Search Documents

By Robert W. Smith

Computation of the thermodynamic properties of the reaction products in the deflagration of explosive gas mixtures has been a most valuable guide regarding the possible kinetic mechanisms of homogeneous combustion processes. Knowledge of the physically possible end states is indispensable for understanding observed deviations from equilibrium in heterogeneous combustion. However such information on dust flames is entirely lacking. To complement a Federal Bureau of Mines study of stationary graphite dust flames burning in pure oxygen,6/ this report gives examples, at atmospheric pressure and room temperature, of composition profiles in an idealized oxygen-dust flame, with both mass and enthalpy being preserved. Similar profiles can be obtained from the data of the paper for elevated temperature and pressure.

Jan 1, 1960

By P. C. Good

This Bureau of Mines report describes the preparation of phosphoric acid directly from phosphate ore, without prior beneficiation, in a small-scale, continuous process research unit, as part of an effort to improve minerals and metals recovery from domestic resources while minimizing environmental effects. Three phosphate-matrix samples, ranging in grade from 18.2 pct P20S5to 11.9 pct P205, were dry-fed at a rate of 1.82 kg/hr (4 lb/hr) to a continuous-circuit, 12-liter, single-tank digester to yield phosphoric acid and byproduct gypsum filter cake. Comparison with earlier data shows that a significantly improved filtration rate was attained in a single-tank reactor compared with that attained in a five-tank reactor train processing the same ore. Iron and aluminum impurities in the product phosphoric acid averaged about 60 pct higher than amounts reported in commercially prepared, concentrate-derived acid. All gypsum filter cakes prepared had a firm, sandy texture, rendering them physically suitable for stacking or landfill use. Introduction of dry attritioning and air classification approximately doubled the attainable filtration rate when the dry-beneficiated product was digested. In air classification, there was a 12-to 14-pct P205 loss. Depending on the technique used and the matrix grade, overall P205 recovery ranged from about 72 to 89 pct.

Jan 1, 1979

By V. A. Nieberlein

This paper presents the results of research undertaken to recover titanium and columbium by low-temperature chlorination of low-grade columbium-bearing ilmenite concentrates, and to simultaneously remove chlorinated impurities from the volatile chlorides without resort to distillation. Coke-reduced ilmenite was chlorinated at 400° to 500° C., and the resulting TiC14 was free of most impurities before condensation. A heated purification column was used wherein various packing materials reacted chemically or physically with the impurities which passed through them in the vapor phase. A nearly water-white TiC14 product was obtained directly. The principal impurities in the titanium tetrachloride were: 0.02 percent Fe, 0.01 percent V, 0.05 percent A1, 0.04 percent Si, and 0.07 percent Cb. This is a less pure product than commercial TiC14. Most of the columbium was recovered as crude CbC15, requiring further refining.

Jan 1, 1960

By Walter K. Utt

The vibration levels of the heavy machines used in surface mining are much greater than for vehicles used on highways. In order to assure the proper functioning of electronic equipment placed on the surface mining vehicles, the U.S. Bureau of Mines has conducted a program of field measurements to define their vibration environment. The information in this report is for a class of vehicle that has a blade for scraping and wheels with rubber tires. The statistical information derived from these measurements can be used as a basis for laboratory testing to qualify equipment for a surface mining vehicle of this class. The envelope that would encompass 99 pct of the vibrations encountered in normal operations is presented for each location on the vehicle. The five locations for which data were recorded are the floor of the cab, the engine, the frame, the drive train (gear, differential, and torque converter), and the axle. Tabulated data are provided for those who wish to use a different probability level. The appropriate test profile for the laboratory testing can be determined from the information presented in this report.

Jan 1, 1993

By D. B. Dow

This paper on the physical chemistry of oil-field emulsions is the last of a series of three prepared as a result of a study of oil-field emulsions. The first paper3 deals with the factors responsible for the formation of emulsions, find the second4 with methods now utilized for dehydrating oil-field emulsions. A more complete report of the whole investigation is in preparation. The laws governing the formation and resolution of oil-field emulsions fall in that branch of physical chemistry doling with colloids. Much work has been done by the physical chemist on colloids And emulsions, and, although most of this work was on commercial and pharmaceutical emulsions, yet the principles developed apply in a general gray to oil-field emulsions.

Jan 1, 1925

By H. S. Chiang, S. S. Peng

"SummaryAir velocity distribution surveys on four mechanized longwall faces are presented and discussed. Although there are discernible patterns in the velocity distribution, there are wide differences in distribution in the cases examined. This can be attributed to differences in mining and face geometry. An important factor is air leakage into the goaf.IntroductionOver the past two years several intensive air velocity surveys have been carried out in West Virginia coal mines as part of a programme aimed at understanding dust transport mechanisms on mechanized longwall faces. These are presented here and some of the patterns of velocity distribution are discussed.Ventilation survey methodologyThe air velocity vector consists of three mutually perpendicular subvectors; the vertical subvector is directed toward the roof, one of the horizontal subvectors is parallel to the coal face and the other pointing to the gob. The air velocity which was measured in this paper is the horizontal subvector parallel to the coal face.To record the velocity distributions at the longwall faces, the surveying stations and the surveying points were established as follows.(1) The first station usually was set at the third support from the headentry T-junction. Within the first few supports, the air coming from the intake airway encounters a sharp right-angle turn at the T-junction, and forms a turbulent region close to the coal face. The intake air in this region is also influenced by the motors that drive the face conveyer. But when the air reaches the different. But for the same face the number was the same. The main air-travelling area was divided into six to 12 equally sized sub-areas, and each surveying point was situated approximately at the centre of the sub-area.The velocity survey was carried out by two persons, one reading the meter and the other taking down the readings. A complete survey at one station took about 5-8 min. Usually, the dimension of the cross-sectional area was measured during that time.A third person used the smoke tubes to observe the following: (I) the air movement patterns at different locations; (2) the extent and the direction of the air leakage; and (3) the machines' influence on the main airflow. At the same time he observed and recorded the roof conditions and the compactness of the roof-caving in the gob."

Mar 1, 1989

By H. W. St. Clair

In about 1930, Degussa applied for a patent on a process for the of oxides, carbides, sulfides, and other nonmetallic impurities by filtration in the molter state. The filtering media listed were wire screen, coke, and ceramic materials, and quartz. It was also suggested that filtration might be combined with chemical reaction between the metal and the filter medium or that might be added to the system. No patent was granted on the general scheme, but several years later a patent was granted on a continuous process purification of crude light metals, especially or alkali earth and their alloys. The melt was stirred at 1 temperature at which the impurities (such as oxides and salts) remained solid and the metal was drawn through a filter tube. The impurities collected under the filter and were removed by a screw conveyor. Crude sodium was purified by this process in Degussa's Knapsack plant. During the last war, when the refining of scrap became a very urgent Problem in Germany, experimental investigations were extended to separation of other metals and metallic compounds by filtration. Preliminary experiments seemed to confirm the opinion of Dr. L. Weiss that the principles of wet chemical filtration might be applied to a great extent in the purification of metal and alloys.

Jan 1, 1949

By Kenneth L. Cashdollar

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRL Lake Lynn Experimental Mine and after laboratory explosions in the PRL 20-L chamber and the Fike 1-m3 chamber. The dusts studied included both high and low volatile bituminous coals. Low temperature ashing for 24 hr at 515°C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as or higher than the initial incombustible content. The MSHA alcohol coking test-was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared to the initial dust loadings to determine the transport distance of dust during an explosion. All of these data will be useful in future forensic investigations of accidental dust explosions in coal mines or elsewhere. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health or the Mine Safety and Health Administration.

Jan 1, 2006

By R. L. Grayson, S. S. Peng

"Abstract. Sampling of respirable dust and analyses of samples have been partially completed for a longwall panel. Physical and compositional properties which have been characterized include:l. Respirable mass concentration, 2. Mineral composition,3. Particle size distribution by mineral,4. Particle shape distribution by mineral,5. Particle angularity distribution by mineral, and6. Respirable size distribution.Analytical techniques used in the characterization of samples are described, and results are reported with emphasis placed on relationships between the various characteristics and worker locations. Details of existing mining conditions, equipment arrangements, dust control methods and operating system parameters are presented.INTRODUCTIONThrough the work of many researchers worldwide, the health of coal miners in modern societies is now protected from dangerous exposure to respirable coal mine dust. A vast amount of research culminated in the exposure-response model of Jacobsen, et al. (1971) whi3h has been used to establish the 2mg/m exposure limit in the United States. According to the model, exposure to respirable dust for 35 years at this level or less would prevent the occurrence of a clinically significant case of coal workers' pneumoconiosis (CWP). The exposure limit, of course, must be adjusted whenever greater than five percent free silica exists in the respirable dust.The Jacobsen model was built around a mass concentration exposure, which showed the highest correlation with incidence and progression of CWP. As Morgan; et al. (1973) noted, howev.er, the quantity of respirable dust inhaled is not the only significant factor. It is noted that although mass of respirable dust correlates highest with the incidence of CWP, it is not a causal factor. Indeed, the insidious processes causing the disease occur on the cell-particle scale, requiring microscopic investigation."

Mar 1, 1989

By H. R. Hardy Jr., E. J. Kimble Jr., H. W. Shen

"The primary objective of this research project is to study the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. Secondary objectives include the investigation of the acoustic emission technique as an indirect method for coal dust characterization and remote bit wear monitoring. The results of the project will be useful in developing efficient coal cutting techniques which significantly reduce the harmful coal dust components, and in providing methods for remote monitoring of bit condition and associated coal dust character. This paper will outline recent experiments carried out on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. During the experiments acoustic emission and a variety of other mechanical parameters were monitored. · A commercially available artificial intelligence computer package, namely: JCEPAK (Intelligent Classifier Engineering Package), has been utilized to provide a powerful and objective means for AE waveform analysis. This program is able to evaluate a number of features of each AE event and to make objective comparisons between AE signals associated with different loading or cutting parameters. Finally, the paper will discuss the results obtained from a variety of coal breakage tests.INTRODUCTIONStudies to date clearly indicate that the reduction of the severity, and eventual elimination, of Coal Workers' Pneumoconiosis (CWP) depends on gaining fundamental understanding in a number of major areas. These include dust generation and entrainment, transportation, suppression, medical effects of dust and possible treatment. At present a project is underway by the authors to investigate the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. An important aspect of this on-going project is the development of acoustic emission (AE) criteria which will make it possible to carry out remote monitoring of coal cutting operations. Suitable on-line analysis of monitored AE data would allow engineers to evaluate factors such as shearer bit condition and cutting efficiency, and to quantify the particle size and shape distribution of the generated dust. The on-going AE studies are fundamental in form and were undertaken to evaluate the general feasibility of AE monitoring techniques using simplified coal cutting procedures. This paper will outline recent experiments on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. Additional information on these studies are presented elsewhere [4]."

Dec 1, 1996

By Donald W. Mitchell, John Nagy, Edwin M. Murphy

To increase safety and productivity in mining , the potential uses and hazards of rigid foam were investigated by the Bureau of Mines Experimental Coal Mine . This research resulted in the development of chemical formulations , spraying equipment , and application procedures that permit safe and effective use of urethane foams for improving mine ventilation , for reducing weathering of mine rock and steel , for constructing seals in fire areas , and for thermal insulation .

Jan 1, 1964

By L. A. Neumeier

The Bureau of Mines evaluated the properties of a Zn-0.75 pct Cu-0.12 pct Ti alloy extruded at temperatures between 400° and 720° F. The extrusions were made with a reduction ratio of 28-to-l and at relatively slow speed. Rod was also extruded at 560° and 640° F with a reduction of 255-to-l. With increased extrusion, temperature, extrusion pressures decreased substantially and creep resistance of the rod improved significantly. Coefficients of thermal expansion were low in the long rod dimension. Microstructures, hardness, and tensile properties were also evaluated, and a limited evaluation was made of bend ductility at 32° F for the rod extruded with the 255-to-1 reduction.

Jan 1, 1969

By Hillary W. St. Clair

This report gives the results of an experimental study of the progressive changes that occur in particle size and size distribution when a homogeneous and isotropic mineral is subjected to crushing by impact. The mineral used in the study was uniformly sized quartz, which was crushed in a simple drop¬-weight machine that applied impact energy up to about 100 kg-cm per g. Screen analyses of the crushed products were analyzed by the method of moments to determine the mean size, variance, skewness, and kurtosis. Analysis of the data from these experiments shows that the mean size of the crushed product is a function of the energy input and the initial size. The size distribution is functionally related to the degree of size reduction. As the mean particle size is decreased, at first there is a corresponding increase in the variance and decrease in the skewness, But, as size reduction is carried further, each tends eventually to approach a steady value, and the form of the size distribution becomes stable.

Jan 1, 1972

By R. W. METCALF, A. G. Charles, F. M. SHORE

To furnish the information frequently requested by producers and suppliers as to the fuel requirements of the Federal Government , the Bureau of Mines , with the cooperation of the consuming departments and establishments , has collected the data herein , showing the Government's fuel consumption during the fiscal year ended June 30 , 1930. The following tables show the quantities and kinds of fuels consumed by the Federal Government in each of its departments and their principal branches , in each State , and in Alaska , Hawaii , Panama Canal Zone , Porto Rico , and the Virgin Islands . The separate departments and establishments were asked to supply information for each Federal building or other plant and , as to vessel fuel , the amount loaded at each port of supply . Fuels consumed in internal combustion engines are not included . The report does not include fuels used by Post Offices of the fourth class , since their fuels are not purchased by the Federal Government but are covered by an allowance in each case for light and heat . In some cases the data supplied represent receipts , which are approximately equivalent to consumption . The present study is believed to be the first effort to bring together the data representing the Government's requirements for the various fuels which it consumes . Figures showing the coal consumed by the Federal Government were gathered for the year 1922. These data are shown in an article by O. P. Hood and R. H. Kudlich of the Bureau of Mines , contributed as a chapter to " Industrial Coal ; Purchase , Delivery and Storage , " published by the American Engineering Council . The figures of coal consumption presented herewith are approximately comparable with those published for 1922 , a relatively small difference being due to the fact that the 1922 figures include the Philippine Islands and all other territory in which any coal was consumed by the Government . At the present time , the only data on Government fuel consumption that are published regularly are those compiled by E. B. Swanson , chief economist of the petroleum economics division of the Bureau of Mines . These are published annually by the Bureau of Mines in " Sources and Distribution of Major Petroleum Products , Atlantic Coast States , " and by the bureau in cooperation with the American Petroleum Institute in the annual " National Survey of Fuel Oil Distribution . " It is believed that the data herewith will prove of interest and value to the fuel industries as well as to Government consumers and that it will also afford a basis for measuring future trends in the use of the various fuels by the Federal Government . Figures showing the quantities of the various kinds of fuels consumed by each of the executive departments and independent establishments , are given in Table 1. It should be noted that when one organization procures and delivers fuel to be consumed by other branches

Apr 1, 1932

By G. H. Cobb, J. L. Johnson, H. H. Heady

An infrared absorbance technique is described for analyzing anodic gases produced during the electrowinning of uranium , thorium , and rare - earth metals in molten fluorides . Typical components determined qualitatively in a gas sample are CO , CO₂ , CF4 , C₂ Fe , C3F8 , COS , CS₂ , and SiF4 . About 20 minutes are required to record and interpret the spectrogram , and report quantitative results for CO, CO₂ , CF4 , and SiF . The procedure is used for control during electrolysis .

Jan 1, 1964

By R. E. Heithecker, Van A. Mills

"Crude oils are capable of dissolving quantities of gas under pressure. This fact has been known for some time, but questions have arisen as to the effects of gas in solution upon the characteristics of the oil. Previous investigations4 show that gas in solution in an oil affects the viscosity and surface tension of the oil, but the effects on the volume and A. P. I. gravity of the oil have not been known. The results given in this report show that there is a decided change both in volume and in the A. P. I. gravity of the oil due to the solution of the gas in the oil under pressure. As gas is dissolved, the volume of the oil and the A. P. I. gravity increase. The converse of this phenomenon is also true: if the gas is released from a saturated oil, there is a shrinkage in volume and a decrease in A.P.I. gravity due to the release of gas from solution. However, various oils show marked tendencies to retain a portion of the dissolved gas upon releasing the pressure to that of the atmosphere. This retained gas has an appreciable effect on the volume and A. P. I. gravity of the oil because the oil does not resume its initial volume or gravity while it retains dissolved gas. In a sense the oil has been ""freshened"" and will not return to its original or weathered volume until it loses some of the lighter fractions. Wiggins5 has shown that a fresh oil decreases both in volume and in gravity because of the weathering of the lighter fractions while the oil is standing in storage tanks.This paper includes data attained during the determination of volume and gravity correction factors to be applied in the oil recovery investigations of the Bureau of Mines. Three oils having a wide range in gravity were used in determining the correction factors. These oils were from the Bartlesville-Dewey field, Oklahoma, the Seminole field, Oklahoma, and the Inglewood field, California. The same gas that was used in the oil recovery experiments was used throughout this investigation. Determinations were made of the volume and A.P.I. gravity increases resulting from the gas going into solution at 200, 400, 600, 800, and 1,000 pounds pressure; also the increases in the volume and gravity of the oil due to retained gas were determined after the dissolved gas was liberated from solution by releasing the pressure to that of the atmosphere.Samples of residual and liberated gas were taken throughout the investigation in order to study the selective absorption and selective retention by the oil of the various constituents of the gas. The analyses of these gas samples showed that there was selective absorption and selective retention of the constituents of the gas. The tests on Inglewood crude gave the most pronounced example of selective absorption and selective retention of the gas.All of the tests were conducted at a constant temperature of 709F."

Oct 1, 1928

By William C. McLaughlin

In the deep vein mines of the Coeur d'Alene mining district, rock bursts are a potential hazard to the mine structure and underground personnel. Damage repair costs are estimated by one company to exceed $1 per ton of ore mined. The Bureau of Mines, in cooperation with the mining companies, has conducted research intermittently over the past 10 years to help reduce bursts. Onsite inspections of major rock bursts were conducted, and reports were submitted to mine management; these included the geology and geometry of the affected area. The paper discusses the development and improvement of microseismic and surface monitoring equipment. The underground microseismic network, when operated on a regular basis and the results plotted daily, is capable of detecting stress concentration in certain areas. The surface seismographs record rock bursts, blasts, earthquakes, etc., throughout the district and show approximate location, time, and relative intensity of the event.

Jan 1, 1976

The principal activities of the Bureau of Mines Explosives Research Center from July 1, 1963 to June 30, 1964 are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1964; in general; the research reported in these publications antedates the report period. Part 3 describes a short-term investigation into safety problems associated with shipping of molten sulfur; this investigation is not at present destined for publication elsewhere.

Jan 1, 1965

By J. E. Tiffany, Gaigler. Z. C.

"PREFACEIn presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 16 and 21 outlining the conditions in use under which, and only under which, the explosive or blasting device is permissible.In view of a recent publication recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 16 and condition 2 on page 21. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.PERMISSIBLE EXPLOSIVES TESTED UNDER SCHEDULE 17CAn active list of permissible explosives was published in December 1937 as part of Bureau of Mines Report of Investigations 3361, under the title ""Active List of Permissible Explosives and Blasting Devices Approved Prior to June 30, 1937.n This list included 196 brand names.Changes in the list that have been authorized to June 30, 1938, placed 7 additional brands of permissible explosives on the active permissible list as a result of tests, changes in brand names, or transfer from the inactive list. Twelve permissible explosives were transferred from the active to the inactive list. The present list contains 191 brand names. The brand names of the permissible explosives placed on the active list are as follows:"

Oct 1, 1938

By R. R. Wells

An important activity of the Bureau of Mines is the continual search for new sources of minerals. As a part of the investigation of strategic mineral deposits in the United States, samples of mercury ores were submitted to the Ore Dressing sections of the Salt Lake City and Albany stations for metallurgical testing. This paper gives data summarizing the results obtained from laboratory beneficiation studies of mercury ore samples submitted during the period 1941 to 1947. Ores tested included three from Jackson County, Oreg., one from Valley County, Idaho, one from Storey County, Nev., and one from Sonoma County, Calif. In general, the ores from Oregon were not amenable to concentration by flotation because of intimate association of cinnabar with other minerals or because of extremely low grade. One Oregon ore was amenable to direct distillation provided lime was added to reduce corrosion of the retort.

Jan 1, 1950