Search Documents

By Hannweg L. A.

In a first for the diamond industry, Koffiefontein Mine in the Free State, South Africa, opted for the front cave mining method to extract a 90 metre high block of kimberlite ore. Block caving, because of its high initial capital requirements, resulting in a negative internal rate of return (IRR),was ruled out as a feasible mining method for Koffiefontein Mine. Front caving is essentially a combination of the traditional block cave and sub-level cave mining methods, but uses two or more levels of retreating drawpoints. Two extraction levels, in the case of Koffiefontein Mine, are spaced 12 m apart vertically, with the upper 478 m level (48Level) acting as the undercut/extraction level, and the lower 490 m level (49 Level) as the extraction level. Caving is achieved by undercutting a small column of ore, which is then drawn, on both the 48 and 49 Levels, until the planned extraction percentage is achieved. The next column of ore is then mined by advancing the undercut (48 Level), and the process is repeated until the entire ore block is depleted to the contact. Caving-by-gravity techniques of mining rely on closely controlled draw of the caved ore to ensure proper caving action and to minimize the dilution of ore with waste material from the open pit. This paper discusses the need for, and implementation of, a draw control system at Koffiefontein Mine — a computerized production management system, and a draw control system based on linear programming, to allow control over the draw rate and mining sequence — a major factor in all production planning to optimize production efficiency, ore recovery and cave management. Keywords: Draw control, Koffiefontein Mine, Front cave, Caving

Sep 1, 2001

By J Cahill, M Lee

Leinster Nickel Operations, located in Western Australia, consists of an underground and three open pit mines in relatively adverse ground conditions. This paper reviews our ground control practices in the open pits, covering aspects of ground support, wall control and monitoring. These methods have been effective in allowing mining operations to continue beneath unstable slopes. In particular, the use of Groundprobe?s Slope Stability Radar has enabled the Harmony Open Pit to safely operate for months following indication of failure from traditional methods. This case study highlights the benefits of investing in appropriate slope stability monitoring systems.

Jan 1, 2006

By A. V. L. Narasimham

The practice of refractory lining in Fe Cr furnaces is purely based on the behavior of various refractories used in different parts of the Furnace at elevated temperatures. The choice of the pattern of lining is mostly done on traditionally based concepts. Refractory Lining of a furnace is the most crucial enabler for operational excellence for Ferro Alloys production. During the last few years, no major technological change has taken place in ?Refractory Lining Management?, only freeze lining concept is becoming popular. Many ferro chrome furnaces today, have the refractory lining problems especially at tap holes, resulting in shutdowns and production losses. The author with his experiences for the last 37 years in furnaces of all sizes tried to attempt to investigate into the reasons for premature failure of lining.

Jan 1, 2007

By Arvi Parbo

I would like to use the occasion to reflect on how the world environment for the minerals industry is undergoing substantial change, and how this change may affect the industry. I have given my talk the title 'The Quest For Competitive Edge', because the net effect of the changes taking place is that competition is increasing. To set the scene, let us look back at the situation which has existed in our industry in the past.

Jan 1, 1993

By M. C. van Blerck

This paper outlines the tax provisions that became defective in January 1992, which allow a working mine to make tax-deductible contributions to a dedicated environmental body that is itself not subject to tax. Such a body will then provide a source of funding for the mine's future environmental expenditures. It is concluded that the establishment of such environmental bodies is a financially sound, tax-effective route, allowing mines, prospectors, and quarry operators to provide for future environmental rehabilitation.

Jan 1, 1994

By J. P. Coetzee

There is an ample supply of all the raw materials required for the future development of the industry, with the possible exception of coking coal. Improved methods of coke production are being developed. It is anticipated that steel production will reach eight million tons per annum by 1980. New techniques and equipment for refining steel will be installed, together with new processing equipment. The most serious problem now facing the industry is the acute shortage of labour.

By D. W. Horsfallt

The above paper gives a fair amount of information and is a useful addition to the literature on a subject of growing importance. I believe that more experimental results could have been given, together with more details of the modifications made to the plant that enabled it to operate with the success mentioned in the paper. One important omission is a definition of the word fines. As pointed out elsewhere!, this word is used very loosely.

Jan 1, 1980

By N. B. Strydom, H. H. E. Schroder, A. van der Linde

This paper describes a study of the destination of the mercury that is present in the ore during the recovery of gold. It was found that over 96 per cent of the mercury passed through the process untouched. A small amount finds its way into cyanide solution, and is concentrated with gold in Zinc dust as Merrill precipitate. When the precipitate is calcined, the mercury is driven off and finds its way into the atmosphere. However, dilution of the stack gas in the atmosphere appears to be sufficient to prevent hazardous concentrations arising at ground level. No other significant concentrations of mercury were found at any stage of the process. The amount of mercury lost to the atmosphere by this mechanism appears to be less than 200 kg per year throughout the gold-mining industry in South Africa. Virtually no mercury vapour could be detected in the air in the smelt-house. Slight increases in mercury concentrations above background level were observed in soils around the reduction plants and in the discharge or return waters, but no environmental stress is anticipated from these increases.

Jan 1, 1982

By A. S. Macfarlane

"SynopsisMetal accounting and reconciliation is an increasingly important governance issue in all mining operations, in that it is required, from a risk management perspective, that the company is in control of its product throughout the whole mining value chain. Reconciliation is a grossly misunderstood term. It means different things to different people, and therefore one of the purposes of this paper is to ensure a holistic and integrated understanding of ‘reconciliation’.Previously, where reconciliation was done, it was often for internal control purposes and loosely applied, sometimes with a low degree of confidence and understanding of the underlying parameters and their natural variability.In most mining operations, issues such as dilution, stope performance, and recovery are critical to profitability and long-term value, and thus understanding and control of these key value drivers is essential, not only from the governance perspective, but also from the perspective of maximizing shareholder returns. In order to implement a system for metal accounting and reconciliation, it is important that the cause and effect of these value drivers is understood, and that a systematic control system be established.While a number of off-the-shelf solutions exist for this work, it is the contention of this paper that a full understanding of the metal flow, its variability, its underlying loss potential, and its control points is necessary before a systematic approach to reconciliation can be undertaken.The paper also advocates that this approach should ensure that the reconciliation system clearly addresses the reconciliation needs, within a consistent framework. Such a framework has been developed by AMIRA, in terms of a metal accounting code. However, up until now, this code has been aimed at plant processes, whereas this paper shows how the concept can be extended to cover the full reconciliation requirements for a base metal mine.IntroductionReconciliation is defined as ‘the process of finding a way to make two different ideas, facts, etc., exist or be true at the same time’. In terms of a mining process, this refers to the comparison of measures and estimates along the value chain, and at different points in time, in order to track and optimize metal recovery. This leads to the notion of having a system in place for accounting for the metal. The University of Cape Town defines metal accounting as ‘… the estimation of (saleable) metal in a mine and subsequent process streams over a defined time period. Comparisons of estimates, from different sources over a specific time period, are called reconciliation.’Traditionally, metal accounting has consisted of geological reconciliations of mineral resource to mineral reserve conversion, mine planning reconciliation related to the reconciliation of long-term plans to short-term plans, grade control reconciliation of head grades to sampled or block grades, and mine survey reconciliation of tonnage discrepancies and mine call factors. In addition, metallurgical reconciliation has tended to be based on metal balancing, followed by some commercial metal accounting that links dispatched product to sales quality, quantities, and revenues. Miners disparagingly refer to this plant process as ‘millmatics’."

Jan 1, 2015

By R. P. King

Held on the 22nd March 1972 at Kelvin House. Four papers were presented at this colloquium, which was attended by approximately 120 people. The first paper, 'Flotation Research Work at the N.I.M. research group, University of Natal on the modelling of a Flotation Process' was presented by Dr R. P. King, the leader of the N.I.M. Research Group in the Department of Chemical Engineering at the University of Natal. A discussion panel, under the chairmanship of Dr R. E. Robinson with Mr M. Dawson (PMC), Mr E. Roux (FOSKOR), and Dr B. K. Loveday (NIM), discussed the potential application of the theoretical work on flotation modelling to industrial processes, and alternative approaches to providing a way of control of flotation plants. The second paper, 'Fundamental Studies of the Flotation Process the Work of the National Institute) for Metallurgy', was presented by Dr N. P. Finkelstein. The discussion panel for this paper was under the chairmanship of Professor D. D. Howat,and had as its members Mr H. P. Carlisle (JCI), Professor D. le Roux (University of Pretoria), and Mr E. Rudolph (Anglo American Research Laboratories). A lively discussion on this paper ensued, with several contributions from the floor. After lunch, Mr S. K. de Kok, Assistant Consulting Metallurgist, Anglo Vaal, presented a paper on 'The Flotation of Copper and Zinc Sulphide from Prieska Ore'. The paper was discussed by a panel comprising Dr V. C. Lovell (NIM), Mr A. Gilbert (General Mining), and Dr D. Legge (Anglo Vaal), under the chairmanship of Dr L. Bushell. This discussion, in which many members of the audience participated, revolved around the difficulties associated with the production of copper and zinc concentrates and the lack of fundamental information on the behaviour of copper and zinc sulphides in flotation. The final presentati0n was a paper, 'The Recovery by Flotation of Cassiterite contained in Gravity Concentration Plant Tailings', presented by Mr E. B. Viljoen (Metallurgy Department, Goldfields South Africa Limited). The discussion, led by a panel consisting of Mr O. Tant (Goldfields Laboratories), Mr J. Levin (NIM), and Mr R. I. Shanks (NIM), under the chairmanship of Mr H. Cross (Goldfields South Africa Limited) referred particularly to the use of new reagents for the flotation of tin, with particular emphasis on the fundamental relationship between reagent composition and its ability to float this type of mineral.

Jan 4, 1972

By J. E. Quintanilha de Menezes, L. Ribeiro e Sousa, I. Ferreira

The Paradela dam has a spillway that makes it possible to discharge a maximum flow of 400 m3/s, the water discharges being on the river Sela, about 2km upstream the river Cávado. After the first use of the spillway, some landslides have occurred on the right bank of the river Sela as a result of the erosion generated on its base about one hundred meters near some houses of a small village. This paper presents a study performed for the slope stability where finite element results are taken into account. A monitoring program was established that essentially consisted of measuring sub-horizontal displacements in points located in boreholes at different depths and also phreatic levels. Some monitoring results are presented. Le barrage de Paradela a une décharge d’eau avec un débit maximal de 400 m3/s sur le fleuve Sela dans un endroit situé environ 2km sur l'amont du fleuve Cávado. Après la première utilisation de cette décharge, quelques glissements se sont vérifiés sur le versant droit du fleuve Sela résultant de l’érosion générée sur sa base dans une zone à 100 mètres de quelques maisons d’un petit village. Ce travail présente une étude réalisée concernant la stabilité du versant avec la considération des résultats des éléments finis. Un programme d’auscultation a été mis en place pour mesurer les déplacements sub-horizontales sur des points situés en forages à des différentes profondeurs. Quelques résultats de cette monitorization sont présentés. Der Ueberlauf des Padela Dammes ermoeglicht das Ablassen einer max. Wassermenge on 400 m3/s in den Sela Fluss, ca. 2 km flussaufwaerts des Cávado Flusses. Nach Inbetriebnahme des Ueberlaufes traten in ca. hundert Meter Entfernung zur Wohnbebauung eine Dorfes Erdrutschungen am rechten Ufer des Sela Flusses auf, die auf Erosionen am Flussbett zurückzuführen waren. In der vorliegenden Studie wurde die Boeschungsstabilitaet unter Beruecksichtigung von Berechnungsergebnissen der Finiten Element Methode untersucht. Es wurde ein essprogramm ausgearbeiten, das im Wesentlichen auf Messungen der Untergrundverformungen in verschiedenen Bohrlochteufen sowie auf Grundwassermessungen beruht. Im Folgenden sind einige Messergebnisse dargestellt.

Jan 1, 2003

In the investigation described here, it was found that the main effect of temperature is on the rate of flotation, and that adsorption of the reagent is not rate controlling. Above 10°C, the flotation rate of pyrite and gangue increases almost exponentially with a rise in temperature. Below that temperature, the flotation rate of pyrite shows a sudden marked decrease, that of gangue increases, and the sulphur grades are significantly poorer. In the flotation of pyrite, the mass transfer of the pyrite from the pulp to the troth is thought to be the ratecontrolling step, whereas the flotation of gangue is controlled by the combined effect of the stability and velocity of the froth and the viscosity of the elutriating medium. The latter is probably the controlling effect at temperatures below 10°C. Little difference was noted in the recoveries (provided no time limit was set) with changes in temperature; hence adequate recoveries can be obtained at Iow temperatures by the introduction of longer residence times for the pulp. The adverse effects of Iow temperatures on grades can be overcome only by additional cleaning or by heating of the pulp.

Jan 1, 1984

By A. García-Gutiérrez, A. Aragón-Jerónimo, R. Salazar-Mendoza

A theoretical analysis of a two-region solid-liquid flow system in horizontal pipes is presented, which considers a stationary bed of drill cuttings as a porous medium (-region) below of a two-phase dispersed flow (-region).The method of volume averaging was applied in this study to derive a rigorous mathematical model in which each variable is precisely defined. This model includes the volume-averaged transport equations for both the two-phase dispersed flow and the porous medium regions and terms from a macroscopic forces balance. The solution of the two-region model allowed evaluation of the behaviour of pressure gradient as a function of velocity, total volume fraction of cuttings and the relationship of the height of the stationary bed and pipe diameter. The solution is based on a backward finite difference explicit scheme. The simulated physical system is a pipe of 4.135 m in horizontal length and 0.0508 m in diameter. A one-dimensional, mesh-centred grid, consisting of 100 nodes, is used. The numerical results were compared with experimental data on slurry flows and a good agreement was found. Keywords: two-phase, cuttings transport, solid-liquid flow, drilling modelling, volume averaging.

Jan 1, 2007

By A. Dabbagh

The aim of this research was to investigate the effect of coke particle size on the thermal profile of the charge bed in the sintering process of iron ore. Six different ranges of coke particle size that could be used in practice in the sintering line of Esfahan Steel Company (ESCO) were used while parameters such as ratios and particle sizes of other ingredients, ignition temperature, and suction power were kept constant. Thermal profiles were obtained by measuring the temperature changes at three points in the sintering bed. The influence of coke particle size on rate of temperature rise, maximum temperature of the sintering bed, and the flame front velocity of the sintering bed was determined by analysing the thermal profiles. Moreover, the cold strengths of the sinters were measured using the Tumbler method. The results indicated that the coke particle size has a significant impact on the thermal properties of the sintering bed. Based on the results, a coke particle size between 0.212 mm and 3.350 mm was determined as the optimal range for the specific conditions in the sintering line of ESCO. Keywords iron ore sintering, coke particle size, thermal profile, flame front velocity, Tumbler index.

Dec 1, 2013

By Milton Syamujulu

In 1994, Nkana smelter commissioned a Multimillion US$ Dollar Chilean Teniente converter (CT) in its operations in order to improve its smelting technological base. The main objective was to reduce the overall smelting energy costs and increase the sulfur capture for sulphuric acid production to support the company?s leaching operations at Nchanga Tailings Leach Plant. A decade of CT operations have since ensured following its installation and startup. This paper provides a Technical and Operational Audit of the performance of the CT in the first 10 years of its operations at Nkana smelter.

Jan 1, 2005

By A. Cambitsis

We show that the prioritization of business improvement and performance management decisions may be significantly improved by taking into account the systemic effects of changes made in a single process area. To do so we build a model of a mining value chain, taking into account consequential downtime that arises from downstream and upstream starvation and choking effects of each activity. Introducing the concept of internal capacity, this approach yields insight into the relative importance of key metrics such as loading and hauling rates. We suggest that a holistic view of this type should be a core component of business improvement and performance management decisions. Keywords value driver trees, production constraints, throughput analysis, capacity analysis, TOC (Theory of Constraints), activity interdependencies, unit cost reduction.

Oct 1, 2013

By André Fouché

GFWW Bulk Sample Prep Plant INDEX ?Features ?Flow Diagram ?Pictures of Plant

Jan 1, 2005

By F. Trabzuni

Elutriation of solid reactants from fluidized bed reactors can affect their process performance and efficiency greatly. Chlorination fluidized bed reactors for selective conversion of solid metal oxides to metal chlorides are used widely these days. This study provides a platform for a proper understanding of reactant solid characteristics and solid shrinkage interaction with elutriation rate constants using multi-sized particles, sand-like, ?Geldart B? chloridable materials. The study has found that actual elutriation rates of the reactive system are influenced by complex parameters? interaction including bed diameter, reactor freeboard height, bed minimum fluidization velocity, and reactant?s physical properties.

Jan 1, 2009

By G. W. Holl, E. G. Fairon

A review of some aspects of shaft design by G. W. HOLL, Pr. Eng., Associate of the Mine Managers Association of South Africa (Fellow)- and E. G. FAIRON, Pr. Eng., F.S.A.I.E.E., M.I. Cert. M.E.E., M.I.Mech. E., (Visitor) The reasons for the choice of vertical shafts in preference to inclined shafts of comparable capacity are set out, and the conclusion that the former are superior in virtually all circumstances is substantiated. The shapes of vertical shafts sunk during the past sixty years are recorded, and the shapes of those sunk during the past decade are analysed. From this analysis it is clear that circular and elliptical (and quasi-elliptical) shafts are the shafts of the future and that the rectangular shape will conceivably become obsolete. The determination of the size of shaft is discussed and it is forecast that shafts of a diameter of 13 metres and over will probably be sunk without difficulty in the years to come. The depth of the shaft is determined intrinsically by the Mines and Works Regulations applicable to factors pf safety of winding ropes and the design of the winding system. The Blair winder is the most suitable winder for hoisting rock, men, and material from a depth of, say, 3000 metres on an economic basis. Tertiary shafts will, therefore, be unnecessary in future deep-level mining projects at the limit of depth now envisaged. A few other factors relating to shaft design are described.

By P. R. Jochens, D. D. Howat, A. A. Hejja

The effect of the reactivity of lime on desulphurization efficiency in the basic oxygen furnace A. A. HEJJA, Dipl. Ing. (Budapest) (Visitor) D. D. HOWAT, B.Sc. (Glas.), Ph. D., F.I.M. (Fellow) P. R. JOCHENS, Pr.Eng., M.Sc. (Eng.) Rand, Ph.D., A.I.M. (Member) The iron charged to the basic oxygen furnace at the steel plant of Highveld Steel and Vanadium Corporation has a relatively high sulphur content. Considerable emphasis is therefore placed on the reactivity of the lime. An investigation of the lime used at the steel plant showed that its reactivity had deteriorated considerably both during transport from the supplier (Northern Lime Company) and during storage and handling at the steel plant. The deterioration on the steel plant is the more severe, and is due to hydration and carbonation. Rapid deterioration is a characteristic of highly reactive lime when exposed to the atmosphere. Plant tests showed that the desulphurization efficiency decreases with a decrease in the reactivity of the lime. The addition of slag rich in manganous oxide to the furnace considerably improved the efficiency of desulphurization that can be achieved with limes of lower reactivity and with lime that has deteriorated. A decrease in particle size of lime of lower reactivity greatly increased the desulphurization efficiency. Less lime of higher reactivity is required for the same degree of desulphurization to be achieved. Lime of higher reactivity gives rise to slags with lower ferrous oxide contents and hence the steel yield is increased.