Search Documents

By A. W. BELDEN

Among the investigations that the Bureau of Mines is conducting witha view to increasing efficiency in the utilization of fuels belonging to or for the use of the Government is an investigation of the processesthat take place in a foundry cupola during a melt. Some observations on the results of cupola tests of cokes at the Government fuel-testing plant in St. Louis, Mo., the coke being fromcoal from many coal fields of the United States, have been stated in a previous bulletin.s Especial attention was given to the meltinglosses that resulted from the use of different grades of coke, light and porous or heavy and dense. These losses amounted in one instance to 52.5 per cent of the iron charged and showed, in convincing manner, the need of exact information in regard to conditions in the fuelbed of the cupola.b Melting losses of iron have been fully appreciated but little under-- stood. The fact that these losses were possible with either light or heavy coke led to the belief that by using small charges 80 placed that. melting would take place in that zone of the cupola where the highest heat and the smallest percentage of oxygen prevailed and by confiningall melting to this zone these losses would be eliminated and the economical use of practically any coke produced for metallurgical purposes would become possible. This widening of the field from whichcoke might be drawn for foundry purposes would serve to place the foundryman in an independent position as regards his source of supply, and would tend to conserve the better grades of coking coals, which are being rapidly exhausted, by making the poorer grades available for mixing with them. In order to investigate conditions within a cupola, the Bureau of Mines as a first step decided to install a commercial cupola, to sample the gases during their travel from the tuy~res upward, and to determine the temperature of the fuel bed.

Jan 1, 1913

By A. J. Kraemer

[The Bureau of Minas for a number of years has been studying the properties of crude petroleum from producing fields in the United States and Western Hemisphere and has published a series of reports on these fields, including oil fields of Texas.5]

Jan 1, 1927

By John P. Powell

The increasing demands for petroleum and its products and the steadily increasing cost of discovering and developing new oil fields are factors that emphasize the importance of increasing the recovery of oil from known petroleum reserves. Water flooding is a valuable conservation measure, not only preventing premature abandonment of stripper leases but also reviving interest in many areas previously abandoned. The use of water flooding as a means for recovering additional oil from partly depleted oil-bearing formations was first tried in Oklahoma in 1931. Early water-flooding operations were confined to the area of shallow Bartlesville-sand formations in Nowata and Rogers Counties, where many of the projects were outstandingly successful. The results of these operations stimulated activities in other pools in Oklahoma, and by the end of 1949 water flooding had been tried in 25 of the 49 oil-producing counties in the State (fig. 1). Approximately 33 million barrels of oil, or 1,806 barrels per acre, had been recovered by December 31, 1949, from 18,221 productive acres included in the 162 active and abandoned projects in Oklahoma by injection of approximately 449 million barrels of water.

Jan 1, 1951

By H. Polat, Q. Hu, S. Chander

"The collection efficiency of dust particles was determined in a laboratory dust chamber equipped with a water spray. Measurements were made in the presence of selected nonionic, cationic and anionic surfactants. For the nonionic and the anionic reagents, efficiency was maximum in a narrow range of concentration. The surfactant concentration corresponding to high collection efficiency was usually much below the commonly used concentration of l "", however. In comparison, much higher collection efficiency was observed for a cationic surfactant at extremely low concentrations. For delineating the mechanism of capture of dust particles, surface tension and contact angle results were used to obtain a correlation between the work of adhesion and the efficiency of collection. Such a correlation was reasonable for the nonionic surfactants but not for charged surfactants. In the latter case, electrostatic interactions between charged droplets and particles were more important, especially for the cationic reagent. INTRODUCTIONSeveral methods are used to control dust in mines. These include: ventilation, foam, scrubbers and sprays. This article is concerned with improving the effectiveness of water sprays, which are widely used to remove dust particles during continuous mining, by adding small quantities of surfactants. Water sprays produce small droplets which act as collectors of dust particles suspended in air. Sprays directed at the actual source of dust have the additional property of wetting the coal before the ·particles become airborne (Hamilton, 1974). Wetting agents, also called surfactants, arc known to play an important role in many applications where dust is a problem. However, conflicting reports exist in the literature with regard to the effectiveness of surfactants in water sprays (for a review, see Chander et al., 1988). In spite of the conflicting reports, the use of surfactants for dust control has increased over the years. In a recent study by the Bureau of Mines, a 27'6 reduction in respirable dust levels was observed in a mine test when surfactants were added to sprays (Foley, 1991)."

Mar 1, 1992

By John O. Atkins

[Experiments were conducted by the Bureau of Mines on five types of simuated lunar rock (dacite, tholeiitic basalt, vesicular basalt, pumice, and uluth Gabbro) to study the effects of various simulated lunar environments n their strength and deformational properties. Specimens were tested in an ltrahigh vacuum (UHV) system at pressures ranging from atmospheric down to 0-11 torr and at temperatures of -130°, 20°, and 135° C. All tests were onducted with a servocontrolled testing machine. Rock specimens tested at 0° C in UHV exhibited significantly higher compressive strength and Young's odulus than those tested at 20° C in atmospheric pressure. The magnitudes f increase are related to the porosities and permeabilities of the rock pecimens; high porosity and permeability allow better outgassing and thus nprove surface cleanliness in UHV. The compressive strength generally ncreases but Young's modulus decreases as test environments change from 20° C i UHV to 135° C in UHV. No significant difference was observed in the iysical properties measured at 20° C in LTV and -130° C in UHV. Anisotropy i strength and Young's modulus exist both in UHV and at atmospheric condi¬'.ons with the same symmetry pattern. The orientations of the principal axes iy, however, change from the atmospheric to UHV condition. The results idicate that rock fragmentation in lunar environment will require more ergy than that at 20° C in atomospheric pressure.]

Jan 1, 1974

By R. V. Ramani

In this report, the application of the Open Pit Materials Handling Simulator (OPMHS) to a mine located in Illinois using bucket wheel excavator (BWE) and a stripping shovel in tandem for overburden removal is described. The specific objective of the study is to demonstrate the application of the simulator to analyze mine planning and scheduling problems and to generate and analyze alternatives for increased production. On the basis of the simulations it was concluded that the maximum productive capacity of the system in raw coal was around 3000 tons per shift. At this production level, the equipment combination and availability also satisfy the match requirements for the stripping shovel and the BWE, and the overburden and coal removal systems. Several alternatives requiring new equipment are proposed and analyzed for increasing production. However, no economic analyses of these proposals were done.

Jan 1, 1977

By Northcutt Ely

This volume summarizes mining and petroleum legislation in 25 jurisdictions of East Asia and the Pacific. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identification of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis of the laws governing mines and quarries and their products; and third, analysis of laws applicable to natural gas, petroleum, and related materials. Where pertinent, sections dealing with historical background or administration have been added. In countries where minerals are subject to control of States or Provinces, those areas are considered separately from the central government.

Jan 1, 1971

By R. S. Dean

In the early days, most smelters were erected in nonarable land and at some distance from settled communities. The movement of population, which resulted in many instances from employment at the smelters, has brought to most smelterman in the United States the problem of preventing damage to plant and animal life in the territory adjacent to the smelters by sulphur dioxide gas (S02). This problem has been met, broadly, in two ways: (1) By diluting and removing the S02 by means of air currents and (2) by converting the S02 to a liquid or solid compound of sulphur and disposing of the compound.

Jan 1, 1937

By R. S. Dean

In the early days, most smelters were erected in nonarable land and at some distance from settled communities. The movement of population, which resulted in many instances from employment at the smelters, has brought to most smelterman in the United States the problem of preventing damage to plant and animal life in the territory adjacent to the smelters by sulphur dioxide gas (S02). This problem has been met, broadly, in two ways: (1) By diluting and removing the S02 by means of air currents and (2) by converting the S02 to a liquid or solid compound of sulphur and disposing of the compound.

Jan 1, 1937

By Staff

This U.S. Bureau of Mines publication presents the results of investigations into the fire and explosion hazards of oil shale rocks and dust. Three areas have been examined: the explosibility and ignitability of oil shale dust clouds, the fire hazards of oil shale dust layers on hot surfaces, and the ignitability and extinguishment of oil shale rubble piles.

Jan 1, 1989

By R. F. Zaffarano

Reservoir oil in the Greater Aneth area, Utah, part of the Paradox basin, was studied to detect variation in oil characteristics within the reservoir and to determine its relation to age of accumulation and fluid equilibrium. At least three subsurface oil samples were obtained from each of the four largest of five field divisions comprising a producing area of 45,000 acres. Height of the oil column in the Pennsylvanian Desert Creek zone is about 230 ft. In general, the oil characteristics were found to be uniform across the area, and averages were developed for use in engineering applications. Average saturation pressure was 1,780 psia; the oil was undersaturated at the initial reservoir pressure, 2,200 psia. Variation in saturation pressure shows a lack of complete fluid equilibrium and continuing diffusion of solution gas from the main body of the reservoir to two extensions linked by narrow arms. By assuming early accumulation, the time involved in this diffusion process was calculated to be about the same as the age of the reservoir formation. Cause of the concentration of gas in the main body is attributed to differential entrapment during accumulation of oil and gas from an exterior source.

Jan 1, 1963

By W. N. Patterson

The three major objectives of this contract were (1) to survey underground diesel-powered mining machinery to determine noise exposure problems, (2) to recommend noise control techniques, and (3) to develop a technique for predicting underground sound levels from surface sound power measurements. The objectives were achieved. The contractor developed information on the severity of the noise problem caused by diesel engines underground and pinpointed the equipment causing the problems. He recommended a number of corrective techniques that can provide relief until long-term solutions are found. A procedure for predicting underground noise levels from above-ground measurements of the machine noise was found valid for several cases tested.

Jan 1, 1975

By G. E. McElroy

The purpose of tins paper is not to present new date on the pressure losses due to bends and chances of area in mine openings through which air flows, but rather to correlate existing data, determined mainly on small duct systems and expressed in a variety of ways, according to uniform methods that facilitate their use in pressure-loss computations. These are required in such, air-flow problems as determining the quantity that will flow through is mine openings under a certain pressure difference or, conversely, the pressure difference that will be required to maintain a certain rate of flow. Air flowing through h ducts, such as mine airways, encounters resistance to flow due to interference of the individual air streams with each other caused by the wall surfaces. The result is that part of the kinetic energy of the flowing stream is converted to heat; and constant renewal of the kinetic energy from the total energy of the flow is required to maintain it. This process manifests itself by a decrease of the total pressure (static pressure plus velocity pressure; of the air in the direction of flow; in order that flow pray occur, there must necessarily be a differences in total pressure between the two cads of the air-ay equivalent to the pressure losses occasioned by the flow, which automatically adjusts itself in magnitude to the pressure difference maintained.

Jan 1, 1932

By Federick W. Miller

The Bureau of Mines has investigated the availability of columbium from 19 deposits (3 producers and 16 nonproducers) in 7 market economy countries (MEC?s). Brazil has the largest recoverable columbium resource, posessing approximately 2.39 million metric tons Wmt), or 69 pet of the MEC total (3.47 Mmt). The Western Hemisphere countries of Brazil, Canada and the United States contain 3.14 Mrnt of recoverable columbium or 90 pnt of the MEC total. Columbium recovered as a byproduct of tin mining is not included as part of MEC resources in this study. Currently producing mines are Araxa and Catalao in Brazil, and Niobec in Canada, These three mines have 2.42 Mmt of recoverable resources or approximately 69 pct of the MEC total. It is estimated that these mines, operating at full capacity, could satisfy cumulative MEC demand (based on an annual growth rate of 5.1 pct) for the next 20 yr. The United States is totally dependent upon foreign sources for its columbium supply. The majority of U.S. columbium is imported from Brazil in the form of steelmaking- grade ferrocolumbium. Canada has been the sole source of pyrochlore concentrates since Brazil discontinued exports in 1981. The United States also imports small (but important) quantities of columbium as columbite concentrates from Nigeria and Brazil, as columbite contained in tin slags from Thailand and Malaysia, and as synthetic concentrates from the Federal Republic of Germany.

Jan 1, 1986

By Mackenzie Burnett

An inducer-type pump, capable of injecting dry coal into a hydraulic transport pipeline has been developed and installed in a specially designed and fabricated slurry injector vehicle. The full scale prototype injector system can deliver up to 11 ton/min of coal into an 8-in pipeline t pressures up to 95 lb/in2. The Helical Inducer Injector operates on centrifugal principles with flow passing axially through helical pitched conical rotor. Water is delivered to the pump through an annular slot at the atmospheric pressure coal inlet. The spinning rotor maintains an air-core vortex of water which pressurizes the discharge housing. A screw feeds coal through the open inlet into this vortex. The inner radius of the vortex contracts as pressure is increased, giving a limiting maximum pressure which is proportional to the square of the rotor speed. Below this limit, flow rate, discharge pressure, und rotor speed re independent variables. The self-powered, 4 -in high slurry injector vehicle follows and receives ROM coal from a continuous miner, reduces the top size to 3-in, and delivers the sized coal to the injector feed screw for slurry formation and pumps it through a mobile hose attached to the vehicle's outby end.

Jan 1, 1983

By L. J. E. Hofer

This Bureau of Mines study, part of a broad program of research in air pollution related to minerals, was conducted to determine the nature and extent of the poisoning of catalysts when used to remove certain air pollutants from exhaust gases. The poisoning examined in this investigation occurs when leaded gasoline is used as a fuel for automotive engines. This research was conducted in cooperation with the Public Health Service. The smog in the Los Angeles area is attributed to the effect of radiant energy on the mixture of hydrocarbons and nitrogen oxides found in the atmosphere there. A large portion of the hydrocarbons is believed to originate in the exhaust gases of automobiles. To prevent the escape of these hydrocarbons into the atmosphere catalytic mufflers have been proposed. In principle, these are simple and nonmechanical, consisting of a vessel charged with a catalyst capable of destroying the exhaust hydrocarbons by catalyzing their oxidation. However, these catalysts are severely affected by the particulate matter, mainly in the form of lead sulfate (PbS04), lead oxysulfate (PbS04.Pb0), and Lead chlorobromide (Pb(Cl,Br)2), contained in the exhaust gas. Deposition of lead on the catalyst as PbS04, PbS04, PbS0, and Pb(Cl,Br)2 restricts catalytic activity. As a result,after 20,000 miles of operation the temperature necessary to achieve 50-percent conversion of isopentane in a mixture of 0.2 percent isopentane, 2 percent carbon monoxide and 4 percent oxygen, and the balance nitrogen at 10,000 hourly space velocity has risen from 400° C. to 500° C. even with a catalyst taken from the exit portion of the catalyst bed. The rest of the catalyst was more severely affected. Therefore, it would appear that operation for 20,000 miles is near the limit for a catalyst.

Jan 1, 1963

By Donald P. Blasko

The Bureau of Mines investigated two areas of oil and gas seeps in the north-central Gulf of Alaska--Katalla River to Bering River and Cape Yakataga to Yakutat Bay to determine (1) whether previously reported seeps are still active, (2) the characteristics of the seeping hydrocarbons, and (3) the amount of bitumen contained in the drainage leaving the seeps and entering the Gulf of Alaska. Thirteen separate oil seeps, six bitumen deposits, and eight gas seeps were located, sampled, and analyzed. The oils ranged from 35.2° to 14.1° API gravity and had sulfur contents from 0.53 to 1.31 wt-pct. Bitumen samples had API gravities from 2.4° to 14.6° and sulfur contents from 0.28 to 0.88 wt-pct. Gas samples had specific gravities ranging from 0.577 to 0.883 and caloric values from 724 to 1,427 Btu/cu ft. A total of 63 water samples obtained from seep locations and seep drainages were analyzed by atomic absorption spectrophotometry for ionic content and by solvent extraction for hydrocarbon content. Although some of the water at the oil seeps had a bitumen content as high as 246,000 mg/1, the amount of hydrocarbons actually reaching the Gulf of Alaska averaged <0.2 mg/1.

Jan 1, 1976

"For a good many years the Bureau of Mines and various state mining experi¬ment stations have endeavored to develop some method of utilizing the immense deposits of lignite in the United States. Work in relent year has indicated that the best method of this is to drive off the moisture and most of the volatile water from the lignite in some form of carbonizing apparatus leaving a residue high in fixed carbon and low in moisture and volatile matter, which by briquetting can be made into a high-grade fuel. The earlier forms of carbonizing equipment tried were complicated, costly to build and keep in repair, and could not be operated intermittently without being seriously damaged. During the year 1922, however the Bureau of Mines devised a very simple carbonizing oven which produces a uniformly well carbonized product. This oven is essentially a vertical shaft with means for supplying raw lignite at the top and discharging the carbonized limited at the lower end. Air in regulated amount is admitted to the shaft at two horizons, and a zone of combustion maintained through which the column of lignite passes. The lignite is thus carbonized by construction of its contained matter and a small proportion of its fixed carbon, leaving most of the fixed carbon in the carbonized product or ""char"". The degree of carbonization can be closely controlled by varying the volume of air supplied to the oven and the rate of travel of the charre down the shaft.The ""lignite char"" produced is a soft material resembling charcoal more than coal or coke, but somewhat harder than charcoal. A typical analysis is shown in the table headed ""Fuels,"" further on in this papers."

Feb 1, 1924

By O. C. Ralston

Natural or artificial manganese dioxide of a grade pure enough to be satisfactory as depolarizer for dry cells has never been available in large supply simultaneously with being available in desired quality . The Second World War called for more of it than ever . A supply of natural material from the Gold Coast was ample for the war and was not completely exhausted . Whereas the crystal form of the manganese oxide was not recognized as a matter of importance until the war came , it is now known that gamma MnO2 is a desirable form and that pyrolusite , once thought acceptable , is not the best mineral . The following paper is a translation of an internal company report filed at the Bitterfeld office of the I. G. Farbenindustrie A.G. by Dr. Peter Marx in 1933 , just a year after G. W. Nichols had published in the Transactions of the American Electrochemical Society a study of making anodic manganese dioxide from solutions of manganous sulfate . The I. G. experiments were made to confirm the American work and were also extended to a larger scale . Only chemical purity was considered , and no mention is made of crystal form . The report adds to the knowledge submitted by Nichols but has not been previously available to the general public . Believing it of value to the United States industry , a translation has been made .

May 1, 1948

By David H. Yee

Because of environmental concerns, the Bureau of Mines investigated an anhydrous chlorination process for the recovery of copper from chalcopyrite, Pelletized concentrate was reacted continuously with chlorine in a vertical shaft reactor at 550° to 750° C to extract copper-iron chlorides and elemental sulfur. The resulting molten metal chlorides drained from the reactor and collected in a receiver while sulfur distilled from the top and condensed in a separate unit. The tests were conducted in a 10-cm-diam reactor constructed of glass and in l5-cm-diam reactors constructed from various refractory materials. A high-alumina ramming mix exhibited the best resistance to molten metal chlorides and elemental sulfur in chlorine atmospheres. A reactor made with this high-alumina refractory was operated for 55 hr under actual chlorinating conditions without suffering any deterioration. Tests results show that more than 96 pct of the chalcopyrite was converted to copper-iron chlorides and elemental sulfur. Good separation of the metal chloride and sulfur products was achieved. After filtration, elemental sulfur of greater than 99 pct purity was obtained.

Jan 1, 1977