Search Documents

By William R. Yernberg

A conference on coalbed and coal mine methane was held March 27 and 28, 2000, in Denver, CO. The conference, organized by the Strategic Resource Institute, was attended by leaders in the coal mining and gas energy industry. The conference focused on the recovery of methane from coal beds as an energy resource and the removal and utilization of coal-mine methane (CMM) related to underground coal mining. The two-day conference discussed methane resources around the world, methods of recovery, methane markets, underground coal mining, health and safety issues and environmental issues related to methane. The consensus among the presenters is that the future looks promising for coal bed methane (CBM) and CMM.

Jan 1, 2000

By N. B. Pundari

Proper selection of large walking draglines, based on sound engineering principles and field experience, has not kept pace with the large capital expenditures needed to buy these stripping machines. The use of large walking draglines for stripping overburden in US surface coal mines grows steadily, but equipment selection continues to pose problems. An improper size, model, make, or spoil reach selected for a particular stripping application results in additional, unnecessary coal production costs. Large walking draglines are being used to dig deeper tar sands at the Syncrude operations near Fort McMurray in Northern Alberta, Canada. This application is compared with typical deep digging operations and dragline use prevalent at typical US strip mines.

Jan 4, 1981

By C. A. Young, J. D. Miller

The surface chemistry of the calcite/oleate flotation system was examined by in-situ FT-NIR/IRS. Spectra of combination and overtone bands of aliphatic stretching vibrations revealed gauche/trans conformational changes that occurred solely as a function of temperature. The conformational changes were attributed to the simple "melting" behavior associated with phase transitions. It was concluded that chemisorbed oleate at calcite surfaces is gel-like at temperatures below 22oC, resembles a coagel between 22oC and 31oC, and becomes micelle-like at temperatures above 31oC. By comparison, chemisorbed oleate at fluorite surfaces also undergoes these phase transitions but is additionally dependent on adsorption density. The conformational changes were observed at high chemisorption densities (> 2.0x10-10 mol/cm2) and attributed to molecular forces, primarily van der Waal's interactive forces, among neighboring chemisorbed oleate molecules. Similar analysis of in-situ FT-NIR/IRS spectra of surface-precipitated calcium dioleate at calcite surfaces did not exhibit this behavior thereby confirming that surface-precipitated calcium dioleate remains in an all-trans conformation. The results help explain why surface polymerization is not observed at calcite surfaces but is observed at fluorite surfaces.

Jan 1, 2002

By J. L. Page, A. C. Marlowe

The Research and Development Services of South Africa has begun underground trials with a Robbins 52RE blindhole borer using a cutterhead fitted with high pressure water jets to assist mechanical cutting. The objectives of the work are to reduce cutter costs by increasing cutter life and to increase overall penetration rates. The paper reviews blindhole boring in South Africa and laboratory experiments in rock cutting assisted with high pressure water jets. The borer and its ancillary equipment are described. Initial results of underground boring experiments are presented. The paper concludes with the test programme for the future.

Jan 1, 1985

By David M. Jurich, Randy J. Essex, Alex de Aboitiz

An Automated People Mover (APM) transit system is planned for the growing Phoenix Sky Harbor International Airport. The APM will improve passenger movements between the terminals, and provide a link to parking facilities, a new rental car facility, and the planned metro Light Rail. The underground works will include shallow twin bored tunnels, taxiway crossings, and underground stations constructed beneath critical airport facilities. Challenging soft ground conditions will require extensive underpinning and ground improvements. Design is underway, and construction is scheduled to begin in 2007 with project completion in 2015. The owner’s planned delivery method for the APM Project will be Construction Manager at Risk (CMAR) with a Guaranteed Maximum Price.

Jan 1, 2005

By M. Schafer

The 6-m- (20-ft-) diameter cast-in-place tunnel lining for Phase 3 of the Mill Creek Tunnel (MCT3) has been completed. This article summarizes aspects of liner design and ad-dresses the construction approach in placing the liner in areas of tunnel that experienced crown overbreak. Tunnel lining production rates, installation procedures and form buoyancies experienced during concrete placement will also be presented. The Mill Creek Phase 3 tunnel (MCT-3) is expected to be completed this year. It is one of the largest tunneling projects undertaken by the Northeast Ohio Regional Sewer District (NEORSD) to date. The tunnel horizon is situated within the Devonian Chagrin Shale rock formation at an average depth of 85 m (280 ft). The tunnel was excavated using a two-pass method. A full face, fully shielded, Robbins 7.2-m- (23.8-ft-) diameter tunnel boring machine (TBM) was used to excavate approximately 4,500 m (15,000 ft) of tunnel and facilitate installation of initial supports (first pass). The final lining (second pass) consists of 305-mm- (12-in.-) thick cast-in-place reinforced concrete and integral low flow channel. Seven shafts were constructed on the project. The excavation of the tunnel commenced at Shaft 14 and proceeded down grade to Shaft 9, the terminus shaft. Because of the presence of overbreak in the tunnel crown, measures were required to support the form and counteract the effects of buoyancy during concrete placement.

Jan 1, 2008

By Rodney K. Morrison

MARTA, The Metropolitan Atlanta Rapid Transit Authority, is building a 53 mile heavy rail transit system to serve the City of Atlanta. Phase A of the Rail System, consisting of approximately 14 miles of at-grade, aerial and subway construction is underway. Metropolitan Atlanta lies in the Piedmont Geologic province of Georgia and is underlain by rocks of essentially granitic and gneissic nature. The soils encountered are primarily silty sands which are in-place weathering products of the parent rock and exhibit their relic structure. In general, these materials have presented no unique construction problems other than those created-by proximity of manmade structures, local availability of ground water, and top of rock elevation. The subway sections of primary interest in this paper consist of hardrock and soft ground tunnels and extensive cut-and-cover sections. The cut-and-cover construction includes excavations as deep as 80 feet. Temporary support systems in these deep excavations consist of soldier pile-timber-lagging or soldier pile-tremie concrete (SPTC) walls with internal bracing or tiebacks. In shallow cut-and-cover sections, where right-of-way economics permitted, slopes were laid back partially or fully to reduce or eliminate the need for bracing systems. Dewatering systems were required in most open cut excavations. Due to the close proximity of utilities and existing structures to the MARTA

Jan 1, 1979

By Neil F. Archer

Due to the increased chance of violations and shutdowns by the U.S Occupational Safety and Health Administration(OSHA) and the U.S. Environmental Protection Agency (EPA), a company can save itself problems by taking control of the dust caused by conveying material. A complete dust-control policy can keep these emissions confined, sealed and suppressed, protecting the environment from fugitive, airborne dust. Material handling and processing, storage and traffic are the major dust producing sources. All industries that convey dry, light material need a dust control system.

Jan 1, 2003

By D. X. Tang, G. Wilson, S. S. Peng

Design and implementation of a roof bolting plan requires reliable geotechnical information of strata, such as rock strength, and locations of interfaces and voids/fractures. The drilling parameters obtained during normal roof bolt installation cycle provide a fast and economic way to gather information on the geological structure within the bolted horizon. The purpose of this research project is to develop a method for identifying the geological features in the mine roof strata based on drilling parameters of roof bolter. The criterion for void/fracture prediction has been developed and proven valid. This paper focuses on the estimation of the strength of roof strata by using drilling parameters. Based on the results of a series of underground and laboratory tests, feed pressure is found to be the most sensitive parameter when the strength of roof strata changes. Moreover, it was also found that both penetration rate and rotation rate have obvious impact on the magnitude of feed pressure. Based on these findings, the criterion for the estimation of roof strata strength has been developed using the relationship among feed pressure, penetration rate and rotation rate and implemented in MRGIS.

Jan 1, 2006

By Paul Hewitt, Tim Smirnoff

Design and construction of the Epping to Chatswood Rail Line tunnels in Sydney, Australia required an innovative approach to define hydrogeological properties of the Sydney Hawkesbury Sandstone and provided an insight into the hydraulic behaviour of fractured sedimentary rocks. To meet restrictive water inflow and infiltration criteria both the pre-treatment of zones of fractured or highly jointed rock, and waterproofing using an interior spray on membrane for the finished drained tunnels and stations was required. Methods typically used to address the interaction of groundwater and tunnels in the Sydney Basin are demonstrated by case histories from major design-build tunnel projects.

Jan 1, 2005

Amid some of the worst economic conditions that the mining industry has been faced with in more than a decade, the mood among the large crowd at the 114th Annual Northwest Mining Association?s annual meeting was surprisingly upbeat. More than 2,200 attendees showed up at John Asuaga?s Golden Nugget Casino in Reno, NV for the conference held Dec. 1-5. And more than 200 companies exhibited in 240 spaces, including SME and the Minerals Information Institute. The number of attendees and exhibitors were the most for the conference in more than 10 years. The conference was held in Reno/Sparks for just the second time in its illustrious history but began under the cloud of global financial turmoil. Prior to, and during the conference, the industry news headlines were grim, to say the least. An alarming number of mine plans and expansions had been put on hold; hundreds of miners across the United States had been or were in the process of being laid off; commodity prices were falling and some of the biggest mergers in the industry fell through while miners around the world put the brakes on to take a wait-and-see approach. It was a painful time for many, but the downsizing actions taken by many mining companies was exactly what needed to happen, according to Industry Outlook Luncheon featured speaker Frederick Sturm. He is the executive vice president and chief investment strategist and member of Mackenzie?s Investment team. He has earned a reputation as one of Canada?s leading investors in natural-based companies and he also manages the Ivy Global Natural Resource Fund in the United States Sturm said that the mining industry has fallen hard and that he expects it to bounce back quickly, before falling hard again. In these tough times, he said, the companies that have pulled back on production early are doing the right thing in the long run.

Jan 1, 2009

By Aki Fujii, Hiroshi Dobashi, Mitsuro Matsuda, Yoshinari Kondo

INTRODUCTION The Metropolitan Expressway Central Circular Route with a total length of approximately 47 km is located outside the Inner Circular Route of Tokyo (at a radius of approximately 8 km from the city center). Sections with a length of approximately26 km, slightly less than 60% of the total length, on the east and north sides are in ser-vice. Completing the Central Circular Route (Figure 1) is expected to enable through traffic concentrated at the city center to get around, and to form a well balanced trans-port network, which will alleviate traffic congestion considerably. The Central Circular Shinjuku Route, a section with a length of approximately 11 km on the west side, is now being constructed at a fast pace. The route is being built mainly by the shield tunneling method to carry out work smoothly under a trunk highway carrying heavy traffic and to reduce adverse effects of tunneling work on residents in the neighborhood. Shield tunnels have recently been becoming longer and deeper, and no secondary linings have been used in an increasing number of cases because of the over-crowding of cities or the reduction of budgets for public works. Economical, durable and high-quality segments have been required for linings of shield tunnels. Segments are made of concrete, steel, cast iron or combination thereof. Concrete segments are generally used in shield tunnels of medium to large diameter. Concrete segments are highly durable and resistant to compression, so they are highly resistant to earth pres-sure, water pressure and jack thrust. They are, however, heavy and have low tensile strength, so they are brittle and their corners are likely to spall. Concrete segments should therefore be handled carefully.[1] The authors have developed a steel fiber reinforced highly flowable concrete segment (referred as SFRC segment) that overcomes the weaknesses of concrete segments[2] to construct economical, durable and high-quality linings. SFRC segments have been applied to outbound sections SJ51 through SJ53 of the Central Circular Shinjuku Route. Unlike conventional concrete segments (referred as conventional RC segments), SFRC segments are made of steel fiber reinforced self-compacting highly flowable concrete. SFRC segments require less reinforcing bars than conventional RC segments because steel fibers are expected to work as reinforcements. Steel fiber reinforced concrete is a composite material that overcomes the brittleness of plain concrete, and has higher resistance to bending, tension and shear than

Jan 1, 2007

By Tim O’Neil

If you build a big truck, build a big tire to match it. Let that haulage synergy aid the economics, productivity and lessened maintenance for the unit. Now, Cater-pillar and Michelin have done just that. Discussions began in 1996. Caterpillar was making plans for its 797 ultra-class haul truck. The development team realized the need for a tire that could withstand extreme loads. The 797 would weigh 558 t (615 st) and be capable of 64 km/h (40 mph) speeds. So Caterpillar approached Michelin. The two companies realized the benefits of jointly developing a tire for the 797.

Jan 1, 2002

By Lane White

The 1989 Annual Meeting and Exhibit of SME in Las Vegas, NV, February 27 - March 2, 1989, was the largest ever, drawing more than 4000 regis¬trants and 240 exhibit booths. Technical sessions included presentation of nearly 500 papers, including symposia on Biotechnology in Minerals and Metals Processing, Surplus Capacity in the International Metals Industry, and APCOM `89 - the 21st International Symposium on Application of Computers and Operations Research in the Mineral Industry. Technical sessions covered the gamut of minerals industry interests; however, the proximity of the meeting to recently surging gold development in Nevada drew special attention to gold operating practices. Several of the papers on gold processing are reviewed below. To keep pace with the strong world- wide interest in gold development, SME has scheduled three additional upcoming programs that will focus specifically on gold: World Gold '89 - Gold Forum on Technology and Practices will be held November 5 - 8, 1989 in Reno, NV, as a joint meeting and exhibit between SME and the Australasian Institute of Mining and Metallurgy. Technical sessions will encompass a full program of papers covering geology and exploration, mining, and mineral and metallurgical processing. Cooperating sponsors for this meeting include the Canadian Mineral Processors Division of CIM, The Institute of Metals, The Institution of Mining and Metallurgy, The Mining, Geological & Metallurgical Institute of India, and The South African Institute of Mining and Metallurgy. Gold '90 - Salt Lake City, UT, February 26 - March 1, 1990, will be a symposium held in conjunction with the 1990 SME Annual Meeting. Current research on the processing of refractory gold ores will generate innovative papers on process mineralogy at this symposium, with special emphasis on gold with pyrite and gold with carbon. Other sessions are planned for gold exploration and mining, gold metallurgy, gold plant design and practice, and gold in scams. Advances in Gold and Silver Processing Conference, October 1 - 3, 1990 will be held in Reno, NV. Preliminary planning calls for technical sessions on heap leaching practice, refractory ore processing, non-traditional lixiviants, bioleaching, metal recovery from solution, and the environmental aspects of processing operations. PLANT DESIGN, OPERATION Technical sessions organized by the Minerals and Metallurgical Processing Division of SME at this year's meeting in Las Vegas covered a wide range of gold operating practices. Eight papers relating to gold plant design, operation, and equipment are summarized here. Preprints of these papers are available by writing to Publications Sales, PO Box 625002, Littleton, CO 80162-5002 ($2.50 per paper for AIME members, $4 for nonmembers). Continuous elution process A. M. Stone, of Bechtel Australia Pty. Ltd., described the "Development of the Continuous Elution Process for Extraction of Gold from Carbon" (pre-print 89-75). Developed by Bechtel Pacific Corp. for Ok Tedi Mining Ltd., the Continuous Elution Process uses the same reagents as batch processes for elution of gold from carbon, while yielding significant savings in stripping vessel size and energy consumed in comparison with equivalent batch processes. The process is also simpler to operate than batch processes. Other advantages include reduced maintenance costs, higher average eluate grade, and near steady final eluate grade. Pilot testing for the Continuous Elution Process was conducted at Western Mining's Kambalda gold plant beginning in December 1982. The Continuous Elution Process is a continuous countercurrent system operating in a pressure vessel at elevated

Jan 1, 1989

Bortech’s BoreClad corrosion protection system will be displayed at MINExpo. BoreClad is an innovative system for inside diameter cladding of nozzles, tubes and other circumferential devices. Pressure vessels, mud pumps and other mining equipment must be protected from corrosive caustic chemicals. Usually manufactured from mild steel, they can be clad with a protective material, such as stainless steel, to provide corrosion resistance. However, most welding processes leave voids where corrosion can damage the base metal. BoreClad provides void-free welds by combining gas metal arc welding with automated feed and rotation of chuckable parts. Workpieces of up to 915-mm- (36-in.-) long with a 460-mm- (18-in.-)swing can be clad with stainless steel, Iconel or other exotic metals. In addition to eliminating the voids associated with hand welds, BoreCladcan lay more than 2.2 kg/h (5 lbs/hour) of metal. That is a significant reduction in weld time. Web sitewww.bortech.com.

Jan 1, 2004

By Kerry Spickelmier

Editor's note: information for this feature was taken from the published APCOM proceedings. Computer trends, with special focus on the reasons for computer use, grabbed the lion's share of attention at the 23rd worldwide meeting on the Application of Computers and Operations Research in the Mineral Industry (APCOM 23). However, technical topics did not provide the meeting's sole focus. The last-minute inability of certain former communist countries to fund the travels of a few scheduled speakers was a reminder that science does not operate in a void. As with all technical progress, the APCOM presentations raised interesting questions regarding interrelated organizational dynamics and political and socioeconomic issues. Consider US Bureau of Mines (USBM) research to design an expert control systems to "duplicate" an experienced, "good" operator during automated underground roof bolting. In his presentation of the project, Takach, Jr. stressed the importance of preserving the ability to switch from automatic to manual drilling control. From a technical standpoint, this allows the expert system to "learn" from a good operator. As important, he said, is that this flexibility decreases the human operator's sense of being replaced by the machine. The question arises: Which will loom larger in union minds, increased operator safety through remote opera¬tion or the potential for total operator replacement? Like any new product, computer technology relies on marketing to aid its acceptance and use. Consider, too, a decision support system, by Schena and Gochin, for mineral resource management in a developing country. The authors said "the analysis permits the assessment of the overall socioeconomic consequences of mineral prospects and allows incorpo-

Jan 1, 1992

By K. A. Lewandowski

Agglomeration techniques are widely used by industry to form fine particles into larger masses that are easier to handle and process. One area where agglomeration is potentially useful is in heap leaching operations. With-out agglomeration, fine particles travel through the heap, clogging the spaces between the larger particles and resulting in poor leach solution flow. Poor flow of leach solution will result in long leach rates and/or decreased metal recovery. Agglomeration immobilizes the fine particles and therefore improves heap permeability to fluid flow. Additional additives (binders) are needed to prevent agglomerates from breaking up as leaching solution percolates through the heap. Type II Portland cement and lime are two well-known binders used in gold and silver leaching, but these are limited to alkaline leaching environments. Various other products have been tested as binders, including polymers. This paper summarizes the benefits of agglomeration in heap leaching and the results obtained from the testing of several different agglomeration binders in heap leaching operations.

Jan 1, 2009

By Theodore S. Jordan

The discovery of a major porphyry-type copper deposit on the Papago Indian Reservation in Pinal County, Arizona was announced by El Paso Natural Gas Company in 1968. The deposit, known as the Lakeshore Property, contained an estimated 470 million tons of sulfides and oxides averaging 0.75 percent copper. History and Geology of the area have been described by Harper and Reynolds (1969). El Paso subsequently&apos; entered into the agreement for joint development of the property with Hecla Mining Company, with Hecla as the operator. The ore body consisted of three types of mineralization: 1) Disseminated Oxide Ore, <1% Cu 2) Disseminated Sulfide Ore, <1% Cu 3) Tactite Ore, >1% Cu

Jan 1, 1985

By B. Anameric, S. K. Kawatra, K. B. Rundman

The iron nugget process is an economical, environmentally friendly, cokeless, single-step pig iron making process. Residence time dependent process requirements for production of pig iron nuggets at a fixed furnace temperature (1425 C) were investigated. Three chemically and physically different products were produced after complete reduction to iron, depending on the residence time in the furnace. These products were direct reduced iron (DRI), transition direct reduced iron (TDRI), and pig iron nuggets (PIN). The increase in the carbon content of the system as a function of residence time was detected by optical microscopy and Microhardness measurements. Sufficient carbon dissolution for the production of pig iron nuggets was obtained after 40 minutes residence time. The pig iron nuggets produced had chemical and physical properties similar to blast furnace pig iron. They were liquid state products and slag was completely separated from the metal.

Jan 1, 2005

By Gui DeReamer

Located on the Wabash River in the central portion of the state, the city of Lafayette, IN is relatively small compared to most cit-ies that incorporate tunnels into their combined sewer overflow (CSO) systems. The original CSO plan for the city was to replace two aging lift stations that were built in the 1950s. The original con-cept was to build a new sewer using conventional cut-and-cover construction to eliminate one of the lift stations ? the Parking Lot Lift Station ? and build a new regionalized one at the location of the Pearl River Lift Station. The initial sewer design was sized just to handle the flow that would eliminate the Parking Lot Lift Station. The planning for this project was being developed as part of the city?s CSO long-term control plan (LTCP) that focused on reducing the overflows from the city?s 14 overflow points. However, during the development of the CSO LTCP, a major industrial user indicated it would be increasing its flows to the system, which required additional conveyance capacity to meet the city?s CSO LTCP. After reviewing the design concepts with city representatives during the planning phase of the project, the mayor indicated that he wanted to minimize impacts to downtown businesses; therefore, trenchless alternatives were considered. The last piece of the puzzle that drove the project away from a small diameter pipeline was discovered during a flow monitoring program to collect flow data for the CSO LTCP project. This study revealed a major restriction in the 100-year-old Pearl River Trunk Sewer, located beneath four active railroad tracks. To eliminate this flow restriction, provide more overflow storage and reduce the impact to local businesses, a new 2.7- to 3.6-m- (9- to 12-ft-) diameter tunnel sewer became the most viable solution.

Jan 1, 2011