Search Documents

By Kym L. Morton

Ground water and associated pore pressure represent elements which can have a negative impact on surface mining and slope stability. Ground water flow and deformation within a slope influence each other. An increase in pore pressure will result in a decrease of effective stress; and conversely if the pore pressure decreases, the effective stress increases. Slope analysis and slope design calculations require good information on pore pressure distribution around an open pit excavation. Until recently very little pore pressure data was available and assumptions had to be used. Location and design of measuring points depend on geological and structural setting, geotechnical domains and practicality. Good planning and the use of sensitive point piezometers to measure in situ pore pressures means that real-time data can be collected and used for the construction of flow nets, the determination of pore pressure distribution around an open pit mine, the validation of the dewatering/depressurization requirements, the calculation of the efficiency of the dewatering system and finally the use of pore pressure data in slope stability analysis. The recommended layout for a monitoring system, types and design of piezometers, data collection and use of the pore pressure data are presented.

Jan 1, 2008

By Paul Fouchè, Danie van der Merwe

Contents ?Purpose ?Introduction ?Development of RF tracers ?Test procedure ?Results ?Conclusion ?Way forward ?Acknowledgements

Jan 1, 2005

By S. Özgen

In this study, the possibility of beneficiation of chromite tailings in the Uckopru/Fethiye-Turkey region by a combination of hydrocyclone and multigravity separator (MGS) was investigated. The two significant operational parameters of hydrocyclone, which were diameter of the apex and diameter of the vortex, and the three significant operational parameters of the MGS, which were drum speed, tilt angle, and wash water, were varied and the results were evaluated with the central composite rotatable design. In order to produce a chromite concentrate by hydrocyclone and MGS, mathematical model equations were derived by computer simulation programming, applying the least-squares method using Minitab 15. Second-order response functions were produced for the grade and recovery of chromite concentrates.

Jan 1, 2012

By M. H. Moys

Accurate models of mill power are becoming more necessary as the design, operational, and control requirements for grinding mills become more stringent. Models of mill power are reviewed briefly, and a new semi-phenomenological model is derived. The conventional torque-arm model for mill power is combined with a model of the tendency of the load in a mill to centrifuge at high speeds, to describe mill power that can be related to several design variables (such as mil geometry, mill speed, and liner design) and control variables (such as load volume, slurry rheology, and mill speed in the case of variable-speed milling). The semiphenomenological nature of the model allows rational conclusions to be reached concerning the effect of various aspects of mill-load behaviour on mill power. The model is shown to be capable of describing reality with much greater accuracy than is achieved by empirical models such as the Bond model.

Jan 1, 1993

By P. A. Corbeil, C. Swart, F. Miller, V. Falmagne

Automation technologies are increasingly adopted in different mines worldwide. This paper presents the technical aspects of vehicle automation applications at two Noranda operating mines. Teleoperation of 5 LHD’s at Noranda’s Bell Allard mine is used in order to meet aggressive mining requirements under difficult conditions. The equipment is performing under high demand for reliability and performance. In order to further increase performance, automated loading has been commissioned on one of the LHD’s and is being tested. Results to date indicate improved performance with respect to an operator through better filling of the bucket, fewer passes at the muck pile and shorter cycles. Noranda’s Brunswick mine is currently commissioning an automated haulage zone where two optically guided trucks transport ore from a remotely operated chute to two ore passes. Expected operational advantages include increased system capacity and enhanced safety and comfort for the operator. Monitoring to date indicates that the trucks can operate reliably under the conditions imposed by mine production.

Sep 1, 2001

By Penswick D.

From the perspective of management control, most mining operations can be represented by a hierarchy comprising four layers. The base of this hierarchy consists of the individual pieces of equipment that are used to break and transport rock. The next level comprises the coordinated interaction between different pieces of equipment, termed a process. An operation results from the bringing together of different processes within a common discipline, such as mining or hydrometallurgy. Finally, an enterprise is formed when the separate mining, concentrating and smelting business units are combined. To date, much of the literature written on the topic of mining automation has focused on the equipment level, specifically on removing the operator from production mining equipment. This focus should not, however, overshadow advances registered in automation at both the process and enterprise levels. Only at the operations level of the hierarchy has little progress been made. While automated equipment, process management and enterprise resource planning are a current reality; it is argued that the benefits from automation have, to date, been largely elusive. It is further argued that full benefits of automating other levels will only be fully achieved when this ‘gap’ in the mining automation hierarchy has been addressed and an uninterrupted, process-wide information flow across the entire operation is achieved. Furthermore, it will be reasoned that so-called vertical integration can only be achieved with an automated operational level in place. It is believed that all the necessary building blocks are in place and that the industry is ready for this development. The paper concludes by presenting a vision for what operational level automation would achieve.

Sep 1, 2001

By R. Ajalloian, L. Karimzadeh

This paper describes the engineering properties of Givi dam foundation. Givi dam will be built across the Givi River on the andesitic rocks (Karaj formation) in Ardabil province (northeast of Iran). Geotechnical investigations including drilling, pumping tests, sampling for laboratory testing and discontinuity survey. Physical and mechanical properties of andesitic rocks such as density, water absorption, porosity, uniaxial compressive strength, triaxial compressive strength, durability and direct shear tests are evaluated in this paper. Discontinuity data are process for the determination of dominant sets and for the rock mass characterization in terms of classification systems ( RMR, Q and RSR ). Correlations between these three classifications are discussed. Le barrage doit être construit sur la rivi_re givi qui cou_e sur les andesites (formation de Karaj)dans la province d_ Ardebile situee_ a Nord- Ouest de l_ _Iran. Les études géophsique commesondage, Pompage. Et échantillonnage afin de verifier les discontinutés out éte_ effectuées. Lesproprietés physique et méchanique des roches andesifique ont éte_ verifieés. Les informations concernaüt aux discontinuitiés afin de montrer leur principale direction ont éte_ verifieés, les proprietés des roches dans leurs ensemble ont éte_ etudieés. Les divers classifications(RMR,Q,RSR ) ont éte_ comparés et analyseés. Dieses Schreiben ist zur Erklaerung der Ingenieureigenschaften ueber Baugrund des Givi Deiches.Dieser Deich soll im Givi fluss auf Andesitgesteine (Karaj formation) gebaut werden. Der platzdes Deiches legit im Ardebil Provinz nordwestlich von Iran. Geotechnische Untersuchungen Sind:Bohrungen, pumpen Versuche, Probenentnahme fuer Laborversuche, BrechbarkeitBestimmungen, physikalische und mechanische Eigenschaften der Andesitgesteine wurde hierausgewertet, wie Z.B.: Wasserleitfahigkeit, Porositaet, Scherfestigketswiderstand, Informationenueber Brechbarkeiten der Gesteine wurde gesamelt, und die meisten Brechbarkeiten bestimdamitman die Gesteine besser klassifizieren kann. In Endefekt wrid die Resultate verschiedeneKlassifizierung wie RMR, Q, und RSR besser geachtet und zusammen vergliechen.

Jan 1, 2003

By M. B. Dunn

Terminals form part of the transportation chain from producer to consumer in the world-wide conveyance of bulk commodities. As such, they are a vital link in providing a buffer between widely differing transporation modes. It is essential in the conceptual design of such terminals that an overall view of the entire system of which they form a part is taken. Only in this way can it be ensured that the system will operate smoothly and without disruption, for in the end such disruptions can have dramatic repercussions, both on the cost of the commodity in the market place and on production. In this respect, computer simulation is a useful tool in arriving at the optimum design for the system. The Richards Bay Coal Terminal provides a good example of such an approach. Commissioned in 1976 to handle 12 Mt per annum, it is now handling 24 Mt per annum, with plans for further expansion to 44 Mt per annum in the future.

Jan 1, 1980

With a number of new mines at the feasibility stage and beyond and with several pellet capacity expansions well underway to reduce sintering activity, Alex Broad looks at the impact of worldwide environmental legislation on the iron ore industry. 'Environmental impact assessment' has become something of a buzz term in the metals and mining industry over the last few years and is sure to be an integral part of any green or brown-field project worldwide by the turn of the century, if it is not already. Given the number of iron ore projects springing up, most notably in deposit-blessed Australia, it is not surprising that the subject of environmental approval has been raising its green head. At the very least the process can slow down a new mine project, or at worst have it deemed unfeasible but in general a government is unlikely to put up unnecessary barriers to a project with the beneficial financial implications of an iron ore deposit.

Jan 1, 1996

By R. J. Davidson

The mechanism of gold adsorption on activated charcoal by R. J. DAVIDSON: M.Se., Ph.D. (Rhodes) (Visitor) The adsorption of gold onto activated charcoal is most dependent on the concentration and character of the 'spectator' cations present in the adsorption medium. In the presence of calcium ions, gold is adsorbed as the calcium aurocyanide complex. The degree to which the aurocyanide complexes are adsorbed follows the series Ca> Mt:> H> Li> Na> K, calcium aurocyanide being the most stable complex and potassium aurocyanide the least firmly bound. If a loaded charcoal, where the gold is present as the calcium complex, is treated initially with either sodium carbonate or potassium carbonate solutions, the gold can subsequently be eluted from the charcoal with hot deionized water as either the sodium or the potassium complex respectively. The elution of gold with deionized water appears to be most attractive practically and economically, and has several potential applications in the recovery of gold from dilute solutions.

Jan 10, 1974

By R. M. Falcon

The paper opens with a summary of the major factors responsible for spontaneous combustion in coal discards. These include heat arising from the oxidation of coal and pyrite, and from the weting of dry or oxidized coal and pyrite; and certain petrographic conditions leading to self-ignition of the coal such as low rank, the presence of a high proportion of reactive constituents, and the occurence of highly porous and botanicaly structured inertinite macerals, The analyses of 6 samples from 2 discard dumps in the Witbank coalfield are included, which show that, according to a three-grade classification of liability to spontaneous combustion, one dump is 'reasonably liable' and the other is 'most liable', It is pointed out that factors other than liability to self-ignition determine the possible utilization of such discards, and that the prevention of oxidation is of great importance if they are to be utilized and spontaneous combustion to be prevented,

Jan 1, 1986

By P. J. Kinver

This paper deals with the development of the cut-and-fill mining method at the Broken Hill orebody of Black Mountain Mineral Development Company (Pty) Limited, at Aggeneys in the north-western Cape Province of South Africa. Lead, copper, zinc, and silver are produced. Production started in January 1976, being confined to blasthole production methods in the upper, steeply dipping areas of the orebody. This blasthole reserve is 70 per cent depleted, and pillar extraction is in progress. The balance of the production tonnage, 60 kt per month, is produced from three cut-and-fill stopes situated in the flatter-dipping areas of the orebody. The cut-and-fill mining method at Black Mountain is a result of research and planning activities that included the use of modelling, laboratory tests, mathematical analyses, in situ tests, and experience gained from other mining operations. These investigations and the resulting developed methods and designs are summarized in the paper.

Jan 1, 1985

The treatment of gold-plant tailings with ferrous sulphate to remove the cyanide is currently in use, on several gold plants. In some cases there is scope for optimization the process. The present work provides a detailed study of the reaction between cyanide and ferrous sulphate. Optimal conditions for the removal of total cyande required a ph of 5,.5 to 6,5 and an Fe:CN molar ratio of 0,5. Ferrocyanide ion is shown to be unstable In aqueous acidic solution, with rapid oxidation to ferricyanide, (Fe(CN) 6 ), and formation .of Fe(CN)5H2O3- at pH values below 4, The precipitate from the reaction between cyanide and ferrous sulphate consists mainly 01 Insoluble Prussian blue, Fe4[Fe(CNI&!.3,and IS shown to be unstable in the presence of alkaline solution, since it decomposes rapidly at pH values above 7 to form ferrocyanide, (Fe(CN)6 ), in solution and various insoluble iron oxides,

Jan 1, 1992

By R. C. M. van der Spuy

The heavy-minerals plant at the Palabora Mining Company treats 25 to 30 kt of new feed daily. The U3Og value of the ore averages approximately 40 p.p.m. The circuit consists of four stages of upgrading on 68 Reichert cones, fol. lowed by a jig and 30 table decks. The paper describes how feed-distribution problems have been overcome and the methods used for monitoring and controlling the cone performance. The adaptation of a standard jig for the recovery of fine minerals is discussed, and a method of 'table agglomeration, for the recovery of coarse refractory copper sulphide is described. The tables consist of polyurethane-covered fibreglass decks, and their operation is controlled according to measurements of the uranothorianite content of the concentrates and middlings by means of a nuclear scintillation counter. The upgrading ratio of the uranium mineral by gravity concentration is 1000:I, baddeleyite (ZrO.) being recovered as a by product.

Jan 1, 1982

By P. J. Petit

Financial evaluation is necessary to investigate the viability of implementing and/or utilising new technology in mining projects. It establishes a techno-economic base for decision-making and justifies capital expenditure. This paper aims to present a monetary appraisal of the electric rock drilling system in a typical feasibility project, whose purpose is to increase the production rate. The in situ environment is a platinum orebody, and the stoping operations occur in UG2 reef. The results are a function of production requirements, technical parameters and financial outlay of the drills. The costs involved in implementing and operating electric rock drills are assessed to the current method of drilling, namely the compressed air operation. A comparison of the electric and pneumatic rock drills in terms of financial outlays for drilling and service requirements, peripheral equipping and training is discussed. Other factors that affect the business case are technical advantages, safety and risk management and the environmental objective of the company.

Jan 1, 2006

By C. Zangerl, K. F. Evans, S. Loew

ABSTRACT: Settlements above fractured crystalline rock masses are rarely observed and in the past, geotechnical engineers would not expect substantial subsidence to occur in association with a deep tunnelling project. However, recent high precision levelling measurements along the Gotthard pass road in central Switzerland, have revealed up to 12 cm of subsidence along sections that pass several hundred metres above the Gotthard highway tunnel. Large-scale consolidation resulting from tunnel drainage and pore pressure changes in the rock mass are believed to be the contributing mechanism. This paper presents results from an extensive numerical modelling study focussing on the processes responsible for this subsidence. Results derived from 2-D discontinuum (i.e. distinct-element) and continuum (i.e. finite-element) modelling show that both discrete fracture deformation (i.e. fracture closure and shear) and poro-elastic consolidation of the intact rock matrix equally contribute to the observed magnitudes and shape of the surface subsidence trough. RÉSUMÉ: Des tassements aux dessus de massifs cristallins sont rarement observés et par le passé les géotechniciens ne prévoyait pas de subsidence significative associée avec des projets de tunnel profond. Cependant, de récentes campagnes de nivellement haute précision le long de la route du Col du Gotthard (Suisse centrale), ont mis en évidence des subsidences atteignant 12 cm sur des sections passant plusieurs centaines de mètres au-dessus du tunnel routier du Gotthard. Le mécanisme invoqué pour expliquer ce phénomène est la consolidation à grande échelle due au drainage du tunnel et aux variations de pression de pore dans le massif rocheux. Cet article présente les résultats d’une modélisation numérique intensive mettant l’accent sur les processus responsables pour la subsidence. Ces résultats obtenus grâce à des modèles 2-D discontinus (p. ex. éléments distincts) et continus (p. ex. éléments finis) montrent que la déformation sur des fractures discrètes (fermeture de fractures, cisaillement) ainsi que la consolidation poro-élastique de la roche intacte contribuent également aux magnitudes et aux géométries de subsidence observée en surface. ZUSAMMENFASSUNG: Beachtliche Oberflächensenkungen in einem kristallinen Gebirge, deren Ursache im Vortrieb eines mehrere hundert Meter tiefgelegenen Tunnels liegt, wurden bisher nicht erwartet und beobachtet. Dennoch wurden nach dem Bau des Gotthardstrassentunnels, entlang der Gotthardpassstrasse Oberflächensenkungen mit einem Maximalbetrag von 12 cm bei der Auswertung von Präzisions-Nivellements entdeckt. Dieser Maximalbetrag wurde in einem granitischen Gneis gemessen. Die örtliche Übereinstimmung zwischen dem maximalem Senkungsbetrag und dem maximalem Wasserzufluss zum Tunnel, und die zeitliche Abfolge von Tunnelbau und auftretenden Oberflächensenkungen lassen hydromechanisch gekoppelte Prozesse als Ursache dieser Gebirgsverformungen vermuten. In dieser Arbeit werden die Ergebnisse ausgedehnter prozessorientierter numerischer Simulationen präsentiert. Resultate aus den 2-D Diskontinuum (d.h. distinct-element) und Kontinuum (d.h. finite element) Simulationen zeigen, dass beide Verformungsmechanismen, d.h. an diskreten Brüchen und der intakten Gesteinsmatrix, gleichbedeutend für die beobachteten Senkungsbeträge und der Form des Setzungstroges verantwortlich sind.

Jan 1, 2003

By J. H. Viljoen, A. Heyns, J. F. Morrison, C. H. Wyndham, N. B. Strydom

Discussion M. J. Martinson* (Associate Member): This is another interesting paper in the series which the Human Sciences Laboratory is publishing on the physiological cost of the more strenuous manual tasks performed underground. As a mining engineer-albeit presently an academic one -this contributor is more concerned with the practical significance of the study in the field of stope cleaning than with physiological niceties, but before discussing some of the practical issues raised by the paper perhaps the authors would care to reply to lay comment on three physiological matters. Firstly, in two places the authors make statements to the effect that the maximum oxygen intake of 'average' (sic) Bantu mine workers is 3.0 l/min. What do the authors mean by 'average'? Maximum oxygen intake in the individual is probably some function of inter alia age, physical fitness, state of health, ambient partial pressure of oxygen, diurnal and/or seasonal changes in metabolism, and possibly cumulative exposure to dust and other occupational contaminants. Since maximum oxygen intake is apparently such an important quality in manual labourers we ought to have a clear picture of its distribution in the entire labour force, and also know precisely how the individual's quantum is affected by factors such as those mentioned above. Secondly, arising out of the same statements and ignoring the reservation implicit in the previous paragraph, is it correct to say that the 'average' Bantu mine worker has a maximum intake of 3.0 l/min? In the August 1966 issue of the South African Journal of Science four of the present co-authors reported the mean maximum oxygen intake of a random sample of 338 Bantu recruits of different tribes to be 2.63 l/min with a standard deviation of 0.542 l/min, and these figures were repeated in a paper published in the November 1968 issue of this Journal. Admittedly the mean maximum oxygen intake of the six subjects used in the present study was 3.05 l/min, but since they were selected on the grounds of previous shovelling experience they can hardly be regarded as being 'average' recruits. Thirdly, it seems to me that the authors are perhaps a little uncritical in their acceptance of the '50 per cent of maximum oxygen intake' level of activity for endurance work. I am not unmindful of the evidence upon which this level is based, but I suggest that the evidence is at best tenuous and that the whole topic of fatigue and 'optimum' levels of productivity under conditions of high muscular activity and considerable psychological stress is a lot more complicated than would appear from the authors' ready acceptance of the 50 per cent level. Under present working conditions the question is largely rhetorical because it would need an army of supervisors to ensure that all members of a typical gang work at 'optimum' levels throughout the shift, but if individual performance should ever become more readily determinable the issue might become crucial to management and malayisha alike. So much for physiological matters; now a few random thoughts on some wider, practical issues raised by the paper. In the paragraph headed Material the statement is made that 'The mixture (of fine, medium-sized and bigger rocks) was considered to be representative of an average underground rock sample'. Elsewhere in the report the authors specifically draw attention to the effect of particle size on the oxygen consumption of men shovelling graded material, and intuitively one imagines that the size distribution of the material being shovelled would be highly significant in a study such as this. Presumably the authors were forced to assess size distribution subjectively because of the lack of objective data on the subject, and possibly the necessity for this assumption highlights how little we know quantitatively about any of the variables in stope cleaning systems. In this connection it may be remarked that although the present study was largely designed to show how dip and stoping width effect energy expenditure in shovelling, no data are given-nor, probably, are they available-to show how the industry's stoping tonnage is distributed in terms of these two factors. It seems to me that if the mining industry seriously hopes to improve stope productivity it must start by measuring the basic variables in existing systems. Elaborating somewhat on the previous paragraph, there also seems to be a tremendous gap between the present study-and its predecessors-and the prospect of gainfully using the information so carefully garnered by the authors. It would be reassuring to hear from the authors that their work on the physiological aspects is being integrated in some master plan for increasing productivity of manual labour. This I fear is not the case, and if productivity has changed at all in recent years I would hazard a guess that the change has been brought about by random factors rather than by systematic engineering design. The Human Sciences Laboratory has worked extensively in stopes in the past, and possibly the time has come when it should widen the ambit of its operations to include engineering-type analyses of cleaning systems, with particular emphasis on the economics of rapid cleaning by manual labour. Perhaps experiments could be conducted with stakhanovite-type gangs consisting of men selected for their high maximum oxygen intake and superior motivation; these men might be offered special incentives in the shape of extra pay

Jan 10, 1969

John Keith Elers Douglas recently retired from active participation in the activities of the South African Institute of Mining and Metallurgy after over forty years of diligent and valuable service to the Institute. This account of his contributions to the mineral industry and associated organizations is presented as a tribute to all his hard work and dedication. Mineral processing The Fourteenth International Mineral Processing Congress, sponsored by the Canadian Institute of Mining and Metallurgy, is to be held in Toronto from 22nd to 27th October, 1982. The theme of the meeting is 'Worldwide industrial application of mineral technology'.

Jan 1, 1981

By G. L. Smith

[Research and development conducted by CSR.-Mining Technology in the areas of active continuous miner based coal dust/methane explosion suppression systems, passive 'bag based, atone dust barriers systems, din and positioning of refuge bays, integrated escape and rescue strategies, and neural network based coal dust/methane explosion risk assessment is briefly described. It is concluded that effective catastrophic risk management of coal dust/methane explosions is dependent on an integrated, systems approach drat encompasses fundamental understanding of hazard sources, qualitative and quantitative probability of occurrence, magnitude of consequences and efficacy of control and recovery measures.]

Jan 1, 1999

The possibility that type 430 stainless steel can become sensitized during annealing after hot-rolling was studied by simulated cycles of continuous-annealing heat treatments, and by calculation of the carbon solubility. It was found that the lower-carbon steel could be sensitized at lower annealing temperatures than the higher-carbon steel, which is in line with plant experience. The difference in sensitization behaviour is ascribed to the lower rate of recovery of the lower-carbon steel during cooling, since recovery is sensitive to the grain size. At practical heat-treatment temperatures, austenite formation does not play a role.

Jan 1, 1996