Search Documents

By R. Hogg, E. Kaya

"The presence of agglomerated particles in airborne dust in coal mines has been confirmed by SEM examination of static samples collected on substrates. In addition, the effect of agglomerated particles on the performance of cascade impactors and cyclone-type personal samplers has been studied. Simple procedures have been developed for evaluating the extent of agglomeration in air-borne dust by comparing the observed size-selectivity of the sampling devices with that expected under idealized conditions. Applications of these techniques in the laboratory and in underground mines are discussed.INTRODUCTIONAirborne dust is invariably present in mine atmospheres. Particle size is a primary factor in determining the behavior of the dust, its effects on miners' health and the effectiveness of dust control measures. Obviously, agglomeration of the dust particles can have important effects on: ""natural"" dust removal processes such as settling• the use of water sprays etc., for dust control• pulmonary deposition characteristicsIn addition, the presence of agglomerates could influence the effective toxicity of the dust. For example, ultrafine particles are often thought to be relatively unimportant in the development of respiratory ailments because of their low deposition efficiency. However, the latter could be substantially increased if such particles were present in larger agglomerates. It is by no means obvious that there should be significant agglomeration of the airborne dust in a mine atmosphere. In fact, calculations based on the classical coagulation theories indicate that, at the kinds of dust concentrations that exist even in what would be regarded as “very dusty"" atmospheres, the coagulation half-time* .should be of the order of weeks or even months. On this basis, agglomeration would be expected to be essentially negligible. On the other hand, laboratory experiments (Polat et al., 1991) have revealed very extensive agglomeration in the airborne dust released during the crushing of individual coal and mineral particles. It is postulated that such agglomeration occurs immediately at the point of dust generation. In other words, many of the fine fragments produced on fracture are never completely separated from their neighbors."

Mar 1, 1992

By Oleg Terichow

The Bureau of Mines studied the penetration of a slender cylindrical tube into a sand bed, simulating seafloor material under the application of a static load. The factorial experimental design was based on three factors: tube diameter, geometry of penetrating bit, and seawater saturation of sand, all of which were found to be significant in influencing the depth of penetration. The geometry of the penetrating bit, or shoe, is of major significance in the mechanics of penetration and should be considered the most important factor for additional study. Linear regression analyses of the load-penetration data show that the relationship is linear.

Jan 1, 1970

By Homer J. Ballinger

A multiple drill carriage or "jumbo," which is believed to be unique in both design and performance, was constructed and has been in use for the past year at the Bureau of Mines experimental oil-shale mine near Rifle, Colo. This jumbo mounts four long feed percussion drills and is so designed that two men can operate all four drills. Before the jumbo was placed in operation, a minimum of eight man-shifts was required to drill 72 fifteen-foot holes in headings 60 feet wide and 27 feet high. The sane round is now drilled by two men in about 6 hours. Over 500 feet of drilling per man shift is easily and consistently accomplished. Use of the jumbo has resulted in a 75 percent reduction in drilling labor and a substantially lower drilling cost.

Jan 1, 1950

By Jr. Harty

Intensive work on the deoxidation of steel with manganese-silicon alloys by the U. S. Bureau of Mines has shown that the use of those alloys, which may be produced from our domestic manganese ores, would decrease the ferromanganese requirements of a very large tonnage of our steel by from 60 to 80 per cent and in some cases by 100 per cent. The open-hearth heats made with these alloys have been of excellent quality. The tonnage of our ferro-grade ores Which has been made available by the bureau's ore-dressing studies, combined with the products resulting from such processes as those developed by the bureau and by Bradley for Cuyuna ores, should easily fill our reduced ferromanganese requirements when manganese-silicon alloys and ordinary Spiegel are used in the way described in this report. There are no technical difficulties in the application of this practice, and any difficulties involved in its wide and immediate application would only be those arising from habituated ideas of the necessity of ferromanganese. General acceptance of this practice and development of the available sources of domestic ferro-grade material by already proven processes should make this country independent of foreign ores. This paper resents the results of work done under a cooperative agreement between the Pittsburgh Experiment Station of the United States Bureau of Mines and the Carnegie Institute of Technology, the Metallurgical Advisory Board, and the University of Pittsburgh, Pittsburgh, Pa.; between the Mississippi Valley Experiment Station of the United States Bureau of Mines and the Missouri School of Mines and Metallurgy, Rolla, Mo.; between the North Central Experiment Station of the United States Bureau of Mines and the University of Minnesota, Minneapolis, Minn.; and between the Rare and Precious Metals Experiment Station of the United States Bureau of Mines and the University of Nevada, Reno, Nev.

Jan 1, 1931

By C. H. Herty

Intensive work on the deoxidation of steel with manganese-silicon alloys by the U. S. Bureau of Mines has shown that the use of those alloys, which may be produced from our domestic manganese ores, would decrease the ferromanganese requirements of a very large tone of our steel by from 60 to 30 per cent and in some cases by 100 per cent. The open-hearth heats made with these alloys have been of excellent quality. The tonnage of our ferro-grade ores which has been made available by the bureau's ore-dressing studies, combined with the ,products resulting from such processes as those developed by the bureau and by Bradley for Cuyuna ores, should easily fill our reduced ferromanganese requirements Then manganese-silicon alloys and ordinary spiegel are used in the way described in this report. There are no technical difficulties in the application of this practice, and any difficulties involved in its wide and immediate application would only be those arising from habituated ideas of the necessity of ferromangenese. General acceptance of this practice and development of the available sources of domestic ferro-grade material by already proven processes should make this country independent of foreign ores.

Jan 1, 1931

By E. D. Gardner

"The Bureau of Mines has studied blasting practices in metal mines of the Southwest. The investigation of blasting drift rounds showed among other results, that cut-holes in ground difficult to break could be chambered to advantage under some conditions.In open--cut mines, chambering nearly all holes before blasting is the common practice. Two or more free faces are generally maintained in this type of work, and the amount of explosive necessary to break any bench or bank can usually be estimated from the yardage to be moved. However, in blasting drift or tunnel rounds only one free face is available before the cut-holes are shot, and the quantity of explosive required is generally ascertained best by trial.In addition to being the most difficult to break, the cut-holes are the most important of a drift round. When the cut-holes ""break bottom"" less work is required of the other holes, and a full break of the round is generally obtained. In ground difficult to blast, extra care and expense are justified to insure that the cut-holes ""break bottom.""At many mines the work is so organized that all blasting is done at the end of the shift, and a decided advantage would have to be gained to make chambering of the cut-holes economical. Also, in many mines blasting during the shift would not be practical. One or two holes could probably be drilled during the time necessary to do the chambering. However, under certain special conditions, such as in small operations or those where ""leasers"" or contractors are working, drill holes could be chambered should there be an advantage in doing so. Moreover, in some mines it might be practical to chamber the cut-holes at the lunch hour. In ordinary rounds the cut-holes are generally drilled by noon. It would not be necessary to tear down the drill or remove tools from the face to do this work of chambering."

Feb 1, 1928

By Forrest T. Moyer

In conjunction -with the statistical survey of the lime industr-.r in 1939, by the Bureau of Hines, producing companies reported the lime-fuel ratios attained in their plants according to type of kiln and kind of fuel. Each ratio, expressed as the number of pounds of lime burned by a unit quantity of fuel, was weighted according to the tonnage of quicklime pro- . duced at the reporting plant and grouped with similar data from other plants, so that an average ratio for each type of fuel and,kiln could be calculated. By this method the variables trat affect ratios of individual plants are more or less equalized, and the computed average lime-fuel ratios provide a fair measure of kiln and fuel efficiencies during 1939.

May 1, 1941

By A. E. Wells

"When the United States entered the World War, the heavy requirements for sulphuric acid in the manufacture of explosives made necessary a definite knowledge of the sulphuric acid capacity of the country. The Bureau of Mines, under the authority conferred by the explosives regulation act, made a thorough survey of the sulphuric acid situation. In this work, which was personally directed by the writer, comprehensive data were collected on the situation and capacities of the various acid plants, sources of supply of raw materials (brimstone, pyrite, pyrrohotite, zinc ores and concentrates, waste sulphur dioxide gases from copper smelting, and spent oxide from gas works), the principal points in regard to manufacturing processes (chamber and contact) and the uses of the acid. The results of this investigaion have recently been published by the Bureau of Mines, as Bulletin 184, entitled ""The Manufacture of Sulphuric Acid in the United States"" by A. E. Wells and D. E. Fogg. The following paragraphs on the uses of sulphuric acid are abstracted from this bulletin.Sulphuric acid is one of the most important of all chemicals, not only because of the large quantities manufactured but also because of the wide use of the acid in many different industrial works. Sulphuric acid is to the chemical industry what iron is to metallurgy. The general public, however, does not realize this fact, for sulphuric acid does not appear in the finished product as does iron and steel, but is only a means to an end. It is essential in many industries, such for example as in the manufacture of phosphate fertilizers, explosives, dyes and petroleum products. In recent years in the United States, especially in the East, the demand for sulphuric acid for chemical and metallurgical industries has been an accurate and sensitive barometer of the general business conditions. This demand for acid responds much more quickly to a general slump or boom in the industrial world than does the demand for iron and steel."

Oct 1, 1920

By Thomas Varley

"Concentration, ore-dressing, or the dressing of minerals are common terms used in metallurgy and indicate processes of separating valuable minerals from worthless gangue. It is understood, of course, that the products from such processes, being separated from the various minerals and gangue, are ready for commercial sale or for further treatment by smelters and refineries.Gravity concentration takes advantage of the difference in specific gravity of the various constituent minerals and gangue of waste material in the ore. The two most common forms of concentration by this means are jigging and table concentration. Jigs usually are used in the separation of relatively coarse material and the tables for the finer material, the line of division in general being about 20 mesh.There are mar factors to be considered .before a decision can be made as to what method would be best adapted to the successful treatment of an ore and only by careful experiments can this be determined. Among the important factors to be considered are. The nature of the minerals present, their physical and chemical relations to the gangue material, and the gangue material itself. Perhaps the most important is the number of minerals present and their relation to each other.Metals exist in ores in three principal forms -- sulphides, oxides or carbonates, and native. Concentration by gravity methods is in general best suited to sulphide ores, although in some places considerable success has, been obtained in the concentration of oxide ores by gravity methods."

Apr 1, 1920

By David F. Smith

The American Society for Testing Materials4 has recommended that the melting temperature of potassium chromate be used-for indicating the temperature to which a coal sample should be heated in the standard method of analysis to determine its volatile matter content. The specified temperature is 950± 20° C., the melting point of potassium chromate being noted as 940° C. Le Chatelier5 originally found the melting point to be 975°; later6 he found 9400. According to Shemtschushny7 the melting point is 984°; he also found a transition at 679°. Groschuff8 found the melting point to be 971° and the transition temperature 679°. Amadori9 reports a melting point of 9.78° and a transition point of 666°. The International Critical Tables10 take the melting point as 975°, which is estimated to be correct to two significant figures. In view of the apparent uncertainty existing, it has been though worthwhile to make a careful redetermination of this datum. It is of interest not only to determine the melting point of the pure salt, but also of the commercial product, in order to test its suitability for use as a temperature indicator. The work was suggested by A. C. Fieldner, chief engineer, experiment stations division, U. S. Bureau of Mines.

Jan 1, 1929

By A. W. Khair, L. D. Gehl

"This paper describes the study of bit wear characteristics on three types of rock namely Tennessee sandstone, Berea sandstone and Indiana limestone. High content of quartz with quartz cement in Tennessee sandstone causes removal of material from the bit body and dam2ge to the tip of the bit resulting into excessive weight and height loss as compared to other two types of rock. The drum speed and water spray pressure do not contribute significant effect on bit wear. The polycrystalline compact diamond (PCD) tipped bits are more wear resistant than the ordinary tungsten carbide (WC) tipped bits, but, due to wider body of PCD bits, the wear rate increases particularly at greater depth of cut. INTRODUCTIONThe impact of bit-rock interaction during the cutting process in underground coal mines has always attracted the-interests of mining operators, researchers and the manufacturers. Coal cutting bears directly on airborne coal dust generation which causes ""black lung"" in coal workers. On the other hand, rock cutting generates frictional sparks causing face ignitions. The bit wear not only produces airborne rcspirable coal dust , but also affects the productivity, safety and economy. Hun and Evans (J) concluded that the point attack bits have greater ignition potential than the conventional wedge shaped bits. The results of a study (2) suggested that after 7% of weight loss, the bit should be replaced. In a survey study (3), it was found that the bit consumption of bit had an effect on the productivity and utilization of the continuous miners. The mining industry is yet to receive a solution which could provide them with optimum operating parameters for coal cutting machines in underground C9al mines.The study was, therefore, taken up to determine wear characteristics as influenced by the rock propenies and varying operating parameters. For the purpose of this study, three types of rock, Tennessee sandstone, Berea sandstone and Indiana limestone were used. The machine operating parameters included (i) drum speed, (ii) water spray pressure and (iii) bit type. Besides studying the wear characteristics, the effects of these parameters on the required cutting force, specific energy consumption, acoustic emission generation and bit temperature rise were also studied. Also, the preliminary experiments were performed to compare the bit wear between PCD and WC tipped bits."

Dec 1, 1995

By Charles T. Chislaghi

An economical, remotely operated (automated), temporary roof support (ATRS) has been developed by the Bureau of Mines for use on a single, fixed-head roof-bolting machine (squirmer) that operates in low coal seams (less than 42 in thick). The ATRS eliminates the need for squirmer operators and helpers to go under unsupported roof to set or remove temporary support prior to or during the roof-bolting cycle--a task that annually accounts for approximately 20 pct of all roof fall fatalities. The ATRS can be adapted to any squirmer used in the U.S. low coal fields. A prototype ATRS was field-tested at Imperial Colliery Co.?s Mine No. 20 in Eskdale, W. Va. The Mine No. 20 amended roof- control plan, which requires the use of the Bureau?s ATRS as temporary support during face bolting, has been approved by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor.

Jan 1, 1982

By Daryl E. Radcliffe

The Bureau of Mines studied the displacement of the roof in a portion of the Bear coal mine near Somerset, Colo, Horizontal-and vertical-displacement gages were installed in a five-entry section during normal room-and-pillar mining procedures. Monitoring of the roof continued until this section was mined out. Displacement measurements in combination with known time lapses between mining and bolting operations indicate that once support is achieved, the length of unsupported time does not appear to affect long-term roof stability in the mine under investigation.

Jan 1, 1978

By J. B. Littlefield

This study is one of at number conducted to determine the concentration of dust in the air during the complete cycle of operation in wet drilling; information as to various factors connected with, drilling in mining operations is considered to be of definite value in the control and prevention of air dustiness, and it in particularly desirable to ascertain whet features of present-day wet-drilling operations in mine work contribute to dust disease and to remedy deficiencies when they are found.

Jan 1, 1938

By Alvin M. Cummings

"INTRODUCTION During July and August 1943, the Bureau of Mines undertook an investigation of the Trego lead-zinc mine, near the town of Platteville in Grart County, Wis. as part of a general investigation of the zinc-producing area of southwestern Wisconsin. The work was done when every effort was being made to increase the production of metals important to the nation's war program.The Bureau of Mines completed eight churn-drill holes and sampled mineralized faces in the mine workings to determine if further exploitation was justified in an area between the mine and a zone previously drilled to the east.Following the investigation described herein, intermittent operations were resumed. Except where otherwise stated, this report describes conditions only to the time of completion of the Bureau of Mines investigations.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyzes samples and performs beneficiation tests.The investigation described in this report was conducted under the immediate supervision of the author and 0. W. Terry, mining engineer of the Bureau of Mines, with the assistance and advice of E. D. Gardner, re¬gional engineer, and E. P. Barrett, district engineer. Final data were prepared under the direction of Paul Zinner, acting chief, Minneapolis Branch, Mining Division.A. V. Heyl, Jr., and A. F. Agnew of the Federal Geological Survey cooperated with the Bureau's engineers and made lithologic studies required during the drilling program.The cooperation of W. N. Smith and O. E. DeWitt of the Vinegar Hill Zinc Co. and Francis Piquette of the Piquette Mining Co. facilitated the investigation to a great extent."

Mar 1, 1948

By R. W. Stahl

Gas accumulation and dust suspension are the major safety hazards in coal stockpiling and reclaiming operations. This report presents a schedule of safety precautions and plant design features devised by the Bureau of Mines to reduce danger from these and other sources.

Jan 1, 1965

By Stephen A. Swan

Bureau of Mines researchers have collected and evaluated rollover protective structures (ROPS) f or more than 10 yr. ROPS and falling object protective structures (FOPS) are required on specified mining machines under regulations of the Mine Health and Safety Administration (MSHA). Both ROPS and FOPS are required on mining machines used in surface coal mines and surface areas of underground coal mines (30 CFR 77.403 and 7 7.4 13a), and ROPS are required on mining machines used in metal and nonmetal mining operations (30 CFR 55, 56, and 57.9-88). This illustrated manual provides mine safety personnel, MSHA inspectors, and original-equipment manufacturers with guidelines and a check- list for inspecting ROPS being used in the field. The manual discusses specific requirements of the MSHA regulations and minimum inspection and maintenance checks for ensuring compliance with those regulations. An easily reproducible checklist is provided as an aid to the inspection of ROPS.

Jan 1, 1985

By Henry W. Busch

Determination of the aldehyde content of Diesel-engine exhaust gas has proved rather cumbersome and unsatisfactory when carried out in its entirety in field investigations; therefore, studies were conducted with a view to developing methods by which samples might be collected in the field and trans-ported to the laboratory for analysis. Experience also indicated that aldehyde samples collected in water solution and then transported to the laboratory sometimes underwent serious changes in composition if several days elapsed between sampling and analysis. Polymerization of the aldehydes, which takes place readily in dilute aqueous solutions, may have been the cause of such changes. Because of these difficulties, experiments were conducted to find a suitable stabilizer or preservative for dilute aqueous solutions of the aldehydes that occur in Diesel-engine exhaust gas, so that in field studies a known volume of gaseous sample might be collected and brought into contact with water, and the resulting solution of aldehydes analyzed in the laboratory at some later time with reasonable certainty that the results would represent the composition of the original sample,

Jan 1, 1949

By Robert H. Merrill

A method of determining the strength of a mine roof layer in place is described in this report. The method was tested on a limestone roof layer 50 feet wide, 100 feet long, and 20 inches thick. In place measurements were accomplished by introducing air under pressure into a separation between the layer and the overlying roof, and as pressure was increased, the corresponding strain and deflection of the roof layer were measured until the roof failed. The ultimate strength of the roof agreed with the tensile strength of the roof rock (modulus of rupture) as determined in the laboratory; the modulus of elasticity as measured in place did not agree with the laboratory-determined values; the deflection and tensile strain in the layer in place showed good agreement with the theory of a body-loaded beam clamped at both ends. This procedure for determining the strength of a mine-roof layer is safer and less costly than successively widening a roof to failure. For example, it would have been necessary to mine the room to a width of 114 feet and a length of 228 feet to produce failure in this roof layer. The method is not necessarily limited to limestone; any thinly bedded rock type can be tested by this procedure when there is an open parting over the mined area.

Jan 1, 1958

By Paul T. Allsman

This paper gives the cost and describes the mining of 55 tons of nickel-bearing rock by hand methods from a prospect in southern Nevada, June 15, 1937, by the Mining Division of the Bureau of Mines. The geology, mineralogy, and problems related to future development also are discussed briefly. The main object was to obtain a 55-ton sample within the limited period during which funds were available; little time was available to make a first-hand detailed study of the possibility of commercial ore deposits being found. The sample was desired by the Metallurgical Division of the Bureau for experimental purposes at the Electro-Metallurgical Station at Boulder City, Nev. The term "ore" is used loosely in the following discussion to designate dike material containing nickel and copper, without consideration of its commercial value. ACKNOLEDGMENTS Material concerning the geology and mineralogy of the prospect and district as obtained from Geological Survey publications by Bancroft3/and Longwell4/.

Jan 1, 1938