Search Documents

By Richard F. Hewlett

This report describes a comparison of methods for computing grade and tonnage of ore, leach, and waste material for a mined-out portion of the Silver Bell Oxide porphyry copper deposit, and these computed values are compared with the actual tonnage of these classes of material produced during mining operations. Comparisons with production records have been made by using both exploration drill-hole assays and development blast-hole assays. The polygonal method is the most accurate for this deposit, because it more closely represents the lateral mineral distribution in the deposit. This is demonstrated by plots of the total-copper assay distributions of the development blast-hole assays for a specific bench. The investigation also shows that the smaller vertical assay interval (based on a 5-foot vertical churn-drill-hole sample) yields a more accurate estimate of both grade and tonnage than the 40-foot composite assay interval (based on the average of eight 5-foot assay values). This can be attributed to the fact that selective mining within a bench can separate out much of the waste and leach material that is included as ore in the 40-foot composite assay computations.

Jan 1, 1970

By John T. Kuo

The miner's seismic source strength can be approximately estimated on the basis of a single force acting in an infinite medium. Because of the uncertain- ty involved in estimating the amount of conversion from mechanical energy to seismic energy, the source strength thus estimated may be in error by as much as a half-order of magnitude. Calculations of wave transmission must take into account geometrical spreading, dissipation of energy by internal friction, and energy partition due to reflection and refraction of waves impinging on inter- faces in the layered earth. Theoretically derived peak-to-peak particle velocities in microinches per second (PIPS) are given for two models ; viz: (i) 50-feet thick and (ii) 100- feet thick 4000 ft/sec layers with Q = 20, overlying a half-space of 10,000 ft/sec material with Q = 5O;for the cases .of a hammer blow and a timber impact, at the frequencies of 50 Hz and 100 Hz. Comparison of the theoretically derived peak-to-peak particle velocity with experimental data taken at the Copper Queen Mine indicates that the theoretical particle velocity may be overestimated. A discussion of the distortion of seismic wavefronts by mine tunnels indicates that it is unfavorable to use a seismic source impact on the floor of the tunnel, since deceptive delays in arrival time are liable to occur at the surface. A program of parallel theoretical and experimental work is required to clarify uncertainties still associated with the nature and strength of the miner's seismic source signal which cannot be resolved within the approximations of this work. Its major components include theoretical investigations of the (1) Wave diffraction and scattering of an impact source on a face of a cylindrical cavity. (2) Impact of an elastic object on an elastic medium.

Jan 1, 1974

By H. B. Brunot

A complete list of permissible mine equipment, tested and approved by the Bureau of Mines previous to January 1, 1947, was published as Information Circular 7432.2/ A list of permissible mine equipment tested and approved by the Bureau of Mines during the calendar years 1947, 1948, and 1949 was published as Information Circular 7569. The present list supplements Information Circulars 7432 and 7569 and includes all of 'the equipment approved during the calendar year 1950. Information Circular 7465, which included a list of permissible mine equipment tested and approved by the Bureau of Mines during the calendar year 1947 therefore is superseded.

Jan 1, 1951

By S. J. Broderick

"INTRODUCTION Dark soils are commonly believed to be better for agricultural purposes than light-color soils. Much of this feeling may be purely psychological, as many persons have unconsciously acquired the habit of associating richness of soil with color light soils, however, may be just as rich in humus and plant foods as the best of the dark soils. A dis-cussion of the manifold attributes that play an important role in soil technology is beyond the scope of this paper, but the color factor will be considered, as it has a particular bearing on some field experiments using coal-mine waste as a darkening medium.It has been established that dark soils absorb more of the sun's radiation, consequently are maintained at a higher temperature than light soils. This physical principle is applied in our daily lives in the choice of clothing. White clotnes in summer are cooler than dark ones. Conversely, dark clothes in winter are warmer than light-color clothing. A decided advantage of dark soils over light soils is the higher average temperature of the former, resulting in an earlier maturing crop. This advance of the maturing season may range from a few days to a month, depending on such factors as climate, crop, and degree of color of the soil. It has been reported that in parts of Russia where the growing season is short, perhaps comparable to that in Pennsylvania and. New York, cotton has been grown successfully on soils originally of light color, but darkened with coal, dusts. The growth of cotton is, accordingly, speeded up a full month. 3/"

May 1, 1940

Spectrochemical methods were developed to determine beryllium in the concentration range 0.0015 to 4.0 percent in siliceous mineral beneficiation products. Two methods are described. They are (1) a fusion-pellet-spark procedure (spark method) and (2) a sustaining alternating-current arc procedure (arc method). In the spark method the sample is fused with lithium tetra-borate and vanadium pentoxide. The resulting bead is crushed, mixed with powdered graphite, and briquetted. This is analyzed spectrographically using controlled high-voltage spark excitation. In the arc method the sample is diluted with germanium metal, graphite, and vanadium pentoxide. Weighed charges are packed into cupped graphite electrodes and subjected to excitation with a sustaining alternating-current arc. Vanadium serves as internal standard for both methods. Effects due to matrix variations in samples and standards are eliminated either by fusion with lithium tetraborate in the spark method or by dilution with germanium and graphite in the arc method. Beryllium determinations show deviations from accepted chemical values of approximately 5 and 8 percent for the spark and arc methods, respectively. Analyses can be made more rapidly by the arc procedure with a sacrifice in precision and accuracy. Either method can be applied to the determination of beryllium in silicate rocks.

Jan 1, 1962

By D. Montagna

The Kroll-Betterton process for debismuthizing lead is based on adding calcium and magnesium to impure molten bullion to form solid Ca-Mg-Bi inter-metallic compounds that float on the surface as drosses. Present practice in industry is to hand-skim off these drosses, often followed by hydraulic pressing to squeeze out some of the entrapped liquid lead. In an effort to develop an improved technique, the use of an argon-shrouded dipping centrifuge to perform the required phase separation was investigated. Centrifugation experiments demonstrated that the bismuth content of an impure bullion could be lowered from an initial 0.5 percent down to 0.03 percent with a lead recovery of 90 percent, which is comparable to lead recovery after hand skimming of drosses in commercial lead-debismuthizing operations. Centrifugation provides better control in removing drosses, faster operation with less oxidation and relatively little fuming, and recovery of a lead bullion that approaches commercial specifications.

Jan 1, 1972

By Stephen D. Cramer

The solubility of methane, carbon dioxide, and oxygen was measured in brines at temperatures from 0° to 300° as part of Federal Bureau of Mines research on the corrosion of metals in high-temperature geothermal and mineral processing environments. Solubilities were measured by the technique of extracting pure gas, dissolved at pressures where Henry's law was applicable, from known volumes of brine. The results were smoothed with respect to temperature. The solubility, expressed in terms of the Henry's law constant, reaches a maximum at temperatures ranging from 60° to 100° C for methane and oxygen, and from 160° to 170° C for carbon dioxide. The Henry's law constant increases, that is, gases are salted out of the brines, in the presence of dissolved salts. Salting-out coefficients are strongly dependent upon temperature. The temperature dependence of the Henry's law constant for geothermal brines is different from that for sodium chloride brines owing to the more complex chemistry of the geothermal brines. The solubility of oxygen and carbon dioxide in brines exposed to air saturated with water vapor and at a total pressure of 760 mm Hg is reported for temperatures from 0° C to the normal boiling point.

Jan 1, 1982

By E. L. Burwell

Application of the in situ recovery process to oil shale was tested during two field experiments near Rock Springs, Wyo. The results of these tests demonstrate that a self-sustaining combustion zone can be created in an oil shale body, that this zone can be moved through the oil shale, and that the process will produce shale oil. Evaluation of the combustion process by monitoring produced fluids for physical and chemical properties and volumes is described. The material and energy balance obtained is compared with a second evaluation based on extensive coring of the test area after the test was terminated. Several side results of the research are noted such as ground surface heating by underground burning and production of low-to medium-Btu gas during retorting.

Jan 1, 1973

By K. K. Kershner

The purpose of this investigation was to develop methods on a laboratory scale for recovering tin from metallurgical slime, Tin chlorides were volatilized using mixtures of hydrogen chloride and reducing gases, such as hydrogen, carbon monoxide, hydrogen sulfide, ethane, propane, and butane. Optimum conditions were found to be n mixture of 3:1 of hydrogen and hydrogen chloride at 475° C. Over 95 percent of the tin was volatilized as chlorides. Low temperatures and relatively rapid rates of reaction are distinct advantages of the chloride volatilization process. Research is being continued with various slimes and will be extended to tin ores, where the method offers interesting economic possibilities in comparison with current tin-smelting practice.

Jan 1, 1957

This report presents test results, data evaluations, and typical system performance expectations based on wireless electromagnetic propagation measurements performed in the MAGMA Copper Company's San Manuel mine near Tuscon, Arizona during March 30 through April 2 1981. In particular, and at the Bureau's request, this work was coordinated with testing of MF prototype vehicular radios being developed by A.R.F. Products, Inc. with USBM support under Contract H0308004 as part of a system to be marketed by Mine Safety Appliance Co. This testing also employed a prototype vehicular antenna developed by Terry S. Cory, P.E. with USBM upport under previous Contract P0382223. The work was performed under USBM contract J0308012, Propagation of EM Signals in Underground Metal/Non-metal Mines. The authors wish to thank Mr. Hank Seany, Manager of Mines and Mr. Bob Zerga, Mine Superintendent who so kindly arranged for the visit. Particular thanks are given to Mr. Al Metcalf who arranged the logistical details of our underground work, and whoa forward thinking program toward improving general mine communications at MAGMA provided the test-bed context for evaluation of the prototype equipment. The authors also wish to thank Benny Jiminez, Paul Ayala, Lorenzo De La Cruz, and Kent Billhartz for their day-by-day support of the testing. Mr. Jiminez's effort was instrumental in performing the testing, and he also provided a detailed understanding of the existing multi-level, multi-frequency trolleyphone system at MAGMA. the authors are also indebted to Dr. Larry Stolarczyk of A.R.F. for numerous detailed consultations on MF technology, and who was present and participated in the majority of the testing. 1.1 GENERAL BACKGROUND ON COPPER MINING AT MAGMA the San Manuel mine is the largest copper mine in the U.S., efficiently extracting copper and molybdenum sulfide from the low-grade San Manuel ore body.This ellipsoidal ore-shell body, with major workings located 2000-3000 feet mbelow the surface, has ore shell thickness varying between 100 and 1000 feet over a longitudinal extent of some 8000 feet, and with major & minor crossectional axes of about 5000 and 2500 feet respectively. The San Manuel mine operation employs in excess of 1000 men/shift with gross ore production between 60,000 and 70,000 tons/day. The mining operation employs the block caving technique; actively being implemented on three levels (2075,2375,2675 feet for haulage, and 2015,2315,2615 product/grizzly levels). The ore haulage is largely via D.C. trolley trains to four (3A,3B,3C,3D) product shafts for skipping to the surface. An additional three shafts at two locations are used to convey men, materials, and developmental rock extractions into and out of the mine. On each haulage level, the trains carry ore an average of two miles one-way from the ore raises to the dump points. 1.2 TOPOLOGICAL BRIEF OF THE HAULAGE LEVELS The 2375 level, on which all the testing was conducted, is illustrated in

Jan 1, 1981

By William P. Diamond

Ventilation has long been the primary means of controlling methane emissions in underground coal mines. However, as mining has progressed into gassier areas of U.S. coal basins, supplemental means of methane control have become of interest, if not a necessity, for continued safe and productive mining operations. This paper describes the history and technology of methane drainage in the United States and other countries. The methane drainage technology developed in European countries is a valuable resource since their longer history of mining has already forced mine operators to deal with methane emission problems only now being experienced in the United States. Methods for assessing the need for methane drainage and the data required for planning and implementing an appropriate system are reviewed. The effectiveness of the various technologies for reducing methane emissions underground and/or the in-place gas content of individual coalbeds is illustrated with case studies. In addition to the safety and productivity gains to be realized from methane drainage systems, the potential for commercialization of coalbed methane is discussed.

Jan 1, 1994

By D. N. Nilsen

The Bureau of Mines is investigating a method to recover Ni, Cu, and Co from low-grade domestic laterites through reduction roasting, leaching, sol-vent extraction, and electrowinning unit operations. The objective of this research is to develop processing technology that can convert low-grade domestic deposits containing critical metals into national reserves. As a part of this research, a solvent extraction system was investigated for the extraction of nickel and copper, followed by the separation and production of suitable electrolytes. Nickel and copper were coextracted from ammoniacal ammonium sulfate leach liquors (pH~9.5) with LIX 64N extractant in a laboratory-size mixer-settler continuous circuit. Three extraction stages resulted in >99-pct extraction of nickel, substantial copper extraction, and essentially no cobalt extraction from leach liquors. A crowd stage reduced the ammonia loading on the solvent by maximizing nickel loading. Residual ammonia was removed from the loaded solvent with a pH-controlled scrub. Nickel and copper loaded on the solvent were separated by selective stripping. Typical nickel strip circuit operation using electrolyte containing 90 grams per liter (g/l) Ni and 11.9 g/l H2S04 yielded >99.9 pct Ni stripped from the solvent in five stages. The copper loading on the recycled solvent was controlled in a copper strip stage using electrolyte containing 25 g/l Cu and 160 g/l H2S04,

Jan 1, 1981

By H. E. Peterson

This report revises an earlier publication by the Bureau of Mines on tungsten analytical procedures and expands the coverage by including appropriate procedures for the critical impurity elements that commonly occur in tungsten ores and concentrates (13).3 The basic methods described are not original, but many of the modifications to improve reliability and sensitivity were developed by the Bureau. Gravimetric and colorimetric methods currently used for the determination of tungsten in ores, mill tailings, and concentrates are described. Colorimetric procedures are preferred for low concentrations of tungsten, whereas either procedure is satisfactory for moderate concentrations. Conversely, a gravimetric method is preferred for the determination of tungsten in concentrates.

Jan 1, 1963

By Donald O. Capstick

A mineral survey of the 520-acre Quigg West Wilderness Study Area (MT-074-155) was conducted by the U.S. Bureau of Mines in 1986 at the request of the U.S. Bureau of Land Management in order to evaluate its identified mineral resources. The Wilderness Study Area is in Granite County in western Montana about 16 miles northwest of Phillipsburg and 27 mi les northeast of Hamilton, MT. Stony Mountain, a study area on lands administered by the U.S. Forest Service, is about 1 mile to the south-southwest and was studied concurrently. No mineral resources were identified in the Quigg West Wilderness Study Area, but high grade gold assays, as much as 1.24 ounce gold per ton, were obtained at the one prospect found. Samples from four workings contained significant gold; minor silver, molybdenum, and copper were also present. The prospect containing the narrow and discontinuous gold-bearing quartz vein straddles the south boundary of the Wilderness Study Area. The shear zone containing the vein projects toward the old Crescent mine, about 4.5 miles to the south, which shows a similar geologic structure.

Jan 1, 1987

Use controlled blasting techniques to reduce blast-produced overbreak damage to underground mine ribs and back for both safer working conditions and improvements in productivity. The Problem Blasting is used in metal and non-metal underground mine slopes, drifts and crosscuts to fracture rock to be excavated and further processed. Standard blasting also produces fractures in the rock beyond the desired excavation area. This is sometimes evident by rough surfaces, undercutting and other signs of excessive damage. This damage contributes to rockfalls in the mines, a major cause of injuries and fatalities, and equipment damage. A variety of controlled blasting techniques has been developed for civil engineering projects where long-term stability is essential. For several reasons, these methods arc not widely used in mining. For example, these methods incur additional costs and time; there is little need to maintain stable openings over long periods of lime; and there is the perception (hat corrective remedial techniques, such as rock bolting, are more practical. Basically the benefits of these methods are not demonstrably clear for application in underground mines.

Jan 1, 1991

By Charles A. Kumbe

"INTRODUCTION The Sullivan Mine was examined by Thomas L. Chapman, an engineer of the Bureau of Mines, in March 1943. Samples taken from the few mineralized exposures justified further investigation of the property. To determine whether extensive exploration of the property would be warranted, the Bureau did a small amount of trenching and underground work during April 1943, 3/ under Bureau project 1462.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its, primary objective the, more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratary project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurigical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests.The investigations of the and Metallurgical Branches of the Bureau, as reported in this paper, were supervised by J. Hedges, district engineer for Arizona, and S. R. Zimmerly, regional engineer for the Western Region, respectively."

Feb 1, 1947

By E. E. Maillot

In 1943, diamond drilling by the Bureau of Mines, comprising 11 holes which totaled 1,295.6 feet, showed that the pegmatite at Black Mountain consisted of shallow lenses in interbedded biotite-quartz-schist and impure quartzite. The average thickness of the pegmatite was 9.7 feet. Mineralization had a zonal arrangement. Beryl was most abundant near the footwall contact of the pegmatite. The average estimated beryl content of the pegmatite exposed at the surface was 0.81 percent, and the highest content of any pegmatite area was 1.75 percent. Other economic minerals were scrap mica, feldspar, spodumene, and lepidolite. Representative samples of the Black Mountain deposit failed to yield high-grade boryl concentrates by straight flotation owing to the presence of considerable spodumene. By employing heavy medium separation to remove the spodumene, 75.4 percent of the. BeO wan recovered in a flotation concentrate assaying 10.4 percent BeO.

Jan 1, 1949

By I. D. Shah

The copper-nickel ore of the Duluth Gabbro Complex in northeastern Minnesota is a large potential domestic resource of cobalt and platinum-group metals. However, because of the low grade of the primary metal values (0.5 pct Cu, 0.15 pct Ni), the private sector has assigned a relatively low priority to the development of technology for processing this ore, anticipating that mining probably would not begin until the mid-1990's. Furthermore, preliminary processing flowsheets considered by the mining companies centered on the primary metal values. As part of an effort to help provide the basis for technology to recover critical and strategic minerals from domestic resources the Bureau of Mines is investigating methods to recover all of the mineral values, in the Duluth Gabbro material, with particular attention to the byproduct critical minerals. A key step in this process is the removal of a relatively large amount of iron present in the bulk sulfide flotation concentrate to permit subsequent extraction of mineral values. This report describes a direct smelting method that removes most of the iron and produces a copper-nickel-cobalt matte, an intermediate product from which the metal values subsequently are separated. Copper, nickel, and cobalt grade and recovery data are presented for the direct smelting method. Test results showed that under certain conditions some of the mineral values reported to the slag, requiring slag cleaning to recover them.

Jan 1, 1983

By H. S. Chiang, Zhao. Y. F., G. C. Sun, S. S. Peng

"Chiang; H. S. West Virginia UniversityPeng, S. S. West Virginia UniversitySun, G. C. West Virginia UniversityZhao, Y. F.West Virginia UniversityDust sampling was performed in two longwall faces working in two separate seams. Instantaneous dust samples were measured by RAH's. for various locations In the longwall faces. Preliminary analysis of the data shows that in addition to the shearer's haulage speed, there are four major factors that influence the airborne dust distribution in longwall face areas: locations with respect to the position of the shearer's cutting, hardness of the materials, characteristics of water spray, and roof conditions. This paper presents the effects of those four parameters in detail.INTRODUCTIONA research project was initiated in September 1983 to measure and construct .a dust distribution map for the longwall face. During the first year, airborne dust samplings were performed in two longwall panels located in northern and southern West Virginia and working in the Pittsburgh and Eagle Seams, respectively. The physical parameters and equipment employed for both panels are 1 isled in Table 1. Figure 1 shows the detailed characteristics of the coal seams. Notice in both panels floor cutting was involved either to gain sufficient mining height or to reduce the adverse effects associated with a soft floor.The purpose of the research is to define the dust distribution at any instance in the longwall face area so that proper working positions can be determined and/or effective dust control techniques can be developed.This paper presents the partial results obtained during the first year."

Jan 1, 1988

By Paul R. Coyle, Anthony T. Iannacchione

A close look at the Loyalhanna Limestone of southwestern Pennsylvania reveals a complex structural environment. Most exposures of the Loyalhanna occur along Chestnut Ridge and LaurelHill within the Allegheny Mountain Section of the Appalachian Plateaus Province. Because the Loyalhanna is rated as a super-pavement aggregate by the Pennsylvania Department of Transportation and because of its proximity to the population centers of southwestern Pennsylvania, the Loyalhanna has been extensively mined along these prominent anticlinal structures. Geologic and engineering analyses were performed using gas well and core logs, outcrop examinations, underground observations, and mine maps. Strata exposures from both outcrops and quarries were used to construct geologic maps, stereo net, and rose diagram projections so that the Loyalhanna’s structural environment could be understood better. Many of these structural conditions cause ground control problems at local quarries. These problems ranged from small-to-moderate sized rock falls associated with roof jointing to pillar failures associated with dipping discontinuities. Stresses ranged from tensional on structural domes where weathering dominates, to high levels of compression within structural saddles. A greater understanding of these characteristics is a prerequisite to develop engineering controls, such as improved mine layouts, pillar sizes, etc., that lessen miner exposure to these hazards.