Search Documents

By D. Hinton, M. McCawley, R. C. Lantz, F. Pisano, C. Stanley

"INTRODUCTION Aerosols (5 um have not been shown to be consistently generated and characterized in inhalation chambers. Particle deposition in the lungs however may occur with particles as large as 25 um(1). Therefore, in order to closely simulate the atmosphere of an underground coal mine where the distribution is bimodal, with modes at S and 15 um (2), particles much greater than <1 um must be characterized for uniform mixing and size distribution within these chambers. The Hazelton Animal Exposure Chamber has been chosen because it has been best characterized for smaller particles (<1 um) (3), and is the major type used by most inhalation toxicology institutes such as Lovelace Inhalation Toxicology Institute and Battelle Northwest Laboratory.BACKGROUNDPreviously published studies on the inhalation of solid aerosols have attempted to characterize the distrition of particles of <2 um in diameter. There are no published reports of extensive work characterizing either the size distribution of particles <1 um or the concentration throughout the exposure chamber (Table 1).Table 1 shows the variability and sizes of several aerosols <1 um in diameter used in five previous chamber studies.Discussion of Previous StudiesThe study done by Bauermash, Bryan, Dickinson, and Burke (4)stated two major concerns in the development of the 6.5 ft. diameter chamber. The first was that a quantity of animals could be exposed to the same concentration regardless of the location of the animal, and second was that the chamber could be easily cleaned and decontaminated. The solution to the first concern required a circular chamber with the contamination air entering the chamber somewhere along the central axis. The animals could then be changed during exposure time so that each animal was exposed throughout the total volume."

Jun 1, 1988

By Harold M. Smith

Important discoveries of new oil fields were made in 1937 in the State of Illinois. Oil production, which was virtually constant during 1934, 1935, and 1936 at about 4,400,000 barrels a year, a increased to 7,499,000, barrels during 1937, and in 1938 this production was trebled. In 1939, 94,302,0003/ barrels were produced (almost four times the 1938 quantity), making Illinois one of the cost important oil-producing areas in the United States. The Bureau of Mines has analyzed 35 samples of petroleum from these new Illinois fields and presents the analyses herein. Included with them in this report are analyses of seven samples from fields developed before 1936.

Jan 1, 1940

By Harold M. Smith

[Important discoveries of new oil fields were made in 1937 in the State of Illinois. Oil production, which was virtually constant during 1934, 1935, and 1936 at about 4,400,000 barrels a year, a increased to 7,499,000, barrels during 1937, and in 1938 this production was trebled. In 1939, 94,302,0003/ barrels were produced (almost foot times the 1938 quantity), making Illinois one of the cost important oil-producing areas in the United States. The Bureau of Mines has analyzed 35 samples of petroleum from these new Illinois fields and presents the analyses herein. Included with them in this report are analyses of seven samples from fields developed before 1936.]

Jan 1, 1940

By Jack W. Carlson

Considering the magnitude of today&apos;s public concern with critical mineral and fuel materials, regarding both their midterm and long term availability, the Nation is fortunate to have in place and operating the coordinated data systems of the Geological Survey and the Bureau of Mines. Under the supervision and policy direction of the Assistant Secretary--Energy and Minerals, these Department of the Interior agencies have long been responsible for important mineral activities in the Federal Government. Aside from their highly respected mineral industry publications such as the monthly Mineral Industry Surveys, annual Commodity Data Summaries and topical Professional Papers and Reports of Investigation, the Bureau of Mines and Geological Survey data bases and expertise have been readily available for use in emergency situations. Policymakers and decisionmakers in government have placed major reliance upon this ready mineral data and analytical capability in World War II, the Korean War, the recent price control era, and the Arab oil embargo.

Jan 1, 1975

By Raymond B. Lucas

"Distinction between Tripoli and Diatomaceous EarthMuch confusion exists both in the literature and in the trade as to the proper use of the terms tripoli, tripolite diatomeceons or infusoriai earth, and kieseigunr. All of these terms are often used synonymously by the trade and even in mineralogists and other reference books. Actually, tripoli is a ma- is a material of definite and distinct physical and chemical properties and all of the other terms belong to a different material with just as definite and distinct properties.Originally the term tripolite (loosely called tripole) was given to a diatomaceous cart from Tripoli in Northern Africa. Dena (J.D. Dana, A System of Mineralogy 6th Ed.) calls this material tripolite and gives no authority for the use of the terms tripoli. Between 1880 and 1890 the deposits near Missouri, were opened and the material placed on the market as ""Tripoli"" no doubt due to its resemblance in some respect to the original tripolite or diatomaceous worth from Tripoli. Since that time the term tripoli has with increasing definitenesss been reserved for the Seneca material and other siliceous of similar origin and physical properties, while all siliceous material of organic origin, containing dilators, has been called diatomaceous earth (or its synonyms infusorial earth, kiselguhr, etc.). Rottenstone is sometimes classed with tripoli."

Nov 1, 1920

This report describes a U.S. Bureau of Mines investigation into the removal of gate road chain pillars in conjunction with longwall retreat mining. The research objective was to determine, through evaluations of the loads imposed on the gate road pillars and supplemental support elements in the entries, how the pillars, supplemental support, and entries were affected by the longwall abutment pressure. To achieve this goal, vibrating wire stressmeters and hydraulic flat jack pressure cells were installed in the support elements to monitor stress change caused by abutment pressure as a function of longwall face advance. The findings documented in this report are the result of information collected from instrumentation and observation at the mine. Pillar and support loading measurements and stability observations revealed that the roof and the support elements remained stable during panel retreat, while the face progressed at a normal rate of advance. The ability to safely and efficiently mine chain pillars during panel retreat increases resource recovery and can provide several other benefits described in this report.

Jan 1, 2010

By K. E. Hjelmstad

During an underground mine fire, air can be rapidly depleted of oxygen and contaminated with smoke and toxic fire gases. Any delay in warning miners could have disastrous consequences. Unfortunately, present mine fire alarm systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in mine area coverage. Recent research by the U.S. Bureau of Mines has demonstrated that ultra low frequency electromagnetic signaling can be used for an underground mine fire alarm. In field tests of prototype equipment at five mines, electromagnetic signals from 630 to 2,000 Hz were transmitted through mine rock for distances as great as 1,645 m to an intrinsically safe receiver. The prototype system uses off-the-shelf components and state-of-the-art technology to insure high reliability and low cost. When utilized, this. technology would enable simultaneous and instantaneous warning of all underground personnel, regardless of their location or work activity, thereby increasing the likelihood of their successfully escaping a mine disaster. This report presents the theoretical basis for through-the-rock ultra low frequency electromagnetic transmission, design of the prototype transmitter and receiver, and the results of in-mine tests of the prototype system.

Jan 1, 2010

By Albert J. Rambosek

The objective was to obtain qualitative information on (1 ) the stress field in a core stub at the bottom, or face , of a cored borehole and (2 ) whether , and at what distance , in terms of core diameters from the face of the borehole , relief of stresses in the core is complete . The photoelastic and brittle lacquer techniques of stress analysis were used to determine the pattern of stresses in two- dimensional models , simulating the bottom of a borehole with a projecting stub of core . The core was stress- free at 1-1 /2 core diameters or more from the face of the simulated borehole . The analyses of the isoclinic and isochromatic patterns in the core near the face of the borehole reveal why core occasionally breaks into thin plates , when core or stress - relief drilling is attempted in highly stressed rock masses , such as heavily loaded mine pillars . stub broke away from the bottom in a hydrostatically loaded artificial rock specimen in a manner indicating that core " wafering" can result from tensile stresses developed in the core when a coring bit penetrates the highly stressed rock mass .

Jan 1, 1964

By E. R. Cole

The Bureau of Mines developed a procedure that enables substitution of zinc cathodes for the aluminum cathodes normally used in commercial zinc electro-winning. Using zinc cathodes eliminates the necessity for stripping and makes it possible to electrowin zinc from solutions derived from material containing excessive amounts of soluble fluorides; for example, zinc concentrates obtained as a byproduct of fluorspar mining in Kentucky and Illinois. To demonstrate the viability of using zinc cathodes, fluoride-containing zinc concentrate was roasted, leached, and purified according to current commercial practice. Electrolysis was carried out in 0.8-, 1-, 5, and 10-liter cells at 35° to 40° C with a cathode-current density of 8 amp/dm2 in a solution containing 65 g/l Zn++ and 200 g/l H2S04 using PbO2 anodes. Zinc deposits were produced on zinc cathodes with good morphology and excellent current efficiency (90 to 94 pct) in solutions containing enough fluoride (~0.5 g/l, F+) to cause sticking of zinc to aluminum cathodes. The approach described has failed previously because of severe solution-level corrosion of the zinc cathodes. The present investigation found that the use of a simple mechanical barrier to prevent oxygen migration from the anode was sufficient to prevent solution-level corrosion of the zinc cathode starting sheet.

Jan 1, 1979

By Adrian J. Mathias

This report presents the results of an investigation of a mine production-scheduling model and a critical path analysis for long-range mine planning. An example is given to illustrate how these techniques might be used to plan long-range development and production scheduling for a large underground mine. The model, based on estimated ore block grades and tonnages, and on designed mine development layout, simulates mining of ore blocks in a sequence necessary to fulfill mill requirements for ore tonnage and grade evaluation within pre-established system restrictions. Simulated production schedules are obtained as output from the model. These production schedules are then incorporated into a critical path analysis to determine the sequence for the long-range development work so as to fulfill the production schedules and thereby meet the ore grade and tonnage requirements of the mill.

Jan 1, 1967

By Lee J. Raabe

A specialized loading system for tensile and fatigue testing of wire rope was constructed and installed in the U.S. Bureau of Mine Wire Rope Test Facility in Bruceton, Pennsylvania. The computer-controlled closed-loop servo-hydraulic test system which can apply up to 800,000 pounds of force on the rope while stretching it up to 30 inches will be used in the development and verification of hoist rope retirement criteria for ropes in the 1 to 2 ½ in. diameter range. Characteristics and capabilities of the system are discussed.

Jan 1, 1984

By James Paone

The Bureau of Mines studied the behavior of rocks at the initial state of crater formation that results from the stresses created under a drill bit to determine which mechanical properties of rock are important in rock fragmentation by drilling. Although a definite relation between the drilling strength and relevant mechanical properties has not been established, maximum yield strength of rock is apparently a parameter of drillability of rock. The strengths of rock were considered from the Mohr-Coulomb criterion from which the surface of failure was constructed. The results from previous tri-axial tests on Solenhofen limestone were adopted to verify the criterion of failure. Inelastic behavior of some rock types was observed under a low-velocity impact of a hemispherical bit and under static indentation with a similar bit. Quantitative determinations of strengths of Solenhofen limestone) Indiana limestone, and Tennessee marble were made under static indentation. The maximum yield strength estimated from the average stress over the indented area was used as the crushing strength of rock under a drill bit.

Jan 1, 1966

By G. L. Oldright

By means of a technique developed in cooperation with the Eagle-Picher Mining & Smelting Co. and outlined in the first report of this series (R. I. 4333 ), it was possible to take many thermocouple readings with base-metal couples at temperatures over 2300° F with unsupported protection tubes for over half the lengths of the Henryetta retorts. -This technique made it possible to avoid the use of the usual optical pyrometer, which gives temperatures dependent upon the luminosity of the flames, and which is not conveniently usable to read temperatures for the lengths of the retorts from the front of the furnace. The temperatures of the retorts themselves were necessary in order to set upper limits for safe operation; the lower limits of operating temperatures are set by the zinc content of the retort residues. The zinc content left in the retort residues for various sections of length also varies with retort temperatures rather than with flame temperatures. The variations in temperature along the retort can then be used as guides to distill more zinc from the residues, to avoid fluctuations in the rates ,of flow of zinc vapor into the condenser and to employ lower temperatures if such rates become high enough to cause losses of uncondensed zinc.

Jan 1, 1948

By H. J. Coleman

Knowledge of the types of naturally occurring sulfur compounds in petroleum is of both theoretical and practical interest to petroleum chemists and geologists. This knowledge has been extended by the identification of 77 sulfur compounds, including 36 thiols, 23 chain sulfides, and 18 cyclic sulfides in a 111° to 150° C boiling range distillate of Wasson, Texas, crude oil. The characterization procedure used in separating and identifying these compounds included isothermal distillation, vacuum fractionation, liquid-solid chromatography (alumina adsorption), chemical treatment, gas-liquid chromatography, microdesulfurization, and infrared analysis. The procedural steps described represent a systematic method of sulfur compound analysis considered applicable for determining the nature and concentration of the sulfur constituents present in any straight-run petroleum distillate of the above-boiling range.

Jan 1, 1966

By W. R. McDonald

Part of the U.S. Bureau of Mines mission is to supply the U.S. mineral industries with information that is useful in planning to meet the Nation&apos;s critical and strategic mineral needs if a national emergency occurs. The Bureau conducted laboratory research including operating a nominal 100 lblh pilot plant to demonstrate the recovery and concentration of chromite by gravity and flotation operations from three northern California mineral deposits. Gravity beneficiation test results show that concentrates contained as much as 52 pet chromic oxide (CrZ03) with recoveries of about 80 pet. Results from the bench-scale unit operations of mineral liberation, tabling, vanning, spiraling, pinch sluice, work index, and thickener area determination tests are presented in this report.

Jan 1, 1990

By John C. Machisak

THIS INFORMATION CIRCULAR covers the calendar year 1055 and contains statistical data on employment and injuries pertinent to metal and nonmetal mining and to their mills and processing plants that are voluntarily reported annually to the Federal Bureau of Mmes. This report, unlike previous publications, lists not only production and development workers but also office employees associated with mining and milling or processing. The last publication m the series, Information Circular 7798, Injury Experience in the Metal and Nonmetal Industries, 1954, also contains unpublished injury and employment statistics for 1943 through 1953. The Bureau is authorized to request data on injuries and employment from operators in the metal- and nonmetal-mining industries. The information voluntarily submitted by these operators contributes immeasurably to the promotion of safety in the mineral mining industries as it discloses the hazards to which metal and nonmetal workers are continually exposed during mineral extractive operations.

Jan 1, 1959

By M. J. Ferrante

A process was investigated for preparing Specification-grade nickel (containing less than 1 percent cobalt) by stripping it electrolytically from a nickel sulfate-boric acid solution and using the stripped electrolyte for the preferential dissolution of nickel from basic carbonates of nickel and cobalt. The basic carbonates were produced at the plant at Nicaro, Cuba, owned by the U.S. Government. Determination of the optimum conditions for deposition of Specification-grade nickel indicated that the upper limit of cobalt concentration was 0.1 gram per liter. The pH, temperature, and concentrations of nickel and boric acid in the electrolyte were not critical. An aluminum cathode and two lead anodes were used at a cathode current density of 1.2 amperes per square decimeter.

Jan 1, 1959

By Raymond W. Hiteshue, Sam Friedman, Martin D. Schlesinger

The Bureau of Mines in cooperation with the El Paso Natural Gas Co. investigated the effect of high temperature and pressure at short residence times on the hydrogenation of a New Mexico coal to gaseous and liquid hydrocarbons . The study was made in a bench - scale semicontinuous unit at pressures of 500 to 6,000 psig , 480 ° to 1,000 ° C , and residence times of less than 1 minute to 15 minutes . Ammonium heptamolybdate was impregnated on the coal to furnish 1 percent molybdenum based on maf coal . Coal could be rapidly hydrogenated at elevated temperatures and pressures to yield large quantities of gaseous hydrocarbons and small quantities of lowboiling oils , high in single - ring aromatics . At 800 ° C and 6,000 psig and a residence time of 1 minute , the yield of hydrocarbon gas was 43 percent and of liquid hydrocarbons 9 percent , based on maf coal . With a 15 - minute residence time , the yield of gaseous hydrocarbons increased to 68 percent with a decrease in yield of oil to 6 percent . At higher hydrogen velocities , the yields of oil were much greater but contained large quantities of asphaltene . Low concentrations of molybdenum (0.01 and 0.1 percent ) or a high concentration of iron ( 1 percent ) were ineffective at 800 ° C , 6,000 psig , and short residence time .

Jan 1, 1964

By W. M. Traver

During World War II, the Bureau of Mines investigated a large number of ore deposits in the United States and Alaska in a search for domestic sources of strategic minerals. Deposits chosen for exploration included those expected to contain metals of importance in the successful prosecution of the war. This report describes exploration of a district of known antimony occurrence on Coyote or Antimony Creek near Antimony, Garfield County, Utah. A preliminary report by Paul T. Allsman, Chief of the Bureau&apos;s Salt Lake City branch made in August 1941, recommended further investigation, and proposed methods for performing the work. The project, begun in November 1941 and completed in January 1942, included trenching and sampling in four of the most promising parts of the area The Federal Geological Survey cooperated in the work by detailed mapping and assisted in the interpretation of geologic data.

Jan 1, 1949

By J. E. Matta

The methane gas emitted from coal samples collected from the conveyor belts dumping into silos was measured by the Bureau of Mines. Approximately 50 pct of the total gas desorbed into a sealed can within 1 week was released during the first 24 hours. No simple correlation between the gassiness of the coal stored and the methane concentration in the silo open space above the coal was found. This was probably because the gassier coals were stored in open-top Silos, which were better ventilated. Although the methane concentration in the open space above the coal pile was less than 1 pct for all 34 silos investigated, a methane measurement in the coal pile showed that high methane concentrations can exist. The methane released in the pile appears to accumulate and not liberate freely into the open space above the coal pile. Probably this gas is released during reclaiming operations, but further research is required to substantiate this claim.

Jan 1, 1978