Search Documents

By Roy L. Wilfong

Surface area measurements were conducted on cadmium sulfide powders following thermal treatments at temperatures up to 500° C and treatment times up to 1 week. Thermal treatments at temperatures up to 300° C produced no significant changes in the surface area of the powders even after 1 week of exposure. At 500° C some decomposition of the cadmium sulfide occurred.

Jan 1, 1970

By G. B. Atkinson

The Bureau of Mines, in cooperation with McDermitt Mine, investigated a method for recovering mercury metal from mercury sulfide flotation concentrate by a hydrometallurgical technique. This preliminary report shows the feasibility of leaching mercury with a cupric chloride solution and electrowinning mercury from the solution. Proposed chemical reactions are shown in equations 1 through 3: 2CuC12 + HgS + 2CuCl + HgC12 + S°; (1) electrolysis HgC12 ?Hg + C12; (2) 2CuC1 + C12 ? 2CuC12. (3) A bench-scale leaching-electrowinning apparatus capable of treating 2.36 kg of sulfide concentrate in 11 days was operated continuously. An acid chloride solution containing, in grams per liter, 70 Ca, 60 Cu, 30 Fe, and 80 Hg was used as both leachant and electrolyte; 99.5 pct of the mercury was solubilized from the sulfide concentrate. Electrolysis of the leaching solution recovered mercury metal at an average current efficiency of 32 pct and an average energy consumption of 1.2 kwhr/lb Hg. Results from a preliminary economic evaluation indicated that a plant producing 31,500 flasks of mercury per year would have a capital cost of $3.7 million and an operating cost of $62 per flask of mercury.

Jan 1, 1983

"There mines are located in out of the way places, where timber is scarce and its price high, the problem of protecting it from fire risk is of considerable practical importance. Scarcity of timber for mining purposes is commonly met with in the more arid parts of the country, where, so, mine timbers are most likely to become dry, and inflammable, and where, therefore, the risk from fire is accentuated. Any effective and cheap method of securing adequate protection of such timber at the lowest possible cost is worthy of careful investigation. The use of magnesite cement has been suggested in this connection.The necessary qualities for any substance for the use suggested above may be summarized as follows: It should be resistant to abrasion, and to impact and structural stresses. It should be durable when subjected to the action of the elements, and stable to any minor derangements of the base on which it is placed. It must be relatively unaffected by changes in temperature, by the action of water, and should adhere to the material on which it is placed, and it should also be free from shrinkage cracks due to setting up the material, Magnesite cement appears to fulfill the various conditions outlined above.The elasticity of such cement is the outstanding quality which makes it desirable for exterior work. It also possesses the ability to adhere to all materials in a marked degree. Its freedom from expansion and contraction after setting is one of the principal reasons for its adhesive quality. It may be applied to old brick or stone walls, even tho they have been repeatedly covered with paint, and the quality of adhearing to wood makes it possible to secure a weather-proof protection to the wooden casings and trim of exterior openings. The quality of adhesion and elasticity is easily proved by applying a 1/2"" layer to a 1"" board which has been first covered with metal lath. Such a board, about 8 feet long, may be repeatedly deflected about 3"" in the center without breaking the bond to the board, or causing any cracks to appear in the magnesia cement. The ability to resist fire as well as the possession of insulating qualities are also desirable characteristics of magnesia cement stucco.Magnesite cement stucco should be applied in two coats, each 1/4"" thick on various surfaces such as wood lath, metal lath, sheathing board, brick, hollow tile, or stone; care being taken as regards the presence of lime, unless the same has been rendered, or become inert as with very old, walls. The first coat made up to a consistency that works easily under the trowel is applied in the usual manner. No water should be added to the liquid chloride as it would alter its density, and injure the work. The second or finishing coat is then applied. The aggregates are different in each, and no other dry material should be added to them as they come to the trade. The cement may be applied in zero weather without damage. Setting is quite slow under such conditions, but the cement ultimately becomes hard. It should always be applied to a dry surface excepting that under certain conditions it is desirable to apply a solution of magnesium chloride before using the stucco."

Dec 1, 1919

By Thomas V. Falkie, R. Venkataramani

The method of analysis was to test a large model containing potentially significant variables and on the basis of the results obtained, to reduce the model to one containing only the essential significant variables. This stepwise procedure of "scanning" a large proposed model and subsequently condensing the model consisted of two cycles of the same series of computational procedures. Data Preparation A majority of the variables measured were continuous over a specific range of values; for example, the variable "Width Ratio" varied in practice from 0.25 to 1.00. However, "dummy" values were assigned to certain operational variables in order that these varia¬bles would have numerical expression. The following variables were described in this manner. Variable "Dummy" Value x3: Development/Pillaring 0, if pillar extraction was being done 1, if development mining was being done x4: Boxcut/Open Cut 0, if a box cut was being made 1, if an open cut was being made The variables under consideration are represented symbolically as follows: Y: Loading rate (tons per minuts): TONS/MIN x1: Ratio, width of cut/width of cutter: WDRATIO x2: Ratio, height of cut/diameter of cutter: HTRATIO x3: Development or pillaring: D/P

Jan 1, 1972

By John C. Machisak

THE INJURY data and related employment experience of the coking industry in the United States for 1955 arc presented in this publication under the following general sections: (A) General Injury experience: Tables 1 to 9: Contain current and comparable data on operating statistics, number and classification of injuries, injury-frequency rates, and accident agencies involved in causing injuries. Data are tabulated for the industry as a whole, for each typo of oven: and for the States in which coke is produced.

Jan 1, 1958

By W. M. Weigel

Langley is about nine miles north of Augusta, Georgia., on the Sou them :l;.ilv1ay. According to the South Carolina. Geological Survey, tr.e district is known a.s tr. Horse Creek and Town Creek sub-areas of the Aileen or Savannah River Area f the South Ciil.Z'olina Coastal Plains. The geology and origin of the clays 3l"e Jscribea in a bulletin of the South Carolina Geological Survey (Series 4, Bull, l; "A Preliminary Report on Cl.:.ws of South Carolina.-), According to this report, i.he clays are sedimentary kaolins, in the Mid.dendor! and Hamburg series of the Cretaceous Age.

Aug 1, 1922

By W. L. Dare

The Federal Bureau of Mines is publishing a series of studies on the methods and costs of mining uranium on the Colorado Plateau. This report describes the longwall-mining methods and techniques used at the Radon mine, Big Indian district, San Juan County, Utah. The tabular Radon ore body lies on the southwest flank of the Lisbon Valley anticline, strikes N. 10° W., dips 7° SW., and has an average thickness of 4-1/2 to 5 ft. The mine is developed by a three-compartment vertical shaft, a haulage level driven beneath the ore, and a system of drifts driven within and parallel to the strike of the ore.

Jan 1, 1961

By James J. Olson

The Bureau of Mines recorded and analyzed overpressure levels for three production blasts at the White Pine copper mine, Upper Michigan, to obtain representative data from single-heading blasts in a long, straight haulageway and to estimate the damage potential inherent in production blasts fired in close proximity to underground structures. Commercial pressure gages with a flat response to 1 kHz were used with an FM tape recorder to record the overpressures from one dynamite and two AN-FO (ammonium nitrate-fuel oil), 500-msec production blasts having zero-delay charge weights of about 75 lb (34 kg). The recorded waveforms from the underground blasts (1) were more complex than the typical free-air wave, (2) were of longer duration, and (3) had numerous secondary arrivals due to reflections from the ribs and roof. The waveforms showed that the zero-delay charges produced the only high overpressures. First pulse peak overpressures from the blasts ranged from 0.10 lb/in2 (6.9 X 102 N/m2) at a distance of 471.1 ft (144 m) to a maximum of 1.76 lb/in2 (121.3 X 102 N/m2) at 191,7 ft (58.4m) from the blasts. An analysis of variance of the first pulse overpressures from the three White Pine blasts showed that no statistically significant difference existed among the overpressure levels from the dynamite and AN-FO blasts and that a single equation P = 4.9 x 103 (D /W1 / 3) 2 .15, where P = overpressure in pounds/inch2, D = d-stance from the blast in feet, and W = zero-delay charge weight in pounds, could be used to describe the falloff of overpressure with distance.

Jan 1, 1971

The head loss data for coal slurries over a range of concentrations and velocities and the laboratory screen analysis were selected as areas for investigation in the data analysis performed. The analysis resulted in the following: (1) Size distributions for the coal used in the horizontal pipeline tests were fitted to the Rosin - Rammler distribution function. Each of the fits was significant. Corresponding Rosin - Rammler parameters were obtained which were introduced into the regression analysis. (2) A regression equation was obtained which predicts the slurry head loss of 1-inch by 0 coal slurries ranging in volumetric concentration from 20 to 40 percent and line velocities from 1 to 14 feet per second as a function of the square of velocity. The addition of the term for concentration in the regression equation did not contribute significantly c head loss.

Jan 1, 1972

By I. F. Avery

The productive capacity of natural gasoline and cycling plants in the United States on January 1, 1956, was 46.4 million gallons per day, according to the Bureau of Mines r biennial survey. This represented an increase of 7.5 million gallons per day during the 2-year period since the last survey. In the previous 2-year period, capacity had increased 4.8 million gallons per day. The total number of plants increased from 535 on January 1, 1954, to 600 on January 1, 1956. The number of operating plants increased from 521 to 571. The major increases in capacity took place in Texas, Louisiana, New Mexico, and Oklahoma, with the absorption-type plants continuing to account for most of the new construction. All types of plants showed construction gains with the exception of charcoal which showed no change.

Jan 1, 1957

By Arthur M. Hartstein

The Bureau of Mines, through contract with Ultrasystems, Inc., obtained data on the oxidative degradative behavior of a number of materials used in coal mines. Tests were performed using a stagnation burner arrangement. Materials examined included those used in typical coal mining operations such as (1) polyvinyl chloride-containing materials. (2) neoprene compositions, (3) rigid foams (urethanes/isocyanates), (4) miscellaneous materials (including jute, fiber glass, and polyethylene), (5) coal, (6) fluids (phosphate esters, organic esters, oil-water emulsions), and (7) composites. The composite comprised a mixture of a phosphate ester fluid with (1) coal, (2) a representative polyvinyl chloride sample, or (3) a neoprene-type composition. A number of decomposition products are identified that could represent a potential health hazard to miners including HC1, CO, SO2 and H2S, if they were generated to exceed toxic levels.

Jan 1, 1974

By T. J. Driscoll

In this Bureau of Mines investigation, the electrochemical polarization behavior of Fe and Fe-1BCr has been characterized in rigorously controlled 1[N] H2S04 solutions stirred with oxygen or an inert gas. Samples that under-went various levels of corrosion or passivation were examined using Auger electron spectroscopy (AES) and ion sputtering. Passivation of iron occurred at a potential of approximately 0.6 volt (1) in poorly stirred, oxygen-saturated solutions for forward polarization (scanning from cathodic to anodic potentials); (2) in pH-adjusted (increased), well-stirred, oxygen-saturated solutions for forward polarization; and (3) in well~ and poorly stirred, oxygen-and helium-saturated solutions for reverse polarization. Passivation of Fe-18Cr occurred at a potential of approximately -0.1 volt in helium-, nitrogen-, and oxygen-saturated solutions for all cases of forward polarization and most cases of reverse polarization. Elemental depth profiles obtained from AES sputtering measurements indicated that films or adsorbed species were present on iron samples in solution subjected to open-circuit, active, and transpassive corrosion, cathodic reduction, and passivation. This conclusion was reached by considering the distribution of the solution species, primarily sulfur, in the films, which were composed primarily of iron and oxygen. Sulfur was present throughout the films on actively corroding samples, in the outer regions of films of passive and transpassive samples, and on the film surfaces of open-circuit and cathodically reduced samples. For Fe-18Cr, sulfur was found on the surfaces of films on passive samples only, indicating that only the passive samples had films on their surfaces in solution. The films on electropolished and passive Fe-1BCr samples had the largest chromium concentrations, estimated to be approximately 45 at. pct, with less chromium in films of cathodically reduced, active, and open-circuit samples, in that order.

Jan 1, 1979

By A. B. Hooker, L. C. IlsLey

 Previous publications relating to permissible methane detectors covered investigations of the detectors from January 1922 to January 1,1937. All of these detectors are obsolete, or the designs have been modified under extensions of the original approvals. This report covers the investigations of detectors since January 1, 1937, including the present permissibility requirements as to design and performance and a brief description of each detector.

Apr 1, 1942

By Allen D. Look, Alan A. Sharp

"Churn drills for blast-hole drilling are important to the operation of most open-pit metal mines, but certain hazards are created through their use that cause fatal and nonfatal accidents.2/ The purpose of this circular is to present a code of safe practice prepared and followed at a large Arizona open-pit copper mine, where safety is recognized as a definite operating problem. Such a code, based upon a thorough study of available published information as well as practical experience gained from accidents and near accidents, is the result of considerable effort and monetary expenditure. It is hoped that other operations using churn drills may benefit by the code presented, either in comparison with existing rules or in the preparation of new operating instructions.The code presented is in use at the Morenci Branch of the Phelps Dodge Corn., Morenci, Ariz. Similar codes are used at the New Cornelia Branch, Ajo, Ariz., and in the waste-pit operation at the United Verde Branch, Jerome, Ariz.The authors gratefully acknowledge the cooperation of the Phelps Dodge Corp., whose personnel made: possible the collection of information included in this circular. Special acknowledgment is due Paul Simmons, safety engineer, and 3. U. Larsen, general drilling and blasting foreman, Morenci Branch, Morenci, Ariz.The importance of churn drills in Arizona mining is apparent when it is realized that at all the open-pit copper mines blast holes are drilled with this equipment. At Morenci, approximately 98 percent of the ground is broken by primary blasting of churn-drill holes.There has been a growing tendency in Arizona's copper-mining industry to change from underground to open-pit mining, with consequent increase in the use of churn-drill blast holes for primary blasting.3/Thirty-three churn drills are in use at Morenci for blast-hole drilling. The drills operate with 440-volt alternating current, and trailing drill cables, in 500-foot sections, connect with the portable drill transformer station.4/ Three Diesel-driven churn drills for drilling prospect holes also are in use. About 25 churn-drill shifts are operated currently on a three-shift basis. Ordinarily, a two-man crew is assigned to each drill; however, with prospect-drill crews a third man is added to handle the sampling.Benches are carried at a uniform height of 50 feet. Churn-drill holes are 9 or 12 inches in diameter and about 60 feet deep. The holes are 18 feet apart in hard waste and 21 feet in soft waste and ore, with toes from 11 to 13 yards at the shovel grade. Both the hole spacing and the toe have been increased gradually, until they are now 2 yards longer than in 1940. The average ground broken per hole is 3,500 tons, or 60 tons of ore per foot of hole drilled. The holes are drilled 10 feet below the bench to avoid leaving hard bottom, which requires secondary drilling and blasting.Starting with a 12-inch casing, the prospect holes average 1,200 to 1,500 feet in depth and terminate with 6-inch casing; the deepest hole drilled to date went to 1,735 feet.In addition, churn-drills are used at Morenci to drill blast holes in the silica pit, limestone quarry, and the tailings dam. Other irregular applications are the drilling of holes to set trolley roles and for concrete piling in building foundations."

Jan 1, 1950

By John C. Edwards

Carbon monoxide (CO) sensors are used in mine fire early-warning systems. Experiments were conducted by the U.S. Bureau of Mines with six diffusion-type CO sensors to determine their response to a reference CO concentration under both static and dynamic flow conditions. Static experiments were conducted with 0.5 L/min flow of 16 ppm CO in N2 through 8-and 12-L chambers. Dynamic flow experiments were conducted in two environmental chambers: One had directional flow capability of 1 m/s, and the second provided moderately nondirectional flow as high as 1.8 m/s. Reference CO concentrations of 13.5 to 19 ppm in air were used for the dynamic experiments. The results of the static experiments demonstrated that the sensors consistently underestimated the reference gas concentration. The dynamic experiment results showed the sensors provided reasonable agreement with the reference gas concentration when directional flow effects were not considered. Directional flow effects were evaluated for two sensors. One of the sensors showed a strong dependence upon the relative orientation of the diffusion tube with respect to flow direction. The second sensor did not show a dependence upon flow direction. The sensors' directional flow effect is significant for their proper in-mine utilization.

Jan 1, 2010

By Marilyn Biviano

This analysis was conducted in response to concerns raised by the Chairman of the Energy and Commerce Committee of the House of Representatives regarding the potential impacts on automobile production, GNP and employment resulting from embargoing south African supplies of the platinum-group metals, platinum and rhodium. This analysis should be considered an addendum to the recently released study in which the direct economic costs I of a U.S. embargo on selected South African strategic and critical materials are estimated. The estimated GNP and employment impacts result when a mineral shortage reduces domestic industrial production and are in addition to the direct costs estimated in the earlier study. The direct cost to this nation resulting from a decision to embargo six south African strategic and critical minerals was estimated at $1.85 billion per year during the 1988-1992 time frame of the study. The estimated direct costs include the costs to U.S. consumers resulting from higher strategic mineral prices, lower mineral consumption, and the cost of developing higher cost domestic mineral resources. A large proportion of the costs result from the shortage of the two metals: platinum and rhodium. The average direct annual cost of embargoing is estimated at about $1.4 billion for platinum and $384 million for rhodium.2

Jan 1, 1988

By H. V. Makar

Ferrous fractions recovered from urban refuse were tested by the U.S. Bureau of Mines, U.S. Department of the Interior, to assess their character, composition, and response to detinning. This research was conducted as part of the Bureau's efforts to conserve mineral resources through recycling. Results from laboratory and pilot tests established the technical feasibility of detinning scrap recovered from household refuse. Detinned products containing less than 0.03 percent residual tin were produced. Concentrations of other residual elements were determined and compared with those in existing commercial scrap and with proposed specifications. Studies were extended to include evaluations under commercial conditions. Preliminary tests on 5-1/2 short tons of ferrous fractions revealed the need for adequate shredding to assure optimum metal-caustic contact and minimize retention of tin-bearing rinse solution in the final baled product. The washed metal product contained 0.06 percent residual tin. Subsequent melt tests showed a yield of 91.4 percent. Based on these studies, full-scale commercial demonstrations showed that detinned bales equivalent to No. 1 bundle quality could be produced in carload quantities. Up to 5 pounds of tin per gross ton of scrap is con-currently recovered during the detinning process.

Jan 1, 1979

By Robert F. Chaiken

A novel approach to eliminating environmental and public safety hazards that are associated with fires in abandoned coal mines and waste banks involves the use of in situ combustion technology developed by the Federal Bureau of Mines to accelerate the burning of the wasted coals in place. This technology would be used under exhaust ventilation control conditions that would allow for total management of the hot gases produced. Combustion stoichiometries would be optimized to minimize unburnt combustibles and to maximize the heat content of the gas products, which will be exhausted at one or more fan locations. When necessary, scrubber systems would be employed to remove air pollutants, such as sulfur dioxide; heat utilization systems (process heat, steam, and electricity) would also be employed to offset operational costs. Ultimately, complete burnout would solve the fire and acid water formation problems of the abandoned coal mine or waste bank. Pertinent technical data for burnout control are derived and discussed in terms of the important material and operational parameters. In general, it is believed feasible to operate a burnout system in an existing abandoned mine or waste bank fire at thermal power levels in the range of 10 to 100 Mw, and at exhaust gas temperatures of 1,000° C (1,830° F).

Jan 1, 1980

By Charles L. Kimbell

For 1991, the aggregate value of world international export trade in mineral commodities was roughly estimated at $685 billion in current 1991 dollars. The estimated level was about 6 % higher than that for 1990, but still more than 3 % below the record high set in 1980, and the year was the fifth in a row in which the value of exported minerals advanced. Table 8 provides a data series for the estimated value of world export trade in all mineral commodities from 1979 through 1991, as well as a breakdown of this total into fuel and non fuel commodities. The data shown are based on the historically more traditional and realistic (from the viewpoint of data availability) practice of reporting trade values for the year before the year of review. Despite the considerable increase in the dollar value of mineral commodity exports, their share of total export merchandise trade declined to 19.1 % in 1990 from 19.7% in 1989. At 19.1 %, this share was very near the recent year record low of 19.0% reached in 1988. Comparable 1991 figures were not available in time for inclusion here, but it is expected that the mineral commodity share of the total will be little altered from that of 1990.

Jan 1, 1993

By A. F. Colombo

In an effort to maintain an adequate supply of iron to meet national economic and strategic needs, the Bureau of Mines, U.S. Department of the Interior, is conducting research on methods for beneficiating the oxidized taconite resources located on the western Mesabi range in Minnesota, thus expanding domestic iron ore reserves. The selective flocculation and cationic flotation process was investigated in a pilot plant using an ore feed rate of 410 kg/hr (900 1b/hr) and 88 percent recycled water. Lime and a cationic flocculant were used to clarify the waste slurries treated in the water reclamation circuit. An oxidized taconite assaying approximately 36 percent Fe yielded concentrates averaging 63.5 percent Fe and 4.3 percent SiO2 and having an average iron recovery of 84.4 percent. The estimated reagent cost per tonne of concentrate was approximately $1.10. In an attempt to recover more of the iron lost in the flotation tailing, wet high-intensity magnetic (WHIM) separation was incorporated in the pilot plant circuit. The flotation concentrate grades obtained from beneficiation circuits with and without WHIM scavenging were similar, but when WHIM separation was used the overall iron recovery was increased by 2 to 9.5 percent, depending on the iron assay of the flotation tailing.

Jan 1, 1978