Search Documents

By Edward F. Divers

The Bureau of Mines recently tested a sideboard device that is designed to act as an extension of conventional brattice, thus improving face ventilation of developing room-and-pillar-type coal mining. In these laboratory tests, an 8-foot-long rigid sideboard was mounted vertically along the left fender of a full-scale-model ripper-type continuous mining machine, rising to the mine roof to provide an air seal. It extended from the auger support frame pivot point outby along the fender. A novel water spray manifold was used to form an air seal between the sideboard and brattice. Tests showed improvement in face ventilation with the prototype device, and also demonstrated that water sprays can form an effective air seal over a fairly wide pressure range. Based on this preliminary study, subsequent improvements may make the sideboard concept much more effective, thus affording a simple, inexpensive technique to improve the effectiveness of face ventilation.

Jan 1, 1979

By A. Z. Dimitroff

An improvised rock- dust disseminator, consisting of a 10-gallon galvanized metal milk can that dispenses rock dust in return air currents by the injection of compressed air has reduced the float dust explosion hazards at the Koehler coal mine, Koehler, N. Mex.

Jan 1, 1965

By P. G. Clites

This study was undertaken to determine the effect of consumable-electrode vacuum arc melting on the properties of copper and to determine the applicability of the process to the production of cast shapes of copper. Ingots and castings were produced from electrolytic tough pitch copper (ASTM designation ETP), from electrolytic cathode copper (ASTM designation CATH), and from oxygen-free copper (ASTM designation OF). The products of this study were evaluated to determine the effect of the melting process on the removal of impurities from the copper and on the physical properties of the copper. The results indicate that consumable-electrode arc melting can be satisfactorily applied to the melting and casting of copper. Ingots prepared directly from electrolytic cathode copper contained slightly higher levels of impurities than are found in commercial oxygen-free copper, Excellent results were obtained with centrifugal castings of unalloyed copper, and reasonably successful static castings can be produced if proper mold and gating systems are employed.

Jan 1, 1963

By Maust. E. J., W. R. Crane

"IntroductionIn the study of mine drainage in the red iron ore mines of the Birmingham district of Alabama, an extensive series of measurements were made in order to determine the drainage from the area overlying and adjacent to the mines. Gaging rods were generally used in measuring streams, and weirs in ditches and sometimes as a check on rod work. These tests in turn were checked by current meter tests. In all, 725 separate stream gagings and 97 weir measurements were made. Certain relationships were worked out, particularly between rod and weir tests, which permitted obtaining results that are much more accurate 'under the existing conditions, than any available formula would give. The large number of weir measurements and the period covered by the tests made it impracticable to construct a weir for each observation so portable, adjustable weirs were built. The methods used are described here for the benefit of those interested in measurement of streams in connection with a study of mine drainage or otherwise. The Drainage AreaThe area draining the mining district lies between the crest of Red Mountain and Little Shades Creek, and for convenience was divided into sub-districts adjacent to certain groups of mines. Gaging stations were established on Little Shades Creek at the upper and lower boundaries of each sub-district, also at points on the tributaries near their junction with the creek. The difference between the volumes of water flowing in Little Shades Creek as it entered and left the sub-districts represents the flow from the tributaries on both sides of the creek. Since the flow coming from the sub-districts was measured direct, the inflow from the tributaries on the opposite side of the creek can be computed from the three volumes determined."

Oct 1, 1926

By B. D. Sartwell

Multiple-charged beams originating from a 300-kv ion accelerator are important tools in the study of metal surfaces and thin films. A knowledge of the particle range is necessary for an understanding of the interaction processes of the ions with the targets. Utilizing a theory developed by Lindhard for determining the range of low-energy ions in solids, the ranges of H, He, C, N, 0, and Ar ions in A1203, Al, Fe203, Fe304, CuO, Cu20, Fe, Cu, Sn, and W were calculated for the energy range 60 to 400 kev using a computer program written in BASIC. The range, presented in graphical form, is given in both µg/cm2 and angstroms. In addition, heavy ion ranges were calculated for comparison with published experimental values. For ions with Z > 5, the discrepancy between the calculated values and published experimental values generally ranged from 2 to 40 percent; the largest deviations were probably due to experimental error.

Jan 1, 1970

By C. B. Manula, R. L. Sanford, R. A. Rivell

A - Contains the coordinate pair information for deriving the co¬efficients of the 3rd degree polynomial which approximates the loading station equation. C(N) - Coefficients for third degree approximating polynomial. I - General DO LOOP variable. K - Position in BRANCH of next character. L - Format specification in DEFINE FILE statement. X - Uniform displacement for random uniform number. Y - Load increment At. AO-A3 - Coefficients of approximating polynomial for loading station equation. GR - Grade direction, or grade resistance. IQ - Counts quadruples of distance grade speed and end of route for determining total distance. IT - Intersection counter in XXXDEF. Il - Station number trip is leaving. Jl - Station number for trip destination. J2-J8 - Motor assignments and functions for given trip. KK - Location of starting grade and distance in DISTGR KK - Position of decimal point in real number. KZ - DO LOOP variable for motor assignment check. LL - Location of ending grade and distance in DISTGR. Ll - Position in IECB of station satisfied. L3 - Next available position for IECB sort. MM - Flag for printing the failure of sanding to overcome slippage. NN - Trip destination in MOTSER RR - Rolling Resistance. XK - Station level or type.

Jan 1, 1974

"As stated earlier the primary goal of the Generic Mineral Technology Center for Respirable Dust is to reduce the incidence and severity of respirable dust disease through advancing the fundamental understanding of all aspects of respirable dust associated with mining and milling and the interaction of dust and lungs. While initial work was directed to coal dust the charge to the dust center has been expanded to include diesel particulates and asbestosis, the latter of deep concern not just to workers in the mineral sector of the economy but also to the general populace.A major facet of Dust Center research has been the analysis and documentation of comprehensive research protocol and procedures that are appropriate state-of-the-art in the various areas of respirable dust. In addition to definition of standardized research protocols and procedures which would be utilized by center personnel for uniformity and reproducability there is a considerable need for utilizing standardized respirable dusts in experiments with consistent, reproducible characteristics which simulate those of actual mine dust. This respirable dust needs to be available in large quantities for a wide variety of research uses that include animal and medical experiments. The dust must be free of the lubricating oils and grinding wheel contaminants that are frequently encountered in laboratory generated dusts.The holistic approach to establishing standardized protocols and procedures applicable to the five major research areas of the center is presented in Figure 5.In one hypothesis, range in coal volatility is considered to be a major causal factor in the incidence and severity of pneumoconiosis. Therefore a suite of characterized standard respirable dust samples have been prepared for researchers from coals representing the western (high volitile A bituminous), central (medium volatile bituminous) and eastern (anthracite) mining areas of Pennsylvania. Quartz, limestone (rockdust) and kaolin clay samples, representing important mineral constituents of coal dust have also been prepared.A suite of medical investigations have been developed utilizing small and medium size animals as well as non-human primates in a variety of dust/lung interaction projects which will be discussed in the next section. A number of respirable dust sampling and dust generation methods have been investigated and selected techniques utilized for both in-mine and in-laboratory research investigations. These will also be discussed in more detail later. A wide range of respirable dust size, chemical and mineralogical analyses have been investigated, standardized and documented for use in various research investigations.This interaction and documentation of various respirable dust sample procedures, animal and medical tests, sampling and dust generation methods, plus size, chemical and minerological analysis applied in the five major areas of research investigation have served to create a very favorable synergism and rapid technology transfer in the respirable dust center."

Jan 1, 1988

By Walter C. Lorenz

Samples of materials containing pyrite from various coal mines and coalbeds were studied to compare their compositions and oxidizing characteristics. Pyrite was the only form of iron sulfide identified, but X-ray diffraction, emission spectrography, and microscopic analyses revealed similar suites of minerals and trace elements. The pyrite occurred usually in spherical clusters of very small crystals. The oxidation of pyrite in solutions of PeSO4 and Fe2(SO4)3 and in the presence of an iron oxidizing bacterium Ferrobacillus ferrooxidans, was studied through a manometric technique. FeS04 or Fe2(SO4)3 solutions had no appreciable influence on pyrite oxidation under the test conditions, The bacterium acted as a catalyst, greatly increasing the oxidation rates; however, in three samples that also contained calcites, bacterial oxidation was greatly reduced. The oxidation rates also increased approximately as the percentage of pyrite in the samples increased. For the series of samples studied, there was no definite correlation of the results with the location of the various mines nor with the acidity of alkalinity of the mine drainage.

Jan 1, 1963

By Andrew B. Cecala

This U.S. Bureau of Mines report provides a detailed description of the Bureau-designed modified shearer clearer system. Engineering drawings are provided for all major components of this system. The modified shearer clearer system is a revised version of the original system and is intended to improve the ventilation around both cutting drums. The original shearer clearer technique was solely a dust control technique that has been effective in lowering shearer operators' dust exposures. The technique uses a series of water sprays that not only knock down a portion of the dust cloud but also act as small fans that move a substantial amount of air and keep the dust cloud from dispersing over the shearer body. The modified version is composed of two additional spray blocks for improved air movement around both cutting drums, thus lowering methane levels and the likelihood of an ignition. A laboratory study performed with the modified version in a full-scale longwall gallery resulted in a 73-pet reduction in methane concentrations at the shearer machine for both cut directions. The air-moving capabilities of the system provide more turbulence at the cutting drums and reduce methane levels.

Jan 1, 1994

By C. H. Herty

[Ferromanganese continues to be in indispensable requirement in steel manufacture. Approximately 470,000 tons of the 80 per cent ferro-alloy was consumed in 1929 and increasing amounts will be required annually by the steel industry unless some satisfactory substitute is found. An average of 14 pounds of metallic manganese is for each ton or steel produced, The principal use of manganese is for deoxidation of the metal in the steel refining processes, although a considerable amount r s also used for the production of special manganese steels. Unfortunately, domestic production of manganese ore is inadequate to meet normal peace-time requirements, not to mention increased abnormal war-time demands.]

Jan 1, 1930

By E. J. Gleim

Many people consider the mining of coal to be an extremely hazardous occupation; but it should be remembered that most large industries have to meet special conditions which, if not dealt with properly, might become hazards to life and property. Mining men may not always be fully aware that some practices and certain equipment that is incorrectly designed or maintained can lead to dangerous conditions. In endeavoring to help the coal-mining industry to prevent accidents and disasters, the Bureau of Mines has engaged in a program of education on conditions and practices that must be avoided. An effective way to teach safety is by visual demonstration. For example, it is generally known that certain kinds of electrical flashes have ignited explosive atmospheres in mines, but actually to see and hear explosions caused by electrical sparks of different size and character under laboratory control is likely to teach a much more emphatic and lasting lesson than would be learned by merely reading about them. The interest manifested by those who witness the demonstrations seems to prove that this is true. The purpose of the demonstrations is not to discourage the use of electricity in mines, but rather to indicate what types of equipment (including some generally regarded as harmless) can ignite gas and what safeguards have been developed to prevent such ignitions. It is hoped that this information will improve the ability of mining men to cope with underground hazards.

Jan 1, 1937

By H. C. Loesche

The problem of signaling to the hoisting engineer from the cage in a shaft mine has been given considerable thought and attention by engineers and mine operators seeking to Increase the safety and efficiency of hoisting. HISTORY R. L. Rutherford,3/ an employee of the Magma Copper Co., Superior Ariz., realizing the need for a simple and practical moving-cage signaling system, began a serious of experiments early in 1937, Available electrical moving-cage signal in operation at this date required that signal wires be installed in the shaft to make a simple, positive signal without wires, the first experiments used the pipe lines in the shaft for carrying the signal current, but these experiments were not successful.

Jan 1, 1945

By A. Z. Dimitroff

An improvised rock-dust disseminator, consisting of a 10-gallon galvanized metal milk can that dispenses rock dust in return air currents by the injection of compressed air has reduced the float dust explosion hazards at the Koehler coal mine, Koehler, N. Mex.

Jan 1, 1965

By B. W. Gandrud

In the summer of 1950, Bureau of Mines engineers visited a number of coal-preparation plants in western Europe and Great Britain to obtain information on European and British coal-cleaning and froth-flotation practices. In view of the growing importance of froth flotation as a process for cleaning fine sizes of coal, it was felt that such data and information would be of value in this country, for, although froth flotation has been adopted for use in a few of our plants, it has not as yet been employed as extensively as in British and European preparation plants. Many of the important coal beds in western Europe, especially in the Ruhr Valley of Germany and in the Dutch coal-mining region of Limburg, Netherlands, are very friable, with the result that the run-of-mine product contains a large proportion of the sizes too fine to be treated successfully by any other method than froth flotation. Furthermore, the relatively high cost of producing coal from these beds has for many years made it economically feasible and desirable to treat the fines by froth flotation, especially in the coking-coal fields.

Jan 1, 1951

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

CALCULATION OF MINE HEAD LOSSES FROM ALTIMETER SURVEY DATA USBM PENNSYLVANIA STATE UNIVERSITY - MINERAL ENGINEERING DEPARTMENT USBM USBM USBM THIS PROGRAM CALCULATES PRESSURE LOSSES USING THE USBM METHOD GIVEN USBM IN USBH IC 7809 BY MCELROY AND KINGERY.1957. THE MAJOR DIFFERENCE USBM BETWEEN THIS PROGRAM AND THE CITED REFERENCE IS THE TREATMENT OF AIR USBM

Jan 1, 1977

"Fire fighting in metal mines under the best of conditions is a dangerous, a slow, and a difficult task. Certain gases generated from combustible material burning in restricted areas are poisonous, even in small quantities, and can not be breathed without serious and often fatal results. In addition to poisonous gases, smoke is given off which obscures the vision of the fire fighter and frequently prevents him from gaining access to the fire area. Many fire-fighting crews have had to turn back because their vision was so impaired by the dense smoke that the fire area could not be located and there was danger of them becoming lost in the mine.In mines having mechanically controlled ventilation - that is, mines not dependent entirely upon natural air currents - the gas and smoke can be forced ahead of the fire-fighting crews, thereby facilitating exploration of the mine and saving the time, energy and oxygen of the mine rescue apparatus crews.Where currents of fresh air can be circulated up to points near the fire without danger of seriously spreading the fire, fresh air bases can be established in the immediate vicinity, and a more intelligent campaign for fighting or controlling the fire can be mapped out.Positive air currents through forced ventilation may also result in saving the lives of miners who otherwise might have been trapped in smoke and poisonous gases.It is generally known that comparatively few metal mines have attempted to regulate or control air currents, with the result that when a fire occurs underground, the normal ventilation may be reversed, short circuited, or the air current may be in one direction one minute and in the opposite direction the next; or, generally speaking, the ventilation can not be depended upon, and smoke and poisonous gases may accumulate in any part of the mine or ""drift"" on the fire-fighters or on the miners endeavoring to escape."

Apr 1, 1921

By Harold L. Gibbs

The purpose of this paper is to encourage petrographers to prepare thin sections, as the demand for microscopic examination of rocks, ores, and metallurgical products is becoming more general in .the mining metallurgical-fields. This paper has been written with the knowledge that the successful thin-section methods and the several new techniques herein described will be helpful to all engaged in this field of work. Detailed instructions for making thin sections by methods developed at the Salt Lake-City laboratory of the Bureau of' Mines are given in this paper. Several new techniques are described for making thin sections of loose grains and fine sands and for making good thin sections of highly altered and friable rocks. The methods described insure superior bonding of the rock to the glass slide, thus virtually eliminating any failures due to parting of the section from the glass slide, and permit fast mounting, grinding, and finishing, thereby materially lessening the time required to prepare thin sections.

Jan 1, 1950

By Hylton R. Brown

Advertisements and articles in technical and trade journals announce the approach of a new age, in which plastics, light metals, laminated wood, and numerous other products or byproducts will be used in the construction of automobiles, airplanes, and furniture and equipment used in our factories, offices, and homes. Undoubtedly, after the war there will be many such developments which will introduce new manufacturing methods and new hazards to challenge the safety engineer. Already we know, from experience in laboratories and pilot plants where these new products are being tested, that there will be many fire and explosion hazards to be overcome. The danger of dust explosions may be one of the principal hazards, because thetic resins and other materials used in the plastics industry, as well as metal powders, wood dust, and other finely divided substances, are capable of forming explosive mixtures in air. Heavy losses of life and property have been caused by dust explosions in flour and feed mills, starch factories, and grain elevators, and it will be well to consider the possibilities that such losses may occur in any new industry and to provide all possible safeguards against hazards. Fortunately, we have learned something about the behavior of dust explosions and know something about the ease of ignition, limits of Explosive concentration, end pressure developed. Our efforts should now be directed toward the application of this knowledge in the development of safe operating practices.

Jan 1, 1945

By Constantine C. Popoff

During 1946 several high-grade limestone deposits in western Washington were examined by the Federal Bureau of Mines. The purpose of the examinations was to disclose new sources of industrial limestone and to indicate the commercial potentialities of little-known and undeveloped deposits. These examinations were part of a long-range program of investigation of mineral resources of the Pacific Northwest. The following report on the Whitechuck travortine deposit is one of a series prepared in the course of the investigations.

Jan 1, 1949

By W. D. Bryson

This paper is one of a series being prepared by the United States Bureau of Mines on tunnel-driving methods. The practices described are those used at No. 11 mine of the Colony Coal Co., Denver, Colo. No. 11 Mine is situated at Dines, some 14 miles north of Rook Springs, in Sweetwater County, Wyo. It is served by a spur off the Winton branch of the Union Pacific Railroad. The Colony Coal Co.'s mines were opened in 1918, and since that time have been among the largest producers of coal for the railroad and domestic markets in the Rock Springs coal district.

Jan 1, 1932