Search Documents

By Connie S. Musulin

The Bureau of Mines conducted an experiment at Exxon Mineral Co.'s Buffalo Shaft Operation to determine the time required for radon concentrations to return to a base average after fan shutdowns. Shutdown times ranging from 5 min to 16 hr were evaluated. An equation was derived to calculate a ratio that determines the time required for the radon concentration to return to the average level that existed in the mine prior to shutdown. For fan shutdowns of 15 min or more, underground personnel should be evacuated to areas with natural downcast ventilation. For shutdowns of less than 1 hr, personnel should not return to the working area until the elapsed time is four times the shutdown, or until the working area is resampled and found safe. If the mine is not in production during weekends, the downcast fans can be turned off .from midnight Friday until 4 p.m. Sunday, and the radon daughter concentration should be below 1 WL throughout the mine by the start of the shift Monday. This fan shutdown would conserve energy and save the mining company an estimated $21,000 each year.

Jan 1, 1982

By D. Hurrington

For severlrl 1e1.rs the Bureau of Mines has studied dust and ventili in metal mines a.s a.tfeoting the hea.l th, safety, and efficiency of underground workers. From its beginning this work haa been directed by G, s. Rice, chief mining engineer, A. cooperative agreement was ma.de in 1915 with the u. s. Publi Health Service; since that time tield obmervations 1n metal mines in Arizona, California, Idaho, Montana, Michigan and Nevada, and less extensive observation, in several other States have been made by mining engineers of the U, s. Bureau of Mines, and doctors of the u. s. Pu.blic Heal.th Service. Most of the analyt:J:eal work has been done by chemists, petrographers, and other specialists in the Pittsburgb station ot the Bureau of Mines, Numerous articles have been printed by the otticial and the technical press on this important in•estigation; 1n response to the need for a btiet bibliography of this literature. it has been compiled to facilitate accp1,intance with published data ot1. the subject,

Jul 1, 1922

By Peter F. Steidl

Seven degasification wells have been completed in the Pittsburgh coalbed at the new Emerald mine near Waynesburg, Pa. Funding was provided by the Bureau of Mines to perform stimulation treatments on five of the wells, to show that this is a feasible and economical means of degasifying part of a coalbed. The seven wells ranged in depth from 590 to 910 feet. Stimulation treatments used 25,260 to 42,660 gallons of foam and 7,400 to 12,800 pounds of 20/40-mesh prop sand. Pumping rates were 10.8 to 11.6 bbl/min and treating pressures were from 1,050 to 1,600 psig. On the day following stimulation, gas production ranged from a few hundred cubic feet per day to more than 100,000 cu ft/day.

Jan 1, 1978

By J. E. Wilson, J. D. Davis, C. R. Holmes

 The Bureau of Mines-American Gas Association (BM-AGA) method5/ has been used in surveying the carbonizing properties of American coals and, to date, in testing coals from 43 beds. The results in this report apply only to tests in the 18-inch retort at 800°, 900°, and 1,000° C. on coals from 32 beds. Table 1 gives the proximate and ultimate analyses of these coals and the name and location of mines. Coals from Pennsylvania, Virginia, West Virginia, Kentucky, Indiana, and Washington are considered. Seven of the coals are of low-volatile, four of medium-volatile, and twenty-one of high-volatile bituminous rank. One of the high-volatile coals (No. 45) is of high-volatile C rank, whereas all the others are of high-volatile A rank.

Mar 1, 1943

By R. V. Ramani, P. M. T. White, D. Sutton

5.1 Incorporation with the Master Design Simulator Figure 1 diagrammatically illustrates the interaction between the various sub-systems that go to make up the total Master Design Simulator. As a total system, all sub-systems will be scheduled as needed by the controlling program. The data require¬ments for each will be made available either by providing common storage in core or by outputting data to external storage devices such as magnetic tape, disk, drum, etc. The incorporation of the Geology and Reserves sub-system into the total system involves the establishment of an interface through which data may be readily dissemminated in either direction. This interface will be provided by a geological data library in which all information available from the sub-system is stored and can be readily accessed by the main program and/or other sub-systems. In Figure 7, the information flow between the Geology and Reserves sub¬system and other sub-systems is shown. 5.2 Independent Function Geology and Reserves sub-system is capable of functioning as an independent unit or in direct communication with another sub¬system. This is possible by either continued use of the data library or by redirecting output to other peripheral devices separate from the total system libraries. (Figure 8).

Jan 1, 1974

By R. V. Ramani, C. B. Manula, A. Owili-Eger

All the input data required to operate the ventilation simulator except the title, are entered with I10 or F1O.O formats. The title is entered with (18A4) format. The floating points are designated by (FP) and the integers by (INT)

Jan 1, 1975

1. In 2003, a total of 258 metal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Metal mines were the smallest mining sector, comprising 1.8% of all mining operations.1 • Gold mines comprised 44.2% (n = 114) of all metal mining operations. Other common types of metal mines were iron ore (n = 29; 11.2%), copper ore (n = 28; 10.9%), and lead and/or zinc ore (n = 21; 8.1%). • Nevada had the largest number of metal mines (n = 48; 18.6%) followed by Alaska (n = 29; 11.2%).

Feb 1, 2005

By David S. Yantek

A-weighted sound levels around vibrating screens in coal preparation plants often exceed 90 dB(A). The National Institute for Occupational Safety and Health (NIOSH) is actively developing noise controls to reduce noise generated by horizontal vibrating screens. A 121-microphone, 3.5-meter-diameter array was used to perform beamforming to determine locations of significant noise radiation on the screen. Below about 1 kHz, the screen body was found to be the most significant noise source. The beamforming contour maps showed several key locations on the sides of the screen and the feedbox are the most significant contributors. Operating deflection shape (ODS) analysis was used to examine the screen behavior under actual operating conditions. This information is helpful in determining how to modify the screen body to reduce the noise radiated by the screen below 1 kHz. The analysis showed modal vibration patterns on the sides and feed box were the main contributors to noise. The results show several areas on the screen sides and feedbox that can be modified to reduce noise.

Jan 1, 2009

By W. F. Marshall

The Bureau of Mines conducted a series of experiments to determine the influence of exhaust rebreathing on emissions from various gasoline and diesel engines. Tests were conducted that simulated operation of engines in nonventilated spaces as well as in spaces with partially restricted ventilation. Results of these tests showed that exhaust rebreathing can have a marked effect on exhaust emissions and thus on the composition of the air in the working space. For the case of restricted ventilation, unacceptably high (greater than 50 ppm) levels of CO in the air of the working space resulted from exhaust rebreathing rates as low as 8 pct exhaust in the engine's intake. Operation in a nonventilated space resulted in highly critical CO levels (fatal in a few minutes) at times corresponding to 1 to 3 pounds of fuel consumed per 1,000 cu ft of space. Tests involving spaces of various sizes showed that volume of the air space [per se] is not important--the primary variable is fuel consumed per unit volume of air space.

Jan 1, 1973

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

All output is saved in the file MFIRE OUT m the di¬rectory and on the disk containing the program The file can be inspected with a text processor and sent to a print¬er, if needed CONTENTS OF OUTPUT FILE The comment lines, reference temperature, air densi¬ty, a table of the units of measure for the results, and the average values are shown at the beginning of MFIRE OUT All input data will be shown in the output file if LOUT on Control line number 1 is _<-1 For each contamination source, a new branch will automatically be setup The new airway and junction ID numbers will not interfere with the original numbering scheme of the data file Next are the results of the selected simulation(s) in the following order network balancing, network balancing considering temperatures, transient-state modeling, and altered equilibrium due to fire and distribution of the contaminants. Depending upon the contents of the data file, and the simulation selected, attention, warning, and error message will be shown at locations where calculations resulted in unusual conditions

Jan 1, 1990

To more rapidly and economically prepare solutions for chemical analysis, of a wide range of ores, slags, minerals, and metals. Approach A Simple pressure-dissolution system was devised using an inexpensive, heavy wall plastic bottle containing a sample in an acid medium. Using the technique, a complex silicate sample can be dissolved in less than 1 hour. How It Works A weighed portion of a sample, ground to minus 100-mesh, is placed into a polycarbonate or polysulfone plastic bottle. A mixture of hydrochloric acid, nitric acid, and hydrofluoric acid then is added. The bottle threads are wrapped with a layer of Teflon tape to prevent leakage, and the bottle cap is screwed on tightly. The sealed bottle is placed in a balling water bath. In the hot water, the plastic bottle acts as a pressure vessel to contain the pressure generated inside it. This technique should only be used by trained experienced people who are familiar with the hazards of hot acids under pressure. After being cooled in cold water, the resulting solution is brought to the final volume by adding 1.5 weight-percent boric acid solution to the bottle. The cap is replaced, and the bottle and solution is reheated. Precipitated fluorides, as well as any residue, are dissolved by the fluoride-boric acid reaction. The resulting clear solution then is suitable for spectro-photometric examination or other analysis.

Jan 1, 1980

By R. Barany

The heat of formation at 298.15 ° K of muscovite was determined by solution calorimetry . The value obtained for the heat of formation from the elements was -1,421.2 ± 1.3 kcal / mole , and the value for the heat of formation from the oxides was -55.9 ± 1.3 kcal /mole .

Jan 1, 1964

By Maria I. De Rosa

Table 28 and figure 10 show the number of fires and fire injuries for coal preparation plants by state during 1990-1999. Table 28 also shows the risk rates, employees&apos; working hours, and lost workdays by state. For coal preparation plants, 91 fires occurred in 1 1 states during 1990- 1999. Twenty-three of those fires caused 25 injuries (the yearly average was 9.1 fires and 2.5 injuries). Ten fires and eight injuries involved contractors. The Ewhr value was 24 1 x 10&apos; hr (Irr = 0.02 l), and the LWD value was 198. Pennsylvania had the most fires (24 fires and 4 injuries), whereas West Virginia (22 fires and 7 injuries) and Kentucky (22 fires and 7 injuries) had the most fire injuries. Among these states, Kentucky had the highest injury risk rate value (Irr = 0.025). Table 29, partly illustrated in figure 11, shows the number of fires, fire injuries, risk rates, employees&apos; working hours, and lost workdays by time period. The number of fires decreased during most of the periods (an increase is seen only during the last period). The number of fire injuries show a decrease followed by an increase during the periods, accompanied by a decline in employees&apos; working hours throughout the periods. The Irr values follow patterns similar to those shown by the injury values (see table 29 and figure 11). Tables 30-35 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 12 shows the major variables during 1990-1999. Table 36 shows the fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX E EQUIPMENT USED FOR FIELD TESTING OF MINE SEALING SYSTEM I. Drilling Operation - Equipment supplied by local drilling contractor 1. Mobile drill rig. 2. Flat bed truck, containing 20 lengths of drill pipe. 3. Auxiliary compressor. 4. Pickup truck for small parts and supply of diesel fuel. 5. Bulldozer. 6. Water supply, in this case the nearby stream. 7. Supply of casing, positioned next to the drill rig. 8. Ready mixed cement grout. 9. Drill bits, stabilizer units, cutting and welding equipment, other miscellaneous tools and supplies. II. Sonar Probing Operation 1. 25 foot tower with pulley mounted atop. - FMA 2. Electric winch with 100 feet of 1/4-inch cable, Model No. 100A, City Engineering Co. , Indianapolis, Indiana. 3. 400 feet of 1-1/2-inch-diameter aluminum pipe with alignment holes and coupling grooves. - FMA*

Jan 1, 1973

By D. H. Baker

These investigations were conducted to determine the feasibility of molten salt electrorefining of zirconium scrap, offgrade sponge, and alloys under contract number AT(11-1)-475 between the Atomic Energy Commission and the Federal Bureau of Mines. Offgrade zirconium sponge having a Brinell hardness of 169 can be refined by this technique to produce metal having, consistently, a Brinell hardness of less than 90. Also, zirconium alloy scrap, approximating zircaloy-2 in composition, can be refined to recover zirconium metal with a Brinell hardness of less than 100 that is essentially free of the major alloying elements. Analysis showed that the quantities of these elements were decreased as follows: iron from 0.27 to 0.002, tin from 1.36 to 0.001, nickel from 0.02 to 0.001, and chromium from 0.12 to 0.002 percent.

Jan 1, 1961

By L. W. Brandt

As part of its objective to expand the body of mineral information as a basis for new technology, the Bureau of Mines conducted research on the fundamental behavior exhibited by phosphate clay waste in settling ponds. A semiempirical equation used to describe the compaction of ceramic powders in a single-acting die was applied to aqueous phosphatic clay waste and attapulgite slurries. This equation, [*V = a1 e ?k1/P + a2e ? k2/P] was found to describe the compaction of an attapulgite gel and a phosphate slime gel by a moving screen. [*V] is the ratio of the compaction achieved at a given pressure, P, to the compaction achieved at a pres-sure sufficient to remove all space between particles. The constant al represents the fraction of compaction achieved at low pressure by rearrangement of floes to higher packing density, and a2 represents the fraction of compaction achieved at higher pressure resulting from removal of voids within floes. K1 and K2 are constants determined from the experimental data. Both the low-pressure and high-pressure compaction mechanisms were observed in the compaction of the clays. These two compaction mechanisms offer an explanation for the observation that impounded slimes initially dewater rapidly and then dewater at a much slower rate.

Jan 1, 1982

By Thomas V. Falkie, R. Venkataramani

1. Summary This investigation is concerned with description of the loading function at the underground coal face, and the identification of varia¬bles - geological, geometric, mechanical, and operational - that affect the loading function. The immediate objective of this work was to provide information for operations-research studies as applied to underground coal mining, and the broad objective was to provide guide¬lines for planning and equipment selection in underground coal mining. The loading function was expressed as -a statistically-developed linear mathematical model. Originally, fifteen independent variables were considered which potentially could have influenced the loading function. These variables were constructed on the basis of measurable or estima¬ble geometric and geological properties at the working face, mechanical characteristics of the mining machine, and certain operational proce¬dures of mining. The original model explained 64.0 percent of the experimental variation. The final condensed model explained 54.1 percent of the experimental variation in terms of only five indepen¬dent variables, namely: 1. Ratio: width of cut/total width of cutter 2. Ratio: height of cut/diameter of cutter 3. Total horsepower of cutter-drive motors 4. Rotation speed (RPM) of cutter 5,. A subjective estimate of machine quality and operator skill Certain limitations were found to exist in the evaluation of the variables. Principle among these limitations was the impossibility of precise measurement of tonnage loaded in certain instances.

Jan 1, 1972

By L. B. Pankratz

The Bureau of Mines conducted heat-content measurements above 298.15° K for dehydrated analcite (NaAISi2O6) to 1,000°K, kaliophilite (KA1Si04) to 1,800° K, and leucite (KAlSi206) to 1,800° K. Heat content and entropy increments were tabulated, and the heat content data, were given in equation form. A first order transition was noted for kaliophilite near 810° K with a heat absorption of 160 cal/mole. Leucite had a second order transition which became complete near 955° K. In this transition a crystal change occurred from tetragonal (low-temperature form) to cubic (high-temperature form).

Jan 1, 1968

By J. M. Stuve

This Bureau of Mines investigation measured the low-temperature heat capacities of FeOC1(c) and FeC13(c) in the temperature ranges of 6 to 305 K and 4.6 to 300 K, respectively. The standard entropies (S°, 298.15 K) of FeOCl(c) and FeC13(c) were derived as 19.73±0.03 cal/deg-mole and 35.33±0.07 cal/deg-mole. A large lambda transition was observed in the heat capacity of FeC13(c) at 8.4 K. The standard enthalpy of formation (?H°f, 298.15 K) of FeOC1(c) was determined to be -98.23±0.22 kcal/mole by HC1 solution calorimetry. High-temperature enthalpy measurements (H-H298.15) of FeOC1(c) were determined to 700 K by precision drop calorimetry. Standard thermodynamic formation data and related functions were tabulated at various temperatures for FeOC1(c) and FeC13(c).

Jan 1, 1980

By Gene Asai

Properties obtained for columbium carbide-carbon castings ranging in car-bon content from 12 to 17 weight-percent were compared with those of hot-pressed composites of similar composition. The properties were oxidation resistance in static air between 500° and 700° C, linear thermal expansion between 20° and 2,400° C, electrical resistivity between 20° and 1,500° C; microhardness between 20° and 1,500° C, and modulus of rupture between 1,300° and 1,800° C. CbC-C castings differed markedly from hot-pressed material with respect to microstructure, electrical resistivity, and modulus of rupture, but behaved quite similarly with respect to oxidation resistance, thermal expansion, and hot hardness. In oxidation resistance, thermal expansion, and hot hardness both materials were independent of carbon content. Both castings and hot-pressed composites oxidize rapidly in air above 600° C, have thermal expansion coefficients very similar to columbium metal, and the logarithm of the hardness decreases linearly with increasing temperature. The microstructures of hot-pressed composites contained varying amounts of graphite in a CbC matrix but did not contain significant amounts of a eutectic structure present in all castings, nor did they contain graphite needles which were present in the hypereutectic castings. The higher electrical resistivity of hypereutectic castings over hypereutectic hot pressings was attributed to the presence of highly oriented graphite needles in the castings. The modulus of rupture of castings was 1-1/2 to 2 times that of hot-pressed composites. Both materials displayed bend ductility above 1,800° C.

Jan 1, 1971