Search Documents

By H. Wagner

The paper points out that bord-and-pillar mining is the most important method of coal extraction in South African underground coal mines, and advocates that pillar design procedures should be refined to make more rational allowance for the differences in strength properties between various coal seams and roof and floor strata. However, any deviations from well-established design procedures must be based on sound engineering principles and reliable data on the strength properties of the seams and strata concerned. Recent information indicates that practices for the protection of surface structures against underground mining should be revised.

Jan 1, 1980

By B. B. Mamba, J Ndalamo

The existence of an impressive reserve of oxidized cobalt-copper bearing ores in the African copper belt area lead the GECAMINES (DRC) to develop specific and adapted mineral processing routes (Mulaba-Bafubiandi, 2001). During the conventional diluted sulphuric acid leaching of oxidized cobalt-copper bearing ores commonly referred to as ?heterogenite?, more than 10% cobalt dissolution yield increase was observed in a plant situation (Mwema et al., 2002) when SO2(g) was flushed into the acidified cobalt leaching solution. The present paper attempts to elucidate mechanisms involved which lead to the increase of total cobalt as SO2 is flushed during the leaching of oxidized cobalt bearing minerals. The kinetics of cobalt dissolution as SO2 is flushed into the acidic solution as well as a full characterization, using UV-Visible spectroscopy, of Co2+ and Co3+ species present in the collected leachate are presented while possible effects of the presence of Cu and Fe on the leachability of cobalt bearing minerals present in the oxidised ore will be discussed. In the view of speeding up the leaching process, the mixed cobalt-copper oxidised ores were microwaves pre-processed. Preliminary results were also discussed.

Jan 1, 2007

By A. L. Hinde, P. J. D. Lloyd, D. Hebden

The philosophy behind the design of a rougher cell for the handling of coarse feed and for the maximization of recovery within a given time is presented. The application of this philosophy in cells of 22-litre, 320-litre, and 3 m3 capacity is outlined, and the results of the process testing of these cells are given. In this testing, particular accent was placed on the recovery of water as a guide to the recovery of the finest size of particles, and the rate of recovery of various mineral species. It is concluded that a promising concept has been identified, but that further testing is needed for the firmer establishment of optimal operational parameters in a production environment.

Jan 1, 1983

By R. S. Sanders, J. Schaan

Syncrude Canada Ltd. produces synthetic crude oil from Canada?s vast oil sand reserves by mining the oil sand, then separating and upgrading the ultra-viscous crude oil, or bitumen (~ 106mPa s @ 10ºC). At Syncrude?s Aurora Mine, about 16 000 tonnes oil sand per hour are mined and then transported 5 km by slurry pipeline to the extraction plant. The waste tailings stream is then transported about10 km by pipeline to a settling/sand storage basin. Oil sand slurries are reasonably concentrated (> 35%solids by volume), typically have a sand particle diameter between 0.18 and 0.3 mm, and are transported at reasonably high velocities (3 to 5.5 m/s). As one would expect, pipeline wear is a significant problem in this industry, in terms of both unplanned production outages and maintenance costs. In order to develop strategies to extend pipe life and to focus more on condition-based maintenance scheduling (as opposed to preventative maintenance), Syncrude has implemented an ongoing pipe wear measurement programme. Regular measurements of pipe wall thickness are obtained at various circumferential positions at a number of axial locations along each pipeline, using an ultrasonic scanning technique. In this paper, we show how wear rates vary as a function of axial location and circumferential position for oil sand hydro transport and coarse particle tailings pipelines. The specific positions at which peak wear rates occur are explained by considering the characteristics of the coarse particle slurry flows to which the pipelines are exposed.

Jan 1, 2007

By D. Duncanson, R. J. Davidson

The elution of gold from activated carbon using deionized water by R. J. DAVIDSON, M.Sc., Ph.D. (Rhodes) (Visitor) and D. DUNCANSON, H.N.C., B.Sc. Hons. (Strathclyde) (Visitor) The pretreatment of gold-loaded activated carbon with a relatively strong sodium cyanide solution prior to elution with deionized water at 90 to 125°Chas been shown to have a most beneficial effect on the elution of gold. The findings emphasize the important role played by the calcium cation and the hydroxyl anion in effecting efficient elution of gold. The elution of the relatively unstable complexes of silver and base metals with cyanide was also significantly affected by the ratio of the sodium cyanide to sodium hydroxide in the reagents used in the pretreatment stage. It was demonstrated that the use of 0,5 bed volume of a pretreatment reagent comprising 10 per cent sodium cyanide stabilized with I per cent sodium hydroxide for safety reasons resulted in a virtually 100 per cent recovery of adsorbed gold, silver, and base metals on subsequent elution with deionized water. The elution procedure takes a relatively short time, about 14 hours at 90°C (7 bed volumes) or 3 hours if pressure elution at 125°C (4 to 5 bed volumes) is used. Because the mechanism of elution after pretreatment entails the shifting of a physical rather than a chemical equilibrium, the higher the gold loading on the activated carbon, the more efficient is the elution procedure. When compared with other elution procedures, the proposed method appears to have several economic advantages.

Jan 7, 1977

By S. Carter

this paper describes an innovation in computer software that permits mining professionals to collaborate on exploration and mining projects regardless of geographic location. Growth of mining companies through merger and acquisition has created a greater need for mining professionals to collaborate, especially as projects and project participants are becoming geographically remote. Surpac NetVision, the name given to this new collaboration technology, satisfies this need by deploying interactive 3D graphics sessions across computer networks. It achieves this by using common web browser technology as the deployment medium. A plug-in architecture that supports diverse file formats permits transparent read and write of foreign data to further enhance the collaboration process. Surpac NetVision supports any number of connections from web browsers on remote computers using existing networks. Software components required to enable the collaboration session are deployed to the remote computer as required and cached for future sessions. The collaboration session at each computer is characterized by a fully functional replica of the user interface for Surpac NetVision from which any function can be executed by any client, at the owners discretion. All geometry and display attributes deployed to remote clients to render 3Dgraphics are highly compressed to reduce bandwidth requirements. The key benefits of this collaboration technology is improved communication in regard to exploration and mining projects leading to: •More informed decision making •Improved deployment of project objectives and plans beyond the technical planning group to project management and operations staff •Improved technical support for software users. Keywords: 3D graphics, project collaboration, interactive graphics, internet 3D graphics, mining software

Jan 1, 2003

By I. E. Teymenson, N Fedunets

Mining-metallurgical complex is the base of any economics and influences directly on practically all branches of world economics. Therefore the task of estimation and selection of investment decisions in mining industry adequate to modern market conditions and the task of decreasing multidimensional alternatives selection uncertainty are very actual. An uncertainty of investment alternatives is explained by a number of reasons, main of which are a presence of several investors types, an unstable situation on the market and an absence of evident relations between appraisal criteria used. Maximum increasing of formalization and objectivity of information technologies applied for an estimation permits to reduce the uncertainty of investment variants estimation. A number of principled innovations, allowing to solve the task of decreasing of multidimensional alternatives selection uncertainty, are introduced into the information technology of estimating and selecting investment decisions in mining-metallurgical branch, developed by us. In the article the necessity of including a cognitive model into developed selection mechanism, which allows to take into consideration inter-influences of used critera, has been grounded. Besides, the forecasting model considering interconnected time rows has been applied for increasing the world conjuncture forecast quality. Further in the article main metrics types have been characterized and application of weighted Chebyshev’s metrics as the most compromised from all studied metrics for variants selecting has been proved, and also the developed procedure of directional search of effective compromise decisions has been described. Brief characteristic of designed instrumental means of multi-criteria variants estimation and selection finalizes the article. In conclusion expedience and efficiency of using the developed information technology for reduction of multidimensional alternatives selection uncertainty have been grounded.

Jan 1, 2003

By G. Newson, N. Runciman

In 1999, INCO Limited Mines Research, in Sudbury, Ontario, Canada, took delivery of a MeycoRobojet Logica Spraymobile, a computerized concrete spraying system. The Spraymobile is a self-contained mobile machine capable of applying spray-on ground support in underground applications. The Logica component of the Robojet is designed to control the operation of the Robojet, as well as scan and map the tunnel geometry prior to the spraying operation. The Robojet can be operated in various modes, from manual to automatic operation. In the automatic mode the computer controls the standoff distance, angle, and motion of the spraying jet. In 2000, INCO Limited, working with Meyco Equipment of Switzerland (a division of MasterBuilders Technologies), detailed a plan to create a tele-operation package for controlling the spraying process from a surface location at INCO's Mines Research Test mine. With the RobojetLogica operating in automatic mode, the operator at the machine becomes a process monitor. Since the Logica system controls the key spraying parameters of nozzle distance and nozzle angle to the sprayed surface, the operator could easily monitor and control the Robojet Logica from aremote location. The benefits of operating underground mobile mining (drills and LHDs)equipment from a surface location has been demonstrated at INCO Limited, however, the abilityto control a ground support operation (shotcrete spraying) from surface has not been attempted until now. This paper will describe the Spraymobile shotcreting system, the development of the tele-operation package for the Robojet Logica, as well as modifications to the original Spraymobile for implementing the tele-remote package on the Robojet Logica at the Mines Research test mine.

Sep 1, 2001

By P. J. Petit

The strategic mission of the South African mining industry is to extract the mineral assets in an energy efficient, economical and safe manner. Drilling has received particular attention in the last few years. As the operations move away from the power source, conventional and old drilling technology result in poor penetration rates, increased drilling shift lengths, slow face advances and limited stope efficiencies. The need for an alternate mining method, performed by a skilled workforce, to increase productivity, has led to the development of the electric rock drilling system for in-stope mining operations. The focus of this paper is a systematic evaluation of the electric rock drilling system as a function of production and technical parameters, in the platinum orebody. The particular electrical reticulation system is illustrated. Power usage, problems experienced, and solutions are described. The safe use of the recently developed drill is elaborated upon by describing protection devices. The testing and certification process, for approval by the recognized authorities, are documented. The testing and certification process, for approval by the recognized authorities, are documented. The human factor is also considered. Known detrimental factors of high noise exposure, vibrations levels and oil emissions are reviewed. In conclusion, recommendations on future strategies for the implementation of electric drilling technology within the mining and construction industries, is included.

Jan 1, 2006

By R. G. B. Pickering

Conventional mining is an excellent match of mining method and equipment. The result is guaranteed performance. Change in the form of different technology requires change in mining method until the best match is achieved. This paper covers the development of technology and mining method that has occurred in the last five years to arrive at the objective of successful mechanized mining in narrow reef platinum deposits of the Bushveld Complex.

Jan 1, 2004

By M. Pelser, J. Hagemann

"The Anglo American Platinum Rustenburg Base Metals Refiners (RBMR) is the largest producer of nickel cathode in South Africa. It treats slow-cooled matte to recover a platinum group metal-containing magnetic fraction for downstream processing and a nonmagnetic fraction to produce nickel and copper cathode, cobalt sulphate, and sodium sulphate. The refinery was recently expanded from 21 to 33 kt/a nickel. During the ramp-up phase, the sulphur removal section was found to be a constraint to throughput. Nickel hydroxide is precipitated from nickel spent electrolyte by addition of sodium hydroxide, and filtration of the nickel precipitate allows sulphur to be removed from the circuit as aqueous sodium sulphate in the filtrate. The filtration fluxes were found to be limiting the circuit’s capacity. An obvious solution would have been to install additional filtration capacity at significant capital cost and long lead times. RBMR chose rather to first initiate a collaborative project with Anglo American Technical Solutions to better understand the impact of process conditions on filtration characteristics and to evaluate whether the filtration flux could be increased by improving the quality of the nickel precipitate.A deeper understanding of nickel hydroxide precipitation chemistry and kinetics in the context of high nickel and sodium hydroxide concentrations was developed, guided by precipitation theory and confirmed by laboratory tests and plant observations. It was found that the filtration rate could be significantly improved by modifying the precipitate characteristics. A new precipitation process was engineered and retrofitted into the existing plant. Since start-up of the new precipitation system, the available capacity of the sulphur removal section has more than doubled, and control of the process has improved with the better agitation. This paper describes the theory and results used to design the new agitation system, as well as the impact of the change on capital investment, operability, and process efficiency."

Jan 1, 2016

By J. C. M. De Souza

The Samarco pipeline, the longest in the world for iron ore slurry transportation, started operation in 1977 to transport concentrate from the Germano facilities, in the state of Minas Gerais, to the pelletizing plant, located 396 km away, in the state of Espirito Santo, on the south-east coast of Brazil. Designed for a nominal capacity of 12 million tons per year, the pipeline reached 15.5 million/year due to operational improvement and, in late 2005, it was resized to transport 16.5 million tons per year, with the installation of a booster station. In order to ensure the accurate performance of the system, a pipeline cleaning programme was carried out and, since it has been29 years from the operation start-up, precise knowledge of the pipe condition would be fundamental to guarantee the success of the project. The cleaning programme demonstrated the potential of operational gains from this initiative, and its effect on the corrosion control and future measures, which should be permanently adopted to maintain the improved capacity. The intelligent pig runs provided essential data used to establish a pipeline integrity programme that allowed Samarco to develop a pipe repair plan based on the severity and significance of the features and to implement a future pipe replacement plan.

Jan 1, 2007

By J. van der Walt, A. Whillier

Reference is made to the approach to mine cooling in which the service water is used as one of the means of distributing refrigeration, and attention is drawn to various engineering disciplines or functions necessary for effective distribution and reticulation of cold water from refrigeration plant. The demand for service water is intermittent, the peak flow-rates being typically two to three times the average flowrate. The refrigeration plant, on the other hand, must preferably be operated steadily throughout the day and night, with the result that a large storage dam for cold water must be incorporated into each system in order to even out the surge in demand for water. These dams should be operated as constant-temperature, variable-volume reservoirs. The conventional cascade system involving dams on each level is not the best for sending water down mines, and schemes are described that avoid the need for such dams. Reference is made to various tests that were carried out, and to several large systems that were installed. Management and organizational problems that could arise as a result of new technological developments in mine cooling are referred to, and cost figures are quoted to indicate the large potential savings, In addition to the improved environmental conditions, that can be achieved through the use of integrated water systems.

Jan 1, 1979

By A. L. Edwards

A retrospective study was conducted on the Rand Mutual Assurance (RMA) noise-induced hearing loss (NIHL) compensation claims from 1998 to 2008 to determine if the 2008 milestone agreed at the 2003 Mine Health and Safety Summit was achieved. The number and costs of NIHL compensation claims in different commodity sectors and workplaces were collated. A secondary analysis of the ages of employees compensated after 2008 was conducted. A complementary retrospective analysis of audiogram data investigated the percentage loss of hearing (PLH) shift in different homogeneously exposed groups and occupations at two gold mines. The compensation claims analysis indicated a significant decrease in NIHL claims from 1998 to 2008, but the milestone was not achieved. The reason may be either that claims have not been submitted timeously as required by Instruction 171 and that the current submissions are a result of pre-2003 noise exposure, or that employees who were baselined are still developing NIHL owing to ineffective hearing conservation programmes in place in the mining industry. On the basis of best practice for hearing conservation, recommendations are made for leading indicators in hearing conservation programmes and for reducing the risks of NIHL in order to achieve the 2013 milestone.

Jan 1, 2012

By H. A. D. Kirsten

The skills differential between manpower supply and demand is due to deeply rooted socio- and politico-educational misconceptions that can be remedied only by a concerted cooperative effort on the part of the general public, the State, organized industry, organized engineering, and engineering education. This will require the general public to recognize that the reasons for the shortages in engineering manpower should be regarded as critical. Public perceptions of engineering, of the vocational and educational prospects in engineering, and of the skills required are poor. The spectrum of engineering vocations, the corresponding function profiles, the interaction between the vocations and the relative proportions of the vocations in the engineering team are in general not adequately appreciated. The recruitment and training of students and teaching staff, teaching facilities, educational curricula, practical training, qualifications, professional registration, and financing are aspects of engineering education that should be brought to the attention of all concerned. . In addition, the educational curricula for the various vocations need to be specified clearly and definitively if the overall mission of engineering education is to be properly appreciated. The uncertainties between university and technikon education and the pursuant vocations need to be resolved. This can be done only by defining the respective curricula in terms of the mental skills and scientific techniques required. The remedial actions with regard to the rationalization of engineering education comprise informing of the public; establishment of an active political lobby; revision of existing education policy; rationalization of existing educational infrastructure; promotion, development, and guidance of engineering student intake; financing of engineering education; accelerated creation of new employment opportunities; and monitoring of the supply and demand of high-level manpower. The parties required to nitiate these remedial actions are various State departments and corporations involved in engineering and industry, various departments of education, the Directorate of Technology of the Department of Trade and Industry, organized engineering education, organized engineering, organized industry, and the Human Sciences Research Council. Only if these interest groups actively initiate the various actions under the coordinated guidance of organized engineering wil the required results be achieved. The South African Engineering Association has proposed a comprehensive programme as strategy to solving the problem, and has obtained broad consensus from various State departments, organized engineering education and research, and the private sector. A joint venture between the Foundation for Research Development, the South African Engineering Association, and organized industry has been charged by the State President with the task of launching the programme.

Jan 1, 1991

By J. H. Lazarus

The evolution of backfill-distribution systems for deep gold mines is examined. The status of current technology for the design of backfill-distribution systems is considered with reference to pipeline pressure gradients, pipeline wear rates, and slurry flow regimes. The effect of an increase in the relative density of the slurry on the performance of backfill-distribution systems is illustrated. Future trends regarding the design of backfill-distribution systems are discussed.

Jan 1, 1993

By R. Heunis

The hazard of rock bursts and rock falls as experienced in South African gold mines is examined in the light of recent research findings. The problem areas include high fatality rates, losses in production and equipment, and a detrimental influence on the recruitment of labour. The nature of the hazard is analysed, and it is shown that rock bursts are strongly related to the spatial rate of energy release by mining but that rock falls are not. The role of blasting and geological discontinuities is discussed. Practical rock-burst control strategies are compared, including the use of stabilizing pillars, back-filling and, in particular, techniques for reducing the frequency and severity of accidents resulting from large rock bursts. The latest stope-support experiments and their potential implications to mining are consid~red. It is concluded that a better understanding of the rock-burst and rock-fall hazard has resulted from the industry's research efforts. The findings can be applied towards obtaining an improved underground environment for men and machines.

Jan 1, 1980

By M. C. van Blerck

Since its introduction in 1956, the capital allowance has been increased and its scope widened. At present the allowance is 10% in respect of two categories of gold mine (post-1973 and other deep level mines) and 6% in respect of natural oil mines. The allowance is a significant incentive encouraging the development of new mines, to the benefit of both the fiscus and the South African economy as a whole. A strong case can be made for increasing the amount and the scope of the allowance. The Margo Report recommendation that the allowance should possibly be replaced with a system of direct grants is, in theory, neutral. However, practical difficulties exist with cash grants and there is concern with the implications elsewhere in the Margo Report that the capital allowance is excessive and that, as a consequence, such direct grants will represent an effective reduction in this incentive. I believe that the best course of action would be the retention (and enhancement) of the capital allowance and the expansion of its scope.

Jan 1, 1988

This paper illustrates the application of numerical modeling methods, in conjunction with limit-equilibrium techniques, to the location of critical slip surfaces in slope-stability problems. Initially, the Spencer slice-based method of analysis is introduced, together with a dynamic-programming algorithm for slip-surface location. This limit-equilibrium method is assessed critically through the use of an illustrative problem. The technique is then extended to locate the critical slip surface for a similar slope, but with more complex constitutive and yield relationships for the material comprising the slope. To this end, the use of the stress field generated from a finite-difference program, together with a dynamic-programming search routine, is presented as an advanced technique of slope-stability analysis for engineers.

Jan 1, 1993

By W. Lin, H. Endo, M. Kwasniewski, A. Kamei, M. Takahashi

Uniaxial tension tests were conducted on specimens of eleven granitic rocks which came from eastern Japan, and included a granite, four granodiorites, four tonalites and two gabbros. The axial and transversal deformability of these rocks was determined based on strain measurements using wire strain gauges. The experimental test results revealed that deformational properties of the rocks investigated varied depending on their petrographic features. However, the axial strain and the lateral strain characteristics showed a similar trend for all the rocks, i.e. the stress-strain curves were non-linear throughout the whole stress range from the initial point of loading to the point of ultimate failure. Moreover, the tangent Young's modulus and the ratio of the lateral strain to the axial strain decreased monotonously with the increasing of the axial stress. Still, the deformational properties were different for individual rocks in a quantitative sense. In particular, the difference in the lateral strains among different rocks was more distinct than that in the axial strains. For example, the Poisson's ratio at a stress level equal to 50% of the ultimate strength of a granodiorite was very low, close to zero. Furthermore, the Poisson's ratio of a tonalite was lower than that of a granodiorite, and assumed a negative value. This effect occurred because the lateral strain became positive as it changed from contraction at the initial stage of loading to extension at higher stress levels. There is no ready explanation for this phenomenon; it is believed, however, that it occurs due to microcracks pre-existing in rock materials and/or weak bonds between the adjacent mineral grains. Les essais de traction directe ont été conduits sur les échantillons de onze roches granitiques provenant de la région Est du Japon: un granit, quatre granodiorites, quatre tonalites et deux gabbros. Déformabilité axiale et transversale de ces roches s’était déterminée en utilisant des jauges extensométriques à fil. Les résultats obtenus à partir des essais montrent que la déformabilité des roches examinées varie selon leurs propriétés pétrographiques. Cependant, à partir des essais, une tendance semblable était observée dans les paramètres de la déformation axiale et la déformation latérale de toutes les roches; c'est-à-dire chaque courbe de contrainte-déformation était non-linéaire dans tout l'intervalle de contraintes à partir de l’état initial jusqu’à l’état d’une rupture finale au cours du chargement. De plus, le module tangent de Young et le rapport de la déformation latérale sur la déformation axiale a diminué de manière monotone avec l'augmentation de la contrainte axiale. Cependant, les différences quantitatives de propriétés de déformation sous traction étaient observées entre des roches individuelles. Particulièrement, la différence de déformations latérales était plus notable que celle-là de déformations axiales entre des roches différentes. Par exemple, le coéfficient de Poisson à un niveau de contrainte égal à 50 % de la résistance d'un granodiorite était très bas, près du zéro. En outre, le coéfficient de Poisson de la tonalite était inférieur que celui du granodiorite et a assumé une valeur négative. Cet effet est apporté parce que la déformation latérale est devenue positive en passant de la contraction dans l'étape de chargement initiale à l'extension sous les contraines plus hautes. Il n'y a aucune explication prête de ce phénomène; on prétend, cependant, qu'il est induit par des microfissures préexistantes dans des matériaux rocheux et/ou des joints faibles entre les grains minéraux adjacents. Einaxiale Zugversuche wurden auf Probestuecke von elf frischen, in Ostjapan vorkommenden, granitartigen Gesteinen durchgefuehrt, welche einen Granit, vier Granodiorite, vier Tonalite und zwei Gabbros umfassten. Die axiale und transversale Verformbarkeit von diesen Gesteinen wurde durch Verformungsmessungen mit Drahtdehnungsmessstreifen geklaert. Die experimentellen Versuchsergebnisse offenbarten, dass Verformbarkeitseigenschaften des untersuchten Gesteins in Abhaengigkeit von ihren petrographischen Eigenschaften variierten. Jedoch zeigten die axialen und die lateralen Spannungsdehnungslinien eine aehnliche Tendenz bei allen Gesteinen, d.h. die Verformungskurven waren nicht linear im ganzen Bereich vom Ausgangspunkt des Belastens bis zum Punkt des entgueltigen Bruchs. Ausserdem verringerten sich das tangentiale Elastizitaetsmodul und das Verhaeltnis der lateralen Verformung zur axialen Verformung monoton mit der Erhoehung der axialen Spannung. Dennoch waren die Verformbarkeitseigenschaften der einzelnen Gesteine in der quantitativen Wahrnehmung unterschiedlich. Insbesondere war der Unterschied bezueglich der lateralen Verformungen zwischen verschiedenen Gesteinen eindeutiger, als der in den axialen Verformungen. Z.B. war die Querkontraktionszahl auf einem Spannungsniveau, das 50% der Zugfestigkeit eines Granodiorits entspricht, sehr niedrig und nah an Null. Ausserdem war die Querkontraktionszahl eines Tonalits negativ und deshalb niedriger als die eines Granodiorits. Dieser Effekt trat auf, weil die laterale Verformung, als sie sich von der Kontraktion am Ausgangsstadium des Belastens bis hin zur Ausdehnung auf den hoeheren Spannungsniveaus aenderte, positiv wurde. Es gibt keine fertige Erklaerung fuer dieses Phaenomen; es wird jedoch angenommen, dass es wegen der Mikrorisse auftritt, die vorher im Gesteinsmaterial und/oder in den schwachen Bindungen zwischen den angrenzenden Mineralkoernern existieren.

Jan 1, 2003