurement, and experimental procedures involving measurement at varying air velocities, are described. In a major study covering four Australian underground mines, the system has been used to determine surface heat transfer coefficients. A direct relationship was clearly established between the measured surface heat transfer coefficient and air velocity. Comparison is made between experimental results and those previously measured or calculated by others. The relationship established can be described by an equation and holds for air velocities above 0.4 mls. The derived relationship was con- firmed at all mines tested and is independent of geology and tunnel dimensions found in modern mines.

Jan 1, 1991

Federal regulations require the use of methane monitors on all mining machines. All machine-mounted methane monitors currently used in underground coal mines rely on catalytic heat of combustion sensors. As a comparison, although not currently approved for use on underground mining equipment, instruments with infrared sensors are evaluated in this study. Potential advantages of using infrared sensors include faster response time, long-term stability, and reduced maintenance needs. Tests conducted in the laboratory and at a full-scale model mine compare the performance of catalytic heat of combustion and infrared sensors operating under test conditions designed to simulate airflow conditions underground.

Jan 1, 2009

By J. Piper

Markets and Production Beryllium (Be), an extremely light metal, is used in many specialty applications. It the lightest element in Group 2A of the periodic table, with a specific gravity of 1.85 gm/cc, and a high melting point of 12850C (Calvert, 2004). The functional properties of beryllium are stiffness, strength, dimensional stability, resistance to corrosion from acids, and electrical and thermal conductivity. The ability to reflect neutrons and transmit x-rays, makes beryllium irreplaceable in uses such as precision optical components, inertial guidance systems, and in nuclear reactors (Anon, 1993). Beryllium is used in Cu alloys to strengthen and reduce corrosion in copper wire, and in lightweight oxide ceramics that are used as heat sinks, and as electrical insulators. The market revenue of beryllium can be broken down into the seven major groups below, and are plotted on the pie chart in Figure 1 (Anon, 2005). 1.) Telecommunications & Computer 2.) Magnetic & Optical Data Storage 3.) Aerospace and Defense 4.) Automotive Electronics 5.) Industrial Components 6.) Appliance, and 7.) Other.

Jan 1, 2007

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and thus deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the go band to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Feb 27, 2013

By T. Mills, M. Evatz

Newmont’s Lone Tree Mine, located in northern Nevada, is an open pit gold operation supported by a standard truck and shovel mine production fleet (Caterpillar 785Bs and Hitachi EXs). Newmont continues to search for ways to decrease capital expenditure and lower operating cost, hence the implementation of the Ultra Light Body (ULW) concept. The fundamental idea associated with the ULWs is the increased payload potential. Economic justification comes from successful achievement of additional payload, within the truck’s rated GVW, without changing its loading and hauling characteristics. The increase in payload capacity allows equivalent tonnage movement using fewer trucks.

Jan 1, 2001

By G. Luttrell

Coal preparation plants play an important role in modern society by providing high quality feeds for coal-fired utilities, industrial boilers and metallurgical coke facilities. Unfortunately, field data indicate that preparation plants are often not operated under optimum conditions, resulting in lower productivity and lost profits. In many cases, this shortcoming can be attributed to a failure by plant operators (i) to recognize the importance of correctly adjusting plant operating conditions to accommodate requirements dictated by coal sales agreements within different coal markets and (ii) to properly account for variations in product moisture with particle size across different plant circuits. This paper discusses the important influence of moisture constraints on preparation plant optimization and provides a case study to illustrate the potential gains that can be realized via proper understanding of plant moisture control.

Jan 1, 2009

By Scott Ellenbecker

Soon New York City will have a new train station. A tunnel project is under construction to extend Line 7 to a new station that is located near the Jacob K. Javits Con-vention Center. This is also part of the Hudson Yards redevelopment project that is intended to aid redevelop-ment of the west side of Midtown Manhattan around the Long Island Railroad?s Caemmerer Railyard. The station, or ?cavern? as it?s called by those excavating it, will be the portal for that growth. In the city, public transportation means high-rise residential proper-ties will have better access to the business district, and those outside the area will have greater access to event facilities ? two factors that are critical for development investment.

Jan 3, 2010

By Hugh Douglas

In the past two years recent increases in silver prices over levels that prevailed for many years have changed supply/demand patterns. On the supply side, a silver mining boom is in progress in the United States and elsewhere. On the demand side, traditional uses of silver by individuals are dropping while industry is conserving. These changes will alter the supply/demand balance and bring about more moderate rises in silver prices, which in turn will impact the mining industry.

Jan 1, 1981

By John McDonald, Peter C. Raleigh, Christopher Dishlip

This paper will discuss how the construction management team and the contractor working together on the City of Los Angeles, North East Interceptor Sewer project, managed information on a daily basis. Data was synthesized from various sources including: inspection, survey, instrumentation, laboratory and the tunnel boring machine data logger systems to produce state-of-the-art reports and graphics which will become industry standard. Special emphasis is placed on how the data is managed and interpreted in a clear and objective manner, permitting the tunneling processes to be carefully monitored and suggesting appropriate action to be taken by the construction management team and contractor.

Jan 1, 2005