Search Documents

By R. D. Leitch

From time to time the Bureau of Mines has received requests from persons who wish to destroy unwanted explosives, and although the information that follows has been accumulated from sources considered reliable,4/ the. Bureau of Mines assumes no responsibility for accidents that may result from following the suggestions offered. Explosives to be destroyed may be fresh material from damaged packages, usable material for which there is no further need, or material that has deteriorated either from natural aging or from improper storage to the point where it is unfit for use.

Jan 1, 1945

By Bruce T. Olenchuk, Wils L. Cooley

Electrical grounding is essential for the safe operation of power systems. A low-impedance path to ground is necessary to prevent the possibility of dangerously high potentials in human work areas. If for any reason this ground connection becomes faulty, a serious hazard may exist. One reason for faulty ground connections is ground bed corrosion. Corrosion of electrical ground rods has plagued the power industry and appeared in coal mine power systems. This paper will investigate ground rod corrosion, its cause, and possible solutions. Included is an evaluation of various ground rods for their ability to resist corrosion under stray current conditions. -The first known study of X-it3 Rod Corrosion is also presented.

Jan 1, 1979

By Franklin P. Hall

U.S. supply and demand data for utility electricity by States and regions were tabulated for the years 1960 and 1965. Estimates are provided of State-by-State quantitative data for the utility electricity industry that can be integrated into State and regional energy balances by source, form, and major consuming sectors, and used to determine basic flow-patterns. The difficult problem of compiling interstate and interregional shipments of electricity was resolved by (a) assuming the negligibility of interregional shipments and (b) deriving a theoretical line loss percentage used for determining interstate shipments. The data developed were able to show an estimated total supply of utility electricity available for consumption. The tables also report the distribution of the supply among the major consuming sectors (household and commercial, industrial, and transportation). To compare the various energy sources of utility electricity, quantities were converted to their British thermal unit (Btu) equivalents. The Federal Power Commission, Edison Electric Institute, and Bureau of Mines are the sources of the data used in this study.

Jan 1, 1969

By Thomas M. Barczak, Ron Smith

Steel liner plates, which are bolted together to form a shell, are commonly used to provide temporary protective linings in the tunneling industry to ensure the stability of the tunnel and safety of the workers until more permanent ground reinforcement can be installed. As the ground deforms to try and close the opening, the liner plate is radially stressed, and by deforming redistributes these loads back to the surrounding insitu earth. Grouting behind the plates is done to fill any voids and ensure uniform contact to the strata around the back of the plates. Another function of the liner plate in some applications is to act as a platform or structure for the mining machine to react against in order to develop the necessary forward thrust to be able to excavate the face. In this case, the liner plates are loaded axially as a horizontal column of bolted liner plate rings, creating a jacking force against the liner plate assembly. In general, the buckling strength of the plate sections determines the jacking force capacity. Historically, the jacking force capacity of tunnel liner plates has been theoretically determined by some simplistic equations developed from tests of single liner plates. Recently, full-scale tests on a complete circular section of bolted liner plate ring segments have been conducted in the NIOSH Safety Structures Testing Laboratory using the unique Mine Roof Simulator to apply controlled loading in a manner that simulates the real world environment. Due to the unique size and capacity of the Mine Roof Simulator, these are believed to be the first full-scale tests conducted on the jacking force capability of tunnel liner plate rings. These tests indicate that the previously used theoretical equations tend to over predict the jacking force capacity of these tunnel liner plates. Unanticipated deformations in the field have been observed at loads below these theoretical design loads, therefore, a more accurate determination of the jacking force capability was needed. This report summarizes the full-scale test results, examines design parameters that impact the jacking force capability, and develops new mathematical models to improve the prediction of design loads.

By David R. Hanson

Experimental work performed by the Bureau of Mines in a laboratory environment has shown that the formation of failure zones within certain rock types is accompanied by the emission of significant amounts of radiofrequency (RF) electromagnetic (EM) energy. This radiation was detected using nonresonant, "electrically short," broad-band antennas. Rock types for which emission was observed include granite, quartzite, and taconite; sandstone and marble did not emit measurable radiation. Amplitude spectra of the radiation showed the energy to be concentrated between 10 and 40 kilohertz. These data indicate that emission is directional, but this has not yet been proven. In addition, amplitude of RF emission increases with increasing crack size. Since emission was observed only for brittle quartz-bearing rocks, it appears the formation of piezoelectric fields is a necessary condition for RF radiation. Plausible mechanisms for emission include rapid decay of piezoelectric fields accompanying the sudden stress release at failure and/or the acceleration of an "exoelectron plasma" through the intense local piezoelectric fields. Since emission appears to increase with the scale of failure, and since antennas do not need to be coupled directly to rock surfaces as with conventional geophones, the possibility of developing a portable system to monitor seismically active areas exists.

Jan 1, 1981

By Harold M. Smith

The production of oil during the early development of new oil fields is usually accompanied by large quantities of natural gas. Since In most fields gas under pressure is the main source of the energy causing the oil to move throug the sands into the wells and thence to the surface, this coincident production of natural gas will contime as long as present day producing methods are used. Generally the use of this gas is restricted, and markets are not readily available Consequently, a large portion of the gas produced at such times is often wasted by being blown into the air.

Dec 1, 1930

By J. M. Stuve

Provisional values for the heat of formation of europium trichloride and europium sesquioxide were determined by solution calorimetry utilizing europium metal of more than 99-percent purity. The resulting values for the heats of formation of Eu203 (cubic) and EuCls (hexagonal) were -386,970 ±l,200 cal/mole and -218,740 ±650 cal/mole, respectively, measured at 298.15° K.

Jan 1, 1965

By d&apos, Kathleen J. Amico

THIS SUMMARY appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U .S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed ?mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1965

By A. R. Elliott

In the early part of the your 1919 the Bureau of Mines undertook a study of methods of handling oil after it had buon produced, with the view of pointing out the losses due to evaporation and other causes. Observations on present methods show that the oil is subject to largo losses in both quantity and quality from the time it loaves tho well until it is recoivod by the pipe-lina company. During this time it is splashed into four or more tanks of various sizes and with little or no protection over the tops. From the settling tank, where the flow of oil is tamporarily stopped in order to permit sparation of ter and sediments, through the gago tanks and leaso gathering tanks to the largo tank storage where it is hold for many days, rich gasoline vapors roadily escape, especially from tho ghor gravity oil. As no effort is made to measure the oil before it reached the storage tanks, where it is delivered to the pipe-line company, the lossos of the light products of the oil can only be approximated, and, as final results will show, are no doubt usually very much underestimated. In conducting this investigation, the Bureau has endeavored to make tests that would show quantities and values lost, in order to impress better upon those concerned what might be saved through a little more diligence. Eperiments were conducted on both California and Mid-Continent oils. The field operimental work done in California, on which a report is to be published in the near future, is cutlined briefly below: The field work consisted in collecting from operating companies data on storage of oils in large tankage and in performing experiments in the field on storing and piping oil to small lease tanks under practical conditions. Acourate Easurements were takon on the volume, gravity and gasoline content of the oil as it passed through the various stages in its removal from the lease. The work extended over the four seasons of the year in order to obtain better the effect of varying winds and high and low atmospheric temperatures during those periods. Thanks are due to the many oil operators who have taken a personal interest in the work and gave valuable information and assistance. One company furnished the oil and tanks and much of the apparatus and labor. This company also per- mitted the work to be done on its properties in the Coalinga field. This was of material aid, as the results were to be comparative and therefore it was necessary that the same gravity oil be used throughout the experiments.

Oct 1, 1920

By H. K. Sacks

The Bureau of Mines has improved a mine dust incombustibles analyzer originally developed at the Bartlesville Energy Research Center (BERC). This analyzer provides quick, accurate analysis of the percentage of incombustible material present in dust samples taken from mine ribs, roof, and floor so that costly overdusting may be eliminated while still maintaining a proper level of incombustibles. The changes being effected on the present design of the BERC model IV rock dust analyzer should simplify its operation and calibration procedures, resulting in increased accuracy.

Jan 1, 1976

By D. J. Parker, D. Harrington, L. H. Harrison

The necessity for protection against the hazards of lightning manifests itself from time to time in the mining industry by reason of loss of life, damage to electrical equipment, fires in surface structures at mines, and accidents in the handling and use of explosives. This paper is intended to assemble, correlate, and present some of the salient. points embodied in the available literature on the subject and at the same time give some factual data concerning instances of such loss of, life and damage to property, with special application to the mining industry The annual loss of life and destruction of property by lightning is considerable; the former may be prevented to a limited extent, though use of common sense as to exposure is required and not always followed; the latter can be prevented to a considerable degree. The manufacturers of electrical equipment,, through improved types of lightning arresters,, have done much toward the protection of electrical equipment, with consequent safeguarding of life and of property. Education based on unfortunate experiences has gone far to discourage the handling of explosives and blasting accessories during thunder storms, especially in open pits and quarries, and to a much smaller extent in underground workings. The lowly lightning rod plays an important role in the protection of certain types of buildings (especially isolated buildings), stacks, monuments, and other structures. LIGHTNING PHENOMENA In 1751, Franklin proved that lightning was simply a visible display of electricity - an extended spark; and until a generation ago little had been added to his exposition, to define the various phases of the phenomenon. Matters pertaining to lightning are discussed in the following references:

By d&apos, Kathleen J. Amico

THIS SUMMARY appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operatons at or near mines.

Jan 1, 1963

By L. C. IlsLey

Coal mining is more widely distributed throughout the United States than is generally known, as 30 States are credited with having coal mines. In 1919 twenty-three of these States each produced at least a million tons of bituminous coal, and all the States produced about 560,000,000 tons. In addition, Pennsylvania produced about 85,000,000 tons of anthracite. Twenty-eight States have regulations prepared by commissions or have enacted laws governing the operation of coal mines. Pennsyl¬vania has separate codes for the anthracite and bituminous fields. The codes may be classified as follows: Twelve distinctly coal¬mining codes; eight codes that are essentially coal mining, but also apply to other mines; five codes that are subdivided, referring partly to coal mines and partly to other mines; and four codes that are essentially metal mining, but apply in part or in whole to coal mining. The first State to have a coal-mining law was Pennsylvania, which enacted a law, for Schuylkill County only, in 1869. The first State to enact a coal-mining law governing all the coal mines in the State was Illinois in 1872, followed by Ohio in 1873. Pennsylvania in 1879 enacted a law for anthracite mines only, but did not enact similar laws for bituminous mines until 1577. At least 10 other States enacted coal-mining laws between the years 1870 and 1890. Before 1890 electricity was little used in coal-ruining operations and therefore practically no provisions governing the installation, inspection, or maintenance of electrical equipment were made in any of the laws enacted up to 1890. In the law of Colorado, approved April 8, 1885, there is a reference to the use of telephones, probably the first reference to electrical equipment of any kind in a State-mining code. Most of the mining codes have been changed from their original form by amendment or by complete revision. In some of the early changes a casual reference is made to the use of electricity or to the handling of electrical equipment. In 1911 Pennsylvania added

Jan 1, 1920

By John J. Mulligan

Lead-silver deposits in the Omilak area, on the western slopes of the Darby Mountains, Seward Peninsula, Alaska, were investigated by the Bureau of Mines, during the 1953 and 1954 field seasons, as a part of the U.S. Department of Interior's continuing program for the development of Alaska's resources. The Omilak area was the scene of early day prospecting and mining activity. The Omilak mine, which operated from 1881 to 1890, was the second producing lode mine in Alaska; the first was a small gold mine near Sitka. Several hundred tons of ore were produced at the Omilak mina; as an indication of grade, 41 tons shipped from Omilak in 1889 contained 75 percent lead and 142 ounces of silver per ton. A prominent, nearby occurrence of lead-silver minerals, found but not explored during this period, has since become known as the Foster prospect. Subsequent exploration of this prospect revealed an abundance of massive galena occurring on an outcrop and as float scattered through limestone talus. Evidence of lead deposition, together with the generally high silver content of lead ores previously shipped from the district, indicated that deposits might be found which would be commercially valuable even in this remote area. To investigate the possibility, the Bureau of Mines made a reconnaissance of the Omilak area and did bulldozer trenching, diamond core drilling, and sampling at the roster prospect. Data resulting from the investigation are presented in detail in this report and are summarized in the following paragraphs.

Jan 1, 1962

By J. R. Bartels

Operation of underground coal mine mobile equipment is usually done in a restricted workspace with reduced visibility. This work environment puts machine operators in awkward postures for tasks that require awareness of their surroundings and fast reactions to avoid hazardous situations. Using experienced equipment operators as a source, researchers conducted an investigation that developed a method to gather data on the needs and practices of machine operators while controlling the machine and the reasons for needing particular operational cues. The method used was an interview technique including a survey questionnaire and visual aids. The data gathered defined operator cues and work positions for the cutting and tramming phases of remote controlled continuous mining machines used in underground coal mines. Analysis techniques to determine which cues an operator sees from a variety of positions utilizing a computer simulation is shown to be potentially useful to the mining industry for design of work practices and workplace layout and could impact equipment design and selection for improved worker safety. Conclusions indicate that the survey was a good research tool to collect data and helped investigators understand important visual cues. Using this information, researchers were able to analyze the visual cues an operator can see from a given work position and posture.

Jan 1, 2009

By G. S. Rice, H. P. Greenwald

"Experience and experiment have goth shown that a cloud of coal-dust in air can be inflamed and an explosion developed only when a certain minimum concentration of the dust in air has been equaled or exceeded. Those who have had experience in the handling of coal know that dust is frequently present in the air and may be of sufficient density to obscure an ordinary electric light at a distance of 40 or 50 feet; yet flames may be, and times without number have been, introduced into such clouds, when no additional coal-dust has been stirred up, with no effect other than the burning of the dust particles which actually enter flame. Evidently the density of the dust cloud is insufficient to give self-supporting combustion.The minimum amount of dust in air required to give a spreading flame will vary with a number of factors such as the composition of the dust and its size. This amount in a unit space may be considered analogous to the lower limit of inflammability of fire damp (methane) in air, although the variation in limit of explosibility of gas is small even when conditions of the experiment are altered. In large-scale determinations of the lower limit of inflammability of coal-dust there is no certain method by which a sample of the dust cloud can be snatched and its density determined. It is necessary to produce the best possible dust cloud from a known weight of dust, in a known volume and assume - probably with considerable error - that the dust cloud is reasonably uniform. The dust cloud must be formed and the source of ignition applied to it simultaneously; this is generally accomplished by the use of blow-out shots of black blasting powder, dynamite, or similar explosive so prepared as to blow out like a cannon shot, or by a gas explosion. The more violence attending the source of ignition, the greater is the probability that all the dust is raised in a uniform cloud; and the greater the length or intensity of the flame, the greater are the chances of ignition. As a result one may obtain a variation in apparent minimum density with different sources of ignition. This difference is more apparent than real and must remain until devices for instantaneous sampling of dust clouds during explosions are perfected."

Aug 1, 1931

By E. D. Gardener, Byron O. Pichard

"Methane, frequently called fire damp or marsh gas, is very well known to coal miners but to thy average gold miner it means nothing, as it is not associated generally with the rock formations in which gold is found.We have recently been conducting a study of mine air in typical gold mines on the Pacific Coast, and out of five California mines in which the air was sampled, three showed methane. Each of these three mines, referred to below as mines A, B, and C, have had accumulations great enough to be ignited. An authentic report from another California, gold mine, which has not yet been sampled, states that recently the superintendent was seriously burned by the ignition of a pocket of gas. This mine is later mentioned as mine D.Mine A is an old mine which had been abandoned for several years and permitted to fill with water. It has been unwaterad recently, and is now being developed at greater depths. During the unwatering, gas bubbles formed on the water and upon being ignited burned freely. It is reported that two men were seriously burned from accidentally igniting the gas. Samples of the bubbles on analysis showed high percentages of methane. Since the mine has been unwatered, no trouble has been experienced through gas being ignited. However, out of a total of six air samples which we took recently in scattered working places, all showed small amounts of methane, the methane content being 0.06, 0.04, 0.05, 0.04, 0.04 and 0.07 per cent, respectively. When these samples were taken methane was not suspected, but its general presence in the mine air indicates that it is being given off constantly."

Dec 1, 1921

By R. V. Ramani, V. T. Burgos, J. A. McClay

Introduction The Cost program was developed to provide the planning engineer with a tool to evaluate the cost implications of the technical mine design decisions. Direct costing methods are employed, where feasible, to provide greater detail and accuracy in the primary cost centers. Options have been provided in the cost computation, economic analysis, and output data subsystems to increase the flexibility of the system. Computer Program The program is written in Fortran IV for use in the IBM System 360/370 computers. i. Main - The main routine reads and stores input data from three sources, user input, Cost Data Library, and data transfer from the Master Design Simulator. Data is trans¬ferred to the appropriate subroutines, as they are called, by means of labeled common blocks. ii. Subroutine CSTCOM - is a data modification routine which computes the peripheral charges related to labor and supervisory costs. iii. Subroutine MANPWR - interrogates section data to determine the total labor and supervisory costs for each cost center. iv. Subroutine CAPCST - computes the total capital investment for each cost center, including the economic life and salvage value of each element. Capital costs are determined by user selection of quantities and models of equipment. Equipment costs are stored in the Cost Data Library for retriev-

Jan 1, 1975

By R. Hogg

"Some basic features of the science and technology of particle systems are reviewed in the context of agglomeration processes. Emphasis is placed on the force of interaction among particles and with their environment and on their dependence on particle characteristics and interfacial phenomena. The complex role these forces play in the various stages of agglomerate formation, growth, consolidation and structure development, and their influence on final product properties is discussed.INTRODUCTION Agglomeration is an example of a process where the technology has generally preceded the science. Process development• has very often been by trial-and-error albeit with an eye on some basic principles. Nevertheless there is' a scientific basis to the process and a better understanding of the fundamentals can surely lead to improvements in process design and control.Successful processes for the agglomeration of fine particles depend on proper control of the adhesional forces between particles, to encourage agglomerate formation and growth and to provide adequate mechanical strength in the product. At the same time the rheology of the particulate system can be critical to the rearrangement of particles necessary to permit densification of the agglomerate and the development of an agglomerate structure appropriate to the end-use requirements.AGGLOMERATION SYSTEMSUltimately, the performance, of any agglomeration process depends on the• characteristics of the particles and their environment. The specific effects, however, are often complex and may be very difficult to pinpoint by simple observation of the process. A typical agglomeration process involves a number of concurrent or consecutive steps - adhesion, growth, compaction, etc., - each of which is affected by the characteristics of the system, but not necessarily in the same way. The effect of particle size, say on agglomerate growth may be quite different from its effect on compaction and its optimum value may differ widely from one stage to the other. Obviously there.is a general need for compromise in the design and operation, of agglomeration systems. Furtnermore, an understanding of the details of the process and their complexities can be critical to process optimization and improved product quality control."

Jan 1, 1989

By ROBERT R. ROUGH, FRANK L. BACON, John Dasher

(being shipped as bailast in ocean freighters). Within the last 10 years it has become more economical to use local sands, and there has been a general shift from the Belgian sand. Deposits of purer sand were treated and used for 'some time: but the suprly became limited, and means were sought to beneficiate the more bountiful subpay-f impure beach sands. These sands are composed of, 50 percent feldspar and 50 percent quartz, with small amounts of iron- bearing minerals, The most objectionable impurities in these West coast sands are the oxides of iron and aluminum. The Del Monte (Calif.) beach sand contains about 0.13 percent FeqQg and about 11.0 percent Aig03 (the latter being furnished by the large amount of feldspar present.) For the manufacture of feldspar present.) For the manufacture of flint-glass containers the maximuni quantities of these two impurities permitted in the sand are 0.05 percent F20 and 6 to 8 percent A1203.. The Fe0g occurs in the sand as follows: Traces of iron-bearing minerais resistant to weathering, ferruginous clay stains on the sand grains, and iron minerais not visible and possibly in solid solution or as colloidal incisions in the grains of feidspar or quartz. A good part of the iron in the sand is present in the traces of iron-bearing minerals, biotite, ilmenite, garnet, monazite; and hornblende. Biotite is present in larger quantities than the others. Samples of quartz, were freed of iron-bearing minerais by the use of heavy liquid (sp.gr. 2.70), leached with boiling HCI and SnCl2. Under a microscope a few apparently clean quartz grains were selected, and Fe203 was determined spectrographically to be 0.03 percent. The technique is similar to that described by Gabriel and Slavin. 4/

Dec 1, 1943