Search Documents

By R. L. Grant, R. W. Van Dolah, N. E. Hanna

An experimental investigation was conducted to assay the relation between natural gas concentration and ignitibility of the gallery atmosphere . Both the gas concentration representing maximum ignitibility and the relationship between certain properties of the explosives and their incendivity are discussed . The data show that variation in the natural gas content in the gallery can have a highly significant effect on ignitibility of the gallery atmosphere ; maximum ignitibility of the atmosphere by permissible explosives occurs with approximately 8.1 percent natural gas . The study also shows that incendivity of a permissible explosive cannot be determined only by its detonation velocity , oxygen balance , or ballistic mortar strength . However , for similar type explosives , trends observed indicate that their incendivity increases with detonation velocity or bulk strength . Additionally , for underoxidized explosives studied here , the more negative the oxygen balance the less incendive was the explosive within a class defined by salt content .

Jan 1, 1963

In December's marketing of 99.5 percent aluminum ingot, domestic producer pricing remained at 53$ per pound, while dealer quoting rose from 47.5¢ to 48.5¢. BORON Domestic production of boron minerals and chemicals reached an all-time high in 1977--1.4 million short tons valued at $236 million. Combined sales of the three California producers topped the 1976 level by 15 percent in quantity and 28 percent in value, a consequence of healthy demand in the glass and insulation industries. Unprecedented demand for boric acid as a flame retardant for cellulosic insulation stimulated producers to utilize fully all available capacity, thereby achieving a record output of 158,000 tons. One company increased output from its existing boric acid facilities and initiated production at another plant that historically had produced only sodium borates. A second company achieved a previously planned 25 percent plant expansion.

Jan 1, 1978

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

MFIRE is useful for the analysis of ventilation networks under thermal and mechanical influence MFIRE simu¬lates a mine&apos;s ventilation system and its response to altered ventilation parameters, external influences, and internal influences Extensive output enables detailed quantitative analysis of the effects of the proposed alteration on the ventilation system MFIRE was written in FORTRAN 77 and compiled with Microsoft° FORTRAN for the Intel 8086-8088 central processing units The source code is listed in appendix A for users who wish to modify the source code for operation on other computers MFIRE MODIFICATIONS OF MTU-BOM CODE The program described in Bureau of Mines Informa¬tion Circular 8901 has become known as the MTU-BOM codes MFIRE is an evolutionary product of the MTU¬BOM code with major improvements and enhancements 6 For users previously familiar with the MTU-BOM code, the following is a listing of the major improvements and enhancements incorporated by MFIRE 1 The length of an airway is an input value, LA The elevation difference of the airway is calculated from the elevation input, Z, in both programs It is possible for a data file to describe an airway that is shorter than its el¬evation difference The MTU-BOM code does not check for this error and uses the values of LA and Z This does not cause a computational problem, only a simulation problem MFIRE issues a warning message for this case, and the airway length is made equal to the elevation dif¬ference if LA is less than Z 2 To evaluate rock temperatures (average wall surface temperature of airway before a fire), it is assumed that the air temperature at an airway entrance is equal to the air temperature at the airway starting junction, and that the air temperature at the airway exit is equal to the air tem¬perature at the exit junction. The MTU-BOM code follows this assumption in all cases When a rock temperature of less than 0° F is calculated, an average temperature is used to represent the rock temperature of the airway MFIRE uses the same principle, except the consideration of unlikely rock temperatures When the exit junction of an airway is the atmosphere (a fixed condition junction), the air tempera¬ture at the exit is made equal to the air temperature at the airway beginning If an unlikely value of wall temperature (<0° F or > 150° F) results from calculations, a message is issued and the rock temperature is set equal to the air temperature at the airway exit The program user can always input rock temperature (TROCK) for an airway to override the calculated value. 3 MFIRE allows use of an optional reference airflow rate to define and limit the heat generation of a fire source This allows the simulation model to more closely resemble a real fire and to improve simulation conver¬gence Heat generation corresponds, but is not linearly related to airflow rates reaching the fire In the simula¬tion, heat generation is calculated from oxygen consump¬tion and is directly related to the variable incoming airflow Use of this optional reference airflow rate allows the heat generation to vary, but in a damped, user defined manner When the airflow rate passing through a fire source is equal to its reference airflow rate, the data items describ¬ing the fire source are not modified If the airflow rate is lower or higher than its reference airflow rate, the data items used to define the fire source are modified according to the following equations

Jan 1, 1990

By J. R. Allsup

In cooperation with the Division of Advanced Automotive Power Systems Development, Environmental Protection Agency, the Bureau of Mines studied a conventional spark-ignition engine as a prime mover for use in a hybrid system. The study involved both steady-state and transient engine operation with ignition timing, air-fuel ratio, exhaust gas recirculation, oxidizing type catalytic converters, engine speed, and power output as variables. Data were obtained from two 1971 model 350-cubic-inch-displacement engines mounted on engine dynamometer stands. When the hybrid engine was operated with an oxidizing catalyst at power output levels required for a 4,000-lb curb weight hybrid vehicle, carbon monoxide and hydrocarbon emissions could be reduced to approximately 2.0 grams and 0.3 gram per brake horsepower-hour, respectively. With exhaust gas recirculation, oxides of nitrogen emission levels could be reduced to approximately 1.2 grams per brake horsepower-hour.

Jan 1, 1974

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of the significant coalbeds of Beaver and Lawrence Counties, Pa. Washability analyses were made on seven coalbed samples, none of which were of metallurgical quality as received. Five of the samples could be sufficiently upgraded to produce acceptable products, and the remaining two samples could not be upgraded to metallurgical quality because their sulfur contents could not be lowered to meet the standard. For steam or power generation, one sample was of low sulfur content as received, one sample could be upgraded to low sulfur content, and three samples could be upgraded to medium sulfur content. The original sulfur content of the remaining two samples can be appreciably reduced by removal of the sink 1.58 speci fic gravity material; however, these coals would be classified as medium sulfur coals both before and after removal of the sink material.

Jan 1, 1969

By F. N. Kissell, R. J. Bielicki

The Bureau of Mines found sulfur hexafluoride (SF6), released from a lecture bottle, to be an ideal gaseous tracer for studying mine ventilation systems. Air samples were collected in glass syringes and analyzed by electron-capture gas chromatography. In these studies, the lower limit of detection was about 1 part per billion by volume (ppb) of SF6 per part of air. Experiments conducted in a Pennsylvania limestone mine showed this technique useful in evaluating the effectiveness of auxiliary fans, measuring low flow velocities, probing the air circulating near a working face region where ventilation appeared to be poor, and estimating volumetric flow rates in airways of large cross-sectional area and having low flow velocities. This technique was also used in a western vein-type metal mine to measure the amount of return air being recirculated into the intake air due to leakage through old stoped areas.

Jan 1, 1974

By B. Dimitriades

The Bureau of Mines measured the reactivities of 19 hydrocarbons known to be prominently present in automotive exhaust and ambient air in a smog chamber. Results agreed well with those obtained using two other smog chambers. Reactivity scales were developed for hydrocarbons and aldehydes using the results of this work and those of a previous study. Application of the reactivity scales to automotive exhaust samples gave fair agreement between predicted and observed rate-of-N02-formation values; however, predicted and observed ozone yields were neither in agreement nor did they correlate well. This lack of correlation for ozone yield was attributed to the inappropriateness of (1) the individual component reactivity data, (2) the reactivity classification scheme used, and (3) the linear summation method. In seeking to understand this problem and to develop more appropriate reactivity scales, the data were examined from a reaction mechanism standpoint, and further studies were suggested.

Jan 1, 1975

By B. J. Scheiner

Carbonaceous gold-bearing ores of the type that occur in north-central and northeastern Nevada were investigated by the Bureau of Mines as part of its Heavy Metals Program. Specific objectives were to identify the carbon and organic compounds that prevent adequate gold recovery from the ore by cyanidation and to develop an economical process that would overcome the detrimental effect of the carbonaceous constituents. Activated carbon and long-chain organic compounds containing sulfur and nitrogen were found in the ore. Part of the material consisted of stable gold organic complexes. A mild oxidation technique that allowed gold extraction as high as 96 percent by subsequent cyanidation was developed. A variety of oxidants was shown to be effective in improving gold recovery, including chlorine and sodium hypochlorite (NaOC1). An electrolytic oxidation process was developed that was particularly advantageous from an economic and effectiveness standpoint.

Jan 1, 1971

By Daniel N. Tallman

To provide technology for achieving more efficient water filtration systems for the mineral industry, the Bureau of Mines performed demon-stration filtration tests at three iron ore mines and one steel mill. A comparison of equivalently sized magnesium oxide (MgO) and sand filters showed that MgO had a higher capacity and could operate at higher fil-tration rates than sand. In demonstration tests when alum (AlK(S04)2) was the coagulant, suspended solids breakthrough occurred even though the pressure across the filter (head loss) was 7 psig or less. Under these circumstances, the MgO demonstrated 20 to 100 pct greater filtra-tion capacity, defined in terms of the volume of water filtered before breakthrough. When an organic floccu1ant was used at one location, head loss was the run-limiting factor; the filters essentially plugged with-out any solids breakthrough.

Jan 1, 1985

By W. H. Eddy

Laboratory batch and small-scale continuous flotation tests were con-ducted by the Bureau of Mines on a mica waste tailing from Kings Mountain, N.C., to determine the feasibility of producing high-quality mica, feldspar, and glass sand. Mica was recovered by two methods; one was by flotation in an alkaline circuit, which produced a mica concentrate assaying 92.0 percent mica with a recovery of 87.l percent, and the other by flotation in an acid circuit, which produced a mica concentrate assaying 91.0 percent mica with a recovery of 79.4 percent. Continuous flotation processing yielded a feldspar concentrate assaying 1.10 percent Na20 and 13.50 percent K20, with recoveries of 66.4 and 80.6 percent, respectively. The feldspar tailing was high-quality quartz glass sand analyzing 98.6 percent Si02 and 0.02 percent Fe203.

Jan 1, 1969

Provide mine personnel with a convenient means of determining the optimum installation geometry of roof trusses in bedded roof. Background Mine operators frequently ask the following questions concerning roof truss installations: 1. Where should the bearing plates or brackets be placed or where should the inclined holes be started? 2. At what angle should the holes for the inclined chords or angle holts be drilled? 3. What tension should be put into the inclined chords so as to achieve the most effective results for the effort and expense? Truss hardware manufacturers have responded to these questions with answers based on what seems to work best. While designs based on past experience are frequently reliable, there was a need for a rational approach that could accommodate a variety of conditions. The Bureau has developed a procedure that enables mine operators to optimize roof truss installations in bedded roof.

Jan 1, 1989

By J. C. Edwards

Fire experiments were conducted in the Safety Research Coal Mine (SRCM) at the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, with coal, diesel-fuel, electrical-cable, conveyor-belt, and metal-cutting fire sources to determine the response of fire sensors to products-of-combustion (POC). Metal oxide semiconductor (MOS) and smoke fire sensors demonstrated an earlier fire detection capability than a CO sensor. This capability was of particular significance for a conveyor-belt fire in which the optical visibility was reduced to 1.52 m with an increase in CO of less than 2 ppm at a distance of 148 m from the fire. Application of a neural-network program to the sensor responses from each type of fire source resulted in correct classifications of coal, diesel-fuel, cable, belt, and metal-cutting combustion with a mean of 96% of the test data correctly classified.

Jan 1, 2000

By J. C. Edwards

Fire experiments were conducted in the Safety Research Coal Mine (SRCM) at the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, with coal, diesel-fuel, electrical-cable, conveyor-belt, and metal-cutting fire sources to determine the response of fire sensors to products-of-combustion (POC). Metal oxide semiconductor (MOS) and smoke fire sensors demonstrated an earlier fire detection capability than a CO sensor. This capability was of particular significance for a conveyor-belt fire in which the optical visibility was reduced to 1.52 m with an increase in CO of less than 2 ppm at a distance of 148 m from the fire. Application of a neural-network program to the sensor responses from each type of fire source resulted in correct classifications of coal, diesel-fuel, cable, belt, and metal-cutting combustion with a mean of 96% of the test data correctly classified.

Jan 1, 2000

By M. S. Seehra, R. S. Pandurangi

"A comparative study of the intensities of the IR modes in the pjlotoacoustic and. FrIR spectroscopy of amorphous and crystalline SiO2 particles is presented. It is observed that in photoacoustic spectroscopy of amorphous SiO2, IR modes of surface species are enhanced by over an order of magnitude compared to the bulk IR modes of SiO2. This effect, though not yet understood, may find applications in surface science.Since the publication of the Rosencwaig-Gersho theory of the photoacoustic effect in solids in 1976 [1], a great deal of attention has been paid to the development .of photoacoustic spectroscopy (PAS) into an analytical technique for condensed matter studies, especially when combined with the modern Fourier transform infrared (FTIR) spectrometer [2-8]. PAS has now been applied to a variety of experimental situations [2, 3] and it is particularly suitable for opaque powders and for cases where ~ample preparation (e.g. mixing with KBr as is usually done in FTIR spectroscopy) is not desirable. Another area of interest is the depth profiling feature of PAS, which is studied by varying the modulation frequency of the incident radiation [2-8]. The one-dimensional Rosencwaig-Gersho theory for non-porous samples has been extended to other cases [9-12]. Recently it has become known [11, 12] that for porous samples with porosity the IR modes are enhanced by a factor proportional toe. This enhancement is due to the pressure wave set up in the interstitial gas in the porous sample and this enhancement has been reported by a number of groups [12-14].In this Letter we report the observation of anomalously large enhancement of the PAS signal for certain surface IR modes on the surface of amorphous silica particles. This observation differs from the previous reports in that certain surface modes are enhanced by over an order of magnitude compared to the bulk IR modes. Although the reasons for this enhancement of the surface IR modes in PAS are not understood at present, this observation may open up new approaches to the study of surfaces. Results of these initial observations are given in this Letter. ·Experimental studies reported here were carried out on an FTIR spectrometer (Mattson Instruments, Model Cygnus 100) equipped with an MCT detector. The same instrument was used for PAS studies in conjunction with an MTEC (Model 100) PA cell. The sample cell and the spectrometer are continuously flushed with dry, CO2 free air obtained by the use of Balston Instruments Air Dryer Filter System (Model 75-60). Usually data were collected for 32 scans at 4 cm-I resolution, although both scan and resolution can be varied. For FTIR studies, samples were mixed with IR-grade KBr and pelletised. For PAS, no sample preparation is necessary and data are ratioed against dry carbon black [4, 5]."

Jan 1, 1989

By D. R. Tesarik, F. M. Jones, J. B. Seymour

As part of safety and stability studies at three underground mines in the United States, researchers installed earth pressure cells and embedment strain gauges in cemented rockfill to measure stress and strain changes as mining progressed and the rockfill was loaded. Data from these instruments were used to calculate the in situ modulus of the rockfill for two of the mines. A three-dimensional numerical model of a cemented rockfill cap was validated with data from extensometers anchored in the mine roof and sill; this model was then used to estimate deformation modulus at the third mine because the earth pressure cells and embedment strain gauges recorded negligible changes. Rockfill binder used at these mines ranged from 4 to 8 per cent of the dry components by weight, the water-to-cement ratio was from 0.42 to1.0, and the largest aggregate size in the three mixes ranged from 5 to12 cm (2 to 4.7 in). The range of the calculated in situ deformation modulus values was large, but as expected, it was bracketed by modulus values for cemented tailings and roller-compacted concrete with similar cement contents and water-to-cement ratios. Dans le cadre d’études sur la sécurité et la stabilité de trois mines souterraines situées aux États-Unis, les chercheurs ont installé des palpeurs de pression des terres et des extensomètres d’encastrement dans les remblais cimentés afin de mesurer les variations relatives à l’effort et à la déformation des terrains durant l’exploitation minière et le chargement du remblai. Les données recueillies à l’aide de ces instruments ont servi au calcul du module in situ du remblai dans deux de ces mines. Le modèle numérique tridimensionnel de la semelle d’un remblai cimenté a été validé à partir des données recueillies par les extensomètres ancrés dans la voûte et dans la semelle de ces mines; ce modèle a ensuite été utilisé pour estimer le module de déformation à la troisième mine, étant donné que les palpeurs de pression des terres et les tensiomètres enfouis avaient relevés des variations négligeables. La matière d’agrégation de l’enrochement utilisée dans ces mines comportait entre 4 % et 8 % des composantes sèches par poids; le rapport eau-ciment se situait entre 0,42 et 1,0; et la taille des agrégats les plus gros dans ces trois mélanges était de 5 cm à 12 cm (2 po à 4,7 po). L’écart entre les valeurs calculées des modules de déformation in situ était grand, mais comme on s’y attendait, cet écart a été compensé par les valeurs modulaires des résidus cimentés et du béton tassé au rouleau avec des teneurs en ciment et des rapports eau-ciment semblables. [Als Teil der Sicherheits- und Stabilitätsstudien an drei Bergwerken in den Vereinigten Staaten von Amerika installierten Forscher Erddruckgeber und Einbindungsdehnungsmesser in zementierter Steinschüttung, um Spannungs- und Dehnungsveränderungen während der fortlaufenden Bergarbeiten und der Belastung der Steinschüttung zu messen. Daten von diesen Instrumenten wurden dazu verwendet, das In-Situ-Modul der Steinschüt-ung für zwei Gruben zu berechnen. Ein dreidimensionales numerisches Modell einer zementierten Steinschüttungsschwelle wurde mit den Daten von den im Grubendach und in der Schwelle verankerten Extensometern validiert; dieses Modell wurde dann dazu eingesetzt, um das Deformationsmodul in der dritten Grube zu schätzen, da die Erddruckgeber und Einbindungsdehnungsmesser nur geringfügige Messabweichungen feststellten. Das in diesen Gruben verwendete Steinschüttungsbindemittel variierte zwischen vier und acht Prozent an Trockenkomponenten nach Gewicht, der Wasser-Zementfaktor betrug zwischen 0,42 und 1,0 und die größte Zuschlagstoff-größe in den drei Mischungen schwankte zwischen fünf und zwölf Zentimetern. Die Reichweite der berechneten Werte des In-Situ-Deformationsmoduls fiel etwas breit aus, aber es fand erwartungsgemäß eine Klammerung der Modulwerte zwischen den Zemen-trückständen und dem durch Walzen verdichteten Beton mit ähnlichem Zementanteil und Wasser-Zementfaktor statt.]

This chapter analyses the parameters influencing initial design of communication systems, for new mines and upgrading existing systems. Paragraph 5.2 outlines those variables that must be taken into account during the design stages of a new wired phone system. Recommended features, general requirements, and how they can be implemented are treated in this section. Paragraph 5.3 describes ways of improving or extending the range of trolley carrier phone systems and pager phone systems already installed in the mine. 5.2 New Phone System Design The task of designing an adequate communication, control, and monitoring system for an underground mine must be addressed on a system basis. In addition to insuring that effective voice communication is established, any new system should take into account present and future requirements of remote control and monitoring functions. Chapter 4 illustrated the drastic savings in response time that can be realized when remote control and monitoring are integrated into the overall communication system. The importance of including control and monitoring in the overall design plan for any system cannot be overemphasized. Because each mine is unique, and thus usually has its own special operating characteristics and communication requirements, there is no such thing as "the one best system" to meet the requirements of all mines. The optimum communication, control, and monitoring system for a mine must be one that has been tailored to meet the special requirements of that particular mine. Factors that must be considered during system design include- a. Type of mine and mining methods (low- or high-seam coal, deep hardrock mine, stope caving, longwall, room and pillar, etc.). b. Maximum number of working sections. c. Expected mine growth rate and eventual maximum size. d. Haulage methods (tracked trolley, diesel, belt, etc.). e. Underground power distribution system (dc, ac, or both). f. Features desired (two-way radio paging, private line capability for emergency use, etc.). g. Redundant or backup systems for use during outages of the normal system. Although no two mines are alike, the following items have been established as the main characteristics desired for any underground communication system: 1. Multiple Communication Paths to Outside--the objective here is to give all telephones a second method of communicating with the surface. 2. Audible Emergency Signaling--the communication system provides the main means of alerting miners during emergencies. The system should include means to broadcast distinct audible signals for emergency signaling. Initiation of these signals should probably be controlled from. a central outside point, such as a surface control room. 3. Emergency Override--provisions should be included to permit any conversation to be overridden with emergency communication. 4. Selective Area Page--as mines grow larger it is apparent that the entire telephone system paging mode need not be activated each time a call is initiated. When the general area of a

Jan 1, 1984

Occupational illnesses are more difficult to identify than on-the-job injuries. Many illnesses related to occupational exposures may not be diagnosed until years after exposure; by that time, exposed workers may have changed jobs or left the workforce. Other approaches to identifying occupationally related illness are analysis of death certificate data (see chapter 2) and medical examination studies of workers known to have high exposures to hazardous agents. Figures 5-1, 5-3, 5-4, 5-6, 5-8, and 5-10 show, for each commodity, the percent of illness conditions reported to MSHA by nature of condition. Heart attacks that occurred on the job are reported without regard to work-relatedness. Figures 5-2, 5-5, 5-7, 5-9, and 5-11 show rates by year during 1986-1995 for selected conditions. Since there are many limitations on the accuracy of illness reporting, the frequencies and rates shown here should not be considered directly comparable across commodities. Figure 5-12 shows estimates for hearing loss by age among coal miners compared to a nonoccupationally noise-exposed population. These data come from a study by Franks [1996] of a group of audiograms obtained on coal miners by a commercial company. Using the NIOSH definition of hearing impairment, i.e., an average hearing threshold level for both ears that exceeds 25 dB at frequencies of 1,000, 2,000, 3,000 and 4,000 Hz, the figure shows that by age 30, more than 10% of miners suffer hearing impairment; by age 50, 90% of miners have hearing impairment. In contrast, only 10% of the nonoccupationally noise-exposed population suffer hearing impairment at age 51, and 50% of the nonoccupationally exposed population have hearing impairment at age 69. Figure 5-13 shows a similar analysis of commercial audiograms on male metal/nonmetal miners [Franks 1997]. At age 20, approximately 2% have hearing impairment using the NIOSH definition of hearing impairment described above. This increases to 7% at age 30, 25% at age 40, and 49% at age 50. In contrast, only 9% of the nonoccupationally noise-exposed comparison population have hearing impairment at age 50. Franks&apos; analysis showed a different pattern for female metal/nonmetal miners; they developed hearing loss at the same rate as would be expected for a non-noise-exposed female population.

Jan 5, 2000

By D. A. Reynolds, A. C. Fieldner, S. H. Katz

"03-01-192403-31-2019RI 2591 - Reports of Investigations - Department of the Interior - Bureau of MinesBureau of MinesPittsburgh Experiment Station American Society of Heating and Ventilating EngineersU.S. Public Health ServicesTucson Experiment Station Introduction.""Carbon monoxide self-rescuers,"" or simply ""self-rescuers,"" are pocketsize gas respirators which protect the wearer from air contaminated with poisonous carbon monoxide gas. On March 6, 1924, the Bureau of Mines approved the ""M.S.A. self-rescuer’ manufactured by the Mine Safety Appliances Co., Pittsburgh, Pa., after the M.S.A- self-rescuer bad passed all the tests and requirements of the Bureau's Schedule 14A4.The purpose of the self-rescuer is to help miners to escape from mines in which fires are burning or explosions have occurred, by providing protection from carbon monoxide for at least one half-hour. The self-rescuer can be used similarly by workers above ground who may through accident become surrounded or entrapped by atmospheres containing carbon monoxide.no hazards threaten the miner, who escapes serious injury by fire or violence in a large mine fire namely, ( 1) asphyxiation by poisonous carbon monoxide gas; and (2) suffocation by insufficient oxygen to support life. In order to save himself, the miner must either erect a barrica4e5 against afterdamp and wait restoration of ventilation and rescue or take a long chance at getting out of the mine through entries not permeated by afterdamp.. The self-rescuer removes the hazard of carbon monoxide poisoning for one half-hour or more, and accordingly greatly increases the miner's chance of saving his life.This paper describes the construction and details of the M.S.A. self-rescuer as approved by the Bureau of Mines, and discusses its performance under test condition"

Mar 1, 1924

By Ivette E. Torres

Table 8 provides data for the estimated value of world export trade of all mineral commodities from 1980 through 1991. It also provides a breakdown of the total into mineral fuels and non fuel minerals. These data have been developed from UN export trade data presented in table 9. The percent distribution and growth of the value of world export by major commodity groups are presented in tables 9, 10, and 11, respectively. In terms of industrial minerals (nonmetals), data in tables 10 and 11 include crude industrial minerals only, while table 8 includes an estimate for other industrial minerals. The 1991 estimates that appeared in the 1991 issues of this publication have been revised. It is typical for this section to review the year prior to the year of review because of the unavailability of data at the time of publication. The aggregated value of export trade in mineral commodities for 1992 was not available at the time of publication. The total value of nonfuel and fuel mineral exports for 1991 was about $616 billion in current (1991) dollars. The value of mineral fuel export trade accounted for about 53 % of the total mineral export trade. In 1980, the contribution of mineral fuel to the value of mineral commodity export trade had been almost 68%. The 1991 world mineral commodity export trade represents a 5.3% decrease (table 8) from that of 1990. The largest decrease was attributed to the decrease of export trade of fuel minerals (5%). The value of non fuel mineral export trade decreased by 4 %. Because the value export trade of all commodities increased by 1.2 %, the share of mineral commodities decreased from 19.2 % to 17.9 % of the total.

Jan 1, 1994

By R. E. Mussler

As part of an overall goal to develop technology that can maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines is evaluating a method for selectively extracting nickel and cobalt from low-grade domestic laterites. The method involves electrowinning to recover the metals in pure form; therefore, preliminary laboratory-scale electrowinning tests were conducted in both a nondiaphragm and a diaphragm cell to determine the effect of variables on energy efficiency under controlled conditions. Electrolytes were generally reagent-grade sulfate solutions that were prepared to simulate electrolyte that could be obtained by stripping nickel-and cobalt-rich solvent extraction reagents. Limited tests were conducted with electrolyte generated from laterite leach solutions. Electrical energy consumption in a nondiaphragm cell was 2.06 kwhr/lb Ni with the cell operated at 50° C, a cell feed of 90 g/l Ni, a pH of 3.5, an extraction of 3.2 g/l, and a cathode current density of 20 amp/ft2. The energy requirement decreased with increasing concentration and temperature, and increased with increasing. extraction and current density. At 50° C, energy consumption in the nondiaphragm cell was 21 pct greater than in the diaphragm cell, but it was only 5 pet greater at 65° C. For this reason and because of overall cost considerations, operation at 65° C with the nondiaphragm cell was preferred. Smooth sheets of cobalt were obtained by electrowinning in a nondiaphragm cell at selected temperatures from 50° to 85° C and with cobalt concentrations from 55 to 87 g/l. The energy consumption (1.48 kwhr/lb) was 22 pet lower with a cobalt concentration of 75 g/l and a cell temperature of 65° C than with a cobalt concentration of 55 g/l and a cell temperature of 50° C.

Jan 1, 1981